This is a combined synopsis/solicitation for commercial items prepared in accordance with

Federal Acquisition Regulation (FAR) Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation that Naval Surface

Warfare Center Carderock Division (NSWCCD) intends to issue and is a Request for Quotes

(RFQ) for the following Supplies and/or Services.

Naval Surface Warfare, Carderock Division (NSWCCD), has procurement request for the diagnostics and repair of two (2) Hamilton Jet waterjet propulsion units (specifically

HJ322/HJ292)

The provisions and clauses included and/or incorporated in this solicitation document are those in effect through the Federal Acquisition Circular. This RFQ incorporates all provisions and clauses in effect through Federal Acquisition Circular FAC 2026-01 effective 03/13/2026 located on https://www.acquisition.gov/?q=browsefar and the Defense Federal Acquisition Regulation

Supplement (DFARS) DPN 20260507 effective 05/07/2026 located at https://www.acq.osd.mil/dpap/dars/change_notices.html. SEE ATTACHED SOLICITATION

FOR CLAUSES AND PROVISIONS. The NAICS code is 333618 and the associated PSC code is 2940/R425. NOTE: A Class Waiver is not applicable to procurement unless the NAICS code, PSC, and NAICS Code Descriptor currently in effect, match the item(s) being procured. This procurement IS being set aside for small businesses.

Interested parties may identify their interest in this requirement by submitting a quote and/or capabilities statement no later than 11:30 AM on July 23, 2026. It is anticipated that one firm-fixed price purchase order will be issued in response to this RFQ.

All responses shall include the following.

1. Quote on company’s Letterhead

2. Pricing

3. Cage Code

4. FOB Destination

5. Point of contact

6. GSA contract number (if applicable)

7. Business Size

8. Quote should be rounded off to the nearest whole dollar

Each response must clearly indicate the capability of the quoter to meet all specifications and requirements. There will be no additional CLINs added for shipping. If there is a shipping charge, please include in the price.

Responses to this notice are due on or before 11:30 AM on July 23, 2026, Eastern Daylight Time

(EDT) to christopher.c.rolince.civ@us.navy.mil.

Point of Contact for this notice is Chris Rolince, 757-513-7247, christopher.c.rolince.civ@us.navy.mil https://www.acquisition.gov/?q=browsefar https://www.acq.osd.mil/dpap/dars/change_notices.html mailto:christopher.c.rolince.civ@us.navy.mil mailto:christopher.c.rolince.civ@us.navy.mil

Solicitation/Contract Form Continuation

Hamilton Water Jet Repairs

N0016726Q1131

Continuation of Supplies or Services and Prices/Costs

Additional Information/Notes

Item Supplies/Service Quantity Unit Unit Price Amount

0001 Troubleshooting & Transportation

Pricing Arrangement: Firm Fixed Price

1 Lot

Water Jet Maintenance Kit

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

Internal Number: 1024143001 Pricing Arrangement: Firm Fixed Price

1 Each

Continuation of Description

PERFORMANCE WORK STATEMENT (PWS)

11MRX Hamilton Jet Diagnostics and Repair

1.0 DESCRIPTION OF SERVICES/INTRODUCTION: NSWCCD has a requirement for the diagnostics and repair of two (2) Hamilton Jet waterjet propulsion units (specifically HJ322/HJ292) and their integrated Blue Arrow advanced electronic control systems aboard quantity two (2) 11-meter (11M) crafts located at Naval Base Guam, USA.

2.0 BACKGROUND: The 11-Meter Rigid Inflatable Boat (11M RIB) relies on the integration of high-performance diesel engines and twin Hamilton Jet waterjets to conduct high-speed, high-maneuverability tactical missions. To maximize maneuvering safety and ease of docking, these crafts are equipped with the Hamilton Jet Blue Arrow electronic control system. The Blue Arrow system utilizes a dual-redundant 24VDC CAN bus microprocessor network to tie the helm station devices--including the multi-axis Mouse Boat controller--directly to the Jet Interface Modules. Due to the high complexity of digital fly-by-wire and hydraulic interfaces, marine technicians shall utilize specialized software and proprietary protocols to isolate electrical faults, resolve calibration drift, and perform system autotuning.

3.0 OBJECTIVE: The objective of this contract is to maintain, diagnose, troubleshoot, calibrate, and repair the physical Hamilton Jet waterjets and the integrated Blue Arrow electronic control systems to include travel to and from the location referenced in Section 1.0. This scope specifically includes below and contractor shall perform the following:

3.1 Electronic Scanning & Fault Code Diagnostics: Establishing direct communication with the Blue Arrow onboard microprocessors using licensed PC-based software interfaces. Technicians shall retrieve, log, and analyze active and historical fault codes, electrical telemetry, system alarms, and CAN bus communication link statistics to isolate hardware or software anomalies prior to and during servicing.

3.2 Corrosion Prevention: Complete replacement of all internal and external sacrificial zinc anodes within the Hamilton Jet pump housing, stator, and nozzle assemblies to ensure complete protection against galvanic corrosion. To include all hardware, O-rings/seals.

3.3 Physical Calibration & Tuning: Rigorous physical verification and fine-tuning of all mechanical adjustments (including steering nozzle alignment, and reversing bucket travel limits) and hydraulic system operational settings (including pressure thresholds, valve response times, and solenoid activation parameters) to ensure complete alignment with OEM factory standards.

3.4 Hydraulic Filtration & Fluid Servicing: Servicing of the Jet Hydraulic Power Unit (JHPU) and integrated control hydraulics. This includes draining and flushing old hydraulic fluid, cleaning internal reservoirs and magnetic strainers to remove any metallic wear debris, replacing all high-pressure and return hydraulic oil filters with new OEM-specified elements, refilling systems with fresh authorized hydraulic fluid, and conducting a complete system bleed to remove air pockets.

3.5 The contractor shall furnish their own laptop loaded with the licensed Blue Arrow Support Tool, USB interface connectors, and OEM replacement parts to complete the work items described in Section 3.0.

3.6 The contractor shall provide a report on the Initial Diagnostic & Pre-Service Scan within 48 hours of the initial inspection onsite to include an electronic fault download (alarms/CANbus drops), initial hydraulic system pressure check, physical inspection log of active seal leaks, and troubleshooting of active faults with recommended repairs (A001).

3.7 The contractor shall provide a Pre-Service Tear-down & Tolerance Report Record of "As-Found" measurements of steering nozzle centerlines, reversing bucket clearances prior to servicing prior to commencing physical replacement/flushing (A001).

3.8 The contractor shall provide a Mechanical & Hydraulic Calibration Checklist of Visual and electronic confirmation detailing final physical adjustments and calibrated hydraulic values prior to launching the vessel (A001).

3.9 The contractor shall provide a Post-Service Sea Trial & Autotune Report Performance log validating Dynamic "Autotune" calibration using Blue Arrow Support Tools, Steady-state and transient hydraulic pressure stability under high-speed loading, Visual verification of seal integrity (zero leakage) under load, Maximum RPM and maneuvering control validation within 48 hours of sea trial completion (A001).

3.10 The contractor shall provide a report to include the physical confirmation of the complete replacement of all internal/external sacrificial zinc anodes, full replacement of mechanical water seals and hydraulic O-rings (with part numbers), disposal of old hydraulic fluid (*Ships force to assist with disposal*) and replacement of high-pressure/return filters, and verification of system bleed. Report to be submitted upon completion of reassembly, prior to sea trial (A002).

4.0 SPECIAL QUALIFICATIONS: Due to the digital complexity of the Blue Arrow network, the Contractor shall deploy technicians meeting these stringent requirements:

4.1 OEM Blue Arrow Certification: Technicians shall hold active, factory-issued certifications specifically in Hamilton Jet Blue Arrow Controls & Diagnostics.

4.2 OEM HJ292 Mechanical Certification: Technician performing physical pump overhauls, shaft seal rebuilds, or bearing adjustments shall hold active, factory-certified Hamilton Jet HJ292 Mechanical Maintenance & Repair qualifications.

4.3 Software Calibration Capability: Technicians shall demonstrate proficiency using the proprietary Blue Arrow Support Tool software for module programming.

4.4 Experience Profile: A minimum of three (3) years of direct experience calibrating digital marine control networks (CAN bus/NMEA2000) and hydraulic interfaces.

5.0 GOVERNMENT FURNISHED EQUIPMENT/PROPERTY/INFORMATION: The government will provide limited access and baseline information to support the contractor's execution of the work to include:

5.1 Unimpeded, escorted physical access to the two (2) 11-meter craft at the designated repair dock or maintenance slip.

5.2 Access to vessel-specific Blue Arrow configuration files, historic alarm logs, and vessel system schematics.

6.0 DELIVERABLES: The Contractor shall compile, manage, and submit the following deliverables to the Technical Point of Contact (TPOC) in accordance with the updated technical objectives:

6.1 Initial Diagnostic & Pre-Service Scan DI-MISC-80508B (A001)

6.2 Pre-Service Tear-down & Tolerance Report DI-MISC-80508B (A001)

6.3 Mechanical & Hydraulic Calibration Checklist DI-MISC-80508B (A001)

6.4 Post-Service Sea Trial & Autotune Report DI-MISC-80508B (A001)

6.5 Certificate of Parts Replacement & Service Log DI-SESS- 81359B (A002)

7.0 SECURITY REQUIREMENTS:

7.1 Base Access & DBIDS: All Contractor technicians shall pass background checks to obtain Defense Biometric Identification System (DBIDS) credentials for military installations.

7.2 Information Security (OPSEC): Proprietary Blue Arrow system configurations, vessel identification numbers, and naval operational logs are classified as OPSEC-sensitive. No photography or offsite transmission of configuration parameters is permitted.

7.3 Government TPOC: Alternate TPOC:

Thomas C. Daubert Gina M. Baker

301.538.7749 757.613.6972 thomas.c.daubert.civ@us.navy.mil gina.m.baker11.civ@us.navy.mil

8.0 PERIOD/PLACE OF PERFORMANCE:

8.1 All work to take place at Naval Base Guam, Santa Rita, Guam 96915

8.2 Period of performance: All work to be completed within 65 days of contract award.

8.3 Water Jet Repair Kit Items

Part Number Item Name Quantity Unit of Issue

206264 SAGINAW PUMP PAINTED ASSY 2 EA

63699 OIL FILTER ELEMENT 10 MICRON 4 EA

206347 O-RING 66.27x3.53 N70 -231 4 EA

203882 OIL LEVEL/TEMPERATURE SENSOR 1 EA

203729 VALVE WANDFLUH PROPORTIONAL 2 EA

203725 COMPENSATOR BYPASS 1 EA

203724 VALVE NEEDLE MV*SUN 2 EA

65024 CYLINDER STEERING HC5303 1 EA

61353 SEAL SCRAPER WYCLIP 4 EA

61362 ROTARY SEAL 25X42X7MM NITRILE 4 EA

112516 KIT SEAL REV CYL MK2 HJ292&322 4 EA

GREASE-NZ CASTROL SPHEEROL 2 EA

203130 ANODE ALUMINIUM 4 EA

203133 ANODE ALUMINIUM 32 EA

201330 NUT NYLOC M8 SS316 56 EA

201394 WASHER SPRING M8 SS316 56 EA

104916 O-RING 304x1.78 N70 CUT 961 4 EA

204177 JET INTERFACE MODULE 1 EA

204382 CABLE 8 T/PAIR SCP-JIMs 12M 1 EA

204376 CABLE 8 T/PAIR SCP-JIMp 12M 1 EA

343483 LOOM 292 BA SCHEMA D 1 EA

Requirements NSWCCD has a requirement for the diagnostics and repair of two (2) Hamilton Jet waterjet propulsion units (specifically HJ322/HJ292).

Continuation of Packaging and Marking

Continuation of Inspection and Acceptance

Overall Contract Inspection/Acceptance Locations

Inspection and Acceptance Location

Both Destination Instructions: See Performance Work Statement (PWS) for Acceptance/inspection criteria.

DoDAAC: N00167 CountryCode: USA

NSWC CARDEROCK

CARDEROCK DIVISION BLDG 143, 9500 MACARTHUR BOULEVARD

BETHESDA, MD 20817-5700

UNITED STATES

TBD, TBD

Email: TBD Telephone: TBD

Inspection and Acceptance Location

Both Destination Instructions: See Performance Work Statement (PWS) for Acceptance/inspection criteria.

DoDAAC: N00167 CountryCode: USA

NSWC CARDEROCK

CARDEROCK DIVISION BLDG 143, 9500 MACARTHUR BOULEVARD

BETHESDA, MD 20817-5700

UNITED STATES

TBD, TBD

Email: TBD Telephone: TBD

Continuation of Deliveries or Performance

Overall Contract Delivery Period

Contractor Destination

Line Item Delivery Schedule Quantity Address and POC Special Handling/Notes

Delivery On Or Before Delivery Date 30 Sep

1 Lot Ship To DoDAAC: N00167 CountryCode: USA

NSWC CARDEROCK

CARDEROCK DIVISION BLDG 143, 9500

MACARTHUR BOULEVARD

BETHESDA, MD 20817-5700

UNITED STATES

TBD, TBD

Email: TBD Telephone: TBD

Delivery Period From 30 Jul 2026 to 30 Sep 2026

1 Each Ship To DoDAAC: N00167 CountryCode: USA

NSWC CARDEROCK

CARDEROCK DIVISION BLDG 143, 9500

MACARTHUR BOULEVARD

BETHESDA, MD 20817-5700

UNITED STATES

TBD, TBD

Email: TBD Telephone: TBD

FoB Details Contractor Destination

Continuation of Accounting and Appropriation Data

Contract Clauses

FAR Clauses Incorporated by Reference

Number Title Effective Date

Alternate/ Deviation

Variation Effective Date

52.204-13 System for Award Management-Maintenance. (Deviation 2026-O0038) Feb 2026 52.226-8 Encouraging Contractor Policies to Ban Text Messaging While Driving. May 2024 52.232-33 Payment by Electronic Funds Transfer-System for Award Management. Oct 2018 52.233-3 Protest after Award. (Deviation 2026-O0038) Feb 2026 52.233-4 Applicable Law for Breach of Contract Claim. (Deviation 2026-O0038) Feb 2026

52.212-4 Terms and Conditions-Commercial Products and Commercial Services. (Deviation 2026- O0038)

Feb 2026

DFARS Clauses Incorporated by Reference

Number Title Effective Date

Alternate/ Deviation

Variation Effective Date

252.203-7000 Requirements Relating to Compensation of Former DoD Officials. Sep 2011 252.203-7002 Requirement to Inform Employees of Whistleblower Rights. Dec 2022

252.204-7018 Prohibition on the Acquisition of Covered Defense Telecommunications Equipment or Services.

Jan 2023

252.232-7003 Electronic Submission of Payment Requests and Receiving Reports. Dec 2018 252.232-7010 Levies on Contract Payments. Dec 2006 252.247-7023 Transportation of Supplies by Sea. Oct 2024 252.204-7004 Antiterrorism Awareness Training for Contractors. Jan 2023 252.204-7015 Notice of Authorized Disclosure of Information for Litigation Support. Jan 2023 252.223-7008 Prohibition of Hexavalent Chromium. Jan 2023 252.243-7002 Requests for Equitable Adjustment. Dec 2022 252.244-7000 Subcontracts for Commercial Products or Commercial Services. Nov 2023 252.246-7008 Sources of Electronic Parts. Jan 2023

DFARS Clauses Incorporated by Full Text

252.232-7006 Wide Area WorkFlow Payment Instructions. (Jan 2023)

WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023)

(a) As used in this clause- Definitions.

"Department of Defense Activity Address Code (DoDAAC)" is a six position code that uniquely identifies a unit, activity, or organization.

"Document type" means the type of payment request or receiving report available for creation in Wide Area WorkFlow (WAWF).

"Local processing office (LPO)" is the office responsible for payment certification when payment certification is done external to the entitlement system.

"Payment request" and "receiving report" are defined in the clause at 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports.

(b) The WAWF system provides the method to electronically process vendor payment requests and receiving reports, as Electronic invoicing.

authorized by Defense Federal Acquisition Regulation Supplement (DFARS) 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports.

(c) To access WAWF, the Contractor shall- WAWF access.

(1) Have a designated electronic business point of contact in the System for Award Management at https://www.sam.gov; and

(2) Be registered to use WAWF at https://wawf.eb.mil/ following the step-by-step procedures for self-registration available at this web site.

(d) The Contractor should follow the training instructions of the WAWF Web-Based Training Course and use the Practice WAWF training.

Training Site before submitting payment requests through WAWF. Both can be accessed by selecting the "Web Based Training" link on the WAWF home page at https://wawf.eb.mil/

(e) Document submissions may be via web entry, Electronic Data Interchange, or File Transfer WAWF methods of document submission.

Protocol.

(f) The Contractor shall use the following information when submitting payment requests and receiving reports in WAWF payment instructions.

WAWF for this contract or task or delivery order:

(1) The Contractor shall submit payment requests using the following document type(s): Document type.

(i) For cost-type line items, including labor-hour or time-and-materials, submit a cost voucher.

(ii) For fixed price line items-

(A) That require shipment of a deliverable, submit the invoice and receiving report specified by the Contracting Officer.

Invoice and Receiving Report (COMBO)

(B) For services that do not require shipment of a deliverable, submit either the Invoice 2in1, which meets the requirements for the invoice and receiving report, or the applicable invoice and receiving report, as specified by the Contracting Officer.

N/A

(iii) For customary progress payments based on costs incurred, submit a progress payment request.

(iv) For performance based payments, submit a performance based payment request.

(v) For commercial financing, submit a commercial financing request.

(2) ) Fast Pay requests are only permitted when Federal Acquisition Regulation (FAR) 52.213-1 is included in the contract.

[Note: The Contractor may use a WAWF "combo" document type to create some combinations of invoice and receiving report in one step.]

(3) The Contractor shall use the information in the Routing Data Table below only to fill in applicable fields in WAWF Document routing.

when creating payment requests and receiving reports in the system.

Routing Data Table*

Field Name in WAWF Data to be entered in WAWF

Pay Official DoDAAC N62825

Issue By DoDAAC N00167

Admin DoDAAC N00167

Inspect By DoDAAC N00167

Ship To Code N00167

Ship From Code ____

Mark For Code ____

Service Approver (DoDAAC) ____

Service Acceptor (DoDAAC) ____

Accept at Other DoDAAC ____

LPO DoDAAC ____

DCAA Auditor DoDAAC ____

Other DoDAAC(s) ____

(*Contracting Officer: Insert applicable DoDAAC information. If multiple ship to/acceptance locations apply, insert "See Schedule" or "Not applicable.")

(**Contracting Officer: If the contract provides for progress payments or performance-based payments, insert the DoDAAC for the contract administration office assigned the functions under FAR 42.302(a)(13).)

(4) The Contractor shall ensure a payment request includes documentation appropriate to the type of payment request in Payment request.

accordance with the payment clause, contract financing clause, or Federal Acquisition Regulation 52.216-7, Allowable Cost and Payment, as applicable.

(5) The Contractor shall ensure a receiving report meets the requirements of DFARS Appendix F. Receiving report.

(g) WAWF point of contact.

(1) The Contractor may obtain clarification regarding invoicing in WAWF from the following contracting activity's WAWF point of contact.

Ademola Oriowo at 301-503-0809 or by email ademola.m.oriowo.civ@us.navy.mil NAVSEA Helpdesk at WAWFHQ@navy.mil

CONUS ONLY: 866-618-5988, COMMERCIAL: 801-605-7095

You can also contact the SAP Coordinator: Tricia Middleton at or (757)478-5625patricia.l.middleton.civ@us.navy.mil

(2) Contact the WAWF helpdesk at 866-618-5988, if assistance is needed.

(End of clause)

252.204-7021 Contractor Compliance with the Cybersecurity Maturity Model Certification Level Requirements.

(Nov 2025)

CONTRACTOR COMPLIANCE WITH THE CYBERSECURITY MATURITY MODEL CERTIFICATION LEVEL REQUIREMENTS (NOV 2025)

(a) . As used in this clause- Definitions

"Controlled unclassified information" means information the Government creates or possesses, or information an entity creates or possesses for or on behalf of the Government, that a law, regulation, or Governmentwide policy requires or permits an agency to handle using safeguarding or dissemination controls (32 CFR 2002.4(h)).

N0016726Q1131 mailto:patricia.l.middleton.civ@us.navy.mil

"Current" means-

(1) With regard to Conditional Cybersecurity Maturity Model Certification (CMMC) Status-

(i) Not older than 180 days for Conditional Level 2 (Self) assessments and Conditional Level 2 (certified third-party assessment organization (C3PAO)) assessments, with-

(A) No changes in compliance with the requirements at 32 CFR part 170 since the Conditional CMMC Status date (see 32 CFR

170.16 and 170.17); and

(B) A corresponding affirmation of continuous compliance by an affirming official (see 32 CFR 170.4); and

(ii) Not older than 180 days for Conditional Level 3 (Defense Industrial Base Cybersecurity Assessment Center (DIBCAC)) assessments, with-

(A) No changes in compliance with the requirements at 32 CFR part 170 since the Conditional CMMC Status date (see 32 CFR 170.18); and

(B) A corresponding affirmation of continuous compliance by an affirming official;

(2) With regard to Final CMMC Status-

(i) Not older than 1 year for Final Level 1 (Self), with-

(A) No changes in compliance with the requirements at 32 CFR part 170 since the Final CMMC Status date (see 32 CFR 170.15); and

(B) A corresponding affirmation of continuous compliance, not older than 1 year, by an affirming official;

(ii) Not older than 3 years for Final Level 2 (Self) assessments and Final Level 2 (C3PAO) assessments, with-

(A) No changes in compliance with the requirements at 32 CFR part 170 since the Final CMMC Status date (see 32 CFR 170.16 and 170.17); and

(B) A corresponding affirmation of continuous compliance, not older than 1 year, by an affirming official; and

(iii) Not older than 3 years for Final Level 3 (DIBCAC) assessments, with-

(A) No changes in compliance with the requirements at 32 CFR part 170 since the Final CMMC Status date (see 32 CFR 170.18); and

(B) A corresponding affirmation of continuous compliance, not older than 1 year, by an affirming official; and

(3) With regard to affirmation of continuous compliance (32 CFR 170.22), not older than 1 year with no changes in compliance with the requirements at 32 CFR part 170.

"Cybersecurity Maturity Model Certification (CMMC) status" means the result of meeting or exceeding the minimum required score for the corresponding assessment. The potential statuses are as follows:

(1) Final Level 1 (Self).

(2) Conditional Level 2 (Self).

(3) Final Level 2 (Self).

(4) Conditional Level 2 (C3PAO).

(5) Final Level 2 (C3PAO).

(6) Conditional Level 3 (DIBCAC).

(7) Final Level 3 (DIBCAC).

"Cybersecurity Maturity Model Certification unique identifier (CMMC UID)" means 10 alpha-numeric characters assigned to each CMMC assessment and reflected in the Supplier Performance Risk System (SPRS) for each contractor information system.

"Federal contract information (FCI)" means information, not intended for public release, that is provided by or generated for the Government under a contract to develop or deliver a product or service to the Government. It does not include information provided by the Government to the public, such as on public websites, or simple transactional information, such as information necessary to process payments.

"Plan of action and milestones" means a document that identifies tasks to be accomplished. It details resources required to accomplish the elements of the plan, any milestones in meeting the tasks, and scheduled completion dates for the milestones, as defined in National Institute of Standards and Technology Special Publication 800-115 (32 CFR 170.21).

(b) . The Cybersecurity Maturity Model Certification (CMMC) is a framework for assessing a contractor's compliance with Framework applicable information security protections (see 32 CFR part 170).

(c) . The CMMC assessments will not duplicate efforts from any other comparable DoD assessment, except for rare circumstances Duplication when a reassessment may be necessary, for example, when there are indications of issues with cybersecurity and/or compliance with CMMC requirements.

(d) . The Contractor shall- Requirements

(1)(i) Have and maintain for the duration of the contract a current CMMC status at the following CMMC level, or higher: ____ for all information Contracting Officer insert: CMMC Level 1 (Self); CMMC Level 2 (Self); CMMC Level 2 (C3PAO); or CMMC Level 3 (DIBCAC) systems used in performance of the contract, task order, or delivery order that process, store, or transmit FCI or CUI; and

(ii) Consult 32 CFR 170.23 related to the flowdown of the CMMC requirements, and flow down the correct CMMC level to subcontracts and other contractual instruments;

(2) Only process, store, or transmit FCI or CUI on contractor information systems that have a CMMC status at the CMMC level required in paragraph (d)(1) of this clause, or higher;

(3) Complete on an annual basis, and maintain as current, an affirmation, by the affirming official (see 32 CFR 170.4), of continuous compliance with the requirements associated with the CMMC level required in paragraph (d)(1) of this clause in the Supplier Performance Risk System (SPRS) ( ) for each CMMC UID applicable to each of the contractor information systems that process, store, or transmit FCI https://piee.eb.mil or CUI and that are used in performance of the contract;

(4) Ensure all subcontractors and suppliers complete prior to subcontract award, and maintain on an annual basis, an affirmation, by the affirming official (see 32 CFR 170.4), of continuous compliance with the requirements associated with the CMMC level required for the subcontract or other contractual instrument for each of the subcontractor information systems that process, store, or transmit FCI or CUI and that are used in performance of the subcontract; and

(5) If the Contractor has a CMMC Status of Conditional, successfully close out a valid plan of action and milestones (32 CFR 170.21) to achieve a CMMC Status of Final.

(e) . The Contractor shall- Reporting

(1) Submit to the Contracting Officer-

(i) The CMMC UID(s) issued by SPRS for contractor information systems that will process, store, or transmit FCI or CUI during performance of the contract; and

(ii) Any changes in the CMMC UIDs generated in SPRS throughout the life of the contract, task order, or delivery order, if applicable;

(2) Enter into SPRS the results of a current self-assessment for each CMMC UID, not covered by a C3PAO assessment or DIBCAC assessment, applicable to each of the contractor information systems that process, store, or transmit FCI or CUI and that are used in performance of the contract; and

(3) Complete in SPRS on an annual basis and maintain as current an affirmation of continuous compliance by the affirming official (see 32 CFR 170.4) for each self-assessment, C3PAO assessment, or DIBCAC assessment required under the contract in SPRS.

(f) . The Contractor shall- Subcontracts

(1) Insert the substance of this clause, including this paragraph (f) and excluding paragraph (e)(1), in subcontracts and other contractual instruments, including those for the acquisition of commercial products or commercial services, excluding commercially available off-the-shelf items, if the subcontract or other contractual instrument will contain a requirement to process, store, or transmit FCI or CUI; and

(2) Prior to awarding a subcontract or other contractual instrument, ensure that the subcontractor has a current CMMC certificate or current CMMC status at the CMMC level that is appropriate for the information that is being flowed down to the subcontractor based on the requirements at 32 CFR 170.23.

(End of clause)

252.211-7003 Item Unique Identification and Valuation. (Jan 2023)

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)

(a) . As used in this clause- Definitions

"Automatic identification device" means a device, such as a reader or interrogator, used to retrieve data encoded on machine-readable media.

"Concatenated unique item identifier" means-

(1) For items that are serialized within the enterprise identifier, the linking together of the unique identifier data elements in order of the issuing agency code, enterprise identifier, and unique serial number within the enterprise identifier; or

(2) For items that are serialized within the original part, lot, or batch number, the linking together of the unique identifier data elements in order of the issuing agency code; enterprise identifier; original part, lot, or batch number; and serial number within the original part, lot, or batch number.

"Data matrix" means a two-dimensional matrix symbology, which is made up of square or, in some cases, round modules arranged within a perimeter finder pattern and uses the Error Checking and Correction 200 (ECC200) specification found within International Standards Organization (ISO)/International Electrotechnical Commission (IEC) 16022.

"Data qualifier" means a specified character (or string of characters) that immediately precedes a data field that defines the general category or intended use of the data that follows.

"DoD recognized unique identification equivalent" means a unique identification method that is in commercial use and has been recognized by DoD. All DoD recognized unique identification equivalents are listed at . https://www.acq.osd.mil/asda/dpc/ce/ds/unique-id.html

"DoD item unique identification" means a system of marking items delivered to DoD with unique item identifiers that have machine-readable data elements to distinguish an item from all other like and unlike items. For items that are serialized within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier and a unique serial number. For items that are serialized within the part, lot, or batch number within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier; the original part, lot, or batch number; and the serial number.

" Enterprise " means the entity (e.g., a manufacturer or vendor) responsible for assigning unique item identifiers to items.

" Enterprise identifier" means a code that is uniquely assigned to an enterprise by an issuing agency.

"Government's unit acquisition cost" means-

(1) For fixed-price type line, subline, or exhibit line items, the unit price identified in the contract at the time of delivery;

(2) For cost-type or undefinitized line, subline, or exhibit line items, the Contractor's estimated fully burdened unit cost to the Government at the time of delivery; and

(3) For items produced under a time-and-materials contract, the Contractor's estimated fully burdened unit cost to the Government at the time of delivery.

"Issuing agency" means an organization responsible for assigning a globally unique identifier to an enterprise, as indicated in the Register of Issuing Agency Codes for ISO/IEC 15459, located at http://www.aimglobal.org/?Reg_Authority15459.

"Issuing agency code" means a code that designates the registration (or controlling) authority for the enterprise identifier.

"Item" means a single hardware article or a single unit formed by a grouping of subassemblies, components, or constituent parts.

" Lot or batch number" means an identifying number assigned by the enterprise to a designated group of items, usually referred to as either a lot or a batch, all of which were manufactured under identical conditions.

"Machine-readable" means an automatic identification technology media, such as bar codes, contact memory buttons, radio frequency identification, or optical memory cards.

"Original part number" means a combination of numbers or letters assigned by the enterprise at item creation to a class of items with the same form, fit, function, and interface.

"Parent item" means the item assembly, intermediate component, or subassembly that has an embedded item with a unique item identifier or DoD recognized unique identification equivalent.

"Serial number within the enterprise identifier" means a combination of numbers, letters, or symbols assigned by the enterprise to an item that provides for the differentiation of that item from any other like and unlike item and is never used again within the enterprise.

"Serial number within the part, lot, or batch number" means a combination of numbers or letters assigned by the enterprise to an item that provides for the differentiation of that item from any other like item within a part, lot, or batch number assignment.

"Serialization within the enterprise identifier" means each item produced is assigned a serial number that is unique among all the tangible items produced by the enterprise and is never used again. The enterprise is responsible for ensuring unique serialization within the enterprise identifier.

"Serialization within the part, lot, or batch number" means each item of a particular part, lot, or batch number is assigned a unique serial number within that part, lot, or batch number assignment. The enterprise is responsible for ensuring unique serialization within the part, lot, or batch number within the enterprise identifier.

"Type designation" means a combination of letters and numerals assigned by the Government to a major end item, assembly or subassembly, as appropriate, to provide a convenient means of differentiating between items having the same basic name and to indicate modifications and changes thereto.

"Unique item identifier" means a set of data elements marked on items that is globally unique and unambiguous. The term includes a concatenated unique item identifier or a DoD recognized unique identification equivalent.

"Unique item identifier type" means a designator to indicate which method of uniquely identifying a part has been used. The current list of accepted unique item identifier types is maintained at .https://www.acq.osd.mil/asda/dpc/ce/ds/unique-id.html

(b) The Contractor shall deliver all items under a contract line, subline, or exhibit line item.

(c) Unique item identifier.

(1) The Contractor shall provide a unique item identifier for the following:

(i) Delivered items for which the Government's unit acquisition cost is $5,000 or more, except for the following line items:

Contract Line, Subline, or

Exhibit Line Item Number Item Description

(ii) Items for which the Government's unit acquisition cost is less than $5,000 that are identified in the Schedule or the following table:

Contract Line, Subline, or

Exhibit Line Item Number Item Description

(If items are identified in the Schedule, insert "See Schedule in this table.)

(iii) Subassemblies, components, and parts embedded within delivered items, items with warranty requirements, DoD serially managed reparables and DoD serially managed nonreparables as specified in Attachment Number .____

(iv) Any item of special tooling or special test equipment as defined in FAR 2.101 that have been designated for preservation and storage for a Major Defense Acquisition Program as specified in Attachment Number .____

(v) Any item not included in (i), (ii), (iii), or (iv) for which the contractor creates and marks a unique item identifier for traceability.

(2) The unique item identifier assignment and its component data element combination shall not be duplicated on any other item marked or registered in the DoD Item Unique Identification Registry by the contractor.

(3) The unique item identifier component data elements shall be marked on an item using two dimensional data matrix symbology that complies with ISO/IEC International Standard 16022, Information technology - International symbology specification - Data matrix; ECC200 data matrix specification.

(4) The Contractor shall ensure that- Data syntax and semantics of unique item identifiers.

(i) The data elements (except issuing agency code) of the unique item identifier are encoded within the data matrix symbol that is marked on the item using one of the following three types of data qualifiers, as determined by the Contractor:

(A) Application Identifiers (AIs) (Format Indicator 05 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology - EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI MH

10.8.2 Data Identifier and Application Identifier Standard.

(B) Data Identifiers (DIs) (Format Indicator 06 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology - EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI MH

10.8.2 Data Identifier and Application Identifier Standard.

(C) Text Element Identifiers (TEIs) (Format Indicator 12 of ISO/IEC International Standard 15434), in accordance with the Air Transport Association Common Support Data Dictionary; and

(ii) The encoded data elements of the unique item identifier conform to the transfer structure, syntax, and coding of messages and data formats specified for Format Indicators 05, 06, and 12 in ISO/IEC International Standard 15434, Information Technology - Transfer Syntax for High Capacity Automatic Data Capture Media.

(5) . Unique item identifier

(i) The Contractor shall-

(A) Determine whether to-

Serialize within the enterprise identifier; (1)

Serialize within the part, lot, or batch number; or (2)

Use a DoD recognized unique identification equivalent (e.g. Vehicle Identification Number); and (3)

(B) Place the data elements of the unique item identifier (enterprise identifier; serial number; DoD recognized unique identification equivalent; and for serialization within the part, lot, or batch number only: original part, lot, or batch number) on items requiring marking by paragraph (c)(1) of this clause, based on the criteria provided in MIL-STD-130, Identification Marking of U.S. Military Property, latest version;

(C) Label shipments, storage containers and packages that contain uniquely identified items in accordance with the requirements of MIL-STD-129, Military Marking for Shipment and Storage, latest version; and

(D) Verify that the marks on items and labels on shipments, storage containers, and packages are machine readable and conform to the applicable standards. The contractor shall use an automatic identification technology device for this verification that has been programmed to the requirements of Appendix A, MIL-STD-130, latest version.

(ii) The issuing agency code-

(A) Shall not be placed on the item; and

(B) Shall be derived from the data qualifier for the enterprise identifier.

(d) For each item that requires item unique identification under paragraph (c)(1)(i), (ii), or (iv) of this clause or when item unique identification is provided under paragraph (c)(1)(v), in addition to the information provided as part of the Material Inspection and Receiving Report specified elsewhere in this contract, the Contractor shall report at the time of delivery, as part of the Material Inspection and Receiving Report, the following information:

(1) Unique item identifier.

(2) Unique item identifier type.

(3) Issuing agency code (if concatenated unique item identifier is used).

(4) Enterprise identifier (if concatenated unique item identifier is used).

(5) Original part number (if there is serialization within the original part number).

(6) Lot or batch number (if there is serialization within the lot or batch number).

(7) Current part number (optional and only if not the same as the original part number).

(8) Current part number effective date (optional and only if current part number is used).

(9) Serial number (if concatenated unique item identifier is used).

(10) Government's unit acquisition cost.

(11) Unit of measure.

(12) Type designation of the item as specified in the contract schedule, if any.

(13) Whether the item is an item of Special Tooling or Special Test Equipment.

(14) Whether the item is covered by a warranty.

(e) For embedded subassemblies, components, and parts that require DoD item unique identification under paragraph (c)(1)(iii) of this clause or when item unique identification is provided under paragraph (c)(1)(v), the Contractor shall report as part of the Material Inspection and Receiving Report specified elsewhere in this contract, the following information:

(1) Unique item identifier of the parent item under paragraph (c)(1) of this clause that contains the embedded subassembly, component, or part.

(2) Unique item identifier of the embedded subassembly, component, or part.

(3) Unique item identifier type.**

(4) Issuing agency code (if concatenated unique item identifier is used).**

(5) Enterprise identifier (if concatenated unique item identifier is used).**

(6) Original part number (if there is serialization within the original part number).**

(7) Lot or batch number (if there is serialization within the lot or batch number).**

(8) Current part number (optional and only if not the same as the original part number).**

(9) Current part number effective date (optional and only if current part number is used).**

(10) Serial number (if concatenated unique item identifier is used).**

(11) Description.

** Once per item.

(f) The Contractor shall submit the information required by paragraphs (d) and (e) of this clause as follows:

(1) End items shall be reported using the receiving report capability in Wide Area WorkFlow (WAWF) in accordance with the clause at 252.232-7003. If WAWF is not required by this contract, and the contractor is not using WAWF, follow the procedures at http://dodprocurementtoolbox.com/site/uidregistry/.

(2) Embedded items shall be reported by one of the following methods-

(i) Use of the embedded items capability in WAWF;

(ii) Direct data submission to the IUID Registry following the procedures and formats at http://dodprocurementtoolbox.com/site /uidregistry/; or

(iii) Via WAWF as a deliverable attachment for exhibit line item number (fill in) , Unique Item Identifier Report for Embedded ____ Items, Contract Data Requirements List, DD Form 1423.

(g) . If the Contractor acquires by subcontract, any item(s) for which item unique identification is required in accordance with Subcontracts paragraph (c)(1) of this clause, the Contractor shall include this clause, including this paragraph (g), in the applicable subcontract(s), including subcontracts for commercial products or commercial services.

(End of clause)

Addendum to 52.212-4, Contract Terms and Conditions - Commercial Products and Commercial Services

Contract Terms and Conditions Required To Implement Statutes or Executive Orders — Commercial Products and Commercial Services

Addendum to Contract Clauses

Contract Clauses

FAR Clauses Incorporated by Reference

Number Title Effective Date

Alternate/ Deviation

Variation Effective Date

52.240-91 Security Prohibitions and Exclusions. (Deviation 2026-O0038) Feb 2026

52.244-6 Subcontracts for Commercial Products and Commercial Services. (Deviation 2026- O0038)

Apr 2026

52.222-90 Addressing DEI Discrimination by Federal Contractors. (Deviation 2026-O0038) Apr 2026 52.232-39 Unenforceability of Unauthorized Obligations. Jun 2013

DFARS Clauses Incorporated by Reference

Number Title Effective Date

Alternate/ Deviation

Variation Effective Date

252.211-7008 Use of Government-Assigned Serial Numbers. Sep 2010 252.225-7013 Duty-Free Entry. Aug 2025 252.225-7048 Export-Controlled Items. Jun 2013 252.237-7010 Prohibition on Interrogation of Detainees by Contractor Personnel. Jan 2023 252.239-7010 Cloud Computing Services. Jan 2023

252.204-7012 Safeguarding Covered Defense Information and Cyber Incident Reporting.

(DEVIATION 2024-O0013 REVISION 1)

May 2024 Deviation 2024-O0013 May 2024

252.225-7972 Prohibition on the Procurement of Foreign-Made Unmanned Aircraft Systems. (DEVIATION 2024-O0014)

Aug 2024 Deviation 2024-O0014 Aug 2024

FAR Clauses Incorporated by Full Text

52.252-2 Clauses Incorporated by Reference. (Feb 1998)

Clauses Incorporated By Reference (Feb 1998)

This contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at this/these address(es):

www.acquisition.gov

(End of clause)

52.252-6 Authorized Deviations in Clauses. (Nov 2020)

Authorized Deviations in Clauses (Nov 2020)

(a) The use in this solicitation or contract of any Federal Acquisition Regulation (48 CFR Chapter 1) clause with an authorized deviation is indicated by the addition of "(DEVIATION)" after the date of the clause.

(b) The use in this solicitation or contract of any Defense Federal Acquisition Regulation (48 CFR Chapter 2) clause with an authorized deviation is indicated by the addition of "(DEVIATION)" after the name of the regulation.

(End of clause)

Additional Regulation or Supplemental Clauses Incorporated by Full Text

G-242-H001 GOVERNMENT CONTRACTADMINISTRATION POINTS-OF-CONTACT AND

RESPONSIBILITIES (NAVSEA) (OCT 2023)

(Oct 2023)

(a) The Government reserves the right to administratively substitute any of the points of contact listed below at any time.

(b) The contracting officer is the only person authorized to change this contract or orders issued thereunder. The Contractor shall not comply with any order, direction or request of Government personnel - that would constitute a change - unless it is issued in writing and signed by the Contracting Officer or is pursuant to specific authority otherwise included as part of this contract. If, in the opinion of the contractor, an effort outside the existing scope of this contract is requested, the contractor shall promptly comply with the Notification of Changes clause of this contract.

(c) The points of contact are as follows:

(i) The Procuring Contracting Officer (PCO) is:

Name: Sydney Mcdonald-Johnson Address:

904 Corporate Lane Chesapeake, VA 23320 Phone: (757) 773-0329 E-mail: sydney.m.mcdonald-johnson.civ@us.navy.mil

(ii) The Contract Specialist is:

Name: Chris Rolince Address:

904 Corporate Lane Chesapeake, VA 23320 Phone: (757) 513-7247 E-mail: Christopher.c.rolince.civ@us.navy.mil

(f) The Technical Point of Contact (TPOC) is the contracting officer's representative for technical matters when a COR is not appointed. The TPOC is responsible for technical issues of contract administration, such as providing all items of Government Furnished Information (GFI), Government Furnished Material (GFM) and Government Furnished Equipment (GFE) if specified in the contract as well as the inspection and acceptance of all contract deliverables.

The Technical Point of Contact (TPOC) is:

Name: [ * ] Address: [ *Street ] [ *City, State, Zip ] Phone: (Area Code) xxx- [xxxx] E-mail: [ * ]

[ * ] To be completed at contract award

(End of Text)

G-242-H002 HOURS OF OPERATION AND HOLIDAY SCHEDULE (NAVSEA) (JUL 2021) (Jul 2021)

(a) The policy of this activity is to schedule periods of reduced operations or shutdown during holiday periods. Deliveries will not be accepted on Saturdays, Sundays or Holidays except as specifically requested by the [insert activity name]. All goods or services attempted to be delivered on a Saturday, Sunday or Holiday without specific instructions from the Contracting Officer or his duly appointed representative will be returned to the contractor at the contractor's expense with no cost or liability to the U.

S. Government.

(b) The federal Government observes public Holidays that have been established under 5 U.S.C. 6103. The actual date of observance for each of the holidays, for a specific calendar year, may be obtained from the OPM website at OPM.GOV or by using the following direct link: https://www.opm.gov/policy-data-oversight/pay-leave/federal-holidays/.

(c) Delayed Opening, Early Dismissal and Closure of Government Facilities. When a Government facility has a delayed opening, is closed or Federal employees are dismissed early (due to severe weather, security threat, security exercise, or a facility related problem) that prevents personnel from working, onsite contractor personnel regularly assigned to work at that

N0016726Q1131 https://www.opm.gov/policy-data-oversight/pay-leave/federal-holidays/ https://www.opm.gov/policy-data-oversight/pay-leave/federal-holidays facility shall follow the same reporting and/or departure directions given to Government personnel. The contractor shall not direct charge to the contract for such time off, but shall follow parent company policies regarding taking leave (administrative or other). Non-essential contractor personnel, who are not required to remain at or report to the facility, shall follow their parent company policy regarding whether they should go/stay home or report to another company facility. Subsequent to an early dismissal, delayed opening, or during periods of inclement weather, onsite contractors should monitor the OPM website as well as radio and television announcements before departing for work to determine if the facility is closed or operating on a delayed arrival basis.

(d) When Federal employees are excused from work due to a holiday or a special event (that is unrelated to severe weather, a security threat, or a facility related problem), on site contractors shall continue working established work hours or take leave in accordance with parent company policy. Those contractor employees who take leave shall not direct charge the non-working hours to the contract. Contractors are responsible for predetermining and disclosing their charging practices for early dismissal, delayed openings, or closings in accordance with the FAR, applicable cost accounting standards, and the company's established policy and procedures.