N39040-17-T-0185_Attachment_1_-_YFN_1204_SOW.pdf

SHIP: YFN 1204 (YFN 1204) ITEM NO: 077-01-001

COAR: 16 PCN: YFN1-B077

CMP: NONE

PLANNER: ROBERTS, JEARLD

SSP: BOST-517-17 1 of 5 ITEM NO: 077-01-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

1. SCOPE:

1.1 Title: Hazardous Waste Produced on Naval Vessels; control

1.2 Location of Work:

1.2.1 Throughout the Ship

1.3 Identification:

1.3.1 Not Applicable

2. REFERENCES:

2.1 Resource Conservation and Recovery Act (RCRA)

2.2 49 U.S.C. 5103, Federal Hazardous Materials Transportation Act

2.3 Applicable Hazardous Waste Manifest Form

2.4 10 U.S.C. 7311

3. REQUIREMENTS:

3.1 Manage and dispose of all hazardous waste listed in 3.5 in accordance with 2.1 and 2.2.

3.1.1 When a Navy generator number is required by this Work Item, submit the original of 2.3 to the SUPERVISOR for assignment of Environmental Protection Agency (EPA) or delegated state environmental agency identification number.

3.1.2 Manage and transport for Navy disposal, Navy-generated

hazardous waste listed in 3.5 in accordance with 2.1 and 2.2, as designated by the SUPERVISOR.

Report: Hazardous Waste Manifest Date: + 2

3.1.3 Submit one legible copy, in hard copy or approved

transferrable media, of 2.3 signed by the owner or operator of the disposal facility to the SUPERVISOR within 48 hours of receipt from owner or operator of disposal facility.

3.2 Complete documentation required by 2.1 and 2.2, using EPA or delegated state environmental agency identification number in accordance with 2.4.

3.2.1 Documentation related to hazardous waste generated solely by the physical actions of Ship's Force or Navy employees (termed Navy- Generated Hazardous Waste) on board the vessel shall only bear a generator identification number issued to the Navy pursuant to applicable law. The contractor shall obtain SUPERVISOR'S concurrence with the categorization of the waste as Navy-generated before completion of the manifest. The manifest prepared shall be presented to the SUPERVISOR for completion after the hazardous waste has been identified.

N39040-17-T-0185 Attachment 1 Page 1 of 63

SHIP: YFN 1204 (YFN 1204)

SSP: BOST-517-17 2 of 5 ITEM NO: 077-01-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

3.2.2 Documentation related to hazardous waste generated solely by the physical actions of contractor personnel (termed Contractor- Generated Hazardous Waste) shall bear a generator identification number issued to the contractor pursuant to applicable law.

Regardless of the presence of other material in or on the shipboard systems or structure which may have qualified a waste stream as hazardous, where the contractor performs work on a system or structure using materials (whether or not the use of such materials was specified by the Navy) which by themselves would cause the waste from such work to be a hazardous waste, documentation related to such waste shall only bear a generator number issued to the contractor.

3.2.3 Documentation related to hazardous waste generated by the combined physical actions of Navy and contractor personnel (termed Co-Generated Hazardous Waste) shall bear a generator identification number issued to the contractor pursuant to applicable law and shall also cite in the remarks block a generator identification number issued to the Navy pursuant to applicable law. When the contractor merely drains a system and such drainage creates hazardous waste or the contractor performs work on system or structure using materials which by themselves would not cause the waste from such work to be hazardous waste but such work nonetheless creates a hazardous waste, documentation related to such waste shall bear a generator identification number issued to the contractor and shall also cite in the remarks block a generator identification number issued to the Navy. The contractor shall sign the generator certification on the Uniform Hazardous Waste Manifest whenever use of the manifest is required for disposal. The contractor shall obtain SUPERVISOR's concurrence with the categorization of the wastes as co-generated before completion of the manifest. Manifests prepared shall be presented to the SUPERVISOR for completion after the hazardous waste has been identified.

3.3 If the contractor, while performing work at a Government facility, cannot obtain a separate generator identification number from the state in which the availability will be performed, the contractor shall notify the SUPERVISOR within three business days of receipt of written notification by the state. After obtaining approval of the SUPERVISOR, the contractor shall use the Navy site generator identification number and insert in the remarks block the contractor generator identification number issued for the site where his main facilities are located.

3.4 If, for availabilities at a contractor-owned or controlled facility, the Navy cannot obtain a separate generator identification number for use at a contractor facility, the Navy shall notify the contractor within three business days of receipt of notification by the state. The contractor shall dispose of hazardous waste in accordance with 2.1, 2.2, and 3.2.3.

3.5 Hazardous waste, as identified in 2.1, expected to be produced during performance of this Job Order:

AMOUNT

TYPE NAVY CO-GENERATED CONTRACTOR

Acid Solutions (may include _____ ____________ __________

N39040-17-T-0185 Attachment 1 Page 2 of 63

SSP: BOST-517-17 3 of 5 ITEM NO: 077-01-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

spent sulfamic, citric, chromic, nitric, sulfuric, hydrochloric, etc.)

Ethylene Glycol (Antifreeze) _____ ____________ __________

Sodium Hydroxide _____ ____________ __________

Cleaning Solvents _____ 15 Gallons __________

Sodium Phosphates (Tri, Bi, _____ ____________ __________ or Mono)

Fluorocarbons _____ ____________ __________

Morpholine _____ ____________ __________

Sodium Chromates _____ ____________ __________

Hydrazine _____ ____________ __________

Carbohydrazide _____ ____________ __________

Methyl Ethyl Ketone _____ ____________ __________

Spent Abrasive Blast Material _____ 2 Ton __________

(contaminated with a known hazardous waste)

Trichloroethane _____ 5 Gallon __________

Miscellaneous Chemicals _____ 5 Gallon __________

(Ignitable)

Miscellaneous Chemicals _____ 5 Gallon __________

(Corrosive)

Miscellaneous Chemicals _____ ____________ __________

(TCLP Toxic)

Miscellaneous Chemicals _____ 10 Gallon __________

(Reactive)

Oil (Synthetic) _____ ____________ __________

Paints (Enamel, Latex, _____ 20 Gallon __________

Epoxy, thinners, oil based, rubber paint, nonskid, lacquer, remover, varnishes)

Paints (May include lead, _____ 5 Pounds __________ cadmium, or chrome)

Paint Strippers (phenols, _____ __________ __________ lead, chromium)

N39040-17-T-0185 Attachment 1 Page 3 of 63

SSP: BOST-517-17 4 of 5 ITEM NO: 077-01-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

Asbestos Tile Debris _____ 600 Pounds __________

Wool Felt (contaminated _____ __________ __________ with chromium and PCB's)

Ventilation Debris/Residue

(heavy metals, e.g., cadmium, chromium) _____ ___________

Insulation (May contain lead) _____ 40 Square Feet

Oily Rags _____ 30 Pounds

3.6 Notify the SUPERVISOR at least one working day prior to shipment of hazardous waste for disposal.

Report: Hazardous waste listing Date: + 3

3.7 Submit one legible copy, in hard copy or approved transferrable media, of a report identifying type, amount, and disposal cost of waste listed in 3.5 that was removed during the performance of this Job Order to the SUPERVISOR.

3.7.1 The report shall include analysis or other method used to identify the waste and state whether each listed waste was hazardous (with generator assignment), non-hazardous, or did not exist.

3.7.1.1 Chemical analysis shall be accomplished by laboratories with state or EPA approved quality assurance programs.

3.7.2 The contractor shall make an effort to minimize hazardous waste generation by reducing the volume or toxicity by neutralizing, recycling, or otherwise removing it from the requirements of Subtitle C of 2.1 and include a description of such efforts in the report.

3.8 Nothing contained in this Work Item shall relieve the contractor from complying with applicable federal, state, and local laws, codes, ordinances, and regulations, including the obtaining of licenses and permits in connection with hazardous waste handling and disposal in the performance of this contract.

4. NOTES:

4.1 The waste listed in 3.5 is based on the best information available at the time of preparation of the solicitation. Hazardous waste generated during the actual performance of the work may vary in type or amount from waste listed in 3.5 which may result in renegotiation for credit or increase pursuant to Paragraph (b) of 2.4. The contractor is expected to use best management practice to identify and dispose of all hazardous waste. Some of the substances listed in 3.5 may be neutralized, recycled, or otherwise removed from the requirements of Subtitle C of 2.1. Inclusion of these substances in the waste listed in

3.5 does not preclude the contractor from taking action consistent with

2.1 to reduce or eliminate the hazardous constituents of any waste

6000 Pounds

N39040-17-T-0185 Attachment 1 Page 4 of 63

SSP: BOST-517-17 5 of 5 ITEM NO: 077-01-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

required to be disposed of under the contract in accordance with 2.2.

Processes that add hazardous constituents to the bilges may require that bilge water be disposed of as a hazardous waste.

4.1.1 The types and amounts of wastes listed in 3.5 are estimates of waste to be disposed of under this contract as required by 2.4. They are not estimates of the amount of the work involved in generating that waste. The work requirements of each individual Work Item specify the actual work to be accomplished.

4.2 Hazardous wastes are determined by one or more of the following methods:

4.2.1 Chemical analysis which shows that the material

characteristics of ignitability, corrosivity, reactivity, and/or toxicity (Toxicity Characteristic Leachate Procedure - TCLP) exceed the limits for that material in 40 CFR 261.20 Subpart C.

4.2.2 Reference to a Material Safety Data Sheet (MSDS).

4.2.3 Applying knowledge of the hazardous characteristics of the waste in light of the materials or the process used.

4.3 Asbestos, bilge water, oil/water including sludge, debris and other contaminants, sludge which includes solids and sludge from ballast tanks, CHT tanks, voids, oily waste tanks, fuel ballast tanks, fuel oil tanks, skegs (West coast), PCB's (Maryland), etc., apply only in those states listing them as hazardous waste. When an availability is to be performed in a state where these items are hazardous waste, an estimate of the amount to be generated shall be included in 3.5.

5. GOVERNMENT FURNISHED MATERIAL (GFM):

5.1 LLTM:

1. None.

5.2 PUSH MATERIAL:

1. None.

5.3 KITTED MATERIAL:

1. None.

N39040-17-T-0185 Attachment 1 Page 5 of 63

SHIP: YFN 1204 (YFN 1204) ITEM NO: 110-11-001

COAR: 16 PCN: YFN1-B110

CMP: NONE

PLANNER: ROBERTS, JEARLD

SSP: BOST-517-17 1 of 2 ITEM NO: 110-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

1. SCOPE:

1.1 Title: Underwater Hull Inspection and Repair; accomplish

1.2 Location of Work:

1.2.1 Underwater Hull, Including Skegs, Sides and Stern

1.3 Identification:

1.3.1 Not Applicable

2. REFERENCES:

2.1 Standard Items

2.2 S0103-1300379 Rev A, 500 Ton Open Lighter Outboard Profile, Framing & Structural Details

2.3 T9074-AS-GIB-010/271, Requirements for Nondestructive Testing Methods

3. REQUIREMENTS:

(V)(G) "VISUAL INSPECTION"

3.1 Accomplish a visual inspection within the first 24 hours after drydocking of barge, upon completion of the hydro pressure water wash cleaning of the underwater hull, from the bottom of the keel to the upper boottop limit, including shell plating, sea chests, skegs and structural members for structural integrity, deterioration, pitting, cracks and areas of damage or distortion, using 2.2 for guidance.

Report: Conditions Found Date: + 3

3.1.1 Submit one legible copy, in hard copy or approved

transferrable media, of a report listing conditions found to the

SUPERVISOR.

3.2 Accomplish ultrasonic tests on the underwater hull plating in accordance with 2.3, within 72 hours of drydocking, in 200 locations as designated by the SUPERVISOR, using 2.2 for guidance.

Report: Ultrasonic Test Results and Sketch Date: + 5

3.2.1 Submit one legible copy, in hard copy or approved

transferrable media, of a sketch which includes specific locations with respect to frames, strakes, port or starboard, and existing welded butts and seams to the SUPERVISOR.

3.2.1.1 Sketch shall show location of each reading, original

material thickness, existing material thickness, and percentage of material thickness reduction.

N39040-17-T-0185 Attachment 1 Page 6 of 63

SSP: BOST-517-17 2 of 2 ITEM NO: 110-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

3.2.1.2 Notate if reading is taken over existing doubler plate.

3.3 Accomplish the following repairs as determined by the visual inspection in 3.1 and ultrasonic testing results of 3.2 in locations as designated by the SUPERVISOR.

3.3.1 Vee-out and weld a total of 100 linear feet of splits, cracks, deteriorated and damaged welds.

3.3.2 Clad weld a total of 500 square inches of plating defects.

3.3.2.1 Surfaces shall be ground to smooth metal prior to

welding.

3.3.2.2 Fill local pits and grooves with weld metal prior to the application of principal build-up layers.

3.3.3 Install new a total of 200 square feet of 15.3 pound steel doubler plates conforming to MIL-S-22698.

3.3.3.1 Install new steel doubler plates with plug welds slots spaced at 18 inch centers. Seal weld all edges of plates with 3/8 inch fillet welds.

3.3.3.2 Locate plug welds on doubler plates to align with backup structure.

3.3.4 Accomplish the requirements of 009-12 of 2.1, including Table 3, Column A, Lines One through 7.

3.3.5 Accomplish the requirements of 009-25 of 2.1, for the local air hose test of the repaired weld seams and new hull plating.

Allowable leakage: None.

3.4 Accomplish the requirements of 009-32 of 2.1, for new and disturbed surfaces.

4. NOTES:

4.1 None.

5. GOVERNMENT FURNISHED MATERIAL (GFM):

5.1 LLTM:

1. None.

5.2 PUSH MATERIAL:

1. None.

5.3 KITTED MATERIAL:

N39040-17-T-0185 Attachment 1 Page 7 of 63

SHIP: YFN 1204 (YFN 1204) ITEM NO: 123-21-001

COAR: 16 PCN: YFN1-L002

YFN1-B123

YFN1-B124

CMP: NONE

PLANNER: ROBERTS, JEARLD

SSP: BOST-517-17 1 of 2 ITEM NO: 123-21-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

1. SCOPE:

1.1 Title: Void; clean, inspect, and preserve

1.2 Location of Work:

1.2.1 Throughout the Craft

1.3 Identification:

1.3.1 Quantity (6 EA), Void, Nos. One through 6 (including Quantity (11 EA), associated raised bolted access cover and Quantity (One EA), flush bolted access cover)

2. REFERENCES:

2.1 Standard Items

2.2 YFN 1204-SK-002 Rev -, YFN 1204 Arrangement Modifications Incid Barge Upgrade

3. REQUIREMENTS:

(V)(G) "VOID INSPECTION"

3.1 Accomplish a joint visual inspection with the SUPERVISOR of each void listed in 1.3 and located in 1.2 for existing preservation coating, structural integrity, deterioration, pitting, cracks, and areas of damage or distortion including structural members, manhole covers and associated coamings.

Report: Inspection Results Date: + 3

3.1.1 Submit one legible copy, in hard copy or approved

transferrable media, of a report listing type, extent, and location of defects to the SUPERVISOR.

3.1.2 Accomplish the requirements of 009-25 of 2.1 for preliminary air test of each void. Test pressure shall be 2 PSIG.

3.2 Accomplish the following repairs to each void listed in 1.3 and located in 1.2, using 2.2 for guidance:

3.2.1 Vee-out and weld repair 10 linear feet of deteriorated and damaged welds as designated by the SUPERVISOR.

3.2.2 Accomplish the requirements of 009-12 of 2.1, including Table 3, Column A, Lines One through 7.

3.2.2.1 Accomplish nondestructive testing in accordance with

Line 11.

3.3 Accomplish the requirements of 009-32 of 2.1, including Table 4, Line 15 or 15A for a total of 500 square feet of void surfaces listed in

N39040-17-T-0185 Attachment 1 Page 8 of 63

SSP: BOST-517-17 2 of 2 ITEM NO: 123-21-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

1.3 and located in 1.2, including interior surfaces of access covers as designated by the SUPERVISOR.

3.3.1 Topcoat color shall match existing.

3.3.2 Accomplish the requirements of Paragraph 3.1.6 of 009-32 for surface preparation in lieu of abrasive blasting.

3.4 Accomplish the requirements of 009-32 of 2.1, including Table 2, Line One or 2, for exterior surfaces of each void access cover listed in 1.3.1, including associated coaming.

3.5 Accomplish the requirements of 009-25 of 2.1 for air test of each void listed in 1.3 and located in 1.2. Test pressure shall be 2 PSIG.

Maintain test pressure for 15 minutes for temperature stabilization prior to start of test. Hold test pressure for 10 minutes. Allowable drop in pressure: None.

3.6 Accomplish the requirements of 009-32 of 2.1 for new and disturbed surfaces.

4. NOTES:

4.1 The possibility of lead based paint exist in interior surfaces of voids listed in 1.3. Contractor shall take safety precautions as required by Paragraphs 3.1.1 and 3.1.2 of 009-32.

4.2 Voids listed in 1.3 are opened and closed in Work Item 992-31-001, Cleaning and Pumping; accomplish.

5. GOVERNMENT FURNISHED MATERIAL(GFM):

5.1 LLTM:

1. None.

5.2 PUSH MATERIAL:

1. None.

5.3 KITTED MATERIAL:

N39040-17-T-0185 Attachment 1 Page 9 of 63

SHIP: YFN 1204 (YFN 1204) ITEM NO: 150-11-001

COAR: 16 PCN: YFN1-B150

CMP: NONE

PLANNER: ROBERTS, JEARLD

SSP: BOST-517-17 1 of 1 ITEM NO: 150-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

1. SCOPE:

1.1 Title: Exterior Attachment; remove

1.2 Location of Work:

1.2.1 Superstructure, Frames 5 and 51, Port and Starboard

1.3 Identification:

1.3.1 Quantity (30 EA), Exterior Attachment (pad eyes, hooks, brackets, etc.)

2. REFERENCES:

2.1 Standard Items

3. REQUIREMENTS:

3.1 Remove existing equipment listed in 1.3 and located in 1.2 as designated by the SUPERVISOR.

3.1.1 Chip and grind surfaces flush and smooth in way of removals.

3.2 Accomplish the requirements of 009-32 of 2.1 for new and disturbed surfaces.

4. NOTES:

4.1 None.

5. GOVERNMENT FURNISHED MATERIAL (GFM):

5.1 LLTM:

1. None.

5.2 PUSH MATERIAL:

1. None.

5.3 KITTED MATERIAL:

N39040-17-T-0185 Attachment 1 Page 10 of 63

SHIP: YFN 1204 (YFN 1204) ITEM NO: 167-11-001

COAR: 16 PCN: YFN1-B169

YFN1-B623

CMP: NONE

PLANNER: ROBERTS, JEARLD

SSP: BOST-517-17 1 of 2 ITEM NO: 167-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

1. SCOPE:

1.1 Title: Watertight Hatch and Inclined Ladder; install

1.2 Location of Work:

1.2.1 Main Deck, Office Number One, Frames 36-39, Port

1.3 Identification:

1.3.1 Quantity (One EA), Hatch WT Raised, 36 Inch by 60 Inch, Individually Dogged, 12 Dog, Short Side Hinged, Steel w/o Scuttle

1.3.2 Quantity (One EA), 60 Degree, 30 inch wide, Inclined Ladder

2. REFERENCES:

2.1 Standard Items

2.2 YFN 1204-SK-004 Rev -, YFN 1204 Hatch Installation Barge Upgrade

2.3 YFN 1204-SK-002 Rev -, YFN 1204 Arrangement Modifications Incid Barge Upgrade

2.4 YFN 1204-SK-006 Rev -, YFN 1204 Store Room #1 Installation Barge Upgrade

2.5 805-1624079, Hatch W. T. Raised, Indv Dogged, 36 X 60, W/O Scuttle

2.6 805-1624072, Hatch W.T. Raised, Indv Dogged, Misc Details

2.7 805-1624071, Hatch W.T. Raised, Indv Dogged, Dog Hinge and Misc Det.

2.8 804-860039, Inclined Ladder, Steel, Assemblies and Details

2.9 804-860041, Inclined Ladder, Aluminum and Steel Tread Details

3. REQUIREMENTS:

3.1 Install new hatch and inclined ladder listed in 1.3 in location listed in 1.2 in accordance with 2.2, using 2.3 through 2.9 for guidance.

3.1.1 Accomplish the requirements of 009-12 of 2.1, including Table 3, Column A, Lines One through 7.

3.1.2 Accomplish the requirements of 009-32 of 2.1, including Table 3, Line One, for new hatch and deck coaming.

3.2 Adjust the dogs, hinges, and wedges for positive dogging action.

3.3 Accomplish the requirements of 009-25 of 2.1 for a chalk test of the new hatch installed in 3.1.

3.4 Accomplish the requirements of 009-25 of 2.1 for the air hose test of the new hatch installed in 3.1. Allowable leakage: None.

3.5 Accomplish the requirements of 009-32 of 2.1 for new and disturbed surfaces.

4. NOTES:

N39040-17-T-0185 Attachment 1 Page 11 of 63

SSP: BOST-517-17 2 of 2 ITEM NO: 167-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

4.1 None.

5. GOVERNMENT FURNISHED MATERIAL(GFM):

5.1 LLTM:

1. None.

5.2 PUSH MATERIAL:

1. None.

5.3 KITTED MATERIAL:

N39040-17-T-0185 Attachment 1 Page 12 of 63

SHIP: YFN 1204 (YFN 1204) ITEM NO: 167-11-002

COAR: 16 PCN: YFN1-B167

CMP: NONE

PLANNER: ROBERTS, JEARLD

SSP: BOST-517-17 1 of 2 ITEM NO: 167-11-002

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

1. SCOPE:

1.1 Title: Exterior Door; replace

1.2 Location of Work:

1.2.1 Vestibule, Main Deck Starboard, Frame 5

1.2.2 Main Deck, Starboard, Frame 41

1.2.3 Main Deck, Port, Frame 25

1.3 Identification:

1.3.1 Quantity (3 EA), Weathertight Door, 36 inches X 66 inches, RH (Inward Swing), 9 inch sill, Passage Set with Lever Handle, Freeman Marine Equipment Series 1111 (w/o Window), Item No. One of 2.2

2. REFERENCES:

2.1 Standard Items

2.2 YFN 1204-SK-002 Rev -, YFN 1204 Arrangement Modifications Incid Barge Upgrade

3. REQUIREMENTS:

3.1 Remove existing and install new doors, with door water shed for the equipment listed in 1.3 in location listed in 1.2 in accordance with 2.2.

3.1.1 Insert bulkhead removal area with new plating same thickness and type as existing to receive each new door.

3.1.2 Accomplish the requirements of 009-12 of 2.1, including Table 3, Column A, Lines One through 7.

3.1.3 Match drill new doors and bulkhead receiving doors using 2.2 for guidance.

3.2 Accomplish the requirements of 009-25 of 2.1 for a water (exterior) hose test of each door installed in 3.1, using Note 23 of 2.2 for guidance. Allowable leakage: None.

3.3 Accomplish the requirements of 009-11 of 2.1.

(V)(G) "OPERATIONAL TEST"

3.4 Accomplish an operational test of each new door installed in 3.1 for opening and closing with no binding and ease of operation.

3.5 Accomplish the requirements of 009-32 of 2.1 for new and disturbed surfaces.

4. NOTES:

4.1 Known source for doors listed in 1.3 as follows:

Freeman Marine Equipment Inc.

28336 Hunter Creek Road

N39040-17-T-0185 Attachment 1 Page 13 of 63

SSP: BOST-517-17 2 of 2 ITEM NO: 167-11-002

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

Gold Beach, OR 97444

POC: Jason Setzer

Ph: (888)373-3626 ext. 109

FAX: (541)247-2114

5. GOVERNMENT FURNISHED MATERIAL(GFM):

5.1 LLTM:

1. None.

5.2 PUSH MATERIAL:

1. None.

5.3 KITTED MATERIAL:

N39040-17-T-0185 Attachment 1 Page 14 of 63

SHIP: YFN 1204 (YFN 1204) ITEM NO: 332-11-001

COAR: 16 PCN: YFN1-B332

CSWT FILE NO: 332-001 CMP: NONE

REVISED: 16 Dec 2015 PLANNER: ROBERTS, JEARLD

SSP: BOST-517-17 1 of 2 ITEM NO: 332-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

1. SCOPE:

1.1 Title: Interior Overhead Lighting Modification and Installation;

accomplish

1.2 Location of Work:

1.2.1 Main Deck, Interior

1.2.2 Hold, Interior

1.3 Identification:

1.3.1 Not Applicable

2. REFERENCES:

2.1 Standard Items

2.2 YFN 1204-SK-007, Miscellaneous Lighting Mods Barge Upgrade

2.3 MIL-STD-2003, Electric Plant Installation Standard Methods for Surface Ships and Submarines

2.4 MIL-STD-1310, Shipboard Bonding, Grounding, and Other Techniques for Electromagnetic Compatibility and Safety

3. REQUIREMENTS:

3.1 Accomplish the requirements of 2.2 for interior lighting

modifications and installation in locations listed in 1.2.

3.1.1 Accomplish the requirements of 009-12 of 2.1, including Table 3, Column A, Lines One through 7.

3.1.2 Electrical installations shall be in accordance with 2.3.

3.1.3 Bond and ground equipment in accordance with 2.4.

(V)(G) "OPERATIONAL TEST"

3.2 Accomplish an operational test of newly installed equipment.

3.2.1 Energize and de-energize lights using associated light

switches. Ensure lights illuminate in the "ON" position and extinguish in the "OFF" position. Return switches to the "ON" position when test is completed.

3.3 Accomplish the requirements of 009-32 of 2.1 for new and disturbed surfaces.

4. NOTES:

4.1 None.

5. GOVERNMENT FURNISHED MATERIAL (GFM):

5.1 LLTM:

N39040-17-T-0185 Attachment 1 Page 15 of 63

SSP: BOST-517-17 2 of 2 ITEM NO: 332-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

5.2 PUSH MATERIAL:

1. None.

5.3 KITTED MATERIAL:

N39040-17-T-0185 Attachment 1 Page 16 of 63

SHIP: YFN 1204 (YFN 1204) ITEM NO: 409-11-001

COAR: 16 PCN: YFN1-B492

CMP: NONE

PLANNER: ROBERTS, JEARLD

SSP: BOST-517-17 1 of 2 ITEM NO: 409-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

1. SCOPE:

1.1 Title: Local Area Network (LAN) Remove, Modify and Install;

accomplish

1.2 Location of Work:

1.2.1 Throughout the Barge

1.3 Identification:

1.3.1 Not Applicable

2. REFERENCES:

2.1 Standard Items

2.2 YFN 1204-SK-009 Rev -, YFN 1204 LAN/Telephone Mods Barge Upgrade

2.3 MIL-STD-2003, Electric Plant Installation Standard Methods for Surface Ships and Submarines

2.4 MIL-STD-1310, Shipboard Bonding, Grounding, and Other Techniques for Electromagnetic Compatibility and Safety

3. REQUIREMENTS:

3.1 Accomplish removals, modifications and new installations of the Barge NMCI (NNPI), Legacy Local Area Network (LAN) systems in location listed in 1.2 in accordance with 2.2 and 2.3 as follows:

3.1.1 The existing Barge NMCI (NNPI) LAN System drop boxes and associated drop box cabling shall be disconnected and removed back to the existing NMCI server cabinet. Retain the NMCI server cabinet at existing location.

3.1.2 The existing Barge Legacy LAN System shall be removed in its entirety to include all cabling and associated equipment.

3.1.3 Install new connectors at cable termination points.

3.1.4 Install electrical cables in accordance with 2.3.

3.1.5 Bond and ground equipment in accordance with 2.4.

3.2 Test each cable conductor and associated connector for continuity and complete circuit in accordance with 2.3. Ensure terminal connections are tight.

Report: Results of Electrical Test Date: + 3

3.2.1 Submit one legible copy, in hard copy or electronic media, of a report listing results of the requirements of 3.2, including circuit number, lead numbers, and readings obtained, to the SUPERVISOR within 48 hours of completion of tests.

3.3 Accomplish the requirements of 009-32 of 2.1 for new and disturbed surfaces.

N39040-17-T-0185 Attachment 1 Page 17 of 63

SSP: BOST-517-17 2 of 2 ITEM NO: 409-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

4. NOTES:

4.1 None.

5. GOVERNMENT FURNISHED MATERIAL (GFM):

5.1 LLTM:

1. None.

5.2 PUSH MATERIAL:

1. None.

5.3 KITTED MATERIAL:

N39040-17-T-0185 Attachment 1 Page 18 of 63

SHIP: YFN 1204 (YFN 1204) ITEM NO: 4223113001

-OAC: 1R P-N: YFN136BB0

-MP: NONE

PWANNEC: CO6ECTSL VEACWD

SSP: 6OST3e1c31c 1 5, 2 ITEM NO: 4223113001

EJPOCT -ONTCOWWED DATA: T7of X5hisdum h5umnouf mdh7uohnt ou,5asnmo5u l75fd drw5am of x5pdaudX gv bySy Iumdaunmo5unt Tan,,oh ou Aasf Cdxitnmo5u (ITAC)y T7of ou,5asnmo5u sifm u5m gd manuf,daadX m5 n ,5adoxu wdaf5uUdumomv lom75im wa5wda nim75ao.nmo5u 5, m7d bySy /5pdausdumy zo5tnmo5uf snv adfitm ou nXsouofmanmopdL hopotL 5a haosount wduntmodfy

1y S-OPE:

1y1 Tomtd: Ermdao5a Wox7moux M5Xo,ohnmo5u nuX Iufmnttnmo5uG nhh5swtof7

1y2 W5hnmo5u 5, ;5ak:

1y2y1 Ermdao5a ;dnm7da DdhkfL P5am nuX Smnag5naX

1yB IXdumo,ohnmo5u:

1yBy1 N5m Awwtohngtd

2y CEFECEN-ES:

2y1 SmnuXnaX Imdsf

2y2 YFN 12043SK300cL Mofhdttnud5if Wox7moux M5Xf 6naxd bwxanXd

2yB MIW3STD3200BL Etdhmaoh Ptnum Iufmnttnmo5u SmnuXnaX Mdm75Xf ,5a Sia,nhd S7owf nuX Sigsnaoudf

2y4 MIW3STD31B10L S7owg5naX 65uXouxL /a5iuXouxL nuX Om7da Tdh7uoqidf ,5a Etdhma5snxudmoh -5swnmogotomv nuX Sn,dmv

By CEQbICEMENTS:

By1 Ahh5swtof7 m7d adqioadsdumf 5, 2y2 ,5a drmdao5a tox7moux s5Xo,ohnmo5uf nuX oufmnttnmo5u ou t5hnmo5uf tofmdX ou 1y2y

By1y1 Etdhmaohnt oufmnttnmo5uf f7ntt gd ou nhh5aXnuhd lom7 2yBy

By1y2 65uX nuX xa5iuX dqiowsdum ou nhh5aXnuhd lom7 2y4y

By1yB Cds5pd iuifdX ,5iuXnmo5ufL hngtd 7nuxdafL loadlnvfL ganhkdmfL h5uma5t flomh7dfL nuX fmiXfy -7ow nuX xaouX fia,nhdf ,tif7 nuX fs55m7 ou lnv 5, ads5pntfy

By1y4 Cds5pd drofmoux fmi,,oux migdf nuX wnmh7 lom7 wtnmoux 5, fnsd mvwd nuX m7ohkudff 5, fiaa5iuXoux wtnmoux ou lnv 5, ads5pntfy

By1ye Ahh5swtof7 m7d adqioadsdumf 5, 009312 5, 2y1L ouhtiXoux Tngtd BL -5tisu AL Woudf Oud m7a5ix7 cy

By1yR Ahh5swtof7 m7d adqioadsdumf 5, 00932e 5, 2y1 ,5a nu noa 75fdL lnmda 75fdL 5a pnhiis g5r mdfm 5, dnh7 wnmh7dX nadny Att5lngtd tdnknxd: N5udy

(z)(/) "OPECATIONAW TEST"

By2 Ahh5swtof7 nu 5wdanmo5unt mdfm 5, udltv oufmnttdX dqiowsdum ou By1y

By2y1 Eudaxo.d nuX Xd3dudaxo.d tox7mf ifoux nff5honmdX tox7m flomh7dfy Eufiad tox7mf ottisounmd ou m7d "ON" w5fomo5u nuX drmouxiof7 ou m7d "OFF" w5fomo5uy Cdmiau flomh7df m5 m7d "ON" w5fomo5u l7du mdfm of h5swtdmdXy

ByB Ahh5swtof7 m7d adqioadsdumf 5, 0093B2 5, 2y1 ,5a udl nuX XofmiagdX fia,nhdfy

N39040-17-T-0185 Attachment 1 Page 19 of 63

SSP: 6OST3e1c31c 2 5, 2 ITEM NO: 4223113001

EJPOCT -ONTCOWWED DATA: T7of X5hisdum h5umnouf mdh7uohnt ou,5asnmo5u l75fd drw5am of x5pdaudX gv bySy Iumdaunmo5unt Tan,,oh ou Aasf Cdxitnmo5u (ITAC)y T7of ou,5asnmo5u sifm u5m gd manuf,daadX m5 n ,5adoxu wdaf5uUdumomv lom75im wa5wda nim75ao.nmo5u 5, m7d bySy /5pdausdumy zo5tnmo5uf snv adfitm ou nXsouofmanmopdL hopotL 5a haosount wduntmodfy

4y NOTES:

4y1 N5udy ey /OzECNMENT FbCNISHED MATECIAW (/FM):

ey1 WWTM:

1y N5udy ey2 PbSH MATECIAW:

1y N5udy eyB KITTED MATECIAW:

1y N5udy

N39040-17-T-0185 Attachment 1 Page 20 of 63

SHIP: YFN 1204 (YFN 1204) ITEM NO: 432-11-001

COAR: 16 PCN: YFN1-B432

CMP: NONE

PLANNER: ROBERTS, JEARLD

DEMERS, RAY

SSP: BOST-517-17 1 of 2 ITEM NO: 432-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

1. SCOPE:

1.1 Title: Telephone System CKT "J", Remove and Install; accomplish

1.2 Location of Work:

1.2.1 Throughtout the Vessel

1.3 Identification:

1.3.1 Not Applicable

2. REFERENCES:

2.1 Standard Items

2.2 YFN 1204-SK-009 Rev -, YFN 1204 LAN/Telephone Mods Barge Upgrade

2.3 MIL-STD-2003, Electric Plant Installation Standard Methods for Surface Ships and Submarines

2.4 MIL-STD-1310, Shipboard Bonding, Grounding and Other Techniques for Electromagnetic Compatibility and Safety

3. REQUIREMENTS:

3.1 Remove existing barge telephone system in its entirety to include all cabling and associated equipment in location listed in 1.2.

3.2 Accomplish the installation of the Dial Telephone System CKT "J" and associated cabling and equipment in location listed in 1.2, in accordance with 2.2 and 2.3.

3.2.1 Bond and ground equipment in accordance with 2.4.

3.2.2 Accomplish the requirements of 009-12 of 2.1, including Table 3, Column A, Lines One through 7.

3.2.3 Template installation to suit existing barge conditions.

(V)(G) "OPERATIONAL TEST"

3.3 Accomplish an operational test of the Dial Telephone System CKT "J" installed in 3.2, using 2.2 and manufacturer's operation manual for guidance.

Report: Operational Test Results Date: + 3

3.3.1 Submit one legible copy, in hard copy or approved

transferrable media, of a report listing results of the requirements of 3.3 to the SUPERVISOR.

3.3.2 Call to and from each telephone to verify proper transmission and receiving from each telephone set.

3.4 Accomplish the requirements of 009-32 of 2.1 for new and disturbed

N39040-17-T-0185 Attachment 1 Page 21 of 63

SSP: BOST-517-17 2 of 2 ITEM NO: 432-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

surfaces to match surrounding areas.

4. NOTES:

4.1 None.

5. GOVERNMENT FURNISHED MATERIAL (GFM):

5.1 LLTM:

1. None.

5.2 PUSH MATERIAL:

1. None.

5.3 KITTED MATERIAL:

N39040-17-T-0185 Attachment 1 Page 22 of 63

SHIP: YFN 1204 (YFN 1204) ITEM NO: 511-11-001

COAR: 16 PCN: YFN1-B513

CMP: NONE

PLANNER: ROBERTS, JEARLD

DEMERS, RAY

SSP: BOST-517-17 1 of 2 ITEM NO: 511-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

1. SCOPE:

1.1 Title: Unit Heater; install

1.2 Location of Work:

1.2.1 Hold, Frames 36-45, Port and Starboard

1.3 Identification:

1.3.1 Quantity (One EA), Electric Unit Heater (2-38-1), 480 VAC, 3 Phase, 7.5 KW, Item No. One of 2.2 (Similar or equal to Dayton Model No. 2YU67)

1.3.2 Quantity (One EA), Electric Unit Heater (2-39-2), 480 VAC, 3 Phase, 7.5 KW, Item No. One of 2.2 (Similar or equal to Dayton Model No. 2YU67)

2. REFERENCES:

2.1 Standard Items

2.2 YFN 1204-SK-013 Rev -, YFN 1204 HVAC Mods Hold

2.3 YFN 1204-SK-008 Rev -, YFN 1204 Miscellaneous Power Mods Barge Upgrade

2.4 MIL-STD-2003, Electric Plant Installation Standard Methods for Surface Ships and Submarines

2.5 MIL-STD-1310, Shipboard Bonding, Grounding, and Other Techniques for Electromagnetic Compatibility and Safety

3. REQUIREMENTS:

3.1 Accomplish the requirements of 2.2 and 2.3 for installation of the equipment listed in 1.3 and associated controls in locations listed in 1.2.

3.1.1 Electrical installations shall be in accordance with 2.4.

3.1.2 Bond and ground equipment in accordance with 2.5.

3.1.3 Install new label plates in accordance with 2.3.

(V)(G) "OPERATIONAL TEST"

3.2 Accomplish an operational test of the equipment installed in 3.1 in accordance with 2.3 and manufacture's instructions.

3.3 Accomplish the requirements of 009-32 of 2.1 for new and disturbed surfaces.

4. NOTES:

4.1 None

5. GOVERNMENT FURNISHED MATERIAL (GFM):

N39040-17-T-0185 Attachment 1 Page 23 of 63

SSP: BOST-517-17 2 of 2 ITEM NO: 511-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

5.1 LLTM:

1. None.

5.2 PUSH MATERIAL:

1. None.

5.3 KITTED MATERIAL:

N39040-17-T-0185 Attachment 1 Page 24 of 63

SHIP: YFN 1204 (YFN 1204) ITEM NO: 512-11-001

COAR: 16 PCN: YFN1-B512

CMP: NONE

PLANNER: ROBERTS, JEARLD

SSP: BOST-517-17 1 of 2 ITEM NO: 512-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

1. SCOPE:

1.1 Title: Rooftop Fan; remove (OPTION ITEM)

1.2 Location of Work:

1.2.1 Top of Superstructure; Frames 13 Port, 28 Starboard, and 44 Port and Starboard

1.3 Identification:

1.3.1 Quantity (4 EA), Rooftop Fan

2. REFERENCES:

2.1 Standard Items

2.2 YFN 1204-SK-001 Rev -, YFN 1204 Misc Removals Incid Barge Upgrade

2.3 YFN 1204-SK-010 Rev -, YFN 1204 HVAC Modifications

2.4 MIL-STD-2003, Electric Plant Installation Standard Methods for Surface Ships and Submarines

3. REQUIREMENTS:

3.1 Remove the equipment listed in 1.3 and located in 1.2 using 2.2 and

2.3 for guidance. Electrically secure and disconnect cable and pull back from nearest termination point, through existing conduit and stuffing tube in accordance with 2.4.

3.1.1 Remove unused foundations, cable hangers, wireways, brackets, control switches, and studs that are below the suspended ceiling tiles. Chip and grind surfaces flush and smooth in way of removals.

3.1.2 Install new roof plating similar to existing in way removals.

3.1.3 Accomplish the requirements of 009-12 of 2.1, including Table 4, Column A, Lines One through 7.

3.1.4 Accomplish the requirements of 009-25 of 2.1 for an air hose, water hose, or vacuum box test of each patched area. Allowable leakage: None.

3.2 Accomplish the requirements of 009-32 of 2.1 for new and disturbed surfaces.

4. NOTES:

4.1 None.

5. GOVERNMENT FURNISHED MATERIAL (GFM):

5.1 LLTM:

1. None.

5.2 PUSH MATERIAL:

N39040-17-T-0185 Attachment 1 Page 25 of 63

SSP: BOST-517-17 2 of 2 ITEM NO: 512-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

5.3 KITTED MATERIAL:

N39040-17-T-0185 Attachment 1 Page 26 of 63

SHIP: YFN 1204 (YFN 1204) ITEM NO: 512-90-001

COAR: 16 PCN: YFN1-B511

CMP: NONE

PLANNER: ROBERTS, JEARLD

SSP: BOST-517-17 1 of 2 ITEM NO: 512-90-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

1. SCOPE:

1.1 Title: HVAC Mod Split System; install (OPTION ITEM)

1.2 Location of Work:

1.2.1 House Top

1.2.2 Main Deck

1.3 Identification:

1.3.1 Not Applicable

2. REFERENCES:

2.1 Standard Items

2.2 YFN 1204-SK-010 Rev -, YFN 1204 HVAC Modifications

2.3 YFN 1204-SK-011 Rev -, YFN 1204 Piping Installation A/C System

2.4 YFN 1204-SK-012 Rev -, YFN 1204 HVAC Installation A/C Piping Installation

2.5 YFN 1204-SK-014 Rev -, YFN 1204 HVAC System Instl Drain Piping

2.6 YFN 1204-SK-005 Rev -, YFN 1204 Foundation Incidental HVAC Install

2.7 YFN 1204-SK-008 Rev -, YFN 1204 Miscellaneous Power Mods Barge Upgrade

2.8 YFN 1204-SK-002 Rev -, YFN 1204 Arrangement Modifications Incid Barge Upgrade

2.9 S9086-RW-STM-010/CH 516, Refrigeration Systems

2.10 113-5377425, MTG Requirements Small Equip in Shock Critical Areas

2.11 101-5317400, Strl Penetrations in Surface Ships

2.12 605-1874109, Label Plate Types

3. REQUIREMENTS:

3.1 Accomplish the requirements of 2.2 through 2.8, using 2.9 through

2.12 for guidance.

3.1.1 Accomplish the requirements of 009-12 of 2.1, including Table 3, Columns A and C, lines One through 7.

3.1.2 Accomplish the requirements of 009-12 of 2.1, including Table One, Columns A and B, Lines One through 10.

3.1.3 Accomplish the requirements of 009-25 of 2.1 for an air hose, water hose or vacuum box test of watertight boundaries affected by work in this Work Item. Allowable leakage: None.

(V)(G) "CLEANLINESS"

3.1.4 Accomplish the requirements of 009-107 of 2.1 and Cleaning

N39040-17-T-0185 Attachment 1 Page 27 of 63

SSP: BOST-517-17 2 of 2 ITEM NO: 512-90-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

Notes C-1 and C-2 of 2.4, using system fluids.

3.1.4.1 General Cleaning shall be Level II.

(V)(G) "AIR TEST, EVACUATION AND CHARGING"

3.1.5 Accomplish testing in accordance with Test Notes 1, 2 and 3 of 2.4.

3.1.5.1 Accomplish the requirements of 009-71 of 2.1 for new and disturbed piping systems, using nitrogen at 602 PSIG. Allowable leakage: None.

3.1.6 Accomplish the requirements of 009-11 of 2.1.

3.1.7 Fabricate and install label plates, cable tags and conductor identification markers in accordance with 2.3 through 2.7, using 2.12 for guidance.

(V)(G) "OPERATIONAL TEST"

3.2 Accomplish an operational test of the HVAC equipment and controls to ensure equipment functions to design sequence of operation in accordance with manufacturer's instructions.

3.3 Accomplish the requirements of 009-32 of 2.1 for new and disturbed surfaces.

4. NOTES:

4.1 Known source for Mitsubishi technical representatives are:

Dry Air Systems

62 Forest Ridge Drive

Rowley, MA. 01969

PH: (603)425-7700

info@das4hvac.com http://www.dryairsystemsinc.com/

5. GOVERNMENT FURNISHED MATERIAL(GFM):

5.1 LLTM:

1. None.

5.2 PUSH MATERIAL:

1. None.

5.3 KITTED MATERIAL:

N39040-17-T-0185 Attachment 1 Page 28 of 63

SHIP: YFN 1204 (YFN 1204) ITEM NO: 514-11-001

COAR: 16 PCN: YFN1-B514

CSWT FILE NO: 514-001 CMP: NONE

REVISED: 16 Dec 2015 PLANNER: ROBERTS, JEARLD

SSP: BOST-517-17 1 of 2 ITEM NO: 514-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

1. SCOPE:

1.1 Title: Air Conditioning Unit; install (OPTION ITEM)

1.2 Location of Work:

1.2.1 Barge Deck House

1.3 Identification:

1.3.1 Quantity (6 EA), Air Conditioning (AC) Unit, 15,000 BTU, 12 amps, 115 volt, 60 Hz, Item No. One of 2.2 (Similar or equal to LG Model LW1513ER)

2. REFERENCES:

2.1 Standard Items

2.2 YFN 1204-SK-010 Rev -, YFN 1204 HVAC Modifications

3. REQUIREMENTS:

3.1 Remove existing and install new the equipment listed in 1.3 and located in 1.2, in accordance with 2.2.

3.1.1 Install new angle iron 2 Inch x 2 Inch x 1/4 Inch support foundation and braces capable of supporting the weight of each AC Unit.

3.1.1.1 Accomplish the requirements of 009-12 of 2.1, including Table 3, Column A, Lines One through 7.

3.1.2 Seal exterior opening to ensure AC units are snug in access cuts. Allowable gaps between each unit and adjacent bulkhead: None.

3.1.2.1 Accomplish the requirements of 009-25 of 2.1 for a air hose test of sealing surface. Allowable leakage: None.

(V)(G) "OPERATIONAL TEST"

3.2 Energize and test each AC unit installed in 3.1. Ensure each AC unit functions in accordance with manufacturer's specifications and designed sequence of operation.

3.3 Accomplish the requirements of 009-32 of 2.2 for new and disturbed surfaces.

4. NOTES:

4.1 None.

5. GOVERNMENT FURNISHED MATERIAL(GFM):

5.1 LLTM:

1. None.

5.2 PUSH MATERIAL:

N39040-17-T-0185 Attachment 1 Page 29 of 63

SSP: BOST-517-17 2 of 2 ITEM NO: 514-11-001

EXPORT CONTROLLED DATA: This document contains technical information whose export is governed by U.S.

International Traffic in Arms Regulation (ITAR). This information must not be transferred to a foreign person/entity without proper authorization of the U.S. Government. Violations may result in administrative, civil, or criminal penalties.

1. None.

5.3 KITTED MATERIAL:

N39040-17-T-0185 Attachment 1 Page 30 of 63

SHIP: YFN 1204 (YFN 1204) ITEM NO: 607-11-001

COAR: 16 PCN: YFN1-B691

CMP: NONE

P3ANNER: ROBERTSL ,EAR3J

JEMERSL RAY

SSP: BOST-D19-19 1 5o 2 ITEM NO: 607-11-001

EfPORT CONTRO33EJ JATA: TXhi s5dcumen d5enthei nmdXehdta heo5lutnh5e rX5im mwx5ln hi p5gmlems vb yUSU Ienmletnh5eta Tltoohd he Alui Rmpcatnh5e (ITAR)U TXhi heo5lutnh5e ucin e5n vm nlteiomllms n5 t o5lmhpe xmli5e.menhnb rhnX5cn xl5xml tcnX5lh/tnh5e 5o nXm yUSU z5gmleumenU Gh5atnh5ei utb lmican he tsuhehinltnhgmL dhghaL 5l dlhuheta xmetanhmiU

1U SCOPE:

1U1 Thnam: Sn5lml55u AlltepmumenV tdd5uxahiX

1U2 35dtnh5e 5o W5l;:

1U2U1 H5asL Fltumi k6-4DL P5ln tes Sntlv5tls

1Uk Ismenhohdtnh5e:

1UkU1 N5n Axxahdtvam

2U REFERENCES:

2U1 Sntestls Inmui

2U2 YFN 1204-SQ-006 Rmg -L YFN 1204 Sn5lm R55u K1 Ieintaatnh5e Btlpm yxpltsm

2Uk YFN 1204-SQ-002 Rmg -L YFN 1204 Alltepmumen M5shohdtnh5ei Iedhs Btlpm yxpltsm

2U4 YFN 1204-SQ-007 Rmg -L YFN 1204 Mhidmaatem5ci P5rml M5si Btlpm yxpltsm

2UD YFN 1204-SQ-009 Rmg -L YFN 1204 Mhidmaatem5ci 3hpXnhep M5si Btlpm yxpltsm

2U6 YFN 1204-SQ-004 Rmg -L YFN 1204 HtndX Ieintaatnh5e Btlpm yxpltsm

2U9 Skk06-#21990L Cahxi tes Scv-vtimi o5l Mmnta Fclehnclm kU RE8yIREMENTS:

kU1 Add5uxahiX nXm lmqchlmumeni 5o 2U2 tes 2Uk he a5dtnh5ei ahinms he 1U2L cihep 2U4 nXl5cpX 2U6 o5l pchstedm o5l emr in5lm l55u u5shohdtnh5eiU kU1U1 Rmu5gm k0 ahemtl ommn 5o tvtes5ems inmma xhxhepL ohnnhepiL tes tii5dhtnms XtepmliU Ctx xhxhep tn iXmaa tes smd; d5eemdnh5ei o5l t n5nta 5o (6) a5dtnh5eiL he a5dtnh5e ahinms he 1U2 ti smihpetnms vb nXm SyPERGISORU kU1U2 Tmuxatnm mwtdn ih/mL d5eohpcltnh5eL tes a5dtnh5e ol5u mwhinhep vtlpm d5eshnh5eiU kU1Uk Ieintaa emr dahxi tes icv-vtimi he tdd5lstedm rhnX 2U9U kU1U4 Add5uxahiX nXm lmqchlmumeni 5o 00#-12 5o 2U1L hedacshep Ttvam kL C5acue AL 3hemi Oem nXl5cpX 9U kU1U4U1 Add5uxahiX e5esminlcdnhgm nminhep he tdd5lstedm rhnX 3hem 11U kU2 Add5uxahiX nXm lmqchlmumeni 5o 00#-2D 5o 2U1 o5l a5dta thl X5im nmin he rtb 5o emr tnntdXumen rmasi 5e rtnmlnhpXn vca;XmtsiL tes smd; iclotdmi he a5dtnh5e 1U2U Aaa5rtvam amt;tpm: N5emU kUk Add5uxahiX nXm lmqchlmumeni 5o 00#-k2 5o 2U1L hedacshep Ttvam DL 3hemi kL 4L D 5l 6L o5l henmlh5l iclotdmi 5o vca;Xmtsi tes iXmaa

N390…