CLIN_DESCRIPTION.doc

EMPHASIS/ADDITIONS/EXCEPTIONS/DESCRIPTIONS

N00244-13-R-0048

CLIN 0001

DESCRIPTION

(CONTINUED)

1. CORRUGATED STEEL SIDES, ROOF+ SWING DOORS ON ONE SIDE

2.

HEAVY DUTY STEEL FLOOR (4) WAY FORK LIFT POCKETS

3. WALL TIE DOWN STEEL LASHING RINGS, 4,000 LBS. CAP. EACH (16 TOTAL)

4. DOOR CORNER POST TIE DOWNS (10 TOTAL)= RESTRAINT SYSTEM, SHORING SLOT WILL SUPPORT 2" X 6" LUMBER

5. VENTS, (2) EACH (CLOSEABLE)

6. MANIFEST BOX (2) EACH (ON THE RIGHT DOOR, ONE INSIDE AND ONE OUTSIDE)

7. CONNECTING COUPLERS, (3) PER TRICON

8. CONNECTING COUPLER STORAGE BRACKET (1) EACH

MIL-PRF-32349A APPLIES WITH EMPHASIS, ADDITIONS, AND EXCEPTIONS AS LISTED BELOW:

3.3.11 VENTS. ALL CONTAINERS SHALL HAVE MINIMUM OF TWO PASSIVE VENTILATING SYSTEMS COMPARABLE TO THOSE USED ON COMMERCIAL ISO CONTAINERS. THE VENTS SHALL BE LOCATED IN UPPER DIAGONAL CORNERS ON OPPOSITE WALLS OR DOORS SUCH THAT THEY PROVIDE MAXIMUM DIAGONAL CROSS AIRFLOW AND HOT AIR EXHAUST, AND THEY SHALL BE DESIGNED TO DEFLECT RAIN OR SPRAY AND PREVENT WATER INGRESS. AS A MINIMUM, THE EXTERNAL VENTING SURFACE AREA OF EACH VENT SHALL BE 452 MM2 (0.7 IN2) TO PERMIT DEPRESSURIZATION OF THE TRICON DURING AIR TRANSPORTATION. VENTS SHALL BE ABLE TO BE OPENED AND CLOSED, WITHOUT TOOLS FROM THE OUTSIDE OF THE TRICON. THERE SHALL BE NO AIR FLOW THROUGH THE VENTS WHEN THEY ARE IN THE CLOSED POSITION. THESE OPENING AND CLOSING VENTS SHALL BE ABLE TO LOCK IN PLACE IN BOTH THE OPEN AND CLOSED POSITIONS SUCH THAT THEY SHALL REMAIN IN THEIR SET POSITION.

3.3.12 MANIFEST BOX. TWO MANIFEST BOXES SHALL BE PROVIDED ON EACH CONTAINER. ONE SHALL BE SECURELY AND RIGIDLY FASTENED TO THE INSIDE OF THE RIGHT HAND DOOR, AND ONE TO A FLAT SURFACE OF THE OUTSIDE UPPER PORTION OF THE RIGHT HAND DOOR. THE MANIFEST BOX ON THE INSIDE SHALL NOT INTERFERE WITH THE SHELVING AREA AT ANY LEVEL. THE MANIFEST BOX ON THE OUTSIDE SHALL BE DESIGNED AND LOCATED IN AN AREA THAT MINIMIZES INTERFERENCE OR DAMAGE WITH FORKLIFT CARRIAGES AND BACKRESTS BEING USED TO LIFT THE TRICON. THE MANIFEST BOX SHALL BE WEATHER TIGHT WITH A HINGE TYPE COVER, PAINTED TO MATCH THE INTERIOR OR EXTERIOR COLOR. THE MANIFEST BOX SHALL BE DESIGNED TO HOLD AN 8-1/2 INCHES BY 11 INCHES BY 1-1/4 INCHES THICK DOCUMENT (215.9 MM BY 279.4 MM BY 31.75 MM).

3.5.2 FORKLIFT POCKETS AND RELIEF NOTCHES. THE CONTAINER SHALL HAVE FORKLIFT POCKETS THAT CONFORM TO ISO 1496-1, ANNEX C, UNLESS OTHERWISE SPECIFIED IN THIS PARAGRAPH. THE CONTAINERS SHALL HAVE FOUR-WAY ENTRY, AND THE ENTRY POINTS SHALL NOT INTERFERE WITH THE DOORS OR DOOR HEIGHT REQUIREMENTS. A RELIEF NOTCH SHALL BE PROVIDED ALONG THE BOTTOM RAIL AT THE CORNER BLOCK ON ALL FOUR SIDES OF EACH TRICON. THE FORKLIFT POCKETS ON THE DOOR SIDE AND THE SIDE WALL OPPOSITE OF THE DOOR SIDE SHALL BE A MINIMUM OF 4.5 INCHES HIGH AND 14.0 INCHES WIDE. THE FORKLIFT POCKETS ON THE FRONT AND REAR END WALLS SHALL BE A MINIMUM OF 4.0 INCHES HIGH AND 12.0 INCHES WIDE AND CONFORMING WITH ISO 1496-1.

3.6.1 EXTERIOR MARKINGS. FOR ALL OTHER MARKINGS. ALL LETTERS SHALL BE GOTHIC OR FUTURA CAPITALS WITH ARABIC NUMERALS AND SHALL READ FROM LEFT TO RIGHT. THE STENCLING MEDIUM SHALL BE WHITE, FED-STD-595 COLOR #37875. STENCILING MEDIUM SHALL NOT RUB OFF THE EXTERIOR SURFACE OF THE CONTAINER WHEN THE MEDIUM IS DRY.

3.6.3 APPROVAL PLATES. AN INTERNATIONAL CONVENTION FOR SAFE CONTAINERS (CSC), PLATES OR PLAQUES SHALL BE APPLIED FOR AND OBTAINED FROM A DESIGNATED APPROVAL AUTHORITY AND ATTACHED AND DISPLAYED AS REQUIRED BY THE CSC, IN ACCORDANCE WITH 49CFR450 THROUGH 49CFR453. EACH TRIGON SHALL BE AFFIXED WITH THE SEAL OF THE APPROVAL AUTHORITY.

DATA PLATE: A NONFERROUS METAL DATA PLATE CONFORMING TO A-A-50271 SHALL BE AFFIXED TO THE CENTER OF THE EXTERNAL SURFACE OF THE RIGHT HAND DOOR. THE METHOD OF ATTACHMENT SHALL BE EITHER RIVETING OR BOLTING. THE DATA SUPPLIED ON THE PLATE SHALL BE AS FOLLOWS:

CONTAINER SHIPPING AND STORAGE, STEEL WALL (TYPE II STYLE I)

NSN: 8145-01-287-3294

ISO CONTAINER CONTROL NUMBER

EQUIPMENT CODE: XM03TB

TARE WEIGHT:

LBS

KG

CONTRACT NUMBER:

MFGBY

DATE: (MONTH AND YEAR)

3.6.4 CONSOLIDATED DATA PLATE. A CONVENTION FOR SAFE CONTAINERS (CSC) SAFETY APPROVAL PLATE CONFORMING TO 49 CFR451, SUBPART C, WITH THE APPROPRIATE INFORMATION STAMPED, ETCHED, OR ENGRAVED ON IT SHALL BE RIVETED OR BOLTED TO THE LOWER LEFT CORNER OF THE EXTERIOR FACE OF THE LEFT HAND DOOR OF EACH CONTAINER.

ALL OTHER REQUIREMENTS OF MIL-PRF-32349A REMAIN THE SAME. CONTAINER SHALL CONFORM TO ISO 668 AND IS01496-1. CARGO CONTAINERS ARE TO BE NEW AND UNUSED.

ITEM UNIQUE IDENTIFICATION (IUID):

Marking of major end items, reporting and registration per DFARS CLAUSE 252.211-7003, Item identification and valuation, Reference MIL-STD-130N.

SPECIAL INSTRUCTIONS:

The following notation must be shown on all orders, contracts, bills of lading, correspondence, crates, boxes, shipment markings, DD-250s etc., pertaining to procurement and shipment of this equipment:

"N62583-13-RC-NF303"

The Contractor/Vendor shall contact the NAVFAC EXWC Procurement Management Branch point of contact no later than 30 days prior to delivery to validate RECEIVING OFFICER destination information. Points of Contact as follows:

Raul A. Mantes

(805) 982-3045 Raul.mantes @ navy.mil Lisa Vannoy

(805) 982-3257 Lisa.vannoy @ navv.mil

SHIPPING DOCUMENTS

All shipping documents, including MATERIAL INSPECTION AND RECEIVING REPORTS (DD Forms 250 Series) or CONTRACTOR'S COMMERCIAL SHIPPING NOTICES, shall be expanded to include the following information, as applicable, to permit ready identification of the appropriate procurement transaction and provide required control information:

1. Prime contractor's Name and address.

2. "Shipped from" location if different.

3. "Shipped to" code and address.

4. "Marked for" code and address.

5. Contract or Purchase Order Number.

6. DOCUMENT or Requisition Number.

7. Appropriation and Accounting Data.

8. Description of item(s) delivered.

9. National Stock Number if assigned.

10. Prime contractor's Make, Model and Serial Number.

11. Engine manufacturer's Name, Model and Engine Serial Number.

12. Navy Registration Number applicable to each serial number.

13. Quantity of items delivered.

14. Unit price and extended total price.

15. Date of shipment.

16. Weight and cube.

17. Port of Embarkation if overseas destination.

18. Special shipping instructions as specified in the contract or purchase order.

19. A descriptive list including quantity of items shipped, with the CLIN, but not permanently attached thereto, i.e., tools, jacks, manuals, spare tire, etc.

DISTRIBUTION OF SHIPPING DOCUMENTS SHALL BE AS FOLLOWS:

ALL SHIPMENTS:

Two copies DD Form 250 or proof of shipping to:

COMMANDING OFFICER

NAVAL FACILITIES ENGINEERING AND EXPEDITIONARY WARFARE CENTER ATTN: CODE EX205

1000 23RD AVENUE

PORT HUENEME, CA 93043-4301