MarineLS Tech Data.pdf

SHIRT, MAN'S, LONG SLEEVE, KHAKI SHADE M-1, SHALL BE MADE IN ACCORDANCE

WITH CLASS 1 OF MIL-S-3649G DATED 12 OCTOBER 1989 AND ATTACHMENT 1A DATED 12 APRIL 2010 (NOTE: ATTACHMENT 1A IS SUPPLIED BY DSCP ONLY - AND THE CHANGES ARE FOR THE NEW

SHIRT DESIGN).

PATTERN DATE: 26 April 2006

NOTE: THIS SHIRT IS NOW PROCURED WITH MIL-S-3649G

AND ATTACHMENT 1A. ATTACHMENT 1A IS SUPPLIED WITH THIS

SOLICITATION UNDER SEPERATE COVER. THERE ARE ALSO

ADDITIONAL CHANGES TO ATTACHMENT 1A THAT ARE NEAR THE

END OF THIS TECH DATA.

ADDITIONAL INFORMATION FOR MIL-S-3649G:

PATTERN DATE: 26 APRIL 2006

STANDARD SAMPLE OF CLOTH, TROPICAL: POLYESTER

AND WOOL, MIL-C-29404, MARINE CORPS KHAKI SHADE

M-1, IS APPLICABLE FOR SHADE, FINISH, HAND,

FILLING AND COLORFASTNESS - ROLL NO. 3875

APPLIES.

INTERIM SPECIFICATION CHANGES TO MIL-S-3649G:

PAGE 1,PARA. 1.2, UNDER "NECK SIZE" ADD "18-1/2"

AND UNDER "SLEEVE LENGTH" ADD "33, 34, 35, 36,

37".

PAGE 2, PARA. 2.1.1, UNDER "SPECIFICATIONS",

"MILITARY", DELETE "MIL-T-43548-THREAD,

POLYESTER, COTTON COVERED AND RAYON COVERED" AND

ADD UNDER "SPECIFICATIONS", "FEDERAL",

"A-A-50199-THREAD, POLYESTER CORE, COTTON- OR

POLYESTER-COVERED".

PAGE 2, PARA. 2.1.1, UNDER "SPECIFICATIONS",

"MILITARY", DELETE "MIL-C-43594- CLOTH,

INTERLINING, POLYESTER" AND ADD UNDER

"SPECIFICATIONS", "FEDERAL", "A-A-50135-CLOTH,

INTERLINING, POLYESTER".

PAGE 2, PARA.2.1.1, UNDER "SPECIFICATIONS",

"MILITARY", DELETE "MIL-P-55010 - PLASTIC SHEET,

POLYETHYLENE TEREPHTHALATE" IN ITS ENTIRETY.

PAGE 2, PARA. 2.1.1, UNDER "SPECIFICATIONS",

"MILITARY", ADD "MIL-C-44296 - CLOTH, FUSIBLES".

PAGE 4, PARA.3.3.3.1, LINE 3, DELETE

"MIL-C-43594" AND SUBSTITUTE "A-A-50135".

PAGE 4, PARA. 3.3.3.1, AT THE END OF THE LAST

SENTENCE ADD "AS AN ALTERNATE, A NONWOVEN

FUSIBLE CONFORMING TO TYPE V, CLASS 2 OR 3,

STYLE B OF MIL-C-44296 MAY BE USED."

PAGE 4, PARA. 3.3.4, LINE 2, DELETE

"MIL-T-43548" AND SUBSTITUE "A-A-50199 TYPE I"

PAGE 4, PARA. 3.3.4, LINE 3, DELETE "TICKET NO."

AND SUBSTITUTE "TEX". LINE 4, DELETE "70" AND

SUBSTITUTE "31-35". LINE5, DELETE "40" AND

SUBSTITUTE "46-60".

PAGE 4, PARA. 3.3.4, LINE 4, UNDER "PLY" COLUMN

DELETE "OR 3".

PAGE 4, PARA. 3.3.4, LINE 5, UNDER "PLY" COLUMN

DELETE "6" AND SUBSTITUTE "2 OR 3".

PAGE 5, PARA. 3.3.4.1, LINE 3, DELETE

"MIL-T-43548" AND SUNSTITUTE "A-A-50199".

PAGE 5, PARA. 3.3.6, DELETE THE FIRST SENTENCE

AND SUBSTITUTE: "THE COLLAR STAYS SHALL BE MADE

FROM POLYETHYLENE TEREPHTHALATE PLASTIC SHEET,

WITH A THICKNESS OF 0.010 (+/-0.001) INCH;

THE COLOR SHALL BE NATURAL (CLEAR OR

OPAQUE), AND TRANSPARENCY AND OPTICAL PROPERTIES

SHALL NOT APPLY."

PAGE 5, PARA. 3.3.7.1, LINES 10 AND 12, DELETE

"SOFTNER" AND SUBSTITUTE "SOFTENER"; LINE 12,

AFTER "SOFTENER" ADD "DRYER SHEETS"; LINE 13,

DELETE "EXCLUDING" AND SUBSTITUTE "EXCEEDING".

PAGE 6, AFTER PARA. 3.3.7.4 ADD THE FOLLOWING

PARA." "3.3.7.5 BAR CODE LABEL/TAG. EACH ITEM

SHALL BE INDIVIDUALLY BAR CODED WITH A

PAPER TAG FOR PERSONAL CLOTHING ITEMS. THE

PAPER USED FOR THE TAGS SHALL BE STANDARD

BLEACHED SULFATE HAVING A BASIS WEIGHT OF 100

POUNDS WITH A SMOOTH FINISH TO ACCEPT THERMAL

TRANSFER AND DIRECT PRINTING. THE TAGS SHALL

HAVE A HOLE AND SHALL BE ATTACHED TO EACH ITEM

BY A FASTENER, CLEARLY LEGIBLE AND READABLE BY

SCANNER. THE BAR CODING ELEMENT SHALL BE A 13

DIGIT NATIONAL STOCK NUMBER (NSN). THERE SHALL

BE A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC)

ASSIGNED FOR ALL NSN'S BY THE GOVERNMENT. THE

INITIALS "UPS" MUST APPEAR BENEATH THE CODE.

THE BAR CODES FOR NSN AND UPC SHALL BE A MEDIUM

TO HIGH DENSITY AND SHALL BE LOCATED SO THAT

THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT

IS FOLDED AND OR PACKAGED AS SPECIFIED. THE

LABEL'S LOCATION SHALL CAUSE NO DAMAGE TO THE

ITEM."

PAGE 9, OPER. 4(B), DELETE IN ITS ENTIRETY AND

SUBSTITUTE: "B. FOLD POCKET IN ACCORDANCE WITH

FOLD LINE INDICATED ON PATTERN AND HEM WITH TWO

ROWS OF STITCHING 1/4 INCH GAUGE WITH OUTER ROW

1/16 INCH FROM FOLDED EDGE."

PAGE 10, TABLE I MANUFACTURING REQUIREMENTS,

OPERATION 5(E), DELETE "40/6" UNDER "NDL" AND

"BOB/LPR" COLUMNS AND SUBSTITUTE "40/2 OR 3"

UNDER BOTH COLUMNS.

PAGE 10, OPERATION 5(E), LINE 2, DELETE "9/16"

AND SUBSTITUTE "5/8".

PAGE 11, BEFORE PARAGRAPH 7A., ADD "* NOTE: AS

AN ALTERNATE TO THE FOLLOWING INFORMATION,

COLLAR STAYS MAY BE SPOT LAMINATED TO THE

INTERLINING AND ELIMINATE THE USE OF THE COLLAR

STAY PIECES."

Page 14, operation 9a (formerly operation 9d), line 6, delete "finish 1/2 inch" and substitute "finish 1(+/-1/16) inch."

PAGE 16, OPER. 12.B., DELETE LAST SENTENCE AND

INSERT, "THE FACING SHALL BE TURNED TO THE

INSIDE AND FINISH 1-1/2 TO 1-3/4 INCHES WIDE."

PAGE 16, OPERATION 12.B., UNDER SEAM/STITCH TYPE

DELETE "LSK-2" AND ADD "LSAG-2".

PAGE 17, TABLE I, MANUFACTURING REQUIREMENTS,

OPERATION 14. DELETE IN ITS ENTIRETY AND

SUBSTITUTE: "14. SEW ON LABEL. FINISHED

APPEARANCE. WHEN CLOTH INDETIFICATION/

INSTRUCTION LABEL IS USED, IT SHALL BE

POSITIONED ON OUTSIDE OF SHIRT APPROXIMATELY

2-1/2 INCHES FROM THE FRONT FOLDED EDGE AND

NO MORE THAN 1-1/2 INCHES UP FROM THE BOTTOM FINISHED

EDGE OF THE SHIRT ON LEFT SIDE AS WORN."

PAGE 19, OPER. 17, SET COLLAR WITH SIZE LABEL,

"FINISHED APPEARANCE", LINE 6, DELETE "+/- 1/8"

AND SUBSTITUTE "+3/16, -1/8".

PAGE 21, AFTER OPERATION 21.B. ADD: "OR" "CUFFS

MAY BE ATTACHED IN ONE OPERATION PROVIDED THE

FINISHED APPEARANCE IS THE SAME AS SPECIFIED IN

"A" AND "B" ABOVE, AND THE ENDS OF THE ROW OF

STITCHING ARE BACKTACKED OR CROSSED WITH ANOTHER

LINE OF STITCHING: 301 LSE-1 12-16 70-2 70-2.

PAGES 23 AND 24, TABLE I MANUFACURING

REQUIREMENTS, OPERATION 22(B), (C), (D) AND (F),

DELETE ALL "40/6" UNDER "STCH/IN" AND "NDL"

COLUMNS AND SUBSTITUTE ON THE SAME LINES

"40/2 OR 3" UNDER "NDL" COLUMN AND "40/2 OR 3"

UNDER "BOB/LPR" COLUMN.

PAGE 24, TABLE I MANUFACTURING REQUIREMENTS,

OPERATION 23 (A), (B) AND (C), DELETE ALL "40/6"

UNDER "NDL" AND "BOB/LPR" COLUMNS AND SUBSTITUTE

"40/2 OR 3" UNDER BOTH COLUMNS.

PAGE 25, TABLE I MANUFACURING REQUIREMENTS,

OPERATION 23(D) AND (E), DELETE ALL "40/6" UNDER

"NDL" COLUMN AND ALL "40/" UNDER "BOB/LPR"

COLUMN AND SUBSTITUTE "40/2 OR 3" UNDER BOTH

COLUMNS.

PAGE 27, PARAGRAPH 3.7, FINISHED MEASUREMENTS, UNDER COLUMN FOR "NECK SIZE", UNDER

"SIZE 13", OPPOSITE COLUMN FOR "BREAST INCHES", DELETE "36" AND SUBSTITUTE "35".

PAGE 27, PARA. 3.7 FINISHED MEASUREMENTS,

TABLE II, SHIRT MEASUREMENTS UNDER "BACK LENGTH

INCHES 3/" IN LINE WITH "TOLERANCES" DELETE

"+1/2, -1/2" AND INSERT "+1, -1/2".

PAGE 27, PARA. 3.7, ADD THE FOLLOWING: "NECK

SIZE: 18-1/2; COLLAR LENGTH: 19; BREAST: 57;

BACK LENGTH: 31-3/4; SLEEVE LENGTH: SEE 1.2".

PAGE 27, FOOTNOTE 3/. LINE 1, AFTER "FROM"

DELETE "LOWER EDGE OF UNDERCOLLAR" AND

SUBSTITUTE "LOWER COLLARSTAND JOINING SEAM".

PAGE 27, PARA. 3.7, TABLE III, OPPOSITE "NECK

SIZE" - DELETE "15 TO 18 (INCLUSIVE) INCHES" AND

SUBSTITUTE "15 TO 18-1/2 (INCLUSIVE) INCHES."

PAGE 29, PARAGRAPH 5.1.1, DELETE AND

SUBSTITUTE: "LEVEL A. EACH FULLY BUTTONED

SHIRT SHALL BE FOLDED IN ACCORDANCE WITH

STANDARD PRACTICE TO APPROXIMATE DIMENSIONS

OF 14 BY 10-1/2 INCHES. THE FOLDED SHIRT SHALL

BE SECURED WITH NONCORROSIVE PINS OR CLIPS, AND

PLACED IN A POLYETHYLENE BAG APPROXIMATELY

14-1/2 INCHES LONG BY 11 INCHES WIDE, WITH A

1 INCH LIP ALONG THE OPEN 11-INCH DIMENSION.

THE POLYETHYLENE FLEXIBLE FILM SHALL BE

0.0015 INCH THICK. THE FINAL CLOSURE OF THE

BAG SHALL BE BY MEANS OF A TUCK OR REVEERSE FLAP

EACH BAG SHALL CONTAIN A LABEL (SEE 5.3.1)."

THE USE OF HEAT SEALING THE POLYETHLENE BAG

IS PROHIBITED."

PAGE 30, PARA. 5.4, ADD THE FOLLOWING AT END OF

PARA.: "THE GOVERNMENT ASSIGNED UNIVERSAL

PRODUCT CODE (UPC) MUST BE PLACED ON ALL

SHIPPING CARTONS ON WHICH THE NSN APPEARS."

(Ref. W2923) Additional Interim changes to Attachment 1A of MIL-S-3649G:

"Page 4 of 10, item number 24, delete: "Page 14, Table I, delete operations 9a and 9c in their entirety and after operation 9c, delete "Classes 2 and 3".

and substitute the following:

"Page 14, Table I, delete operations 9b and 9c in their entirety and after operation 9c, delete "Classes 2 and 3".

Page 5 of 10, after item number 34, add the following:

"35. Page 16, Table I, operation 12, delete operation in its entirety and substitute the following operation:

12. Make permanent crease in fronts.

a. Hard press and crease each front from the top to the bottom with a straight vertical crease in accordance with the marks on the pattern.

b. Apply an even continuous 1/16 inch silicone bead to the center of the pre-pressed crease in each front on the back side of the basic material."

Page 5 of 10, after the above change, add the following:

"36. Page 16, Table I, operation 13 title, delete "Classes 2 and 3)". (Re-number all subsequent items, i.e., item number 35 is now re-numbered as item 37, and ending with item number 55, since item number 48 is deleted below)."

Page 7 of 10, item number 48, delete the following: "Page 24, Table I, operation 22f, re-letter operation "22f" to "22b".