Item Description - Cranes - FINAL EXT T.pdf

ACCO Bridge Crane Hoist Rails

Item Description

Required specifications:

• Two (2ea) ½ ton capacity, ACCO Motorized single girder underhung patented motor driven crane, Part Number 585.2003-12.5, with the following specifications:

o Operating flange 3.33 inch louden patented track, part number 604.924 o 12 ft and 6 inch span between runways o 1 ft and 0 inch overhang on each end o 14 ft and 6 inch overall length o Rigid track festooning electrification for operation of hoist and trolley o 4-wheel 5000 lbs end truck assembly o 6 ft and 9 inch overall end truck length with rubber bumper both ends o 125 fpm max. travel speed o 2ea 1/2 HP motors o Inverter duty with manual brake release o Variable frequency crane control o G+ series 4 inverter o Voltage 208V 3Phase 60Hz – 110 volt control o Safety yellow enamel paint finish o No paint on running treads o Maximum crane weight 2000 lbs o 2 ft and 8 inch headroom treadline of runway to saddle of hook

• Two (2 ea) 1/2-Ton Rated, ACCO Lift Electric chain hoist with motorized trolley, Model

2130130-VFD-208, to include:

o Voltage 208V 3Phase 60Hz o Operating flange 3.33 inch louden patented track o 30 feet lift height o 15 FPM hoist lift speed VFD o 3ft – 6 inch max headroom from rail trade line to saddle of hook at high o Lifting Speed 21/7 fpm, 2 speed variable frequency o Hoist Motor – 2.4 HP, 9.2 Amps o Suspension lug mounted to motorized trolley o Trolley speed 50/17 fpm, 2 speed variable frequency drive o Trolley Motor – .54 HP, 3.3 Amps o Enclosure rating NEMA 12 o Chain Container o Tagline tow arm o Thermal motor protection o Upper and lower Limit switch o Hoist H3 Duty class o Mechanical Load Brake o Overload alert o Standard power coat orange paint finish o Hoist/Trolley Max. weight 300 lbs o HBC-Radiomatic Micron 7 radio remote control transmitter and receiver

▪ 3-motion

▪ Start button

▪ Crane North / South

▪ Hoist up / down

▪ Trolley East / West

▪ Red E-Stop button

▪ Operator controlled warning horn

▪ Operating and battery status display

▪ Spare transmitter

▪ Radio control with rechargeable batteries and chargers

• Visual warning light activated with crane movement (flashing strobe light).

• Each crane, trolley and hoist set motion to be controlled from 1ea set of transmitter

• Eight (8ea) ACCO part number 604.924, Louden Supertrack patented Girder with the following specifications:

o 26ft-6 inch long o depth 9 inches o 24 lb/feet o bottom flange width 3.33” o Standard surface preparation, gray primer paint o

• Four (4ea) 2 Ton, ACCO Speedway Wire Rope Hoist, Model Number X1W02D025-15M2D1

• Eight (8 ea) End stops, angle type ACCO Part Number 607.5030 end stop assembly including mounting hardware.

• Four (4ea) Web Splice plate assembly (pair) ACCO Part Number 607.5011 including mounting hardware, Gray primer paint.

• Shall include delivery of design drawings and specifications for approval prior to production start.

• Shall include copies of interconnect schematic, installation manual, service manual, and operation manual.

• Bridge shall be labeled with its rated weight load capacity on both sides.

• The radio remote control shall operate all motions of the 585 crane and electric chain hoist lift with motorized trolley.