A01_VPM POWER CABLE REV -.pdf

ALTERED ITEM DRAWING

PIN: 18002A4046-000

CURRENT DESIGN ACTIVITY CAGE CODE: 12255

NAVSEA CRANE DIVISION

NAVAL SURFACE WARFARE CENTER, CRANE DIVISION

CRANE, INDIANA

CUI

CUI

CONTROLLED BY: MARCORSYSCOM

CONTROLLED BY: PEO/LS, PM GBAD

CUI CATEGORY: CTI, OPSEC

DISTRIBUTION STATEMENT: D

POC: FRAN BONNER FRANCIS.BONNER@USMC.MIL

TEH2023/07/31- INITIAL RELEASE ECP 22-03

.25

18.00

4X 1.50

LABEL A

5.4.

6.

7. 8.

NOTES:

1. FOR CABLE ASSEMBLY WIRING PRACTICES AND WORKMANSHIP REFER TO

IPC/WHMA-A-620 CLASS 3.

2. WIRING SHALL BE DONE IN ACCORDANCE WITH ELECTRICAL WIRING DIAGRAM.

3. MAKE FROM PART NUMBER 121287-001-30, MODIFY AS SHOWN.

4. MARKING REQUIREMENTS: LABEL LENGTHS SHALL NOT EXCEED 2.50 INCHES.

LABELS SHALL BE HEAT SHRINKABLE SLEEVES, PER SAE-AMS-DTL-23053/5

AND MARKING PROCEDURES SHALL BE IN ACCORDANCE WITH MIL-STD-130,

USING BLACK TEXT. REFER TO TABLE.

5. LABEL A SHALL BE LOCATED APPROXIMATELY 4.00 INCHES FROM CONNECTOR.

6. REMOVE 1.500 INCHES OF SHEATHING FROM THE CABLE, DO NOT DAMAGE THE WIRE INSULATION.

7. REMOVE 0.250 INCH OF INSULATION FROM THE CABLE, TIN WIRES USING FIND NO. 3.

8. SOLDERING SHALL BE IN ACCORDANCE WITH J-STD-001, USING FIND NO. 3.

9. FINISHED CABLE SHALL MEET THE FOLLOWING REQUIREMENTS: END TO END

CONTINUITY SHALL BE LESS THAN 1 OHM.

7. 8.

4. 5.

3.

WIRE DIAGRAM2.

BLK 12 AWG

RED 12 AWG

GRN 12 AWG

WHT 12 AWG

P1

LABEL MARKING INFORMATION

LABEL A

CBL ASSEMBLY,

VEHICLE POWER

LOW POWER

3 AR 96906 SN63PB37A SOLDER, ELECTRICAL, FLUX

CORE J-STD-006

2 AR 96906 M23053/5-109-4 HEAT SHRINK TUBING, 2:1,

YELLOW SAE-AS23053/5

1 1 2Y142 121287-001-30 CABLE ASSEMBLY, VEHICLE

POWER LOW POWER

8 7 6 5 4 3 2

C O

M P

U

TE

R G

E N

E R

A

TE

D

B

A

C

D

B

A

C

7 6 5 4 3

D

DESIGN ACTIVITY APPROVAL

APPROVED

REMOVE BURRS AND BREAK SHARP EDGES

MATERIAL

DO NOT SCALE THIS DRAWING

CONTRACT NO.

ENGINEERED BY

APPROVED BY

CHECKED BY

OF

SCALE WEIGHT SHEET

CAGE CODESIZE

TITLE

DWG NO. REV

ASME Y14.24, ASME Y14.34M, AND ASME Y14.35M APPLIES

FOR INTERPRETATION OF DRAWING ASME Y14.100,

USED ONNEXT ASSY

APPLICATION

DATEDRAWN BY

CAD MAINTAINED. CHANGES

SHALL BE INCORPORATED

BY THE DESIGN ACTIVITY.

DEPARTMENT OF THE NAVY

UNITED STATES MARINE CORPS

D 1:1

18002A404601365 -

CABLE ASSEMBLY, VPM

POWER, LOWER CURRENT

R. LIVINGSTON 2022/04/20

G. HENRY

S. CORBIN

B. BRADSHAW

M9545020WR-R0712

J. WILLS 1 1FOR INTERPRETATION OF DIMENSIONING

AND TOLERANCING SEE ASME Y14.5M 2009

18002B4001 18002C4001

18002A0000

FIND

NO.

QTY.

REQD.

CAGE

CODE

PART NO. OR

IDENTIFYING NO.

NOMENCLATURE OR

DESCRIPTION SPECIFICATION NOTE OR

REMARKS

PARTS LIST

DESCRIPTIONZONE

REVISIONS

APPROVEDDATEREV

DWG NO. REVSHT118002A4046 - 1

THREE PLACE (XXX)

UNLESS OTHERWISE SPECIFIED: ALL SURFACES

THIRD ANGLE PROJECTIONANGLES

TWO PLACE (XX)

ONE PLACE (X)

UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES

P. MIX

DISTRIBUTION STATEMENT D: DISTRIBUTION AUTHORIZED TO THE DEPARTMENT OF DEFENSE AND U.S. DOD CONTRACTORS ONLY; ADMINISTRATIVE AND OPERATIONAL USE, 15 NOV. 2018; OTHER

REQUEST SHALL BE REFERRED TO PEO LS(PM GBAD), 2200 LESTER STREET, QUANTICO,

VA 22134-5050.

WARNING: THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY THE

ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C. SEC 2751 ET SEQ.) OR THE EXPORT ADMINISTRATION ACT OF 1979 (TITLE 50, U.S.C. APP. 2401 ET SEQ.) AS AMENDED. VIOLATIONS OF THESE EXPORT LAWS ARE SUBJECT TO SEVERE CRIMINAL PENALTIES. DISSEMINATE IN ACCORDANCE WITH PROVISIONS

OF DOD DIRECTIVE 5230.25. 3.