SOW.doc

STATEMENT OF WORK

HONEYCOMB DOOR AND JOINER BULKHEAD MATERIAL

This requirement is in support of the USS Gonzalez and USS Mason.

USS GONZALEZ (DDG 66)

HONEYCOMB MATERIAL (OPEN PURCHASE)

PROJECT: BOFF-S9775 / HOFF-S9776 / ERPR-R9913

3/32" THICK 48" LONG

DWG: 804-4623540 REV A

PIECE NO. 20.

ADHESIVE NOT REQUIRED.

ADVANCED STRUCTURES PART # ASC-235-77N OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0077N ARR)

V21833-9099-0159

MARK FOR: GONZALEZ (DDG 66)

PROJECT: BOFF-S9775

FOR HONEYCOMB

DWG: 804-4623540, REV A

MATERIAL: ALUMINUM

PC. 21 (QTY 2) AND PC 23 (QTY 2)

NATURAL ANODIZED FINISH

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0703 ARR)

V21833-9099-0160

MARK FOR: GONZALEZ (DDG 66)

PROJECT: BOFF-S9775

FOR HONEYCOMB

DWG: 804-4623540, REV A

MATERIAL: ALUMINUM

PC. 22

NATURAL ANODIZED FINISH

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0705 ARR)

V21833-9099-0161

MARK FOR: GONZALEZ (DDG 66)

PROJECT: BOFF-S9775

DWG: 804-4623540, REV. A

MATERIAL: HPPL ON ALUM

PIECE NO. 24 HIGH PRESSURE PLASTIC

LAMINATE COVERED ALUMINUM HONEYCOMB.

ADVANCED STRUCTURES PART # ASC-235-711 OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

PANOLAM NEVAMAR SPA WHITE S-7040.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0711 ARR)

V21833-9099-0162

MARK FOR: GONZALEZ (DDG 66)

PROJECT: BOFF-S9775

12 GA

DWG: 807-6570099, DET 39

SPEC: ASTM A240

MATERIAL: SST TYPE 304L

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0720 ARR)

V21833-9099-0163

MARK FOR: GONZALEZ (DDG 66)

PROJECT: BOFF-S9775

HONEYCOMB, COMBINATION. WITH SILL AND LOUVER

DWG: 805-4629248, REV -

MATERIAL: ALUMINUM

RIGHT-HAND WITH SILL 1-5/8" PER DETAIL 2-K AND

LOUVER TYPE IV. (12" X 12")

EXCEPT WITH COMBINATION LOCK KABA 1011-26D-41.

ADVANCED STRUCTURES PART # ASC-235-790S OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

THIS DOOR IS INTENDED FOR APPLICATIONS SUCH AS STATEROOMS, WITH A SMALL LOUVER AND COMBINATION LOCK. AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM (FIND NO. 0790S ARR) V21833-9099-0164

MARK FOR: GONZALEZ (DDG 66)

PROJECT: BOFF-S9775

HONEYCOMB, COMBINATION. WITH SILL AND LOUVER

DWG: 805-4629248, REV -

MATERIAL: ALUMINUM

LEFT-HAND WITH SILL 1-5/8" PER DETAIL 2-K AND

LOUVER TYPE IV. (12" X 12")

EXCEPT WITH COMBINATION LOCK KABA 1011-26D-41.

ADVANCED STRUCTURES PART # ASC-235-791S OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

THIS DOOR IS INTENDED FOR APPLICATIONS SUCH AS STATEROOMS, WITH A SMALL LOUVER AND COMBINATION LOCK.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0791S ARR)

V21833-9099-0165

MARK FOR: GONZALEZ (DDG 66)

PROJECT: BOFF-S9775

DWG: 807-6570099, DET 83

MATERIAL: STAINLESS 304

ADVANCED STRUCTURES PART NO. PMS142058-304 IS ACCEPTABLE.

USES DRILLED SPANNER BIT SIZE #14.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 1435 ARR)

V21833-9099-0166

MARK FOR: GONZALEZ (DDG 66)

PROJECT: BOFF-S9775

DWG: 807-6570099, DET 73

SPEC: ASTM A240

MATERIAL: SST TYPE 304L

EA = 8 FT

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 1801 ARR)

V21833-9099-0167

MARK FOR: GONZALEZ (DDG 66)

PROJECT: BOFF-S9775

3/32" THICK 48" LONG

DWG: 804-4623540 REV A

PIECE NO. 20.

ADHESIVE NOT REQUIRED.

ADVANCED STRUCTURES PART # ASC-235-77N OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0077N ARR)

V21833-9099-0168

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

DWG: 807-6570099 DET 77

SPEC: ASTM A240

MATERIAL: SST TYPE 304L

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0399F ARR)

V21833-9099-0169

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

30 1/2" WIDE BY 20" LONG

DWG: 803-5959189, REV -

MATERIAL: SST TYPE 304L

TYPE 304L STAINLESS STEEL FACED NOMEX CORE.

ADVANCED STRUCTURES PART # ASC-235-594H OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0594H ARR)

V21833-9099-0170

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

DWG: 807-6570099, DET 72

SPEC: ASTM A240

MATERIAL: SST TYPE 304L

FOR HONEYCOMB

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0706 ARR)

V21833-9099-0171

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

FOR HONEYCOMB

DWG: 807-6570099, DET 55

SPEC: ASTM A240

MATERIAL: SST TYPE 304L

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0708 ARR)

V21833-9099-0172

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

7'-0" LONG, FOR HONEYCOMB

DWG: 807-6570099, DET 55 MOD

SPEC: ASTM A240

MATERIAL: SST TYPE 304L

Pacific Marine Systems PMS-9619-708P or equal.

807-6570099, DET 55 MOD TO 5/8" OUTSIDE WIDTH INSTEAD OF INSIDE WIDTH, AND DEPTH OF 3/4" INSTEAD OF 7/8", AND 18 GA (0.048") INSTEAD OF 14 GAGE THICKNESS, AND HOLES ARE NOT REQUIRED.

TOLERANCE ON 5/8" WIDTH IS PLUS OR MINUS 1/64".

(USED IN LIEU OF 803-5959189 PC 12).

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0708P ARR)

V21833-9099-0173

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

24" WIDE BY 84" LONG

DWG: 803-5959189, REV -

MATERIAL: SST TYPE 304L

TYPE 304L STAINLESS STEEL FACED NOMEX CORE.

ADVANCED STRUCTURES PART # ASC-235-710 OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0710 ARR)

V21833-9099-0174

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

48" WIDE BY 84" LONG

DWG: 803-5959189, REV -

MATERIAL: SST TYPE 304L

TYPE 304L STAINLESS STEEL FACED NOMEX CORE.

ADVANCED STRUCTURES PART # ASC-235-712 OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0712 ARR)

V21833-9099-0175

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

12 GA

DWG: 807-6570099, DET 39

SPEC: ASTM A240

MATERIAL: SST TYPE 304L

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0720 ARR)

V21833-9099-0176

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

12" HIGH X 10 GA (0.135")

DWG: 807-6570099, DET 39

SPEC: ASTM A240

MATERIAL: SST TYPE 304L

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0720X ARR)

V21833-9099-0177

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

HONEYCOMB. WITH SILL AND LOUVER

DWG: 805-4629248, REV -

MATERIAL: ALUMINUM RIGHT HAND WITH SILL AND LOUVER TYPE VII.

ADVANCED STRUCTURES PART # ASC-235-768 OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0768 ARR)

V21833-9099-0178

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

HONEYCOMB. WITH SILL AND LOUVER

DWG: 805-4629248, REV -

MATERIAL: ALUMINUM

LEFT-HAND WITH SILL AND LOUVER TYPE VII.

ADVANCED STRUCTURES PART # ASC-235-769 OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0769 ARR)

V21833-9099-0179

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

HONEYCOMB, WITHOUT CLOSER. WITH SILL AND LOUVER

DWG: 805-4629248, REV -

MATERIAL: ALUMINUM

LEFT-HAND WITH SILL AND LOUVER,

TYPE VII. FOR 6-1/4" SILL HEIGHT.

WITHOUT CLOSER AND NOT DRILLED FOR CLOSER.

ADVANCED STRUCTURES PART # ASC-235-787NC OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0787NC ARR)

V21833-9099-0180

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

DWG: 807-6570099, DET 73

SPEC: ASTM A240

MATERIAL: SST TYPE 304L

EA = 8 FT

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 1801 ARR)

V21833-9099-0181

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

12" WIDE BY 84" LONG

DWG: 803-5959189, REV -

TYPE 304L STAINLESS STEEL FACED NOMEX CORE.

ADVANCED STRUCTURES PART # ASC-235-1806 OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 1806 ARR)

V21833-9099-0182

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

36" WIDE BY 84" LONG

DWG: 803-5959189, REV -

TYPE 304L STAINLESS STEEL FACED NOMEX CORE.

ADVANCED STRUCTURES PART # ASC-235-1808 OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 1808 ARR)

V21833-9099-0183

MARK FOR: GONZALEZ (DDG 66)

PROJECT: HOFF-S9776

USS MASON (DDG 87)

HONEYCOMB MATERIAL (OPEN PURCHASE)

PROJECT: BENL-S8286 / BCPO-S2291 / HENL-S8269 / HCPO-S2293

FOR HONEYCOMB TO JO PANEL

DWG: 807-6570099, DET 48

SPEC: ASTM A240

MATERIAL: SST TYPE 304L AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0399C ARR)

V22995-9133-0225

MARK FOR: MASON (DDG 87)

PROJECT: HENL-S8269 / HCPO-S2293

HONEYCOMB. WITH SILL

DWG: 805-4629248, REV -

MATERIAL: ALUMINUM

LEFT-HAND WITH SILL.

ADVANCED STRUCTURES PART # ASC-235-767 OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

*** QUALIFICATION TESTING DOCUMENTATION REQUIRED WITH QUOTE. ***

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0767 ARR)

V22995-9133-0226

MARK FOR: MASON (DDG 87)

PROJECT: HENL-S8269 / HCPO-S2293

HONEYCOMB. WITH SILL

DWG: 805-4629248, REV -

MATERIAL: ALUMINUM

LEFT-HAND WITH SILL.

ADVANCED STRUCTURES PART # ASC-235-767 OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

*** QUALIFICATION TESTING DOCUMENTATION REQUIRED WITH QUOTE. ***

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0767 ARR)

V22995-9133-0227

MARK FOR: MASON (DDG 87)

PROJECT: BENL-S8286 / BCPO-S2291

HONEYCOMB. WITH SILL AND LOUVER

DWG: 805-4629248, REV -

MATERIAL: ALUMINUM

RIGHT HAND WITH SILL AND LOUVER TYPE VII.

ADVANCED STRUCTURES PART # ASC-235-768 OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0768 ARR)

V22995-9133-0228

MARK FOR: MASON (DDG 87)

PROJECT: HENL-S8269 / HCPO-S2293

HONEYCOMB. WITH SILL AND LOUVER

DWG: 805-4629248, REV -

MATERIAL: ALUMINUM

LEFT-HAND WITH SILL AND LOUVER TYPE VII.

ADVANCED STRUCTURES PART # ASC-235-769 OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0769 ARR)

V22995-9133-0229

MARK FOR: MASON (DDG 87)

PROJECT: HENL-S8269 / HCPO-S2293

HONEYCOMB. WITH SILL AND LOUVER

DWG: 805-4629248, REV -

MATERIAL: ALUMINUM

RIGHT-HAND WITH SILL AND LOUVER,

TYPE VII. FOR 6-1/4" SILL HEIGHT.

ADVANCED STRUCTURES PART # ASC-235-786 OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0786 ARR)

V22995-9133-0230

MARK FOR: MASON (DDG 87)

PROJECT: HENL-S8269 / HCPO-S2293

HONEYCOMB, WITHOUT CLOSER. WITH SILL AND LOUVER

DWG: 805-4629248, REV -

MATERIAL: ALUMINUM

RIGHT-HAND WITH SILL AND LOUVER,

TYPE VII. FOR 6-1/4" SILL HEIGHT.

WITHOUT CLOSER AND NOT DRILLED FOR CLOSER.

ADVANCED STRUCTURES PART # ASC-235-786NC OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0786NC ARR)

V22995-9133-0231

MARK FOR: MASON (DDG 87)

PROJECT: HENL-S8269 / HCPO-S2293

HONEYCOMB, WITHOUT CLOSER. WITH SILL AND LOUVER

DWG: 805-4629248, REV -

MATERIAL: ALUMINUM

LEFT-HAND WITH SILL AND LOUVER,

TYPE VII. FOR 6-1/4" SILL HEIGHT.

WITHOUT CLOSER AND NOT DRILLED FOR CLOSER.

ADVANCED STRUCTURES PART # ASC-235-787NC OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0787NC ARR)

V22995-9133-0232

MARK FOR: MASON (DDG 87)

PROJECT: HENL-S8269 / HCPO-S2293

HONEYCOMB, COMBINATION. WITH SILL AND LOUVER

DWG: 805-4629248, REV -

MATERIAL: ALUMINUM

RIGHT-HAND WITH SILL 1-5/8" PER DETAIL 2-K AND LOUVER TYPE VII.

EXCEPT WITH COMBINATION LOCK KABA 1011-26D-41.

ADVANCED STRUCTURES PART # ASC-235-790C OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0790C ARR)

V22995-9133-0233

MARK FOR: MASON (DDG 87)

PROJECT: BENL-S8286 / BCPO-S2291

HONEYCOMB. WITH SILL AND LOUVER

DWG: 805-4629248, REV -

MATERIAL: ALUMINUM

LEFT-HAND WITH SILL PER DETAIL 2-K AND LOUVER TYPE VII.

ADVANCED STRUCTURES PART # ASC-235-791 OR EQ.

HONEYCOMB QUALIFICATION APPROVAL DOCUMENT FOR ANY PROPOSED EQUAL TO BE INCLUDED WITH QUOTE, AND SUBJECT TO APPROVAL OF MARMC.

AND SHALL BE IAW HH NOTES DATED 6/8/2015. POSTED AT MSCORPHAB.COM

(FIND NO. 0791 ARR)

V22995-9133-0234

MARK FOR: MASON (DDG 87)

PROJECT: BENL-S8286 / BCPO-S2291

C.I DESCRIPTIONS/SPECIFICATIONS

C.I.1

OVERVIEW

A. The purpose of this contract is to provide a means to purchase Honeycomb Doors and Joiner Bulkhead Material (as defined within the scope of work herein) and related material in support of the NAVSEA Shipboard Habitability Improvement Program at competitive prices in accordance with the delivery schedules herein.

B. The Contractor acknowledges that the contract is NOT an exclusive or mandatory source of supply for any of the contract line items herein. The U.S. Navy has the right at any time to establish contracts, concessions, or other commercial arrangements that could create competition, if such is deemed in the best interests of the U.S. Navy. The Contractor shall not be entitled to an exclusive presence at any Government facility, activity, station, base or post.

C.I.2 ALL ITEMS SHALL COMPLY WITH THE FOLLOWING REQUIREMENTS:

A. All items shall be manufactured and inspected in accordance with Military Performance Specification MIL-PRF-32038, "Shipboard Furniture, Fixtures, Fittings, and Accessories, General Specification for." This specification supersedes MIL-F-902, "Furniture, Shipboard, Aluminum, General Specification for." Where the requirements of the invoked drawing differ from those of MIL-PRF-32038, the drawing shall prevail. Where the requirements of the Contract Line Item Description or this Statement of Work differ from the invoked drawing or MIL-PRF-32038, the Contract Line Item Description and this Statement of Work shall prevail.

B. Sections 3.5.5, 3.7, 4.4.4 and 4.4.7 of MIL-PRF-32038 do not apply. The drawings invoked by the Contract Line Item Description or elsewhere in this section shall be fully complied with and take the place of any Specification Sheets under MIL-PRF-32038. CRES and SST are abbreviations for stainless steel. Unless otherwise indicated, all visible stainless steel shall have a Number 4 finish.

C. All paint shall meet the performance, testing, and inspection criteria of ASTM F1178-11. Paint testing is not required on steel panels. Paint testing is only required at the start of production under this solicitation, and thereafter only after a change is made to the painting procedure, equipment or supplies.

D. Drawings listed in the CLIN "DWGS" field are posted on www.MSCorpHab.comwww.MSCorpHab.com. Unless otherwise indicated, abbreviations are in accordance with ASME Y14.38, or .

E. Many Military and Federal Specifications are being canceled and/or converted to commercial equivalents. Referenced drawings have not in all cases been updated to cite the currently applicable specification. Contract Line Item Descriptions cite current specifications. If a referenced specification has been canceled without replacement and the Contract Line Item Description or this Statement of Work do not cite an updated replacement specification, the Contractor may substitute a commercial equivalent. If there are option choices available within the cited specifications that are not specified by the contract, the Contractor shall select the grades and conditions etc. as the Contractor recommends.

F. Unless otherwise stated, the applicable revision of each specification shall be the one in effect on 1 April 2015 per the Acquisition Streamlining and Standardization Information System (ASSIST) database for Government documents, and www.NSSN.org for commercial documents. See URL quicksearch.dla.mil for the ASSIST database.

G. All items shall be made strictly in accordance with the invoked drawing and this Statement of Work except where a Request for Deviation (RFD) or Engineering Change Proposal (ECP) has been approved explicitly for this contract.

(1) RFDs and ECPs must be precisely defined. The government may require detailed sketches, drawings, data or samples to clarify and document any requests. Due to the Habitability nature of the items, appearance is a factor in the evaluation of all RFDs and ECPs. Submittals shall include contract number, applicable CLIN and Find Number, description of the differences, reason for the differences, cost impact, schedule impact, identification of units which are affected, any effect on logistics support, action taken to prevent future recurrence of any non-conformance, reference to all previous correspondence that is related to the RFD or ECP or similar requests, and the contractor's point-of contact including phone number, fax number, and e-mail address. Submittals shall be in the contractor's format. The submission of requests via electronic means (e.g., e-mail) is preferred.

(2) Reference to a manufacturer's model number or item number is intended to be descriptive and not restrictive. The referenced items represent the required sizes, configuration, materials, finish, quality, and workmanship. Alternate proposals for items that are believed equal or a better value to the government are welcome.

(3) For any item, vendors may propose equivalent commercial items. For each alternate or substitute item, the vendor's proposal shall include a detailed description and catalog cuts, including renderings or photographs. Additional detail, drawings, or even a sample, may be required to obtain approval if the catalog and description does not adequately describe the item.

(4) Approval of all Drawings, Substitutes, Deviations, RFDs, or ECPs shall be by the requiring activity Mid-Atlantic Maintenance Center (MARMC) Code 226. Requests shall be e-mailed to MARMC (baldev.gill@navy.mil) by the vendor at the same time they are submitted to the PCO via the ACO.

(5) Vendor shall forward a copy of all orders, modifications, and changes to baldev.gill@navy.mil and kevin.f.baker@navy.mil upon receipt.

(6) The MARMC Program Manager will forward the Government response to the vendor, via the PCO/ACO, not later than thirty (30) days after receipt. Time will not be added to the vendor's production schedule because of failure to identify and submit requested deviations, waivers, drawings, or requests for clarification.

H. Due to short procurement lead time, schedule does not permit qualification to be accomplished under this order. Bidders must submit with their quote, documentation of previously approved testing, requesting extension of prior approval for this order/contract.

C.I.3 ITEMS WITH HONEYCOMB CORE

A. For items with honeycomb core, the aluminum core material shall conform to the Grade B material specified in Military Specification MIL-C-7438G with Amendment 1 (historical). If a commercial equivalent material is used, the core must be fabricated from aluminum alloy foil 5052 or 5056 conforming to SAE-AMS-A-81596, and the foil shall be chemically treated for protection against corrosion. The adhesive used to bond the honeycomb core to the face sheets shall conform to SAE-AMS-A-25463, Type I, Class 1, and the adhesive carrier shall be non-hygroscopic.

B. All material, adhesive, and equipment manufacturer's recommendations shall be complied with.

C. All Notes on the referenced drawings shall be complied with. Vendor shall maintain records of all testing and inspection, and shall make them available to the government upon request throughout the life of the contract. Materials, procedures and equipment shall be proven by testing in accordance with SAE-AMS-STD-401 (which supersedes MIL-STD-401) to meet or exceed the minimum properties stated in Notes 2 and 3 of drawing 804-4623540 revision A. In addition, Joiner Doors shall also be tested in accordance with Notes 3, 4 and 5 of drawing 805-4629248. MIL-STD-105 sampling does not apply. Documentation of prior tests on identical materials is acceptable in lieu of new tests. Re-testing is only required if there is a change in procedures or equipment, or a change in the materials or adhesives used.

D. Refer also to C.I.2.H.

C.I.4 JOINER DOORS

A. The manufacturer shall assemble each door complete with frame, door closer, and all hardware. The Door Closer shall be through-bolted. The Closer and Latch Set may be disassembled for packaging and shipment. The manufacturer shall furnish all fasteners, and fasteners provided for field assembly shall include 20 percent spares. Disassembled hardware and fasteners shall be shipped with each door as a kit.

B. The Door Closer shall be in accordance with BHMA A156.4, Type C02011 Size III with option PT 4C, surface mounted, modern type with cover, Grade 1. The finish shall be painted aluminum. The Closer shall be reversible.

C. All doors shall be furnished with a Latch Set, Piece Number 4 of the Type Drawing. The Latch Set shall be in accordance with BHMA A156.2, Series 4000, Grade 1, Function F75. The chassis, structure and internals shall be stainless steel. The backset shall be 2-3/4". The finish shall be satin stainless steel (BHMA 630), or clear anodized satin on wrought aluminum. The strike plate shall be as recommended by the Latch Set manufacturer to match the Latch Set for this application. The fasteners shall be as recommended by the Latch Set manufacturer for this application and to suit threaded inserts in the door and frame. In addition to the threaded inserts shown on the drawing, stainless steel threaded inserts shall be used in the frame for the strike plate.

D. All doors and frames shall be fitted with Gasket, Piece Number 36 and 55.

E. Retainer, Piece Number 39, shall be furnished with all doors except Type 4.

F. Instead of the hinges called out by the Type Drawing 805-4629248, there shall be a continuous aluminum gear hinge, ROTON model USN 109/042HD079CL, or equal. The salient characteristics are extruded and clear anodized aluminum, half surface continuous gear hinge with plastic bearing blocks, and, as shown in the figure below, with ¼-20 UNC, chrome plated steel or stainless steel sex bolts and with phillips head on the screw. The sex bolt screw may be a flat head or have a shoulder. The barrel, or female portion of the sex bolt shall be aluminum, chrome plated steel or stainless steel.

(1) The hinge shall be cut to approximately ¼-inch less than the length of rectangular doors. The hinge shall be cut to approximately ½-inch less than the distance between the tangent points of radius corner doors. Hinges should be cut at the bottom, but avoid cutting through the plastic bearings. If a cut would fall on a bearing, cut equal amounts from the top and the bottom instead of just cutting from the bottom.

(2) The hinge shall be fastened through all of the pre-drilled holes. The maximum fastener spacing into the frame is 9¼-inches, and the maximum fastener spacing into the door is 14- inches. Fastener spacing is reduced at the top and bottom. Flat head machine screws shall thread into stainless steel thread inserts in the frame similar to the method shown in Detail 4-A on the Type Drawing for the old style hinges. The screws and threaded inserts in the frame shall be 12-24 instead of the 10-24 shown on the drawing. Sex bolts shall bolt through the door for the hinge leaf attached to the door. The phillips head end of the sex bolt shall be installed on the hinge side of the door.

(3) Since the hinge is anodized, the hinge shall not be painted and shall be installed on the door after the door is painted.

(4) The Channel Piece Number 15 in the door near the hinge may need to be trimmed back to clear the hinge. It may be necessary to trim approximately 1/8-inch from the edge of the gasket to position the hinge on the frame.

G. Doors and Frames shall be painted color number 26586 (beige) in accordance with FED‑STD‑595C.

H. A permanent, stamped manufacturer's label shall be provided on each door assembly. The label shall include: Manufacturer, CAGE Code, NAVSEA Drawing Number with Revision, Door Type, Size of clear opening in inches, Left or Right Hand, With Sill or Without Sill (for Type I doors), Louver Type (if applicable), Contract Number, Year and Month of Manufacture, and Find Number. The label shall be located on the frame leaf of the hinge, between fasteners near the bottom, where it will be visible only if the door is open.

I. For purposes of this solicitation, when you are facing a door, and it will open toward you, and the hinges are on your left, it is a left-hand door. Similarly, when you are facing a door, and it will open toward you, and the hinges are on your right, it is a right-hand door.

J. Refer also to C.I.2.H.

C.I.5 BULKHEAD PANELS WITH HIGH PRESSURE PLASTIC LAMINATE (HPPL)

A. For Bulkhead Panels requiring High Pressure Plastic Laminate (HPPL), the laminate shall be fire retardant in accordance with Military Specification MIL-P-17171E, Type IV. The requirements of Military Standard MIL-STD-1623E(1) apply to the plastic laminate component of these line items before the laminate is bonded to the aluminum. The adhesive to be used for bonding the plastic laminate to the aluminum shall be a contact adhesive conforming to Commercial Item Description A‑A‑1936A(4), Type I. Bonding of the laminate to the aluminum shall be accomplished in a manner that will ensure that the laminate does not separate from the aluminum or crack when installed in a shipboard environment. The manufacturer shall be responsible for whatever processing is required to achieve such satisfactory bonding, even if it is over and above the recommendations and conditioning recommended by the adhesive and HPPL manufacturers.

B. The plastic laminate shall be applied to both sides of the bulkhead panel.

C. The color of the laminate shall be equivalent to Panolam Nevamar product Spa White S-7040 with a matte finish.

D. Refer also to C.I.2.H.

C.I.6 STAINLESS STEEL FACED BULKHEAD PANELS

A. Face sheets shall be Type 304L stainless steel per ASTM A240 with a No. 4 finish on both sides of the panel. Both sides shall be protected against damage from handling with a protective vinyl film.

B. All material, adhesive, and equipment manufacturer's recommendations shall be complied with.

C. All Notes on the referenced drawings shall be complied with. Vendor shall maintain records of all testing and inspection, and shall make them available to the government upon request throughout the life of the contract. Materials, procedures and equipment shall be proven by testing in accordance with SAE-AMS-STD-401 (which supersedes MIL-STD-401) to meet or exceed the minimum properties stated on drawing 803-5959189, Rev. -. MIL-STD-105 sampling does not apply. Documentation of prior tests on identical materials is acceptable in lieu of new tests. Retesting is only required if there is a change in procedures or equipment, or a change in the materials or adhesives used.

D. Refer also to C.I.2.H.

PACKAGING AND MARKING

D.I

PRESERVATION, PACKAGING, PACKING AND MARKING

A. Preservation, packaging, packing and marking shall be in accordance with ASTM D3951-2010 "Standard Practice for Commercial Packaging," and as additionally noted herein.

(1) Packaging and packing shall be sufficient to afford adequate protection against deterioration and physical damaging (including marring or abrasion to finished surfaces) during shipment and handling, and packaging shall be suitable for stacking during transit. The vendor is responsible to correct any damage.

(2) Each shipment larger than 70 pounds or 12 cubic feet shall be palletized for handling with a fork lift.

(3) The contractor shall provide a packing list identifying the contents of each shipment with the shipment. DD Form 250 "Material Inspection and Receiving Report" may be used as the packing list provided that it contains all of the information required below and that it applies to the specific shipment.

(4) The use of asbestos, excelsior, loose fill polystyrene, newspaper or shredded paper of all types (including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited.

(5) Delivery Orders may additionally invoke the options and recommendations in ASTM D3951 for export shipments.

D.2 MARKING

In addition to labels and marking required elsewhere, each package, including intermediate and outer containers, and a packing slip with each shipment, shall be marked with each applicable Requisition Number (REQN), Find Number, Discipline, Quantity, and Unit of Issue.

(1) Marking shall be in accordance with ASTM D3951 and the following additional details.

Line 1: Characters 1 thru 16: Requisition number including dashes.

Line 2: Characters 1 thru 6: Find Number, including leading zeros to fill field.

Character 7:

Intentionally left Blank.

Characters 8 thru 11: Discipline such as "ARR", "VENT", "ELEC", or "PIPE" with leading spaces to fill field.

Line 3: Characters 1 thru 5:

Quantity with lead zeros to fill field.

Character 6:

Intentionally left Blank.

Character 7 and 8:

Abbreviated unit of issue.

(2) Each package, including intermediate and outer containers, and packing slip shall also be printed with the contract number, any Delivery Order number, project number such as "BENL-S3078" and the ship name.

(2) A sample label is posted at www.MSCorpHab.com with the Manufacturing Drawings, under Miscellaneous Reference Details.

Unless otherwise indicated, delivery is to:

SW3197

DLA DISTRIBUTION NORFOLK, VA

1968 GILBERT STREET BLDG. W148, DWY 12

ATTN: CODE N, SPECIAL PROGRAMS, HMSC

PH: (757) 443-3174

NORFOLK, VA. 23511

INSPECTION AND ACCEPTANCE (ORIGIN)

(a) The Government inspection of the supplies or services to be furnished hereunder shall be performed by the cognizant Defense Contract Management Agency (DCMA) office at the contractor's or subcontractor's plant located at (to be determined at time of award) and the acceptance of the supplies or services shall be conducted at the government location (to be determined at time of award). The location designated for such inspection and acceptance shall not be changed without prior, written authorization of the Contracting Officer.

(b) The cognizant inspector shall be notified when supplies or services are ready for government inspection.

(c) Advance notification of the cognizant inspector [X] is [ ] is not required at least 7 days prior to conducting inspections and/or testing. (to be completed at time of award.)

The contractor shall respond to any Government corrective documents, such as Quality Deficiency Reports (QDR'S), etc. issued because of unsatisfactory contract performance. The appropriate corrective actions shall be taken by the contractor and written response shall be provided in accordance with the specific corrective action document requirements.

INSPECTION AND ACCEPTANCE (ADDITIONAL PROVISIONS)

Inspection may be accomplished at any work location involved and authorized government personnel shall be permitted to observe the work or to conduct inspection at all reasonable hours. Inspection or test by the Government of any services rendered or supplies furnished hereunder does not relieve the Contractor from any responsibility regarding defects or other failures to meet contract requirements which may be discovered prior to final acceptance by the Government.

CLAUSES INCORPORATED BY FULL TEXT

52.209-4 FIRST ARTICLE APPROVAL--GOVERNMENT TESTING (SEP 1989) (Contracting Officer shall insert details)

(a) Once the contract is awarded, the first Delivery Order shall constitute as a “First Article" Approval Test Order. The Contractor shall deliver each unit(s) within the specified delivery period, and deliver all items to the Government at Habitability material Staging Center, cited in the order for first article tests. The scope of the first article tests shall be visual and dimensional inspection, and review of documentation. The inspection will be non-destructive and all approved materials will be fully utilized in a shipboard project. The shipping documentation shall contain this contract number and the Lot/Item identification. The characteristics that the first article must meet and the testing requirements are specified elsewhere in this contract.

(b) Within 20 calendar days after the Government receives the first article, the Contracting Officer shall notify the Contractor, in writing, of the conditional approval, approval, or disapproval of the first article. The notice of conditional approval or approval shall not relieve the Contractor from complying with all requirements of the specifications and all other terms and conditions of this contract. A notice of conditional approval shall state any further action required of the Contractor. A notice of disapproval shall cite reasons for the disapproval.

(c) If the first article is disapproved, the Contractor, upon Government request, shall submit an additional first article for testing. After each request, the Contractor shall make any necessary changes, modifications, or repairs to the first article or select another first article for testing. All costs related to these tests are to be borne by the Contractor, including any and all costs for additional tests following disapproval. The Contractor shall furnish any additional first article to the Government under the terms and conditions and within the time specified by the Government. The Government shall act on this first article within the time limit specified in paragraph (b) of this clause. The Government reserves the right to require an equitable adjustment of the contract price for any extension of the delivery schedule or for any additional costs to the Government related to these tests.

(d) If the Contractor fails to deliver any first article on time, or the Contracting Officer disapproves any first article, the Contractor shall be deemed to have failed to make delivery within the meaning of the Default clause of this contract.

(e) Unless otherwise provided in the contract, the Contractor-- (1) May deliver the approved first article as a part of the contract quantity, provided it meets all contract requirements for acceptance and was not consumed or destroyed in testing; and (2) Shall remove and dispose of any first article from the Government test facility at the Contractor's expense.

(f) If the Government does not act within the time specified in paragraphs (b) or (c) of this clause, the Contracting Officer shall, upon timely written request from the Contractor, equitably adjust under the Changes clause of this contract the delivery or performance dates and/or the contract price, and any other contractual term affected by the delay.

(g) The Contractor is responsible for providing operating and maintenance instructions, spare parts support, and repair of the first article during any first article test.

(h) Before first article approval, the acquisition of materials or components for, or the commencement of production of, the balance of the contract quantity is at the sole risk of the Contractor. Before first article approval, the costs thereof shall not be allocable to this contract for (1) progress payments, or (2) termination settlements if the contract is terminated for the convenience of the Government.

(i) The Government may waive the requirement for first article approval test where supplies identical or similar to those called for in the schedule have been previously furnished by the Offeror/Contractor and have been accepted by the Government. The Offeror/Contractor may request a waiver.

(j) The Contractor shall produce the first article and the production quantity at the same facility.

(End of clause)

52.205-4 Addendum

FIRST ARTICLE APPROVAL

The characteristics that the first article must meet and testing requirements are in accordance with paragraph 4.1.1 of MIL-PRF-32038 except as follows:

(a) Shock (paragraph 3.53). There are no shock test requirements

(b) Load Tests (paragraphs 3.6.1 through 3.6.9). Load testing is not required for a units made in accordance with the invoked drawing without any deviation.

(c) The first article shall include copies of material certifications and source documentation.

First article tests conducted by the Government will be primarily visual and dimensional inspections and shall be accomplished using tape measures and vernier calipers. The Government may also perform additional tests and inspections in accordance with MIL-PRF-32038.

For items with MIL-PRF-32038 Performance Specifications Sheets, dimensions shall be compared to dimensional requirements cited in MIL-PRF-32038 and the applicable Performance Specifications Sheet. For those items for which there is no MIL-PRF-32038 Performance Specifications Sheet, dimensions will be compared to dimensional requirements cited in MIL-PRF-32038 and the drawing cited in the Contracts Line Item Description.

The Contractor shall produce both the first article and the production quantity at the same facility and shall submit a certification to this effect with each first article.

TECHNICAL POINT OF CONTACT (TPOC)

A. The Technical Point of Contact (TPOC) for this contract is:

(1) Mr. Baldev Gill

(2) Mid Atlantic Regional Maintenance Center (MARMC)

(3) Bldg. LF-18, (Code 226) (4) 9727 Avionics Loop

(5) Norfolk, Virginia 23511

(6) Phone: (757) 443-3872, x1856

(7) baldev.gill@navy.mil B. Alternate TPOC's may be designated by delivery order (there may be more than one alternate TPOC).

C. The TPOC will act as the Contracting Officer's Technical Representative for technical matters. The TPOC will provide technical direction and discussion as necessary with respect to the specification or statement of work, as well as monitoring the progress and quality of contractor performance. The TPOC is not an Administrative Contracting Officer and does not have the authority to direct the accomplishment of effort which is beyond the scope of the statement of work in the contract (or task order).

D. When, in the opinion of the contractor the TPOC requests outside the existing scope of the contract (or task order), the contractor shall promptly notify the contracting officer (or ordering officer) in writing. No action shall be taken by the contractor under such direction until the contracting office has issued a modification to the contract (or in the case of a task order, until the ordering officer has issued a modification to the task order) or until the issue has otherwise been resolved.

E. In the event that the TPOC named above is absent due to leave, illness, or official business all responsibilities and functions assigned to the TPOC will be the responsibility of an alternate TPOC. The alternate Technical Point of Contact may be identified in Delivery Orders.