SOW_1-23-2018.doc

Navy Exchange Service Command, Code A3 3280 Virginia Beach Blvd., Virginia Beach, VA 23452-5724

USS DWIGHT D EISENHOWER

CVN-69

HABITABILITY IMPROVEMENT SPECIFICATION

BARBER SHOP

(02-195-6-L)

201708-B 1.0

GENERAL REQUIREMENTS AND SPECIFICATIONS

1.1 The ship will be responsible for the following:

1.1.1 Providing fire watches for all hot work to be performed.

1.1.2 Making available electrical power and/or ship’s service air to contractor’s equipment that is operationally compatible with the ship’s systems

1.1.3 Providing stowage for the contractor’s tools and equipment during the installation.

1.1.4 Providing temporary ventilation as required during installation. This shall include connection of the vent hose to the blower and installation of the blower shall be outside of the compartment if flammable or explosive materials are being used in the installation or removal.

1.1.5 Disconnecting and reconnecting all electrical equipment, piping, drains, steam supply lines, etc., if equipment has to be temporarily removed during the performance of the contract. Making all connections to ship’s power source or service supply for new equipment installation.

1.1.6 Labeling of all compartment identifications, power sources, and service supplies.

1.1.7 Working with the contractor to make timely decisions on material selections (color, pattern, style, etc.), solve interference problems, and ensure access to the ship and work areas.

1.2 The contractor shall comply with the following:

1.2.1 This specification is based upon the following requirements whose provisions shall prevail in areas where this specification is silent:

A. NAVSEA S9AA0-AB-GOS-010/GSO, “General Specifications For Overhaul Of Surface Ships” B. NAVSEA 59AA0-AB-GOS-030 SUPPLEMENT, “General Specifications For Ships With The Aegis Addendum” C. NAVSEA 0902-LP-018-2010, “General Overhaul Specifications For Deep Diving SSBN/SSN Submarines”

D. NAVSEA 0924-062-0010, “Submarine Safety (SUBSAFE) Requirements Manual”

E. NAVSEA Standard Items

1.2.2 Where drawings or specifications are referenced herein, the latest revision/amendment of such drawing or specification in effect upon date of award of contract shall be applicable, unless otherwise specifically noted.

1.2.3 Contractors shall obtain from sources designated as repositories, copies of standard navy drawings, referenced specifications, and standards which are part of the DOD Index of Specifications and Standards (DODISS). Other required references should be made available for examination at a designated location.

1.2.4 Unless otherwise noted in the purchase document, the contractor shall be responsible for all requirements as applicable to the type of supply and/or service being provided. The government shall rely on contractor expertise for final design and fabrication of items. The design emphasis is encouraged to have modern, eye appealing characteristics that conform to the general requirements specified herein.

1.2.5 Prior to material delivery or installation, the contractor, when requested by the contracting officer, shall provide the ship and the contracting officer with a written certificate of conformity from the contractor, stating that the materials procured for installation meet applicable NAVSEA specifications. If a certificate of conformity is not requested, then the contractor shall be deemed to be self-certifying and shall be solely responsible for compliance with NAVSEA specifications.

1.2.6 All materials procured/installed shall be in accordance with Military Specification MIL-STD-1623 Fire Performance Requirements and Approval Specifications for Interior Finish Materials and Furnishings (Naval Shipboard Use).

1.2.7 The contractor shall meet with the ship’s representative as soon as possible after award of contract/delivery order to identify and select all finish materials (i.e. HPPL, fabrics, etc…). The contractor shall provide the ship with catalogues and/or samples of shipboard approved materials from which the ship may select their desired and alternate patterns and colors. The contractor shall verify the availability of the selected item with their suppliers and notify the ship as soon as possible when a material is found to be unavailable. When a change in material selection is required the contractor shall get with the ship as soon as possible to remedy the situation. The contracting officer/purchaser shall be notified of all changes.

1.2.8 The contractor shall not interfere with the daily routine of the ship.

1.2.9 The contractor shall be responsible for his own measurements. Template work from ship and equipment, as required. All sizes stated are approximate. Furnishings manufactured for knockdown construction must be capable of passing through surface ship access (26” x 66”) or submarine access (26” diameter). Furnishings may be fabricated and assembled at installation site. Whichever method is employed, it must first be consistent with accepted shop practices. The ship’s representative shall furnish dimensions not specified herein.

1.2.10 Unless specifically stated herein, the contractor shall be responsible for providing and connecting all wiring, piping, drain lines, etc. to the new item/equipment being installed by the contract. The contractor shall provide wiring, piping, etc. In sufficient lengths to run from the newly installed item to the nearest available ship’s force approved existing point of connection. Ship’s force shall be responsible for all actual connections to ship’s power or other systems service supply. The contractor shall be totally responsible for ensuring that each item installed, is fully functional, and operates in accordance with the intended design, and within the intended capabilities or limitations of the specific piece of equipment.

1.2.11 The contractor shall be responsible for replacing any item installed or re-installed under the requirements of the contract/delivery order, if the item is deemed to be defective, inoperative or incapable of performing as designed.

1.2.12 Where cadmium plating is specified on referenced drawings, the requirement shall be replaced with the use of zinc plating in accordance with ASTM-B633, Service Condition SC3, Type I. Coating thickness shall be 12 microns (approximately 0.0005 inches).

1.2.13 Patch/repair insulation (thermal and acoustic) damaged incidental to work shown herein including surfaces affected by welding. Installations shall be in accordance with NAVSEA Tech Manual S9086-VH-STM-010/Chapter 635, Thermal, Fire, And Acoustic Insulation; material shall match surrounding area except that a NAVSEA approved mineral wool shall be used in lieu of ceramic fiber for patching of fire insulation.

1.2.14 Touch-up/repair deck covering damaged incidental to work shown herein including adjacent surfaces affected by welding. Work shall be in accordance with NAVSEA Tech Manual S9086-VB-STM-000/Chapter 634, Deck Coverings; color to be determined by ship’s representative. Work shall include surface preparation and underlayment specified by this tech manual.

1.2.15 The contractor shall be responsible for complying with all safety requirements as specified by OSHA, the industrial activity and the Ship’s Safety Officer. In the event of a conflict, the ships safety requirements shall take precedence.

1.2.16 Where permanent removals are specified in the contract, contractor shall remove the items from the ship and turnover to ship’s representative on pier unless otherwise stated.

1.2.17 Where the terms renovate, refurbish, repair, or renew are used herein to apply to a degree of work to be accomplished for a specific item, the terms shall mean that the item is to be restored to a like-new condition. This shall mean that any components of the item which are necessary to the structural integrity of the item are to be repaired, if practicable, or replaced with new components if needed. Any internal, external, or ancillary components of the item, which are pertinent to the functioning of the item shall be repaired or replaced to ensure that the item performs in accordance with the intended design and within the items capabilities and limitations. In the absence of specific reference to cosmetics, the decorative or protective surfacing of the item shall be removed and similar new surfacing shall be installed, unless the existing surfacing is non-approved material or has been applied in a non-approved manner. In such case, the new surfacing material and the method of installation will be specified. Preparation of the existing surface and installation of the new surfacing shall be accomplished in accordance with gen specs sections 631 unless otherwise stated.

1.2.18 The contractor shall be responsible for all interference removals/installations incident to specified work unless otherwise stated.

1.2.19 Sizes of hold down fasteners are determined from manufacturers drawing. Due to manufacturers’ changes and contract awards, actual equipment received for installation may vary from that originally designed for. Therefore, template exact size, length, and location of hold down fasteners to suit. If bolt sizes are changed, the material type and grade are to remain the same.

1.2.20 Install flashing to seal off areas, which are, inaccessible for cleaning.

1.2.21 Items being removed and re-installed are to be tagged with a tag number showing compartment number, frame number, port or starboard location, and held for re-installation as noted in this specification.

1.2.22 Items shall be removed with supporting components (mounting hardware, sub-base, etc.) And held for re-installation by this specification. Replace any damaged supporting component with similar material.

1.2.23 Paint new/existing items as identified in this specification (furniture, trim, doors, etc.) And touch-up existing paint damaged incidental to work shown herein including adjacent surfaces affected by welding. Painting shall include surface preparation and shall be in accordance with NAVSEA Tech Manual S9086-VD-STM-010/020/030, CH 631 V1, V2, V3, Preservation Of Ships In Service (surface preparation and painting). The required paint formulas (number of coats, etc.) are specified in Chapter 631-1-3, V1 of this tech manual. Finished color to be determined by ship’s representative.

1.2.24 Treat faying surfaces between dissimilar metals in accordance with section 8.2.9 of NAVSEA S9086-VD-STM-030/Chapter 631 V3, Preservation Of Ships In Service (Surface Preparation and Painting).

1.2.25 Fabrication, welding, and inspection shall be in accordance with MIL-STD-1689A (SHIPS).

1.2.26 The contractor is responsible for providing gas-free certification for all areas and adjacent areas in which hot work (welding, burning, etc.) Or toxic hazardous installations are to be performed.

1.2.27 Remove insulation and deck covering in way of work shown herein including far side of bulkheads/decks affected by welding. All removals shall be reinstalled/replaced after hot work is completed.

1.2.28 All sharp or rough edges and corners that present a possible source of injury to personnel or damage to equipment shall be rounded off by grinding or other mechanical means to provide a smooth surface.

1.2.29 Install all furnishings and equipment level and/or plumb with baseline of ship.

1.2.30 The contractor is responsible for the cleanliness of the working area. The contractor shall remove all trash/debris caused by the contractor as a result of the removals/installations specified herein from the ship, at the end of each workday.

1.2.31 Cribbing for joiner bulkheads shall be installed as required. Install cribbing in accordance with NAVSEA Drawing 804-5000991. Cribbing members shall be capable of being removable and/or reusable. Connections shall be bolted in lieu of welded. (If existing cribbing installation is welded type connections, then new portion of cribbing may be installed in a similar manner.) Install from deck to overhead. Provide and install upper and lower retainer strips.

1.2.32 Where high pressure plastic laminate (HPPL) is required, it shall be in accordance with Military Specification MIL-P-17171. For bulkhead installations it shall be Type IV, installed in accordance with NAVSEA Drawing 804-5000991. All other uses, such as laminating material for cabinets, tables, etc. shall require Type I. Adhesive in accordance with Specification A-A-1936 (supersedes M-M-130) shall be used to bond the HPPL to aluminum. Comply with Gen Spec 637.

1.2.33 Remove and scrap existing label plates superseded by new label plates.

1.2.34 Repair damage to ship’s structure, caused by work shown herein, with material identical to adjacent structure. Where welds are performed on bulkheads, decks and overheads the opposite side of where welding occurs shall be checked on for damage and repaired as necessary.

1.2.35 Unless otherwise specified, items installed herein may be shifted slightly to clear minor interferences. The notation “min. (typ)” next to dimensions on in this specification indicates the item(s) shall be installed as close as practical to ship’s structure, vent, piping, etc. Abbreviations are in accordance with MIL-STD-12D except as follows:

(R/T) = Removed & turn over to ship on pier (/////////)

(E) = Existing

(R/R) = Remove & Relocate

(M) = Modified

(R/I) = Remove & Install

(N) = New

1.2.36 Use backing plates/sway-bracing/cantilever supports when attaching furnishings to bulkheads/overheads or furniture to provide reinforcement.

1.2.37 Template exact location of mounting bolts from equipment.

1.2.38 Furniture items shall be secured to the deck or bulkhead in accordance With General Specifications Section 640 And NAVSHIPS Drawing Number S3306-921770; Sub-Bases And Clips, Shipboard Furniture and/or NAVSEA Drawing Numbers 612-2121710/2121711; Misc Furniture Details.

1.2.39 Furniture item numbers referred to herein may indicate a specific furniture item described in the U.S. Navy Shipboard Furniture Catalog (SFC); NAVSEA S9600-AD-GTP-010. The NAVSEA Drawing numbers for fabrication of furniture items is given when available. All furniture items shall be fabricated using aluminum structural components (i.e. angle, tubing, etc.)

A. MIL-PRF-32038, “Shipboard Furniture, Fixtures, Fittings, And Accessories, General Specifications For" (Supersedes MIL-F-243 “Shipboard Furniture, Steel” and MIL-F-902, “Shipboard Furniture, Aluminum”)

B. NAVSEA Drawing 803-5959310/A, “Furniture Construction Details”

C. NAVSHIPS Drawing S3200-860055, “Hardware For Metal Furniture”

D. NAVSHIPS Drawing 612-2121710/1, “Misc Furniture Details”

E. NAVSHIPS Drawing 805-1632368, “Metal Furniture Construction”

1.2.40 Cushioning needed in fabrication of furniture items shall be polychloroprene (neoprene) in accordance with Mil Spec MIL-PRF-20092, Type II, Class 5.

1.2.41 Where vinyl covering material is specified for furniture covering, it shall meet the requirements of Specification A-A-2950, (supersedes Fed Spec CCC-A-680, Class 2, Treatment (A/1))

1.2.42 Where fiber upholstery fabric covering material is specified for furniture covering or re-upholstering, it shall meet the requirements of MIL-STD-1623. The material used shall be aromatic polyamide (polyaramid). An alternative to the polyamarid, is aramid and aramid/novaloid blend in accordance with MIL SPEC MIL-C-24500 Type I with a minimum weight of 6 ounces per square yard. Polyaramid is preferred for furniture covering.

1.2.43 The construction requirements (stitching, edge locking, thread, etc…) for both types of upholstery coverings (vinyl and fiber) shall be in accordance with Specification A-A-59473, (supersedes Mil Spec DOD-C-24556).

1.2.44 Furniture items specified herein with the right or left arm designations shall mean the arm of the item to the viewer’s right or left when viewed from the back of the furniture item.

1.2.45 All electrical power and lighting modifications incidental to work specified herein shall be procured/installed in accordance with NAVSEA Drawing 53711-803-5184170, Rev. K – Lighting For Naval Ships (DOD-HDBK-289) and as follows:

A. Receptacles shall meet W-C-596/12 or hospital grade.

B. Switches shall meet W-S-896/2 or hospital grade.

C. Cover plates shall UL 514A (supersedes W-P-455).

D. Contractor to bid on size cabling to suit ships electrical system and/or equipment to be installed. Cabling/wiring shall meet MIL-C-24643/15 (LSDG4).

E. Decorative conduit shall be “Wiremold Surface Raceway System” Model V500 (Steel) available from Electrical Suppliers Inc., Norfolk, VA, phone (757) 855-3031 or equal.

1.2.46 Where installation of storefront showcases and ship store/barbershop access doors is required, these items shall be installed with huck rivets: ¼” dia. Button head with “MSC” collars on 12” centers and each at corner and middle of item, install ¼”-20 UNC button head bolts with nylon lock nuts.

1.2.47 Deck coverings:

1.2.47.1 Decks where installation of cosmetic polymeric (monolithic seamless) deck covering (PRC) is required. Remove existing deck covering down to bare metal surface. Prepare and prime deck surface in accordance with General Specification Section 631. Underlay shall be used to slope deck for proper drainage. Where underlay is required it shall conform to Mil Spec MIL-PRF-3135 (supersedes MIL-D-3135), Type 1, Class 2. Install new cosmetic polymeric (monolithic seamless) deck covering material throughout entire areas specified. Deck covering to be in accordance with Mil Spec MIL-PRF-24613 (supersedes MIL-D-24613). Manufacturers of the material are listed in Qualified Products List QPL 24613. “Products Research Corp.” is an approved source.

Note: Installation of new deck covering material shall be in accordance with manufacturers’ specifications and detailed requirements stated in Gen Specs Section 634. Install to a thickness not to exceed ¼ inch. Install with cove base effect to extend vertically for approximately 3 inches up onto the compartment boundary bulkheads. Cove base effect shall be at the discretion of the ships representative and areas requiring it shall be identified prior to commencement of work. Apply a sealer coat to complete the installation.

1.2.47.2 “Stratica” tile shall be installed in accordance with the manufacturers recommended instructions and the NAVSEA Task Group Instruction (TGI) 634-63421-008, dated 2JUN 00.

1.2.47.3 All other decking material types shall be installed in accordance with NAVSEA Technical Manual S9086-VG-STM-010, Chapter 634.

1.2.47.4 Carpeting shall be installed on top of existing, undamaged underlay material. Underlay material shall be repaired as required in accordance with NAVSEA Technical Manual S9086-VG-STM-010, Chapter 634.

1.2.48 Where polycarbonate material is specified for mirror/transparent designs it shall be fabricated from sheets conforming to specification MIL-P-46144C, Type III, Class 1, Grade A and exhibit the following salient characteristics.

Transparent Designs

A. Polycarbonate plastic sheet shall be natural color (colorless and transparent)

B. Mirror thickness shall be as specified. Fully fabricated mirrors shall have beveled edges, radius corners and pre-drilled holes for mounting.

C. The mirrored surface shall be coated with silver argent and a 0.2 TO 0.6 mil protective coating applied over the silver argent.

D. The finished mirror shall produce minimal reflective image distortion.

E. Heavy paper masking identifying material shall be applied to all exposed surfaces for protection and shall be removed by contractor after ship’s force verification and before acceptance.

NOTE: Commercially available polycarbonate is acceptable. The material shall be similar to polycarbonate manufactured by General Electric (GE). The polycarbonate shall be Type III (mar resistant), Class 1 (ultraviolet stabilized), Grade A (high abrasion resistant) as defined in Mil Spec MIL-P-46144 Rev C. Polycarbonate has previously been manufactured and tested in accordance with the above specification; Rev B. Revision c of the specification has imposed additional testing criteria. The manufacturers of polycarbonate do perform product testing to verify that the product conforms to the specification. However, because of the stringent testing requirements of Rev C, manufacturers will not provide certification that their product meets all requirements.

NOTE: Measurements provided herein are approximations and contractor is responsible for making all measurements to ensure a professional, well-fit product placement.

SECTION 2 – SCOPE OF WORK

Period of Performance: 28 February 2018 – 13 April 2018 Accomplishment of this requirement shall be in accordance with the Habitability Equipment Procurement Policy dtg R 181130Z JUN 14.

The Contractor is to furnish all labor and materials, remove any existing items, manufacture and/or procure and install the following materials where indicated.

PAYMENT INFORMATION

METHOD OF PAYMENT

Payment will be IAW the Prompt Payment Certification (PPC) Program.

The Prompt Payment Act (PPA) requires payment to contractors no earlier than seven days in advance of the traditional 30-day deadline. If a proper invoice is received with all required supporting documents, vendors can expect to receive payment by the traditional 30-day deadline or by the payment terms in the contract. The proper documentation is a valid contract, invoice, receiving report and the necessary contract obligation (funding) posted within the proper accounting system.

Vendors can assist in providing valid invoices by ensuring the address in the invoice is the same address the payment should be sent to and following up with the correct financial point of contact (POC) identified in the contract.

ATTN: INVOICE “TO” ADDRESS

JOHN SCHMALZ

(757) 443-2524

JOHN.SCHMALZ@NEXWEB.ORG

FINANCIAL POC: JOHN SCHMALZ, (757) 443-2524

EMAIL: JOHN.SCHMALZ@NEXWEB.ORG

FINANCIAL POC: GENE HOFFMAN, (757) 502-7472

EMAIL: GENE.HOFFMAN@NEXWEB.ORG

2.1 DOOR/FRAME.

Remove existing door and frame. Provide and install new door with aluminum frame. Door to be approximately 26” W x 6’-4”H with a 2” frame. Door to be pre-hung unit constructed of anodized aluminum framework with a 3/8” thick polycarbonate or tempered safety glass door panel. Door shall be configured and installed inside bulkhead opening. Door shall ‘open in’ and be equipped with a center push bar. Door shall be similar to type furnished by Walker LaBerge Company, Norfolk, VA. or equal. NOTE: Contractor to measure door size, openings and, interferences to ensure proper installation. Utilize Huck Magna Grip Fastening System with “Button-Head and MGC Collars”. Equip with door closure.

2.2 BARBER CHAIR.

2.2.1. Provide and install a new barber chair from S9600-AD-GTP-010 (US Navy Shipboard Furniture Catalog). http://usnhabeqptcatalog.gdit.com/ Mount new chair to the deck. Preparation of the existing surface and installation of the surface shall be in accordance with GEN SPEC section 631. Contractor will ensure that chair shall be capable of rotating 360 degrees and, be capable of being locked in place. Hydraulic unit providing for chair elevation shall be completely sealed. Provide with sub-base for ease of replacement. Cushioning material shall be polychloroprene and covering material shall be vinyl. When space planning and prior to installation of chairs, it should be noted that the pivot point of the chair is asymmetrical of the longer axis of the chair.

The color of the new barber chair covers to be determined by ship’s representative. Source of new chair and replacement parts: Turnbull Enterprises, Inc. 3635 Benson Ave. Baltimore, MD. 21227, (301) 644-8282.

2.2.2. Reposition and remount existing chairs to increase chair turning radius and eliminate interference with adjoining chairs. Preparation of the existing surface and installation of the surface shall be in accordance with GEN SPEC section 631. Provide chairs with sub-base for ease of replacement.

2.2.3 Refurbish and recover seven (7) barber chairs to “like-new” condition. Barber chair shall be refurbished to a “like-new” condition. Where the terms “renovate” or “renew” are used herein, apply to a degree of work to be accomplished for a specific item, the terms shall mean that the item is to be restored to like-new condition. This shall mean that any components of the item, which are necessary to the structural integrity of the item shall be repaired, if practicable, or replaced with new components if needed. Any internal, external or ancillary components of the item which are pertinent to the functioning of the item shall be repaired or replaced, to ensure that the item performs in accordance with the intended design and within the items capabilities and limitations. Upholstery color / pattern to be sports themed or as selected by ships representative.

2.3 DECK COVERING (MONOLITHIC SEAMLESS DECKING).

Remove existing deck covering material. Provide and install approximately 640 square feet of new monolithic seamless deck covering (PRC). Prepare and prime deck surface in accordance with GEN SPEC section 634. Install new underlay conforming to Mil SPEC MIL-D-3135 in accordance with GEN SPEC section 634. Metal decks beneath the underlay shall be primed as specified in GEN SPEC section 631. Install new Cosmetic Polymeric (Monolithic Seamless) deck covering throughout. Deck covering shall be in accordance with MIL SPEC Mil-D-24613, Type II, Class 2. Install to a thickness not to exceed ¼ -inch. Install in accordance with manufacturers’ instructions. Apply sealer coat to complete the installation. See Qualified Products List (QPL 24613) for a listing of approved manufacturers or suppliers. Ship’s representative shall determine color/patterns.

2.4 BARBER COUNTERS.

Remove existing barber counters. Provide and install seven (7) new commercial barber counters. Counters to be approximately 54” L x 18” D x 41” H. Counter units to be fabricated of aluminum frame construction. Provide and install football locker room style storage lockers at each end of the counters. Fabricate and install units as indicated on the attached sketch. Provide cabinets with lockable drawers and vacuum storage. Provide continuous top lengths where practicable to minimize the amount of joints required. Top surface of counter units are to be stainless steel. Exposed surfaces are to be covered with High Pressure Plastic Laminate (HPPL) in accordance with MIL-P-17171, Type I. Ships force to select color / pattern. Interior of cabinet to be painted in accordance GEN SPEC section 631. Provide unit with sub-base in accordance with NAVSHIPS DWG. S3306-921770 and GEN SPECS section 640.

SFC No. B-8A-2 or equal.

NOTE: Furniture must be fabricated in lengths capable of passing through an opening 26 x 66 inches with rounded eight-inch radius corners. Contractor shall ensure sufficient electrical cable runs to support lights, and shall provide sufficient 120V outlets for electric clippers, etc. Prior to fabrication of barber counters, verify size and, that new sink will install into the counter.

2.5 SINKS AND FIXTURE FITTINGS.

Remove existing sink and fixtures. Provide and install seven (7) new sinks and bar type gooseneck fixture fittings. The sinks shall be supplied with hot and cold potable water. Sink shall be similar to type furnished by ELKAY Mfg. Co. of Oak Brook, ILL. Model No. LLVR-1916, or equal. Fixture and fittings shall be in accordance with MIL-F-163. Provide maintenance access to plumbing fixtures below sink.

2.6 MIRRORS.

Remove existing mirrors. Provide and install seven (7) new mirrors. Mirror to be approximately 36” H x 42” W. Mirrors shall be ¼” inch thick, laminated safety glass with mirrored backing. Provide the mirrors with an aluminum frame. Contractor shall ensure a stable, sturdy item, which shall be secured to the bulkhead in such a way as to prevent it from falling. Provide a fluorescent or LED lighting fixture above mirror. Provide light fixture with a diffusing panel and angle fixture down towards working area. Lighting should provide an average of 42 footcandles of illumination to the barber chair. Verify sizes with ship’s representative prior to fabrication. SFC No. B-2B-2, or equivalent.

2.7 BENCH WITH STORAGE.

Provide and install new bench approximately 48”’ L x 19” H x 19” DV, with stowage beneath seat. Fabricate bench of aluminum frame construction. Fabricate aluminum bench seat with aluminum angle lip to hold neoprene cushion seat with vinyl upholstery cover. Provide seat with hinges to allow access to storage area, below seat. Provide with a neoprene cushion seat with vinyl upholstery cover. Provide with a back cushion, attached to the bulkhead. R-20092 Type II, Class 5, covered with vinyl upholstery material in accordance with FED SPEC CCC-A-680, Class 2, treatment (a, 1). Back cushion and seat shall be polychloroprene cushioning in accordance with MIL SPEC MIL-All. Seat shall be hinged at top with piano type hinge with Cres pin. All exposed surfaces shall be covered with HPPL in accordance with MIL-P-17171, Type I. Adhesives to be in accordance with MMM-A-130. Provide with a Sub-Base, secure to deck and bulkhead. The color of the new seat cushion and HPPL to be determined by ship’s representative.

SFC No. B-3F-1, or equivalent.

2.8 BENCH SEAT.

Provide existing bench seat with new seat tops, hinged to allow access to storage area, below seat. Provide with a neoprene cushion seat with vinyl upholstery cover. Provide with a back cushion, optionally, attached to the bulkhead. R-20092 Type II, Class 5, covered with vinyl upholstery material in accordance with FED SPEC CCC-A-680, Class 2, treatment (a, 1). Back cushion and seat shall be polychloroprene cushioning in accordance with MIL SPEC MIL-All. Seat shall be hinged at top with piano type hinge with Cres pin. All exposed surfaces shall be covered with HPPL in accordance with MIL-P-17171, Type I. Adhesives to be in accordance with MMM-A-130. Provide with a Sub-Base, secure to deck and bulkhead. The color of the new seat cushion and HPPL to be determined by ship’s representative.

SFC No. B-3F-1, or equivalent.

2.9 STORAGE LOCKER

Provide and install one (1) new 48”W x 18”D x 72”H gear locker, where indicated on the attached drawing. Gear locker shall be fabricated similar to Shipboard Furniture Catalog item no. 7C-1, HTD 805-1629991. Fabricate of aluminum frame construction. All exposed surfaces shall either be painted or covered with High Pressure Plastic Laminate (HPPL) and the interior shall be painted in accordance with GEN SPEC Section 631. Provide with adjustable shelves and doors. Doors shall have continuous hinge and associated hardware, and capable of being locked.

SFC No. B-8A-1, or equivalent.

2.10 TRASH / RECYCLE STATION

Provide and install one Trash / Recycle station where indicated on drawing. Fabricate of aluminum frame construction. All exposed surfaces shall either be painted or covered with High Pressure Plastic Laminate (HPPL). Ship to select color / pattern. The top to have three circular openings. Center section to have hinged doors for access to trash cans. Fabricate unit to be approximately 72” W x 24” D x 36” H. The top is to be three separate hinged lids.

2.11 FRAMED POSTERS

Provide and mount sports themed posters. Each to be approximately 60” H x 72” W, or as determined by ship’s representative and measurements taken at exact locations.

2.12 FALSE OVERHEAD AND LIGHTING

Remove all false overhead ceiling tiles and grid work suspending the ceiling. Remove all supports specific to the false overhead. The intent is to restore the overhead to the original, as-built, condition. Replace and mount lighting fixtures to original design. Clean and paint the overhead to the color specified for ship.

2.13 OFFICER / CPO BARBER SHOP

2.13.1 Provide and install a new barber chair from S9600-AD-GTP-010 (US Navy Shipboard Furniture Catalog). http://usnhabeqptcatalog.gdit.com/ Mount new chair to the deck. Preparation of the existing surface and installation of the surface shall be in accordance with GEN SPEC section 631. Contractor will ensure that chair shall be capable of rotating 360 degrees and, be capable of being locked in place. Hydraulic unit providing for chair elevation shall be completely sealed. Provide with sub-base for ease of replacement. Cushioning material shall be polychloroprene and covering material shall be vinyl. When space planning and prior to installation of chairs, it should be noted that the pivot point of the chair is asymmetrical of the longer axis of the chair.

2.13.2 Remove the bench seat in the Officer/CPO barber shop. Restore bulkhead, to include painting, as needed. Provide and install two shipboard quality chairs. Use Item No. B-3B-2, Class 1, from the Shipboard Furniture Catalog. Ship’s force to select color. Installation shall be such that the chairs are “rigged for sea”.