MATERIAL ORDERING DATA.pdf

MATERIAL ORDERING DATA

ION: N4523A 0203-1011

ICN: 38RTC25601 KO: U01

Paragraph 4 Ordering Data

KOi: 001

ASTM-F-1123, STANDARD SPECIFICATION FOR NON-METALLIC EXPANSION JOINTS,

dated 31 DECEMBER 1987

(From ASTM-F-1123) 4.1 Orders for products under this specification shall include the following information:

4.1.1 Inside diameter of connecting pipes Ooint ID): 46 inches

4.1.2 Face-to-face dimension that is the flange-to-flange dimension into which the expansion joint is to be installed: 12 inches

4.1.3 Maximum and minimum operating pressure in pounds-force per square inch gage (pascals): 40 psig max, 21 psig min

4.1.4 Maximum and minimum operating temperature in °F (°C): 105 F max, 60 F min

4.1.5 Flange drilling in accordance with the appendix titled "Common Flange Dimension/Drilling Chart" of the Technical Handbook on Rubber Expansion Joints and Flexible Pipe Connectors (herein referred to as the Technical Handbook) or in accordance with special customer requirements: Drill ONE Flange only for 46" dia. joint - 42 (ea) 1- 5/16" dia holes on a 52" bolt dia circle

4.1.6 Fluid to be handled: Seawater

4.1.7 This ASTM specification designation: ASTM F 1123-87

4.1.8 Movement data requirements (including shock or vibratory excursions if applicable):

Not required

4.1.9 Design certification burst test if required (see 9.1 ): Not required

4.1.10 Hydrostatic or special tests if required (see 9.2): Hydrostatic test

4.1.11 Certification of expansion joint if required (see Section 12): Not required

4.1.12 Certified detailed drawing of the expansion joint if required (see 12.2): Not required

Additional Data requirements: Expansion joint will be hydrostatically tested at 60 psig. Certified test data is required.

Prepared By: Matthew Swanson

Code: 260.7

IDN: N4523A 0203-1013

ICN: 38RTC25602 KO: U01

Paragraph 4 Ordering Data

KOi: 001

ASTM-F-1123, STANDARD SPECIFICATION FOR NON-METALLIC EXPANSION JOINTS,

dated 31 DECEMBER 1987

(From ASTM-F-1123) 4.1 Orders for products under this specification shall include the following information:

4.1.1 Inside diameter of connecting pipes (joint ID): 46 inches

4.1.2 Face-to-face dimension that is the flange-to-flange dimension into which the expansion joint is to be installed: 12 inches

4.1.3 Maximum and minimum operating pressure in pounds-force per square inch gage (pascals): 40 psig max, 21 psig min

4.1.4 Maximum and minimum operating temperature in °F (°C): 105 F max, 60 F min

4.1.5 Flange drilling in accordance with the appendix titled "Common Flange Dimension/Drilling Chart" of the Technical Handbook on Rubber Expansion Joints and Flexible Pipe Connectors (herein referred to as the Technical Handbook) or in accordance with special customer requirements: Drill ONE Flange only for 46" dia. joint- 42 (ea) 1- 5/16" dia holes on a 52" bolt dia circle

4.1.6 Fluid to be handled: Seawater

4.1.7 This ASTM specification designation: ASTM F 1123-87

4.1.8 Movement data requirements (including shock or vibratory excursions if applicable):

Not required

4.1.9 Design certification burst test if required (see 9.1): Not required

4.1.1 O Hydrostatic or special tests if required (see 9.2): Hydrostatic test

4.1 .11 Certification of expansion joint if required (see Section 12): Not required

4.1.12 Certified detailed drawing of the expansion joint if required (see 12.2): Not required

Additional Data requirements: Expansion joint will be hydrostatically tested at 60 psig. Certified test data is required.

ION: N4523A 0203-1014

ICN: 38RTC25603 KO: U01

Paragraph 4 Ordering Data

KOi: 001

ASTM-F-1123, STANDARD SPECIFICATION FOR NON-METALLIC EXPANSION JOINTS,

dated 31 DECEMBER 1987

(From ASTM-F-1123) 4.1 Orders for products under this specification shall include the following information:

4.1.1 Inside diameter of connecting pipes Goint ID): 46 inches

4.1.2 Face-to-face dimension that is the flange-to-flange dimension into which the expansion joint is to be installed: 12 inches

4.1.3 Maximum and minimum operating pressure in pounds-force per square inch gage (pascals): 40 psig max, 21 psig min

4.1.4 Maximum and minimum operating temperature in cF (°C): 105 F max, 60 F min

4.1.5 Flange drilling in accordance with the appendix titled "Common Flange Dimension/Drilling Chart" of the Technical Handbook on Rubber Expansion Joints and Flexible Pipe Connectors (herein referred to as the Technical Handbook) or in accordance with special customer requirements: Drill ONE Flange only for 46" dia. joint - 42 (ea) 1- 5/16" dia holes on a 52" bolt dia circle

4.1.6 Fluid to be handled: Seawater

4.1.7 This ASTM specification designation: ASTM F 1123-87

4.1.8 Movement data requirements (including shock or vibratory excursions if applicable):

Not required

4.1 .9 Design certification burst test if required (see 9.1): Not required

4.1.10 Hydrostatic or special tests if required (see 9.2): Hydrostatic test

4.1.11 Certification of expansion joint if required (see Section 12): Not required

4.1.12 Certified detailed drawing of the expansion joint if required (see 12.2): Not required

Additional Data requirements: Expansion joint will be hydrostatically tested at 60 psig. Certified test data is required.

IDN: N4523A 0203-1015

ICN: 38RTC25604 KO: U01

Paragraph 4 Ordering Data

KOi: 001

ASTM-F-1123, STANDARD SPECIFICATION FOR NON-METALLIC EXPANSION JOINTS,

dated 31 DECEMBER 1987

(From ASTM-F-1123) 4.1 Orders for products under this specification shall include the following information:

4.1.1 Inside diameter of connecting pipes 0oint ID): 46 inches

4.1 .2 Face-to-face dimension that is the flange-to-flange dimension into which the expansion joint is to be installed: 12 inches

4.1.3 Maximum and minimum operating pressure in pounds-force per square inch gage (pascals): 40 psig max, 21 psig min

4.1.4 Maximum and minimum operating temperature in °F (°C): 105 F max, 60 F min

4.1.5 Flange drilling in accordance with the appendix titled "Common Flange Dimension/Drilling Chart" of the Technical Handbook on Rubber Expansion Joints and Flexible Pipe Connectors (herein referred to as the Technical Handbook) or in accordance with special customer requirements: Drill ONE Flange only for 46" dia. joint- 42 (ea) 1- 5/16" dia holes on a 52" bolt dia circle

4.1.6 Fluid to be handled: Seawater

4.1. 7 This ASTM specification designation: ASTM F 1123-87

4.1.8 Movement data requirements (including shock or vibratory excursions if applicable):

Not required

4.1.9 Design certification burst test if required (see 9.1 ): Not required

4.1.10 Hydrostatic or special tests if required (see 9.2): Hydrostatic test

4.1.11 Certification of expansion joint if required (see Section 12): Not required

4.1.12 Certified detailed drawing of the expansion joint if required (see 12.2): Not required

Additional Data requirements: Expansion joint will be hydrostatically tested at 60 psig. Certified test data is required.

ION: N4523A 0203-1016

ICN: 38RTC25601 KO: U02

Paragraph 4 Ordering Data

KOi: 001

ASTM-F-1123, STANDARD SPECIFICATION FOR NON-METALLIC EXPANSION JOINTS,

dated 31 DECEMBER 1987

(From ASTM-F-1123) 4.1 Orders for products under this specification shall include the following information:

4.1.1 Inside diameter of connecting pipes Ooint ID): 42 inches

4.1.2 Face-to-face dimension that is the flange-to-flange dimension into which the expansion joint is to be installed: 12 inches

4.1.3 Maximum and minimum operating pressure in pounds-force per square inch gage (pascals): 40 psig max, 21 psig min

4.1.4 Maximum and minimum operating temperature in °F (°C): 105 F max, 60 F min

4.1.5 Flange drilling in accordance with the appendix titled "Common Flange Dimension/Drilling Chart" of the Technical Handbook on Rubber Expansion Joints and Flexible Pipe Connectors (herein referred to as the Technical Handbook) or in accordance with special customer requirements: Drill ONE Flange only for 42" dia. joint- 38 (ea) 1- 5/1611 dia holes on a 47-3/4" bolt dia circle

4.1.6 Fluid to be handled: Seawater

4.1. 7 This ASTM specification designation: ASTM F 1123-87

4.1.8 Movement data requirements (including shock or vibratory excursions if applicable):

Not required

4.1.9 Design certification burst test if required (see 9.1 ): Not required

4.1.10 Hydrostatic or special tests if required (see 9.2): Hydrostatic test

4.1.11 Certification of expansion joint if required (see Section 12): Not required

4.1.12 Certified detailed drawing of the expansion joint if required (see 12.2): Not required

Additional Data requirements: Expansion joint will be hydrostatically tested at 60 psig. Certified test data is required.

ION: N4523A 0203-1017

ICN: 38RTC25602 KO: U02

Paragraph 4 Ordering Data

KOi: 001

ASTM-F-1123, STANDARD SPECIFICATION FOR NON-METALLIC EXPANSION JOINTS,

dated 31 DECEMBER 1987

(From ASTM-F-1123) 4.1 Orders for products under this specification shall include the following information:

4.1 .1 Inside diameter of connecting pipes 0oint ID): 42 inches

4.1.2 Face-to-face dimension that is the flange-to-flange dimension into which the expansion joint is to be installed: 12 inches

4 .1.3 Maximum and minimum operating pressure in pounds-force per square inch gage (pascals): 40 psig max, 21 psig min

4.1.4 Maximum and minimum operating temperature in °F (°C): 105 F max, 60 F min

4.1 .5 Flange drilling in accordance with the appendix titled "Common Flange Dimension/Drilling Chart" of the Technical Handbook on Rubber Expansion Joints and Flexible Pipe Connectors (herein referred to as the Technical Handbook) or in accordance with special customer requirements: Drill ONE Flange only for 42" dia. joint - 38 (ea) 1- 5/16" dia holes on a 47-3/4" bolt dia circle

4.1 .6 Fluid to be handled: Seawater

4.1. 7 This ASTM specification designation: ASTM F 1123-87

4.1.8 Movement data requirements (including shock or vibratory excursions if applicable):

Not required

4.1.9 Design certification burst test if required (see 9.1 ): Not required

4.1.1 O Hydrostatic or special tests if required (see 9.2): Hydrostatic test

4.1.11 Certification of expansion joint if required (see Section 12): Not required

4.1.12 Certified detailed drawing of the expansion joint if required (see 12.2): Not required

Additional Data requirements: Expansion joint will be hydrostatically tested at 60 psig. Certified test data is required.

ION: N4523A 0203-1018

ICN: 38RTC25603 KO: U02

Paragraph 4 Ordering Data

KOi: 001

ASTM-F-1123, STANDARD SPECIFICATION FOR NON-METALLIC EXPANSION JOINTS,

dated 31 DECEMBER 1987

(From ASTM-F-1123) 4.1 Orders for products under this specification shall include the following information:

4.1.1 Inside diameter of connecting pipes Qoint ID): 42 inches

4.1.2 Face-to-face dimension that is the flange-to-flange dimension into which the expansion joint is to be installed: 12 inches

4.1.3 Maximum and minimum operating pressure in pounds-force per square inch gage (pascals): 40 psig max, 21 psig min

4.1.4 Maximum and minimum operating temperature in °F (°C): 105 F max, 60 F min

4.1.5 Flange drilling in accordance with the appendix titled "Common Flange Dimension/Drilling Chart" of the Technical Handbook on Rubber Expansion Joints and Flexible Pipe Connectors (herein referred to as the Technical Handbook) or in accordance with special customer requirements: Drill ONE Flange only for 42" dia. joint- 38 (ea) 1- 5/16" dia holes on a 47-3/4" bolt dia circle

4.1.6 Fluid to be handled: Seawater

4.1.7 This ASTM specification designation: ASTM F 1123-87

4.1.8 Movement data requirements (including shock or vibratory excursions if applicable):

Not required

4.1.9 Design certification burst test if required (see 9.1 ): Not required

4.1.10 Hydrostatic or special tests if required (see 9.2): Hydrostatic test

4.1.11 Certification of expansion joint if required (see Section 12): Not required

4.1 .12 Certified detailed drawing of the expansion joint if required (see 12.2): Not required

Additional Data requirements: Expansion joint will be hydrostatically tested at 60 psig. Certified test data is required.

ION: N4523A 0203-1019

ICN: 38RTC25604 KO: U02

Paragraph 4 Ordering Data

KOi: 001

ASTM-F-1123, STANDARD SPECIFICATION FOR NON-METALLIC EXPANSION JOINTS,

dated 31 DECEMBER 1987

(From ASTM-F-1123) 4.1 Orders for products under this specification shall include the following information:

4.1.1 Inside diameter of connecting pipes Uoint ID): 42 inches

4.1.2 Face-to-face dimension that is the flange-to-flange dimension into which the expansion joint is to be installed: 12 inches

4.1.3 Maximum and minimum operating pressure in pounds-force per square inch gage (pascals): 40 psig max, 21 psig min

4.1.4 Maximum and minimum operating temperature in °F (°C): 105 F max, 60 F min

4.1.5 Flange drilling in accordance with the appendix titled "Common Flange Dimension/Drilling Chart" of the Technical Handbook on Rubber Expansion Joints and Flexible Pipe Connectors (herein referred to as the Technical Handbook} or in accordance with special customer requirements: Drill ONE Flange only for 42" dia. joint - 38 (ea} 1- 5/16" dia holes on a 47-3/4" bolt dia circle

4.1.6 Fluid to be handled: Seawater

4.1.7 This ASTM specification designation: ASTM F 1123-87

4.1.8 Movement data requirements (including shock or vibratory excursions if applicable):

Not required

4.1.9 Design certification burst test if required (see 9.1 ): Not required

4.1.1 O Hydrostatic or special tests if required (see 9.2): Hydrostatic test

4.1.11 Certification of expansion joint if required (see Section 12): Not required

4.1.12 Certified detailed drawing of the expansion joint if required (see 12.2): Not required

Additional Data requirements: Expansion joint will be hydrostatically tested at 60 psig. Certified test data is required.

IDN: N4523A 0203-1020

ICN: 38RTC25601 KO: U03

Paragraph 4 Ordering Data

KOi: 001

ASTM-F-1123, STANDARD SPECIFICATION FOR NON-METALLIC EXPANSION JOINTS,

dated 31 DECEMBER 1987

(From ASTM-F-1123) 4.1 Orders for products under this specification shall include the following information:

4.1.1 Inside diameter of connecting pipes Uoint ID): 28 inches

4.1.2 Face-to-face dimension that is the flange-to-flange dimension into which the expansion joint is to be installed: 12 inches

4.1.3 Maximum and minimum operating pressure in pounds-force per square inch gage (pascals): 40 psig max, 21 psig min

4.1.4 Maximum and minimum operating temperature in °F (°C): 105 F max, 60 F min

4.1.5 Flange drilling in accordance with the appendix titled "Common Flange Dimension/Drilling Chart" of the Technical Handbook on Rubber Expansion Joints and Flexible Pipe Connectors (herein referred to as the Technical Handbook) or in accordance with special customer requirements: Drill ONE Flange only for 2811 dia. joint - 32 (ea) 1- 3/1611 dia holes on a 32-7 /1611 bolt dia circle

4.1.6 Fluid to be handled: Seawater

4.1. 7 This ASTM specification designation: ASTM F 1123-87

4.1.8 Movement data requirements (including shock or vibratory excursions if applicable):

Not required

4.1.9 Design certification burst test if required (see 9.1 ): Not required

4.1.10 Hydrostatic or special tests if required (see 9.2): Hydrostatic test

4.1 .11 Certification of expansion joint if required (see Section 12): Not required

4.1.12 Certified detailed drawing of the expansion joint if required (see 12.2): Not required

Additional Data requirements: Expansion joint will be hydrostatically tested at 60 psig. Certified test data is required.

IDN: N4523A 0203-1021

ICN: 38RTC25602 KO: U03

Paragraph 4 Ordering Data

KOi: 001

ASTM-F-1123, STANDARD SPECIFICATION FOR NON-METALLIC EXPANSION JOINTS,

dated 31 DECEMBER 1987

(From ASTM-F-1123) 4.1 Orders for products under this specification shall include the following information:

4.1.1 Inside diameter of connecting pipes (joint ID): 28 inches

4.1.2 Face-to-face dimension that is the flange-to-flange dimension into which the expansion joint is to be installed: 12 inches

4.1.3 Maximum and minimum operating pressure in pounds-force per square inch gage (pascals): 40 psig max, 21 psig min

4.1.4 Maximum and minimum operating temperature in °F (°C): 105 F max, 60 F min

4.1.5 Flange drilling in accordance with the appendix titled "Common Flange Dimension/Drilling Chart" of the Technical Handbook on Rubber Expansion Joints and Flexible Pipe Connectors (herein referred to as the Technical Handbook) or in accordance with special customer requirements: Drill ONE Flange only for 28" dia. joint- 32 (ea) 1- 3/16" dia holes on a 32-7 /16" bolt dia circle

4.1 .6 Fluid to be handled: Seawater

4.1.7 This ASTM specification designation: ASTM F 1123-87

4.1.8 Movement data requirements (including shock or vibratory excursions if applicable):

Not required

4.1.9 Design certification burst test if required (see 9.1): Not required

4.1.1 O Hydrostatic or special tests if required (see 9.2): Hydrostatic test

4.1.11 Certification of expansion joint if required (see Section 12): Not required

4.1.12 Certified detailed drawing of the expansion joint if required (see 12.2): Not required

Additional Data requirements: Expansion joint will be hydrostatically tested at 60 psig. Certified test data is required.

ION: N4523A 0203-1022

ICN: 38RTC25603 KO: U03

Paragraph 4 Ordering Data

KOi: 001

ASTM-F-1123, STANDARD SPECIFICATION FOR NON-METALLIC EXPANSION JOINTS,

dated 31 DECEMBER 1987

(From ASTM-F-1123) 4.1 Orders for products under this specification shall include the following information:

4.1.1 Inside diameter of connecting pipes 0oint ID): 28 inches

4.1.2 Face-to-face dimension that is the flange-to-flange dimension into which the expansion joint is to be installed: 12 inches

4.1.3 Maximum and minimum operating pressure in pounds-force per square inch gage (pascals): 40 psig max, 21 psig min

4.1.4 Maximum and minimum operating temperature in °F (°C): 105 F max, 60 F min

4.1.5 Flange drilling in accordance with the appendix titled "Common Flange Dimension/Drilling Chart" of the Technical Handbook on Rubber Expansion Joints and Flexible Pipe Connectors (herein referred to as the Technical Handbook) or in accordance with special customer requirements: Drill ONE Flange only for 28" dia. joint- 32 (ea) 1- 3/16" dia holes on a 32-7/16" bolt dia circle

4.1.6 Fluid to be handled: Seawater

4.1.7 This ASTM specification designation: ASTM F 1123-87

4.1.8 Movement data requirements (including shock or vibratory excursions if applicable):

Not required

4.1.9 Design certification burst test if required (see 9.1 ): Not required

4.1.1 O Hydrostatic or special tests if required (see 9.2): Hydrostatic test

4.1.11 Certification of expansion joint if required (see Section 12): Not required

4.1.12 Certified detailed drawing of the expansion joint if required (see 12.2): Not required

Additional Data requirements: Expansion joint will be hydrostatically tested at 60 psig. Certified test data is required.

ION: N4523A 0203-1023

ICN: 38RTC25604 KO: U03

Paragraph 4 Ordering Data

KOi: 001

ASTM-F-1123, STANDARD SPECIFICATION FOR NON-METALLIC EXPANSION JOINTS,

dated 31 DECEMBER 1987

(From ASTM-F-1123) 4.1 Orders for products under this specification shall include the following information:

4.1.1 Inside diameter of connecting pipes (joint ID): 28 inches

4.1.2 Face-to-face dimension that is the flange-to-flange dimension into which the expansion joint is to be installed: 12 inches

4.1.3 Maximum and minimum operating pressure in pounds-force per square inch gage (pascals): 40 psig max, 21 psig min

4.1.4 Maximum and minimum operating temperature in °F (°C): 105 F max, 60 F min

4.1.5 Flange drilling in accordance with the appendix titled "Common Flange Dimension/Drilling Chart" of the Technical Handbook on Rubber Expansion Joints and Flexible Pipe Connectors (herein referred to as the Technical Handbook) or in accordance with special customer requirements: Drill ONE Flange only for 28" dia. joint- 32 (ea) 1- 3/1611 dia holes on a 32-7/16" bolt dia circle

4.1.6 Fluid to be handled: Seawater

4.1 .7 This ASTM specification designation: ASTM F 1123-87

4.1.8 Movement data requirements (including shock or vibratory excursions if applicable):

Not required

4.1.9 Design certification burst test if required (see 9.1 ): Not required

4.1.10 Hydrostatic or special tests if required (see 9.2): Hydrostatic test

4.1.11 Certification of expansion joint if required (see Section 12): Not required

4.1.12 Certified detailed drawing of the expansion joint if required (see 12.2): Not required

Additional Data requirements: Expansion joint will be hydrostatically tested at 60 psig. Certified test data is required.