N0042119Q0627.doc

Section B - Supplies or Services and Prices

P/N:DT1000

FFP

DT1000 Dynamometer w/load cell, speed sensor & bearing temp measurment Thermocoule

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

FOB: Destination

MFR PART NR: DT1000

PSC CD: 1680

NET AMT

P/N:TCA1000

Torque Calibration Arm Assembly

FOB: Destination

NET AMT

P/N:DC-100

Servo Load Control Valve (DT1000 Dyno)

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

NET AMT

P/N:IKIT-004/005-40

DT1000 Dyno Single Ended Harness - 40ft

NET AMT

Section C - Descriptions and Specifications

SOW

STATEMENT OF WORK

August 30, 2019

NRADD MQ-8C Drive System Dynamometer

1.0 INTRODUCTION

The Helicopter Drive Systems (HEDS) Test Facility, located at Naval Air Warfare Center

Aircraft Division building 2360, is used to conduct tests on helicopter drive system components. An upcoming NRADD (Navy Rotorcraft Advanced Diagnostic Development) test requires a Dynamometer to simulate flight loads to be able to perform the following: test new

HUMS software builds, Diagnostics/sensor testing for Conditioned Based Maintenance (CBM) intervals, Seeded fault testing, Recuperator, generator, and advanced health monitoring sensors. With this new dynamometer, we will have the capability of simulating the loads at the tail rotor of the MQ-8C aircraft to be able to perform diagnostic development/calibration with the HUMS software. This statement of work is for the components required for the new tail dynamometer.

2.0 SCOPE

The scope of this procurement it to purchase the items as described in quotation # 19-299

Rev. 5 provided by Froude Inc. HeDS engineers/technicians installation and electronically interface the new Froude DT1000 dynamometer to the MQ-8C drive system capabilities for

NRADD testing.

3.0 TECHNICAL REQUIREMENTS

The new dynamometer must be able to test under these parameters:

100% speed 2,500 RPM

Max Cont. Power 168hp

Max Trans Power 231hp

Max Cont. Torque 4235 in-lbf

Max Trans Torque 5,824 in-lbf

Electronically control in control room

40 ft harness length

Torque calibration arms to be able to recalibrate

4.0 DELIVERABLE PRODUCTS

FROUDE, INC. Cage: 6Z252

(1) (DT1000) Dynamometer w/load cell, speed sensor & bearing temp measurement Thermocouple

(1) (TCA1000) Torque Calibration Arm Assembly

(1) (DC-100) Servo Load Control Valve (DT1000 Dyno)

(1) (IKIT-004/005-40) DT1000 Dyno Single Ended Harness - 40ft

5.0 DELIVERY INFORMATION

All hardware shall be delivered to:

PSEF bldg 2360

22229 Elmer road

Patuxent River, MD 20670 Section E - Inspection and Acceptance

INSPECTION AND ACCEPTANCE TERMS

Supplies/services will be inspected/accepted at:

Section F - Deliveries or Performance

DELIVERY INFORMATION

31-JAN-2020

NAWC-AD

22229 ELMER ROAD, BLDG 2360

PATUXENT RIVER MD 20670-1161

N00421

31-JAN-2020

N00421

31-JAN-2020

N00421

31-JAN-2020

N00421

CLAUSES INCORPORATED BY REFERENCE

Section G - Contract Administration Data

Section I - Contract Clauses

Section K - Representations, Certifications and Other Statements of Offerors

CLAUSES INCORPORATED BY FULL TEXT

52.209-11 REPRESENTATION BY CORPORATIONS REGARDING DELINQUENT TAX LIABILITY OR A FELONY CONVICTION UNDER ANY FEDERAL LAW (FEB 2016)

(a) As required by sections 744 and 745 of Division E of the Consolidated and Further Continuing Appropriations Act, 2015 (Pub.L. 113-235), and similar provisions, if contained in subsequent appropriations acts, the Government will not enter into a contract with any corporation that --

(1) Has any unpaid Federal tax liability that has been assessed, for which all judicial and administrative remedies have been exhausted or have lapsed, and that is not being paid in a timely manner pursuant to an agreement with the authority responsible for collecting the tax liability, where the awarding agency is aware of the unpaid tax liability, unless an agency has considered suspension or debarment of the corporation and made a determination that suspension or debarment is not necessary to protect the interests of the Government; or

(2) Was convicted of a felony criminal violation under any Federal law within the preceding 24 months, where the awarding agency is aware of the conviction, unless an agency has considered suspension or debarment of the corporation and made a determination that this action is not necessary to protect the interests of the Government.

(b) The Offeror represents that --

(1) It is [ ] is not [ ] a corporation that has any unpaid Federal tax liability that has been assessed, for which all judicial and administrative remedies have been exhausted or have lapsed, and that is not being paid in a timely manner pursuant to an agreement with the authority responsible for collecting the tax liability; and

(2) It is [ ] is not [ ] a corporation that was convicted of a felony criminal violation under any Federal law within the preceding 24 months, 4.4.1.1

NAWC-AD

22229 ELMER ROAD, BLDG 2360

PATUXENT RIVER MD 20670-1161

TEL: FAX:

REQUEST FOR QUOTATIONS

(THIS IS NOT AN ORDER)

PAGE OF PAGES

1. REQUEST NO.

2. DATE ISSUED

RATING

N0042119Q0627

16-Sep-2019

5a. ISSUED BY

8. TO: NAME AND ADDRESS, INCLUDING ZIP CODE

IMPORTANT:

This is a request for information, and quotations furnished are not offers. If you are unable to quote, please so indicate on this form and return it to the address in Block 5a. This request does not commit the Government to pay any costs incurred in the preparation of the submission of this quotation or to contract for supplies or services. Supplies are of domestic origin unless otherwise indicated by quoter. Any representations and/or certifications attached to this

Request for Quotations must be completed by the quoter.

11. SCHEDULE

(Include applicable Federal, State, and local taxes)

ITEM NO.

(a)

SUPPLIES/ SERVICES

(b)

QUANTITY

(c)

UNIT

(d)

UNIT PRICE

(e)

(f)

SEE SCHEDULE

Total amount:__________

Lead time:_____________

AMOUNT

No.

NOTE: Additional provisions and representations [ ] are [ ] are not attached.

13. NAME AND ADDRESS OF QUOTER

(Street, City, County, State, CAGE and

ZIP Code)

14. SIGNATURE OF PERSON AUTHORIZED TO

SIGN QUOTATION

15. DATE OF

QUOTATION

16. NAME, TITLE AND EMAIL OF SIGNER

(Include area code)

TELEPHONE NO.

AUTHORIZED FOR LOCAL REPRODUCTION

STANDARD FORM 18

(REV. 6-95)

PREVIOUS EDITION NOT USABLE

Prescribed by GSA

FAR (48 CFR) 53.215-1(a)

THIS RFQ

X

[ ] IS

[ ] IS NOT A SMALL BUSINESS SET-ASIDE

6. DELIVER BY

(Date)

SEE SCHEDULE

AND/OR DMS REG. 1

UNDER BDSA REG. 2

4. CERT. FOR NAT. DEF.

3. REQUISITION/PURCHASE

REQUEST NO.

NAVAL AIR WARFARE CENTER AD (PAX) __

2.5.1 RAC, 21983 BUNDY ROAD, BLDG 441

PATUXENT RIVER MD 20670-1127

9. DESTINATION

(Consignee and address, including ZIP Code)

7. DELIVERY

X

FOB

DESTINATION

[ ] OTHER

(See Schedule)

18-Sep-2019

(Date)

PLEASE FURNISH QUOTATIONS TO THE ISSUING OFFICE IN BLOCK 5a ON OR BEFORE CLOSE OF BUSINESS:

10.

benjamin.r.flores@navy.mil

BENJAMIN R. FLORES JR.

(Name and Telephone no.) (No collect calls)

5b. FOR INFORMATION CALL:

d. CALENDAR DAYS

c. 30 CALENDAR DAYS

b. 20 CALENDAR DAYS

12. DISCOUNT FOR PROMPT PAYMENT

a. 10 CALENDAR DAYS