Knox Lake - Dock Specification OhioBuys.pdf

The Ohio Division of Wildlife is soliciting bids for the construction and delivery of an ADA accessible fishing pier at Knox Lake Marina and Boat Ramp (south end) 1780 Buena Vista Dr., Fredericktown, OH 43019 with the following specifications. Bid does not include installation. Submitted bids must be for dock of specifications listed below.

Knox Lake Project Specifications

Materials Required

- One (1) 6’ wide x 20’ long aluminum gangway with dual-sided handrail and supplemental flotation

- One (1) Bulkhead Hinge Connection Kit

- Two (2) 6’2” wide x 20’ long floating docks

- Two (2) 8’2” wide x 20’ long floating docks

- Three (3) transition strips connecting docks

- Two (2) External Elongated Piling Guides o Pilings are not needed for this Pier, and will be provided by a separate vendor that installs the Pier.

- Fishing Handrail around perimeter of (2) 8’2” wide docks

BoardSafe Floating Dock

• 16” freeboard with no live load present

• 2.5” draft depth with no live load present

• 7” freeboard with 30psf live load

Figure 1: Dock Freeboard

• 50-Series Dock Frame o Rectangular aluminum extrusion o Measures 6.06” high by 3.77” wide o Weight of 3.69lb/lineal foot o Track in top surface of extrusion to allow for bolting accessories such as cleats (movable) and an external diverter plate to the top perimeter of dock.

o Channel on side of dock to allow for the attachment of “D” style rub rail.

Reference Figure 2.

Figure 2: Framing Detail

• All framing components to be Marine Grade 6061 or 6063 Aluminum.

• Fasteners are to be stainless steel

• All flotation is to be plastic encapsulated foam.

• Decking to be Gray Composite with a span rating of 24” on center o 5/4” x 6” nominal sizing

• Decking to be attached using the TimberStrong fastening system, meaning there are no fasteners in the deck surface. Reference Figure 3.

o Fastener is to be mechanically attached to each corresponding deck board o Embedment into the deck board is a minimum of 1-inch and located directly over each joist o Attachment at each joist is to be with one #10 stainless steel, self-tapping screw, placed through the black PVC TimberStrong fastener and into the corresponding joist

• Dock-to-Dock connections to have seamless transitions.

o A flat aluminum strip should be used to attach dock sections together. The strip is to be held in place by a bolted connection through the strip and into the 50 series extrusion. Aluminum splice plates should be installed on the vertical face of the docks, under the rub rail.

• A hinge connection is to be provided on the dock closest to the bulkhead for the attachment to the gangway and kayak chute.

o The hinges are to be slid in the slot on the side of the 50 series dock frame.

• Toe kicks should be provided for all open sides of the 8-foot by 16-foot docks.

• External pile guides to be fastened to outside channel on floating docks.

Gangway

• All framing components to be Marine Grade 6061 or 6063 Aluminum.

• Fasteners are to be stainless steel

• Flotation is to be plastic encapsulated foam.

o Supplemental flotation is required to be added to the bottom of the gangway to provide a freeboard of 16” to 18” (with no live load present)

• Railing to be located on two sides, at a height of 42-inches.

• An intermediate handrail is to be located at 34-inches.

• Decking to be 12-inch wide, raised rib, knurled aluminum, welded in place.

• Integrated hinges are to be located at the top and bottom of the gangway.

Hinges are to be mechanically attached; welded connections will not be permitted.

o 1 ¼” schedule 40 stainless steel pipe hinge pins with stainless steel hardware

• A 4-inch toe kick should be provided on both sides of gangway.

Bulkhead Mounting Kit

• Aluminum angles with integrated attachment of hinges. Reference Figure 4.

o Hinges are to be mechanically attached; welded connections will not be permitted.

o 1 ¼” schedule 40 pipe hinge pins with stainless steel hardware

• Stainless steel attachment hardware for mounting to existing concrete bulkhead.

o ½” diameter wedge bolts for vertical face.

o 3/8” diameter wedge sleeves and bolts for attachment of top of angle.

Figure 4: Bulkhead Mounting Angle Detail

20'-0" 20'-0" 8'-2"

20'-0"

6'-2"

6'-0" 5'-0"

TREAD 40'-0"

68'-8"

3 1 2 "

OD PIPE

PILES

24'-0"

3 1 8 "

TYP

8'-11"

TYP

REF

12'-0"

20'-0"

3'-0"2'-6" 5"

2'-6"

TYP

40'-2 3 4 "

3'-1"

3'-6"2'-10"

1'-4"

FREE-BOARD UP TO

1:12 PITCH

A

WATER LEVEL

4'-4 5 16 "

5'-0"

6'-4"

40'-0"

14'-1 1

2 " TYP NEAR SIDE11'-2 1

2 " TYP FAR SIDE

3D REF VIEW

TYP TOE

KICK

DOCK TO DOCK

MOUNTING ANGLES

DOCK TO DOCK

THRESHOLDS

8FT 2IN X 20FT

FLOATING DOCKS

(2) SUPPLIED

FISHING RAILING

AROUND FLOATING

DOCKS

3 1/2" DIA OD

PIPE PILES W/

ELONGATED

GUIDES

(2) SUPPLIED

TOE RAILS

TOE RAILS

BULKHEAD

MOUNTING

ANGLE

GANGWAY

MACHINED

& KNURLED

NON-SLIP TREADS

HANDRAILS

FLOATS

COMPOSITE

DECKING

6FT X 20FT

FLOATING DOCKS

(2) SUPPLIED

DOCK TO DOCK

THRESHOLDS

DETAIL A

HINGE PIN

(6) 5/8" DIA HOLES X 7" DEEP

FOR 5/8" WEDGE ANCHORS

FOUNDATION

(5) 1/2" DIA HOLES X 1 5/8" DEEP

FOR 3/8" THREADED INSERTS

BULK HEAD

ANGLEGANGWAY

TREAD

SHEET NUMBER

PROJECT INFORMATION

DATE

DRAWN BY

APPROVAL

# DATE REVISION

FISHING DOCK

KNOX LAKE