MIL-STD-361-6(TM)_MANUALS.pdf

I N~ MEASUREMENT

SENSITIVE I

MILsTD-Ml~ Is NLY 1992

SUPERSEDING

(see 65.)

MILITARY ST~AR.D

IVIANUALS, TECHNICAL

INTROIXJCI’ORY INFORMATION WITH

THEORY OF OPERATIONS REQUIREW~

Source: https://assist.dla.mil -- Downloaded: 2021-06-24T16:17Z Check the source to verify that this is the current version before use.

MIL-STD-361-6

1.

the the

2.

and

FOREWORD

This military standard is approved for use by the Department of Army and is available for use by all Departments and Agencies of Department of Defense (DOD).

Beneficial comments (recommendations, additions, and deletions) any pertinent data which may be of use in improving this document should-be addressed to: Commander, USANC Materiel Readiness Support Activity, ATl?N: AHX?ID-EP, ~xington, Kentucky 40511-5101, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of the document or by letter.

3. This document is one part of an n-part bookform standard to be used in the preparation and acquisition of technical manuals that are essential to support (operate and maintain) the variou= types of equipment and weapon systems within the Department of the ArRy.

4. This document covers the introductory information with theory of operations requirements for the preparation of technical manuals.

5. Other parts of this multipart standard are:

MIL-STD-361-1

MIL-STD-361-2

MIL-STD-361-3

MIL-STD-361-4

MIL-STD-361-5

MIL-STD-361-7

141L-STD-361-8

MIL-STD-361-9

HIL-STD-361-1O

MIL-STD-361-11

Writing Style and Format Requirements.

Comprehensibility Requirements.

Requirements for Graphics.

Quality Assurance Requirements.

Requirements for Packaging.

Operator and Preventive Maintenance Instmctions.

Maintenance Instructions.

Troubleshooting Procedures.

Lubrication Instructions.

Repair Parts and Special Tools List (RiWTL).

6. By incorporating standardized and service-unique technical manual requirements; this document and its dash-numbered companion parts, along with the general acquisition specification MIL-M-63008, Acquisition/Preparation Requirements, support the acquisition of technical manuals.

ii

XIL-STD-361-6

CONTENTS

1. SCOPE . . . . . . . . . .. o - ==-=**-=” “==

1.1 scope . . . . . . . . . . ● -*”””””*”

1.2 Purpose . . . . . . . . . -...==””=”

1.3 Applicability. . . . . . - - ● o - ● - - ● -

1.4 Selective application and tailoring

2. APPLICABLE DOCmmrrs . . * ● . ● . * - ● - “ “ “ “ “ “

2.1 Government documamts . . ● - ● = o c ● = ● ●

2.1.1 Specifications, ●tandar*, and ha~~ . D

2.1.2 other Gwa rnment documents and publicatmns .

2.2 Order of precedence . . . . . . . ● ● ● ● ● ●

3. DEFINITIONS. . . . . . . . . . ● ● * ● =* ● = = ● - ●

3.2 Acronyms used in this standafi

3.2 Caution. . . . ..= . . . ● o ● ● -“= = ●

3.3 Chapter. . . . . . . . . . ● ● ● ● * o== =

3.4 Component. . . . . . . . . . . . M ● “ ● ● “

3.!5 Contracting activity . . . . . . . . . ● ● ●

3.6 Equipment. . . . . . . . . . . . ● ● - = ● ●

3.7 Multi-SySt_ e~ipIDSnt - . . . - - - - . ● -

3.8 Note . . . . . . . . .-.= = ● ● ● ““ ● -

3.9 Section. . . . . . . . . . . .= = “ G ● = s

3.10 Systen . . . . ● ● * ● *=- ● =” “ ““ “ “

3.11 Technical manuals (TMs) . . . . . . ● . ● ● ●

3.12 Unit . . . . . . . . . . . ● s - ● ● DO” ●

3.13 Warning. . . . . . . . . . . . - = = o 0 “ ●

4. GENERAL

4.1 4.1.1 4.1.2 4.1.3 4.2 4.2.1 4.2.2 4.3 4.4 4.4.1 4.4.2 4.4.3 4.5

5. DETAILED

5.1 5.3.1 5.1.2

5.1.3 5.1.4 5.2 5.2.1 5.2.2

REQUIREMENTS . . . . . . . . 0 . . ● ● DO* ●

Generals tyle. . . . . . . . . . ● ● ● ● ● ●

Conformance to standard Technical content preparation Security classification markings General information and warning summary . . .

General information . . . . . . . . ● ● ● ● ●

Warning summary. . . . . . . . . ● ● ● -O “ Use of warnings, cautions, and notes Equipment and weapon systems configuration .

Configuration. . . . . . . . . . ● . 0 Q ● ● system equipment . . . . . . . . ● . ● ● ● ●

Associated-system equipment . . . . . . - . .

System environment requirements . . . . . . -

REQUHKEKENTS. . . . . . . . . . . . . .. ● .

Frontmatter . . . . . . . . . . . . ~. ● ●

Front cover. . . . . . 0 . . a- - ● O= ● ●

Title bloclq/reportixagerrors and recommending improvements . . . . . . . . . . .. OO== Tableofcontents. . . . . ..00 *=*=o Howtouse this manual . . . . . ..=ooo Chapter 1 - introduction . . . . . . . . . ●

User orientation . . . ..== om=~=== Section I - general information iiiSource: https://assist.dla.mil -- Downloaded: 2021-06-24T16:17Z i

5.2.2.1 5.2.2.2 5.2.2.3

5.2.2.4 5.2.2.5

5.2.2.6 5.2.2.7 5.2.2.8 5.2.2.9 5.2.2.10 5.2.2.11 5.2.2.12 5.2.2.13 5.2.2.14 5.2.3 5.2.3.1

5.2.3.2 5.2.3.3 5.2.3.4 5.2.3.5 5.2.4 5.3 5.4

6. NOTES . .

6.1 6.2 6.3 6.4 6.5 6.6

FIGQB&S

1.

2.

3.

4.

5.

6.

7.

8.

?#IL-STD-361-6

CONTENTS -

Scope.. . . . . . . . . . . . .- . . . . ● 8 Maintenance forms, records, and reports . . . 9 Reporting equipment improvement recommendations (EAR) . . . . . . . . . . . . . ..o .=0* Corrosion prevention and control (CPC) . . .

Destruction of Army materiel to prevent enemy use. . . . . . . . . . . . . . . . ● . ● ● ●

Preparation for storage or shipment Warranty information . . . . . . . . . ● ● c Nomenclature cross-reference list List of abbreviations . . . . . . . . . . ● o Quality assurance (QA) . . . . . . . . . . ●

Safety, caret and handling . . . . . . . . ●

Nuclear hardness.. . . . . . . ...00 w

Security measures for electronic data Calibration. . . . . . . . . . . . . . - - .

Section II - equipment description and data .

Eguipment characteristics, capabilities, and features . . . . . . . . . . . . . . . . ● ●

Location and description of major components Differences between models Equipment data . . . . . . . . . - . . - ● .

Equipment configuration Section III - theory of operation Quality assurance requirements Packaging and preparation for delivery . . .

Intended use . . . . . . . . . . ● . . 0 ● .

IssueofDODISS. . . . . . . . ● . ● ● ● ● ●

Tailoring guidance . . . . . . ● . . ● ● Q “ Acquisition requirements . . . . . - Supersession data . . . . . . . . . . . - ● .

Subject term (key word) listing . . . . . . ●

Example of compartment area illustration (reference 4.4.i) . . . . . . . ● . . ● **C** ● “ “ “ “ ““ “ Example of full view illustration (reference 5.2.2) . .

Example of reference information (nomenclature cross-reference and abbreviations) (reference 5.2.2.8, 5.2.2.9) . . . . . . . . . . . ● ● . o * ● ● ●

Example of a characteristics paragraph (reference 5.2.3.1) . . . . . . . . . . . . . .* ● ● ● ● ● -* ●

Example of location and description of major components illustration (reference 5.2. 3.2) .0000 ● ** Example of a table showing differe;c&s*between models (reference 5.2.3.3) . . . . . . . . . . . . . . . ● ● ●

Example of equipment data table (reference 5.2.3.4) . .

Example of theory of operation presentation for mechanical equipment (reference 5.2.4)

23 — iv

I MIL+YI’D-361-6

CmTEms

FIG-

9* Example of theory of operation presentation for electrical equipment (reference 5.2.4)

10. Example of theory of operation presentation for multisystem eguipment (referenoe 5.2.4)

XM.MX **.**.*=**-* ● ***- C*”” ”--””27

v

1. SCOPE

1.1 -. This document establishes the content and procedural requirements for preparation of introductory information and theory of operations requirements for &echnical -uals (!F’Ha), revisions, supplements, and ohangom.

~=z x!ums2m* This document supplements the various cmntent requirements in the other parts to this n-part standard for specific types of technical manuals and related publications and doss not alone deliver any technical data. (NOTE: The figures used in this document are examples only. The text of this document takms premsdwce over the figures.)

1*3 ~. The applicability of the requirements contained in this document is governed by the equipment, systems, or weapon systems for which the technical manuals are being developed. This document is applicable for use by the Department of the Army.

1.4 Ctive lication and +a~. . This document contains

some requirements that may not be applicable to the preparation of all technical manuals. Selective application and tailoring of requirements contained in this document are the responsibility of the contracting activity and shall be accomplished through the use of MXIJ-M-63008. The applicability of some requirements is also designated by one of the following statements:

unless requirement is specifically excluded by the contracting activity; or as/when specified by the contracting activity.

2. APPIJCABIZ ~s

2.1 ~*

2.1.1 The following

specifications, standards, and handbooks form a“part of this documant to the extant 8p8ciri8d herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS ) and supplement thereto, cited in the solicitation. (See 6.2. )

SPECIFICATIONS

MILITARY

MIL-M-63008

STANDARDS

MILITARY

MIL-STD”12

XIL-STD-361-1

141L-STD-361-4

141L-STD-361-5

MIL-STD-1388-2

DOD-STD-1686

HAWDBOOKS

MILITARY

Hanuals, Technical: Acquisition/ Preparation Requirements.

Abbreviations for Use on Drawings, and in Specifications, Standards and Technical Documents.

Manuals, Technical: Writing Style - Format Requirements.

Manuals, Technical: Quality Asammme Requirements.

Manuals, Technical: Requirements for Packaging.

DOD Requirements for a Logistic Support Analysis Record.

Electrostatic Discharge Control Program for Protection of Electrical and Electronic Parts, Assemblies and Equipment, Excluding Electrically Initiated Explosive Device8 (Metric).

MIL-HDBK-263 - Electrostatic Discharge Control Handbook for Protection of Electrical and Electronic Parts, Assemblies and Equipment, Excluding Electrically -- Initiated Explosive Devices (Metric).

2Source: https://assist.dla.mil -- Downloaded: 2021-06-24T16:17Z

HIL-STD-361-6

(Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from Standardization Documents Order Desk, Bldg 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5904.

2.1.2 nt doc~ . The following other Government documents and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation.

AR 310-50

AR 380-5

AR 380-380

AR 385-11

AR 385-62

TB 750-93-1

TM 9-1300-206

(copies of other Government documants required by the contractor in connection with specific acquisition functions should be obtained from the contracting activity.)

2*2 ~. In the event of a conflict between the text of this document (WThis document- includes all volumes of MIL-STD-361 series.) and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.

Catalog of Abbreviations and Brevity Codes.

Depa-ent of the Army Information Security Program.

Automation Security.

Ionizing Radiation Protection (Licensing, Control, Transportation, Disposal, and Radiation Safety).

Regulations for Firing Guided Missiles and Heavy Rockets for Training, Target Practice, and Combat.

Functional Grouping Codes: Combat, Tactical, and Support Vehicles and Special Purpose Equipment.

Ammunition and Explosives Standards.

NIL-STD-361-6

3. DEFINITIONS

3 ● 1 ~* ~“ ““””~” “8* ‘n ‘is standard are defined as follows:

a.

b.

c.

d.

e.

f.

9.

h.

i.

j-k.

1.

m.

n.

0.

P“

CPC

DOD

DODXSS

EIR

ESD

LSA

LSAR

MAc

PCB

PMcs

QA

RPSTL

TAME

TM

WTB

3.2 Gautloa

Corrosion Prevention Control.

Department of Defense.

Department of Defense Index of Specifications and Standards.

Equipaent Improvement Recommendation.

Electrostatic Discharge.

Logistic Support Analysis.

Logistic Support Analysis Record.

Maintenance Allocation Chart.

Next Higher Assembly.

Printed Circuit Board.

Preventive Maintenance Checks and Services.

Quality Assurance.

Repair Parts and Special Tools List.

The Army Maintenance Management System.

Technical Manual.

Warranty Technical Bulletin.

A statement or some other notification about an operating or maintenance procedure, practice? or cotiition tiatt if not strictly observed, could result in damage to, or destruction of, equipment or loss of mission effectiveness.

3=3 ~. The major, first-level functional division of a technioal manual (TM).

3=4 ~“ A constituent part not normally considered to be capable of independent operation; a piece part.

3*5 ~. The Department of Defense (DOD) component, activity, or organization of a using military servicer or that organization delegated by a using senice, that is responsible for the selection and determination of requirements _ for THs.

3=6 ~- One or more units capable of performing specified functions.

3.7 . Equipment with numerous sophisticated systems installed, including integrated systems and built-in test capability. Equipment falling into this category requires a high volume of technical information to adequately support operation and maintenance of the equipment. such equipment includes, but is not limited to, installed systems, subsystems and aeronautical equipment, support equipment, and spare parts. The data shall be divided and arranged in TM that contain comprehensive, usable information.

3.8 ~. A stat-nt or some other notification that adds, emphasizes, or clarifies essential information of special importance or interest.

3.9 ~. The second-level functional subdivision of a TM and major division of a chapter.

3.10 ~. A regularly interacting or interdependent group of items forming a unified whole to perform a specific operational function.

3=11 ~- Manuals that contain instructions for the installation, operation, maintenance, and support of weapon systems, weapon system components, and support equipment.

TM information may be presented, according to prior agreement between the contractor and the Government, in any form or characteristic, including hard printed copy, audio and visual displays, electronic imbadded media, disks, other electronic devices, or other media. They normally include operational and maintenance instructions, parts lists, and related technical information or procedures exclusive of administrative procedures.

3.12 ~. An assembly or any combination of spare and repair parts mounted together, normally capable of independent operation in a variety of situations.

3*13 ~. A statement or some other notification about an operating or maintenance procedure, practice, or condition that, if not strictly observed, could result in long term health hazard, injury to, or death of personnel performing the task prescribed in the TM.

5Source: https://assist.dla.mil -- Downloaded: 2021-06-24T16:17Z

4. GENERAL REQUIREMENTS

4*1 ~. This document sate forth introductory information and theory of operations requirements that shall be followed in the preparation and acquisition of TMs, revisions, supplements, and changes.

4.1.1 ~. U~~S r~i~~t i= specifically excluded by the contracting activity, the introduction chapter developed for a T!4shall conform to this document and HIL-STD-361-1.

4.1.2 ~- ~Q fOl~~n9 ~s=lime requirements shall be used, as specified by the contracting activity:

a. tic is reqprd (m . The technical data and instructions developed by the requirements of MIL-STD-1388-2 , DOD Requirements for a Legistic Support Analysis Record (LSAR), shall be used as the baseline to prepare TMs.

b. . The MAC shall be used as the baseline to prepare TMs. The MAC shall be prepared from the equipment top-down breakdown and be in functional group code sequence to consolidate and identify those groups on the list which involve identified maintenance functions. Lbgistic support Analysis (ISA) Output Report 04, Maintenance Allocation Sumaary will be used when available as source data for the final approved MAC.

When specified by the contracting activity and if a waiver of standard requirements is granted, TB 750-93-1 may be used as the baseline for preparing TMs.

4.1.3 $ecuritv clas ific tion s a m~ . All classified IT@ and material shall be safeguarded and identified in accordance with 141L-STD-361-l.

4.2 a s~ ●

4.2.1 ~. General information shall include a brief description of the equipment and reflect the following:

type, series, purpose, limitations, and how, in general, the equipment accomplishes its mission. Appropriate illustrations and exploded views shall be included. If the !llNdescribes more than one model, significant differences shall be explained.

4.2.2 ~ . Refer to ?UL-STD-361-1.

4.3 Dse of waxn.b

.~ . Refer to MIL-STD-361-

1.

I .. 4.4 mment and we~on sv~ .

4.4-1 ~. System areas and compartments shall be described, and the system equipment and components contained in the areas shall be listed. The configuration description shall be supported by separate illustrations of each compartment and area, identifying the listed system equipment. (See figure 1.)

4=4=2 ~- The subsystems/equipment comprising the system shall be identified and described. Other equipment which is installed in the subject system compartments and areas need not be listed in the text or called out in the illustrations if they do not directly affect the operation or maintenance of the subject system. Descriptions of operator-attended ●quipment shall include general statements about the nature and purpose of the controls and indicators. The text shall be suppotied by illustrations. All equipment shall be shown, whenever possible, in relative-scale proportion. If necessary for proper support of the text, equipment shall be illustrated individually with significant features called out.

4.4.3 As applicable, description=

and illustrations of associated-sy;tem equipment shall be limited to the major units of that equipment. The descriptions shall be more condensed than those of subject system ewipment; otie~i~e, the same requirements shall be applicable. In the descriptions, emphasis shall be placed on associated systems equipment that constitutes operational or functional interfaces with the subject system . Such units shall be included in the syetem illustrations.

4=5 ~“ - ap~lic*le8 ‘e following information shall be provided:

a. A list of the environmental control requirements, such as limited temperature, humidity, or other limited conditions. Damage to be expected from exceeding these limits and procedures for minimizing the damage shall be given. These procedures shall give due consideration to the fact that the tactical situation may dictate system operation under conditions exceeding the design limits of the system.

b. A tabular summary of the effects of weather conditions on equipment that will affect system capability or cause equipment damage. This summary shall provide references to any special servicing procedures that must be accomplished because of climatic changes, such as adding antifreeze to coolants.

7Source: https://assist.dla.mil -- Downloaded: 2021-06-24T16:17Z

I

I

MXL-STD-361-6

5. DETAIMD REQUIREMENTS

5*1 ~. The following subparagraphs contain necessary content informat ion for frent matter. Refer to KIL-ST&361-l for front matter format requirements.

~*1*1 ~- The front cover of a standard TM shall be formatted and contain the information as outlined in MIL-STD-361- 1.

5.1.2 Title blockz~rtinu e~

. Refer to MIL-STD-361-1.

5-1-4 ~. This section shall be written to provide information and guidance to familiarize the user with any special or unusual features of the TM. Coverage shall lead the user through the TM and explain important features of the organization and content. For example, the fomnat is explained:

operating, troubleshooting, preventive maintenance checks and services (PMCS) are explained; and repair, maintenance instructions, and other pertinent information are explained. Any peculiarities in the basic arrangement of the TM shall be described. How-to-use information shall not repeat the instructions given within the chapters. If applicable, information shall include reference to and how to use the associated repair patis and special tools list (RPSTL) in conjunction with the TM.

5.2 er 1 introduction . This chapter shall provide the user with information for completing forms and records and familiarize the user with the equipment. Functional and physical descriptions of the major equipment, components, and applicable interface equipment shall be provided.

5.2.1 . At a minimum, Chapter 1 shall consist of the following sections:

Section I. General Information Section II. Equipment Description and Data Section III. Theory of Operation

5.2.2 Se- I - U~

This section shall begin with a full-view illustration of the e&ipment showing features pertinent to the equipment user. A typical full-view illustration is shown in figure 2. This section shall include the following paragraphs, as applicable.

5.2.2.1 SCOD~. The scope paragraph shall contain a brief

statement to tell what is covered in the TM. As applicable, the following information shall be included:

a. Type of manual (to be provided by the contracting activity) .

MIL-STD-3 61-6

I.. b. Model number (s) and equipment name (s) (to be provided by the contracting activity).

I c. Purpose of equipment(s).

I

d. Special inclusions in the ~ual, such as drill procedures or on-vehicle loading plans.

5.2.2.2 e fom . re~~a . ~is paragraph shall contain the following statement:

I “Depa-ent of the Army forms and procedures used for equipment maintenance will be thoee prescribed by (as applicable) DA PAM 738-750, The Army Maintenance Management System (TAMMS); DA PAN 738-751, Functional Users -nual for the my !4aintenance Management Systm - Aviation (T--A):

or AR 700-138, Army Legistics Reediness and Sustainability.w

In addition, for conventional and chemical ammunition TMs, add the following statement:

‘Accidents involving injury to personnel or damage to materiel will be reported on DA Form 285 (Accident Report) in accordance with AR 385-40. Explosives and ammunition malfunctions will be reported in accordance with AR 75-1.”

5.2.2.3 a reoo~ This paragraph shall contain the following statement:

“Xf your (insert equipment short item name) needs ~rov-nt~ let us bow. Send us an EIR. You, the user, are the only one who can tell us what you don’t like about your equipment. Let us know why you donct like the design or performance. Put it on an H’ 368 (Product Quality Deficiency Report). Mail it to the address specified in DA PAM 738-750. We will send you a reply.”

5.2.2.4 Sorro sion Drevent~d control (cPC). This paragraph

shall contain a statement similar to the following:

Corrosion Prevention and Control (CPC) of Army materiel is a continuing concern. It is important that any corrosion problems with this item be reported so that the problem can be corrected and Improvements can be made to prevent the problem in future items.

While corrosion is typically associated with nsting of metals, it can also include deterioration of other materials, such as rubber and plastic. Unusual cracking, softening, swelling, or breaking of these materials may be a corrosion problem.

If a corrosion problem is identified, it can be reported using SF 368, Product Quality Deficiency Report. Use of keywords such as “corrosion,” “rust,” ‘deterioration, w or ‘cracking”

9Source: https://assist.dla.mil -- Downloaded: 2021-06-24T16:17Z

MXL-STD-361-6

I will ensure that the information is identified as a CPC problem.

The form should be submitted to the address specified in DA

PAM 738-750.

For aircraft TMs, this paragraph shall include a reference to TM 55-1500-343-23.

5.2.2.5 strlactj.o~ to nrm~ engmivuse ● This paragraph shall reference the appropriate TH(s) covering the destruction of Army materiel to prevent enemy use. The contracting activity will prmride tha TM number(s) to reference.

5.2.2.6 ~* ~-e requirements, including packaging and administrative storage, shall be part of the maintenance instructions, and reference to those instructions shall appear in this paragraph in Chapter 1.

5.2.2.7 ~atlon . .

When the TM covers equipment that is under warranty and a warra&y technical bulletin (WTB) is published, the ~ shall include only a reference to the applicable WTB. When a WTB is not published, pertinent warranty information shall be provided. An applicable statement such as the following shall be included:

The (insert name of equip~ent) is warranted for (insert miles or other timeframe as appropriate). The warranty starts on the date found in block 23, DA Form 2408-9 in the logbook.

Report all defects to your supervisor, who will take appropriate action.

5.2.2.8 regerqwe lig& . An appropriate cross-reference list shall be included when non-official nomenclature (common name) is approved by the contracting activity (MIL-STD-361-1). See figure 3 for example. Once a common name, abbreviation, or acronym is used, it shall be used consistently throughout the TM.

5.2.2.9 J&?~. A list of abbreviations, consisting of all abbreviations, acronyms, signs, or symbols used in the TM shall be included. For example, see figure 3. For aircraft T14s only, a statement shall be included that abbreviations are in accordance with MIL-STD-12 and AR 310-50, except when the abbreviation stands for a marking actually found in the aircraft.

5.2.2.10 ~- Unless re~ir~ent is specifically excluded by the contracting activity, this paragraph shall be included and shall either reference the pertinent QA TM(s) or shall include the appropriate general QA information.

If QA information is not referenced but is included in the TM, this paragraph shall state that the text of each quality assurance procedure paragraph or step in the TM is preceded (and highlighted) by the addition of w(QA),w and the abbreviation QA ._ shall be explained either in the title of the paragraph or in the text. For aircraft Maintenance THS, refer to FM 1-511.

5.2..2.11 . This paragraph shall cover general precautions and safety regulations.

a. For ammunition T14s,this paragraph shall include information to comply with AR 385-62. References to applicable ARs for range safety and danger zones during training and combat shall be included. Clear explanations and official definitions of such safety-related teram as misfire, hangfire, and cook-off, which describe characteristics associated with the specific items(s) covered by the %’wunder preparation, shall also be included. A reference to TH 9-1300-206 shall be made for general ammunition care, handling, and safety.

b. For TMs covering equipma2t with radioactive partu or components, a l=regraph shall - included to comply with Nuclear Regulatory Commission provisions, and references to applicable ARs and safety documents on radioactive materials shall be included. If additional coverage on radioactive materials is needed, but is not included in applicable documents, such instructions shall be provided here as required. Xn addition, the following information shall be provided throughout the TM:

(1)

(2)

(3)

(4)

(5)

Nuclear warning notices shall be placed at the beginning of any instruction covering procedures that will expose personnel to a nuclear radiation hazard.

Procedures to be followed prior to maintenance actions, or in the event of breakage of radioactive parts or components, including safety, care, and handling instructions, shall also be included.

Radioactive parts or components shall be shown and suitably identified on a parts location diagram or illustration, and suitable warning notices shall be included.

When applicable, equipment data shall include a list of radioactive parts or components and the type and quantity of radioactive material involved.

Instructions for the disposal of radioactive material, such as the refiirement to double bag in plastic all broken tritium sources, shall be provided in accordance with AR 385-11.

c. Electrostatic discharge (ESD) control standards for the protection of electrical and electronic parts, assemblies, and equipment shall be described, when applicable. The ESD classes (see ~D-STD-1686 and MIL-HDBK-263) shall be identified. All ESD sensitive items shall be identified by class and the protective/control measures to be taken

MIL-STD-361- 6

I

I shall be given in instructions provided for such maintenance functions/tasks as removal, disassembly, inspection, repair/replace, assembly, testing, and packaging. Of primary ~rtance in the identification of class 1 items requiring stringent protection are: (1) class I chips on a printed circuit board (~B): (2) pint of reduced or no protection due to absorption by a next higher assembly (NHA); and (3) change in an ESD requirement for a class 1 itea resulting from installation of the item into its NHA.

5.2.2.12 ~. If equipment covered in the TH has nuclear survivability requhemen ts (i.e., overpressure and burst, thermal radiation, electr~gnetic pulse or transient radiation effects on electronics) , (1) this paragraph shall so state; (2) applicable cautions shall be incorporated into the text to ensure that hardness of the equipment is not degraded during operation or maintenance; and (3) all hardness critical processes and steps shall be marked in accordance with MXL-STD-361-1. The following statement shall be included:

‘All hardness critical paragraphs in this manual are marked with the symbol HCP as follows:

a. When an entire paragraph, including all subparagraphs, is considered hardness critical, only the major paragraph will be marked by the symbol HCP, placed between the paragraph number and the title.

b. When only certain processes and steps within a paragraph are hardness critical, only the applicable processes and steps will be marked by placement of the symbol HCP between each applicable step number and the text.”

5.2.2.13 ~ecur~tv m --s for electronic data e . This paragraph shall include instructions for handling, loading, scrubbing, overwriting, or unloading classified electronic data under usual or unusual conditions. Instructions shall meet the requirements of AR 380-5 and AR 380-380 as they pertain to automation security.

5.2.2.14 ~rati~ Equipment requiring calibration shall be indicated and referen~e shall be made to the publication containing the applicable calibration procedure.

5.2.3 section II - ~t ~ . This section shall contain the information in the following paragraphs, as applicable.

5.2.3.1 t act~ c~ This information shall consist of an overall description of the equipment, including general capabilities, special features, and other like information (e.g., applications, liauitations) which will be helpful in the operation and maintenance of the equipment. (See figure 4.)

I_ a.

b.

c.

d.

HIL-STD-361-6

The equipment type, its portability or mobility, operational and special environmental features, and remote conkrol features shall he stated.

Co~nents and their functions shall not be described unless as=e.ntial to continuity. For functional data, reference shall be made to theory of operation, when required.

When equipment covered varies in scope and application @r has several applications within an end item, a brief explanation of the multiple usage shall be made and a simple diagram showing all aspects of a typical application shall be included.

For ammunition TMS, ~ackinq and mckaging shall ~ described, including-numbe~ of r~unds-per pack.

5.2.3.2 . External and internal views of the equipment shall be used to show general features and all major oomponentm. The major components/items in the view shall be explained by the use of keyed text. (See figure 5.) The information contained in this paragraph shall mot duplicate information in the paragraphs covering equipment characteristics, capabilities, and features and equipment data.

a. When the equipment is designed for use with other equipment, one or more diagrams shall be used to illustrate the use of the equipment. Only information pertaining to the user shall be included.

b. Location and contents of end item and major component identification plates shall be illustrated. Modification instruction, and warranty plates, stencils, or location of serial numbers shall be illustrated as necessary to the user.

502 ● 3 ● 3 ~. Siwif icant differenc-between equipment models or units of the same model that affect operator or maintenance actions shall be described, and the extent of interchangeability shall be indicated. These differences shall be related explicitly to equipment model, part number, or serial number ranges in such a manner that the !X34wer can identify the specific equipment configuration involved. When model differences exist but have no effect on operation or maintenance, this fact shall be stated. An example of a typical differences-between-models table is shown in figure 6.

5.2.3.4 ~. perfo~nce data, inc~udin9 n~erical and other standard-related data applying to operational and maintenance functions shall be provided. The equipment data shall summarize the specific capabilities and limitations of the equipment and other critical data needed by the TM user for maintenance of the equipment. Vehicle and cargo space dimensions and metric and other equivalents shall be included where appropriate. See figure 7 for a typical example.

%3Source: https://assist.dla.mil -- Downloaded: 2021-06-24T16:17Z

5.2.3.5 . For equipment which can be cortfiqured several different way-t tifo-tion on tie v~ious possible configurations shall b& provided.

5.2.4 . This section shall contain a simple functional description of how the end item and major components work and interface. The description shall explain what functional affect operation and adjustment of controls, switches, and devices hava on other components of the equipment.

a.

b.

c.

Only absolutely essential information shall be provided which the TH user must know to operate and troubleshoot the equipment. If necessary, functional block diagr-shall be used to illustrate the interface and functional relationships between major components.

Description of components and assemblies which are maintained at higher levels shall be included only where necessary for clarity or continuity.

For multisystam equipment, theory of operation shall be organized ~o the ~ir~t paragraph of the section contains an explanation of the end item as an integrated whole.

Within each end item explanation, there shall be an explanation of the appropriate components; and within each component explanation, there shall be an explanation of the appropriate assemblies. Further breakdowns below the assembly level shall be included as appropriate.

For examples of theory of operation, see figure= 8, 9, and 10-

5-3 ~“ Quality assurance and quality control for TMS, revisions, supplements, and changes shall be in accordance with HIIJ-STD-361-4.

5.4 del iverv. TMs, revisional supplements, and changes shall be packaged in accordance with

141L-STD-361-5.

6. NOTES

(This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.)

6.1 ~. This document prescribes the introductory information with theory of operations requirements applicable to vurious types of technical manuals, revisions~ supplements, and changes prepared by or for the Department of the Army.

~.z ~* When this docuaent is used in acquisition, the applicable issue of the DODISS mist be cited in the solicitation. (See 2.1.1.)

6.3 a anc~ . The contracting activity should tailor any required options offered herein in accordance with MIL-14- 63008.

6.4 Jlcmisition re~em=nts . Acquisition documents should

specify the following:

a. Title, number, and date of this standard.

b. Issue of DODISS to be cited in the solicitation, and, if required, the specific issue of individual documents referenced. (See 2.1.1. )

c. Type of manual (5.2.2.1).

d. Model number(s) and equipment name(s) (5.2.2.1).

e. Destruction of Army materiel to prevent enemy use (5.2.2.5).

6.5 SUD rsee ssion data . This document consolidates, standardizes, and supersedes the introductory information with theory of operation requirements contained in the following documents:

MIL-M-63036D(TM) - Manuals, Technical: Operator’s, Preparation of.

MIIA4-63038C(TH) - Manuals, Technical: Organizational or Aviation Unit, Direct Support or Aviation Intermediate, and General Support Maintenance.

MIL-M-63041E(TM) - Manuals, Technical: Depot Maintenance Work Requirements.

6.6 ~iect term [kev word] . The following terms are to be used to identify this document during retrieval searches:

Accident and safety reports Acronyms used in this document Corrosion prevention and control (CPC) Differences between models Equipment characteristics, capabilities, and features Equipment configuration Equipment data General information Handling and storage Looation and description of najor c~nents Maintenance forms, records, and reports Packaging and pre~ration for delivery Preparation for storage or shipment System environment raquir-ents Technical content requirements Theory of operation user orientation $?arnlngs and cautions Warranty information

MIL-STW36 1-6

I

MM TENSIOMn

I

I t

I L RAM COMP-SSIM

CHOCK

TRANSFER H-

MIOMUNC WNW

coNTRtOL#EL e of com~m nt area l~ustrat~

FIGURE 1.

HIL-STE361-6

MwEn

MOOULE

FIRE

mTTlG&8snlNG

FUEL

MOOUL~

EXMAUST Emta#c

●AUEL

\ I

Ia”cnooru le of fllllVlmw

FIGURE 2.

[r~n? .

I I

MIL-STD-361-6

I I Comlmon Nmw

I FldGage uquidLavdIndbtor

I Iauncbcr(LZL) LaulKkr,Zcm Uagt4 GlirkdM&8ik M740

LoaderTransporter(LT) Lamm4m,OukkdMhdIe, Chrder,Momtuk M752

I JJSTOF ABBREVIATEONS/ACRONYMS.

BDAR BattklieMdurtage ~t8ndre@

I Cl”A Common ableofdiowamxs

HCP Hardnesscriticalpmom

FIGURE 3. e o~ere~4XKS

19Source: https://assist.dla.mil -- Downloaded: 2021-06-24T16:17Z

HIL-STD-361-6

Au~ AND FmT’uREs.

M8ximumspeedwith muimumk3adc#cnly

‘IhikrMatwowhcd$. dktrii

Eachwheelhaaa~ brakeControl H@way SOmph (~ kph) ofeachbrakeisindepemb~oftheother. CroaaauntIY30mph (48kph)

Bodyiscaailyremoved. Cargovolumecapabilityw bC i.MY~ by installingtailgatead rackasacmbiy.

b.Cawbilkksad Features.

CuIvm awa asacmbiyproteascargo6um

MaximumloadlSCXIlb(681kg) weather.

FIGURE 4. e of a (re~ence

20Source: https://assist.dla.mil -- Downloaded: 2021-06-24T16:17Z i

HIL-STD-361-6

nctumlio mAcfmm6mepkcemttyr 8tcd~uite opmtimpforM87Al ~tim gunmoun~ Ml ammmnida -PJ%4a——tlmctmJ mpmwu Raam83wtoeMb& 9Q-mm~7Ahm mdlillcglJn, Baddibcr30~gua 5.

Iodmattarge whmiycthdkm.

1.

z s

4.

Ml COMMANDER%CUPOIA RWMCS adf.cmntaiaut alck=um for~wilhvhiml blockBfcuatcrD81 VbiOrI. C%n18imMlik .S0muhbc gun ad ~ts 6.

Uldawltmbt oopmmcmubbcglm.

COMMUNKXTIOY4COMPONENTS.EmckncS&mlmd- ~~~9mtcmuOk 7.

w rAR’naJLAIE FILm UNIT. ~ a)taul air&oml-fwutbro@lb ufividldbamtohfor

~* pn-r, md *.

M87Al COMBINATION GUN MOUNT. CkimbIS of Rail~mcumq MdDudKd pltshidd. PiwJta inekvauon onllmutnnmiom -~p ad 7.62-mmmuhinc gan.

W-MM WJN. clm9i4&dqUa41MgctUbq =-t@—~&~ “ ~ti MmakEimLIDdD&Stxxc~tar 81uImtmdc bbtdcfkuor. F-~or~.

M737.6Z—MM MACHINE GUN. Mglmei@L air cuJwtccuil opwBtc4maallic link- fedwitb8bml

GUNNERS CONTROLS AND INSTRUMENTS.

~~aQdlr9dr8uuccmQti d rmmpalwata far~galld 7~ machincgtm.

M2 CXIJBER .50 MACHINE GUN, FM, TT.

*tcmmtiq Rutkpm81c4 link-bell f~ air q bcmybmd(l-m>t wm!ttypc(m’). Fim damicattyor

FIGURE 5.

Comm nents illustration (reference 5.2.3

HIL-STD-36 1-6

This paragraph shows major equipment and operational differences bstween models of M44A2 series vehicles. It has been organized in tabular form for easy reference by operators.

Tablo 1-1. Difforeauos Between Medals.

wmIaE n a m m a II a a m m s a -sPTIa OMACIE21ST1CS 3 3 s 6 5 s 1 1 2 s 7 7 - m.)

5 5 6 ● ● ● ● ● 7 4 5 6 A A A A & A 9 s 5 2 6 4 2 2 2 z 2 3 A a A A :

c c 3 3 2 2

Sdy Feotures:

Sdtt-in A-Frae x

* Protector

2.31 x x x 2.30,2.31,2.32

Esrth Boring Machine x 2.32 FLood[i@hts x 2.31

Xonradcible lki~t x x 1.28 ~t siti x x x x x x x x x ..

-r Minch x x 2.3t,2.32 Rtifble Heisht x x x x x x x x x x 1.28 Raw&le Sides x x 2.23,2.31

@eratiuOld Capat+tlittes:

cDr90#elaane 1 x x x x x 2.23,2.30

~ ~rot Ionc x 2.30 Earth DoriW Polaetttm x 2.32

S@mt Repeir x x 2.22 Fifth Wwd Operot ions x 2.29

Fud Servicing x 2.26 Pipeline con8t-tlon x 2.31 wter $emicine x x 2.27

Wm81baos:

142 in. 060.6 m) x -.

1% in. (3W.1 -) x x x x x x x x x x --

190 In. (432.6 @ x -.

FIGURE 6c le of a t*e s~ betw~

Wmlmlu aND DnImmoNs

RA9dyfor’lbwd

E4npkcduithc81moai9ThvdL=k

MIL-STD-361-6

I

=.1 cm (152 in.)

Wdth 370.8m (146 in.)

Hdght 1s2.9m (72 in.)

~) 444.5 m (Y75in.)

Height (Cannon Full

EkMlion) 2921 cm (11S in.)

T-M I@’ Mdnpc

FIIlm$Rmc -sbotlpl!r Mimltc

Hi@ R8tc MmSPm b R8te lpo apl!

BIUU Limb - I-IlghRate On@ Io, mcw,orloord

RADAR RANGE

Miaimtlm 2SOm(’273yd) udmum 5@00 m (5,466yd)

(lqmctcrmrgcq

FIGURE 7. le of e~ t-e (r~ 5.2.3.41 .

23Source: https://assist.dla.mil -- Downloaded: 2021-06-24T16:17Z

NIL-STD-361-6

Iw m. ~ Imlarm FLmcTIm

1 Error l~~cetorLight Wat i 1hdmted, ldicete8 i~r qration of f i h ( control eesdAy.

2 Poei t i w/neg*t ive Switch Set*the~{~t Co_ ●ither peitive or neeetive type ●icrof i lm.

3 Sateittvity Control Proviche djutunt of Hitivity of Cde Semiql cirdts d in qomtic frae retrievai qrotion.

4 Clear Button Ckears ●llk~rd entrioe, extirguishee ●rror light, Uld stope film ~t -~.

5 Reset S@ ton Provides -i lity of eetti~ microf i Lm stortin@ fra tvdaer to -r entered cm keytmerd.

6 Rewind Sutta Provfdee rotor dr{va ,icrof ila rewind qi I ity.

7 Sewch Sutton Initlatee fr~ retrieve( dwm ~eed.

8 +1 Sutton * ●icrofitm - f- fomwrd UhU1.depoud.

9 -1 Suttal Movee ●ieroff1-m fra in rever8e b depre8Ded.

10 0 thru 9 auttom Per9its entering of cheifmd frmt ndmr.

l!=+

FIGUR& 8. Dr8~t ion for e 5.2.4) .

XIL-STD-361-6

u

A. MAR AWTEXM. Par-l ic ref Later With CO1kcts reflected energy froa targets along mtefm boreet*t exis. Olechenfcmlly positioned to eeerch for end treck targets. ~lste8 si~l to develqututh md devetim pinti~-wror sigrmiz for poeitioni~.

B. WVEGUIDECUtPOWEllTS. Pe-it w of ● •l~le antm for both tramaittiw and r’eceivimi. Circd=te mer’w frOXI trmexittl~ fmctim to amrem and frox mtemt to TU tb . Circadcte my mergy refiected f- TK ttbe to resistive load.

FIGURE 9. Qf m.-esentation for. .

elect~cal e~nt (referenae 5.2 . .

HIL-STKP361-6

& J’ork Asumbay. ‘me484ncblongside read AS tbC fork CUT@C mOVG Up, tbC top OfthC forks are axmecld to the fork carriage 7he fork hydraulic piston assemblycomesinoontactwitit Carriagemovesupawldownqmw chains Ube$nnermastIfthebydraulic*n~up driveabyahjdratllic-adpbmm mfock mox%itw*-mt~*ti* fork Carriageisrollormowtim tbeinnermost Carriagt%l%rbmbtim deckleuelto assemblyRoM mountedOninnermastmovein 60inchcaabOvethetibYm*g tiefork channelswhichmakeuptheoutermastassembly. carriage.

I

FIGURE 10. 10 of theom of ~on ‘ox

26Source: https://assist.dla.mil -- Downloaded: 2021-06-24T16:17Z

MIL-STD-361-6

INDEX

I

AC~hit.iOn 5egUh-eXWS Acronyms used in this standard Applicability

APPLICABLE DOCUMENTS

Associated-system equi~ment Calibration Caution Chapter Chapter 1 - introduction C~nent Configuration Conformance to standard Contracting activity Corrosion prevention a;d*c&&;lO(&P&)* : : :

DEFINITIONS

Destruction of Army materiel to prevent enemy use

DETAILED REQUIREMENTS

Differences between models Eguipment Equipment and weapon systems configuration .

Equipment characteristics, capabilities, and features Equipment configuration Equipment data Front cover Front matter General information General information and warning summary . . .

GENERALREQUXREKENTS

General style Government documents Howto use this manual Intended use IssueofDODISS List of abbreviations Location and description of major components Maintenance forms, records, and reports . . .

Multi-system equipment Nomenclature cross-reference list Note

NOTES

Nuclear hardness Orderof precedence . . . . . . - Other Government documents and publications .

Packaging and preparation for delivery . . .

Preparation for storage or shipment Purpose Quality assurance (QA) Quality assurance requirim~nts Reporting equipment improvement recommendation

(EAR)

Is

. 6.4

. 3.1

. 1.3

. . 2.

4.4.3

5.2.2.14 . 3.2 . 3.3 . 5.2 . 3.4

4.4.1 4.1.1

. 3.5 5.2.2.4 . . 3.

5.2.2.5 . . 5.

5.2.3.3 . 3.6 . 4.4

5.2.3.1 5.2.3.5 5.2.3.4

5.1.1 . 5.1

4.2.1 . 4.2 . . 4.

. 4.1 . 2.1

5.1.4 . 6.1 . 6.2 5.2.2.9 5.2.3.2 5.2.2.2 . 3.7 5.2.2.8 . 3.8

6.

;.;.2.12 . 2.2

2.1.2 . 5.4 5.2.2.6

1.2 ;.2.2.10 . 5.3

5.2.2.3

27Source: https://assist.dla.mil -- Downloaded: 2021-06-24T16:17Z

HIL-ST~36 1-6

INDEX

Safety, care, and handling . ● . . . ● ● ● scope.. . ● - . ● - ● .- ● ● -* - “ ““ scope.. .** ● .*** ● - * ● “ “ “ “ “

SCOPE. . . . . . . . . .- ● . -- = ● ● ●

Section. . . . . . . . . ● . ● .-. ● ● ●

Section I - general information Section II - equipment description and data Section III - theory of operation Security classification markings Securitv measures for electronic data . . .

. . 5.2.2.11

.0.= 1.1

● . 5.2.2.1 ..*** 1.

..0. 3.9 .** 5.2.2 ..0 5.2.3 ..* 5.2.4 .** 4.1.3 .0 5.2.2.13

Selecti~e application and tailoring Specifications, standards, and handbooks . .

subject term (key word) listing Super8ession data Systen . . . . . . . . . - . . . - . -w- “ System environment requirements SystemeWiwent Tableofcontents Tailoring guidance Technical content preparation Technical manuals (TMs) Title block/reporting errors and recommending improvements Unit . . . . . . .- . . - . ● ● “. “ W“ ●

Use of warnings, cautions, and notes ● . ● ●

User orientation.. . . .. OOO=O”= ●

Warning. . . . . . . . . . . - .* ● - ● ● ●

Wamingsummary. . . . . . . . . . . - ● ● ●

.0.

1.4 2.1.1

6.6 6.5

3.10 4.5

4.4.2 5.1.3

6.3 4.1.2 3.11

5.1.2 3.12 4.3

5.2.1 3.13

4.2.2 Warranty information . . . . . . . . . . = ● - 5.2.2.7

I

HIL-STD-361-6

CU~DIAM :

Army-m

PXBPARXMG AcTrvrmz

Army-m

(PBOJBCT TMBS 0276-6)

REVIIEUACTIVXTXBS:

Army - AL, AR, AT, AV, CR, CU, EA, ER, Pm, MI, Sc

USBB ACTIVITY:

Army - MD

I i

Commander USMC Materiel Readiness Suppofi Activity

AT1’N: A14XHD-EP

Lexington, KY 40521-5101

I

J Source: https://assist.dla.mil -- Downloaded: 2021-06-24T16:17Z srANDARDSZKI’ION DocuMmT IMPROVEMENTmo~ !

...... ...,....,,,,.................... ............,,:.::,,..-V=ie’;:: ‘[ ~~~,:.{~ z ~ DATE (YYMM?O)

.,,., ,.. .,.,..,,, .,,,:..:, ..’ .,: . . . . MXL-6TD-3C1-6 {TM) 920715...... ,.

3. DOCUMmTTTnX

Xntroduotory Inforutioa with Thumy of Opuatiom R.quira.atm

S.RIM.SON FOR RECOMMENDATION

u PJU3PAUU4G ACI’M7Y

& NAME b. ‘T13WPHONE (~ ~ ~)

USAMC Natoriol Raadiness Support (1)~ (2)AU’KWON

Activity (606) 293-3469 74S-3469

CmDRE=fl&apti) rFYouDOuOT RECJ31VEAJU?J’LY wrrHm45DAYs, CxmTAcl?

mm: Mmm-EP (mss) Ddam? Qdiq’ - ~~~ -

L9xilagton, m 40511-5101 521131m=lUugPik%SutilqF--tiVA 2Z041-M66 TckpbaIc (703) 736-M AUlYWONZlJ9-~

(-uMuthadzal Ckululic Vcmim)