ITB 2025-1100-0054 Replacement Boat and Trailer for Ketchikan.pdf

STATE OF ALASKA

INVITATION TO BID (ITB)

KETCHIKAN ALUMINUM BOAT AND TRAILER

ITB 2025-1100-0054

ISSUED 8/15/24

THE ALASKA DEPARTMENT OF FISH AND GAME DIVISION OF WILDLIFE CONSERVATION IS SOLICITING BIDS FOR A NEW 24-FOOT (APPROX 26’ LOA) WELDED ALUMINUM MANAGEMENT/RESEARCH VESSEL AND A

GALVANIZED STEEL OR ALUMINUM BOAT TRAILER FITTED WITH DISC BRAKES.

IMPORTANT NOTICE: If you received this solicitation from the State of Alaska’s “Online Public Notice” web site, you must register with the procurement officer listed below if you desire to receive notification of subsequent amendments to the solicitation.

BIDDER'S NOTICE: By signature on this form, the bidder certifies that they comply with the following:

(1) the bidder has a valid Alaska business license or will obtain one prior to award of any contract resulting from this ITB. If the bidder possesses a valid

Alaska business license, the license number must be written below or one the following forms of evidence must be submitted with the bid:

• a canceled check for the business license fee;

• a copy of the business license application with a receipt date stamp from the State's business license office;

• a receipt from the State’s business license office for the license fee;

• a copy of the bidder’s valid business license;

• a sworn notarized affidavit that the bidder has applied and paid for a business license;

(2) the price(s) submitted was arrived at independently and without collusion, under penalty of perjury, and that the bidder is complying with:

• the laws of the State of Alaska;

• the applicable portion of the Federal Civil Rights Act of 1964;

• the Equal Employment Opportunity Act and the regulations issued thereunder by the state and federal government;

• the Americans with Disabilities Act of 1990 and the regulations issued thereunder by the state and federal government;

• the bid will remain open and valid for at least 90 days;

• all terms and conditions set out in this Invitation to Bid (ITB).

If a bidder does not hold an Alaska Business License (1) at the time designated in the ITB for opening the state will disallow the Alaska Bidder Preference.

Bids must also be submitted under the name as appearing on the bidder’s current Alaska business license in order to receive the Alaska Bidder Preference. If a bidder fails to comply with (2) of this paragraph, the state may reject the bid, terminate the contract, or consider the contractor in default.

DEPARTMENT OF FISH AND GAME

DIVISION OF WILDLIFE CONSERVATION COMPANY SUBMITTING BID

AUTHORIZED SIGNATURE

PROCUREMENT OFFICER:

HOLLIE ROSELLE PRINTED NAME

PHONE: (907) 465-8731

EMAIL: HOLLIE.ROSELLE@ALASKA.GOV DATE

STATE OF ALASKA – INVITATION TO BID ITB 2025-1100-0054

2 Revised 3/7/2024

TABLE OF CONTENTS

SECTION 1. INTRODUCTION & INSTRUCTIONS

SEC. 1.01 PURPOSE OF THE ITB

SEC. 1.02 BUDGET

SEC. 1.03 DEADLINE FOR RECEIPT OF BIDS

SEC. 1.04 PRIOR EXPERIENCE

SEC. 1.05 REQUIRED REVIEW

SEC. 1.06 QUESTIONS PRIOR TO DEADLINE FOR RECEIPT OF BIDS

SEC. 1.07 SITE INSPECTION

SEC. 1.08 RETURN INSTRUCTIONS

SEC. 1.09 ASSISTANCE TO BIDDERS WITH A DISABILITY

SEC. 1.10 AMENDMENTS TO BIDS

SEC. 1.11 AMENDMENTS TO THE ITB

SEC. 1.12 ITB SCHEDULE

SEC. 1.13 PRE-BID CONFERENCE/TELECONFERENCE

SEC. 1.14 ALTERNATE BIDS

SEC. 1.15 SUPPORTING INFORMATION

SEC. 1.16 FIRM, UNQUALIFIED, AND UNCONDITIONAL OFFER

SECTION 2. SCOPE OF WORK AND CONTRACT INFORMATION

SEC. 2.01 SCOPE OF WORK – SPECIFICATIONS

SEC. 2.02 CONTRACT TERM

SEC. 2.03 CONTRACT TYPE

SEC. 2.04 PAYMENT FOR STATE PURCHASES

SEC. 2.05 PROMPT PAYMENT FOR STATE PURCHASES

SEC. 2.06 CONTRACT ADMINISTRATION

SEC. 2.07 CONTRACT PRICE ADJUSTMENTS

SEC. 2.08 JOINT VENTURES

SEC. 2.09 RIGHT TO INSPECT PLACE OF BUSINESS

SEC. 2.10 F.O.B. POINT

SEC. 2.11 INSPECTION & MODIFICATION - REIMBURSEMENT FOR UNACCEPTABLE DELIVERABLES

SEC. 2.12 EQUIPMENT INSPECTION

SEC. 2.13 NEW EQUIPMENT

SEC. 2.14 REMANUFACTURED/RECONDITIONED EQUIPMENT

SEC. 2.15 LEMON CLAUSE

SEC. 2.16 DISCONTINUED ITEMS

SEC. 2.17 LIQUIDATED DAMAGES

SEC. 2.18 SHIPPING DAMAGE

SEC. 2.19 CONTRACT CHANGES – UNANTICIPATED AMENDMENTS

SEC. 2.20 CONTINUING OBLIGATION OF CONTRACTOR

SEC. 2.21 BILLING INSTRUCTIONS

SEC. 2.22 ESTIMATED QUANTITIES

SEC. 2.23 WARRANTY

SEC. 2.24 NONDISCLOSURE AND CONFIDENTIALITY

SEC. 2.25 INDEMNIFICATION

SEC. 2.26 INSURANCE

3 Revised 3/7/2024

SECTION 3. BID FORMAT AND CONTENT

SEC. 3.01 BID FORMS

SEC. 3.02 BID BOND – PERFORMANCE BOND – SURETY DEPOSIT

SEC. 3.03 PRICES

SECTION 4. EVALUATION AND CONTRACTOR SELECTION

SEC. 4.01 EVALUATION OF BIDS

SEC. 4.02 APPLICATION OF PREFERENCES

SEC. 4.03 ALASKA BIDDER PREFERENCE

SEC. 4.04 ALASKA VETERAN PREFERENCE

SEC. 4.05 USE OF LOCAL FOREST PRODUCTS

SEC. 4.06 LOCAL AGRICULTURAL AND FISHERIES PRODUCT PREFERENCE

SEC. 4.07 ALASKA PRODUCT PREFERENCE

SEC. 4.08 EMPLOYMENT PROGRAM PREFERENCE

SEC. 4.09 ALASKANS WITH DISABILITIES PREFERENCE

SEC. 4.10 PREFERENCE QUALIFICATION LETTER

SEC. 4.11 EXTENSION OF PRICES

SEC. 4.12 METHOD OF AWARD

SEC. 4.13 CONTRACTOR SELECTION PROCESS

SEC. 4.14 NOTICE OF INTENT TO AWARD

SECTION 5. GENERAL PROCESS AND LEGAL INFORMATION

SEC. 5.01 INFORMAL DEBRIEFING

SEC. 5.02 ALASKA BUSINESS LICENSE AND OTHER REQUIRED LICENSES

SEC. 5.03 AUTHORITY

SEC. 5.04 COMPLIANCE

SEC. 5.05 SUITABLE MATERIALS, ETC

SEC. 5.06 SPECIFICATIONS

SEC. 5.07 BRAND SPECIFIC

SEC. 5.08 ITEM UPGRADES

SEC. 5.09 WORKMANSHIP AND MATERIALS

SEC. 5.10 CONTRACTOR SITE INSPECTION

SEC. 5.11 ORDER DOCUMENTS

SEC. 5.12 HUMAN TRAFFICKING

SEC. 5.13 RIGHT OF REJECTION

SEC. 5.14 STATE NOT RESPONSIBLE FOR PREPARATION COSTS

SEC. 5.15 DISCLOSURE OF BID CONTENTS

SEC. 5.16 ASSIGNMENTS

SEC. 5.17 FORCE MAJEURE (IMPOSSIBILITY TO PERFORM)

SEC. 5.18 DEFAULT

SEC. 5.19 DISPUTES

SEC. 5.20 SEVERABILITY

SEC. 5.21 CONTRACT CANCELLATION

SEC. 5.22 GOVERNING LAW; FORUM SELECTION

SEC. 5.23 QUALIFIED BIDDERS

SEC. 5.24 FEDERALLY IMPOSED TARIFFS

SEC. 5.25 PROTEST

SECTION 6. ATTACHMENTS

4 Revised 3/7/2024

SEC. 6.01 ATTACHMENTS

5 Revised 3/7/2024

SECTION 1. INTRODUCTION & INSTRUCTIONS

SEC. 1.01 PURPOSE OF THE ITB

The Department of Fish and Game, Division of Wildlife Conservation, is soliciting bids for a new 24-foot (Approx 26’ LOA) welded aluminum management/research vessel and a galvanized steel or aluminum boat trailer fitted with disc brakes. Please see the attached scope of work (section 2.01) for required specifications.

SEC. 1.02 BUDGET

Bids priced at more than $175,000 will be considered non-responsive.

Payment for the contract is subject to funds already appropriated and identified.

SEC. 1.03 DEADLINE FOR RECEIPT OF BIDS

Bids must be received no later than 2:00P.M. Alaska Time on 9/05/24, at which time they will be publicly opened.

Late bids or amendments will be considered non-responsive and will not be opened or accepted for evaluation.

SEC. 1.04 PRIOR EXPERIENCE

No specific minimums have been set for this ITB.

SEC. 1.05 REQUIRED REVIEW

Bidders shall carefully review this ITB for defects and questionable or objectionable material. Comments concerning defects and questionable or objectionable material in the ITB should be made in writing and received by the procurement officer at least ten days before the deadline for receipt of bids. This will allow time for an amendment to be issued if one is required. It will also help prevent the opening of a defective bid, upon which award cannot be made, and the resultant exposure of bidders' prices.

SEC. 1.06 QUESTIONS PRIOR TO DEADLINE FOR RECEIPT OF BIDS

All questions must be in writing and directed to the procurement officer. The interested party must confirm telephone conversations in writing. Two types of questions generally arise. One may be answered by directing the questioner to a specific section of the ITB. These questions may be answered over the telephone. Other questions may be more complex and may require a written amendment to the ITB. The procurement officer will make that decision.

SEC. 1.07 SITE INSPECTION

Not applicable to this ITB.

SEC. 1.08 RETURN INSTRUCTIONS

Submitting bids via email is preferred by ADF&G.

If submitting your bid via email, the entire bid may be emailed to dfg.contracting@alaska.gov and must contain the ITB number in the subject line of the email. The maximum size of a single email (including all text and attachments) that can be received by the state is 20mb (megabytes). If the email containing the bid exceeds this size, the bid must be sent in multiple emails that are each less than 20 megabytes and each email must comply with the requirements described above.

mailto:dfg.contracting@alaska.gov

6 Revised 3/7/2024

Please note that email transmission is not instantaneous. Like sending a hard copy bid, if you are emailing your bid, the state recommends sending it enough ahead of time to ensure the email is delivered by the deadline for receipt of bids.

It is the bidder’s responsibility to contact the issuing agency at 907-465-6871 to confirm that the entire bid has been received. The state is not responsible for unreadable, corrupt, or missing attachments.

Bidders can submit bids via mail, if submitting by mail please submit one hard copy of their entire bid, in writing, to the procurement officer in a sealed package. The sealed bid package must be addressed as follows:

Department of Fish and Game Division of Administrative Services - Procurement

Attention: Hollie Roselle Invitation to Bid (ITB) Number: 2025-1100-0054

ITB Title: Aluminum boat and trailer

If using U.S. mail, please use the following address:

P.O. BOX 115526

JUNEAU, AK

99811-5526

If using a mail courier, please use the following address:

1255 W 8th St.

Juneau, AK 99801

SEC. 1.09 ASSISTANCE TO BIDDERS WITH A DISABILITY

Bidders with a disability may receive accommodation regarding the means of communicating this ITB or participating in the procurement process. For more information, contact the procurement officer no later than ten days prior to the deadline for receipt of bids.

SEC. 1.10 AMENDMENTS TO BIDS

Amendments to or withdrawals of bids will only be allowed if acceptable requests are received prior to the deadline that is set for receipt of bids, in accordance with 2 AAC 12.140. No amendments or withdrawals will be accepted after the deadline unless the delay is due to an error of the contracting agency, in accordance with 2 AAC 12.160.

SEC. 1.11 AMENDMENTS TO THE ITB

If an amendment is issued before the deadline for receipt of bids, the amendment will be posted on the State of Alaska Online Public Notice (OPN) website. The link to the posting of the amendment will be provided to all who were notified of the ITB and to those who have registered with the procurement officer after receiving the ITB from the OPN.

7 Revised 3/7/2024

SEC. 1.12 ITB SCHEDULE

The ITB schedule below represents the State of Alaska’s best estimate of the schedule that will be followed. If a component of this schedule, such as the deadline for receipt of bids, is delayed, the rest of the schedule may be shifted accordingly. All times are Alaska Standard Time (AST).

ACTIVITY TIME DATE

Issue Date / ITB Released 8/15/2024 Deadline for Receipt of Bids / Bid Due Date 9/05/2024 Notice of Intent to Award 9/12/2024 Contract Issued 9/22/2024

This ITB does not, by itself, obligate the state. The state's obligation will commence when the contract is approved by the Commissioner of the Department of Fish and Game, or the Commissioner's designee. Upon written notice to the contractor, the state may set a different starting date for the contract. The state will not be responsible for any work done by the contractor, even work done in good faith, if it occurs prior to the contract start date set by the state.

SEC. 1.13 PRE-BID CONFERENCE/TELECONFERENCE

Will not be held for this ITB.

SEC. 1.14 ALTERNATE BIDS

Bidders may only submit one bid for evaluation. In accordance with 2 AAC 12.830 alternate bids (bids that offer something different than what is asked for) will be rejected.

SEC. 1.15 SUPPORTING INFORMATION

Provided a bid meets the requirements for a definite, firm, unqualified, and unconditional offer, the state reserves the right to request supplemental information from the bidder, after the bids have been opened, to ensure that the products or services offered completely meet the ITB requirements. The requirement for such supplemental information will be at the reasonable discretion of the state and may include the requirement that a bidder will provide a sample product(s) so that the state can make a first-hand examination and determination.

A bidder's failure to provide this supplemental information or the product sample(s), within the time set by the state, may cause the state to consider the offer non-responsive and reject the bid.

SEC. 1.16 FIRM, UNQUALIFIED, AND UNCONDITIONAL OFFER

To be responsive a bid must constitute a definite, firm, unqualified and unconditional offer to meet all the material terms of the ITB. Material terms are those that could affect the price, quantity, quality, or delivery. Also included as material terms are those which are clearly identified in the ITB, and which must be complied with at risk of bid rejection for non-responsiveness.

8 Revised 3/7/2024

SECTION 2. SCOPE OF WORK AND CONTRACT

INFORMATION

SEC. 2.01 SCOPE OF WORK – SPECIFICATIONS

TECHNICAL SPECIFICATIONS:

The following technical specifications identify the State of Alaska, Fish and Game, Division of Wildlife Conservation, (the State’s) requirements for a new 24-foot (Approx 26’ LOA) welded aluminum management/research vessel. The vessel will be used to support survey, inventory, and monitoring of game species in southern Southeast Alaska. We use this boat to access shore drop off locations which sometimes involves navigating through shallow waters. The boat must be able to cut through waves adequately while balancing the need for access to shallow waters. We commonly drop staff off on shore from the bow or anchor out and paddle kayaks into shore.

PERFORMANCE REQUIREMENTS:

The Contractor shall deliver a vessel that meets the following performance requirements:

The boat shall be equipped with a forward cabin providing reasonable accommodations for up to 6 people and gear storage. The aft deck will provide a minimum of 80 inches (length) of clear usable space.

The vessel and its components shall be suitable for operation in Southeast Alaska in all seasons. The vessel must successfully operate in the following environmental conditions: Ambient air temperatures: 80 deg F to 0 deg F, water temperatures between 30 deg F and 55 deg F., winds speeds between 0 and 40 knots, and wave heights between 0 and 6 feet.

The boat shall be constructed of highly durable marine grade materials, suitable for extended field operations by State management staff in Southeast Alaska waters. All components provided by the contractor shall be new.

The delivered boat will comply with all United States Coast Guard (USCG) requirements.

VESSEL AND CABIN ARRANGEMENT:

• The vessel shall have a fully enclosed watertight aluminum cabin located forward on the vessel with a sliding locking door to aft deck.

HULL:

• Length. Hull length (transom to bow) shall be 24 feet not including the extended transom engine bracket/swim step. Total length including the engine bracket to be about 26 feet.

• Beam Overall. Beam of the vessel should be between 102 - 107 inches depending on what is necessary for twin 150’s with a 20 hp kicker.

• Side Height. The side height shall be at least 36 inches.

• Aluminum. Hull plate and chines shall be at a minimum 1/4” and a minimum of 5000 series aluminum, sides shall be at a minimum 3/16” 5000 series aluminum or better, transom shall be at a minimum 1/4” 5000 series

9 Revised 3/7/2024 aluminum or better. Deck plate shall be a minimum of 1/8” diamond plated aluminum. Hull will have one to two running strikes depending on what is appropriate for build.

• Hull design will be modified V with between a 14-18 degree deadrise depending on what the builder believes is best to strike a balance between cutting through waves and having a shallow draft. The vessel will be designed with a self-bailing deck. Boat will be well suited for boating in inside waters and able to make shallow water drop offs on rocky shorelines, or beaching on gravel/sand.

• Front deck at gunnel height with storage space below accessible from cabin. Hand rails for walk around cabin to the bow, providing a walk through at the bow. Ideally, shape of bow at deck level will be designed to provide maximum room for standing. Small cleat welded to keel of the bow just above the bracket for hooking up the trailer winch hook, safety chain, and bow line, which acts as a foothold for getting on and off the boat from the tip of the bow. The cleat will be out of the way of the bow stop on the trailer where the keel of the boat rests.

Some sort of anti-slip material will be applied to top of cleat for grip.

• Continuous welds shall be utilized on all hull chines.

• Freeing ports/Scuppers. The vessel shall be provided with adequate scuppers located at the aft end of the vessel, in order to rapidly clear water off of the main deck. Scuppers on the stern will have a one-way flap or valve to prevent flooding when reversing.

• Engine Mounting. Engines shall be mounted on the engine bracket with space for a small ladder that can be folded up when moving, and folded down for entry to the boat from the water in an emergency. Ladder will be mounted on the port side of the engine bracket. A non-skid epoxy paint or equivalent should be applied to ladder steps for grip. The engine bracket should be covered with non-slip material. The engine bracket will be used to enter and exit kayaks and shall be provided with suitable mounting surface for two 150 hp Honda four-stroke outboards with appropriate shaft length and enough space for a 20 hp Honda kicker that does not hit trim tabs. All mounting surfaces and/or mounting brackets shall be specially re-enforced to handle engine loads and forces. Engine bracket length shall be 36 inches in length as measured from back of the hull transom, optimized for maximum engine performance and handling. Bids offering internal motor well or direct to transom mount engines will be rejected as nonresponsive.

• Transducer Brackets. One bracket on the back of the Engine mount.

• Transom door. Watertight door through the transom on the starboard side. This will allow easy access to get in and out of the water from a Kayak, to the engine bracket, and into the boat. Rials no less than one inch outside diameter will be mounted on both port and starboard sides of the transom running from the top of the gunnel down to where the transom meets the engine bracket with a space between the bar and the transom of 2-3 inches. Bars will be strong enough to bear the weight a 250 pound person leveraging their weight on the bar to pull them selves out of a Kayak or the water. Rails will be mounted parallel to the side of the boat, not perpendicular. Non-skid epoxy or equivalent should cover bars for grip.

• Storage. Built in storage on the transom (minus the door area) 16 to 20 inches in width for dual batteries along bottom section complete with access hatches and fish box type storage on upper section complete with watertight access hatch(es). One cut away section for access to racor water separator fuel filter and fuel tank valve manifold. Build in open storage on port and starboard sides of the aft end of boat along sidewalls.

10 Revised 3/7/2024

• Flush watertight access hatches to all void spaces under deck.

• Cleats. A minimum of six (6) 8-inch mooring cleats (3 port and 3 starboard) shall be installed.

• Automatic anchor with line, motor, etc., recessed inside bow storage area. Self-bailing if possible so water does not run into storage area and pool.

• Zincs. Two bolt-on hull zincs shall be installed to prevent corrosion on rear of engine bracket.

• Paint. Aluminum compatible non-skid epoxy or equivalent paint shall be applied to the main and fore decks, and the gunnel.

• Anti-fouling paint for reducing growth of algae on boat. Paint shall cover the entire bottom of boat up to natural waterline on side of boat. Color: blue

CABIN:

• Welded aluminum cabin, not to be less than 80 inches wide and 90 inches long, minimum 80 inch inside height at center. All welds must be watertight. Locking sliding door with window on aft side of cab centered.

• Cabin will be positioned forward with forward canted windows and windshield wipers mounted at the top of each window.

• Cabin roof will be equipped with full-length pipe handrails, no less than 1” outside diameter, port and starboard. Two additional full-length handrails inside cabin mounted overhead with a minimum clearance of 76 inches from the deck. Vertical handrail mounted next to door on inside back wall of cabin. Vertical handrails running from gunnel to roof will be mounted or integrated onto the aft starboard and port outside corners of the cabin. Rails will be suitable and strong enough to mount two kayaks on roof.

• No less than 10-inch-wide walk-around gunnels outside cabin. One small step on each side behind cabin for access to gunnel from back deck.

• Helm will be installed on starboard/forward side of cabin. The helm and controls will be positioned so boat can be comfortably operated while standing.

• Cabin material shall be at least 1/8” 5000 series aluminum. Inside surfaces covered with neutral colored suitable material (not carpet) to insulate and reduce condensation.

• Two or three forward facing windows, 1 or 2 windows on each side of cab with the forward window sliding, 2 fixed rear wall windows (one on port and one on starboard with on in sliding door).

• Sliding cabin door. Door shall include a fixed window, door handle, and be lockable with key included.

• All fixed windows to be rubber framed.

• All sliding windows to be aluminum framed and should lock in closed position.

• Seating in the cabin shall include 2 air cushioned (shock absorbing) seats positioned on forward port and starboard sides (captain and co-captain) in front and 2 center facing bench seats with storage, one on each side aft. Forward seats shall be mounted on raised pedestal, with storage underneath, so operator can sit

11 Revised 3/7/2024 comfortably and be at the same height as when standing. Foot rests will be mounted on bulkhead in front of front seats so operator and forward passenger can sit comfortably. All seats should be cushioned and fully upholstered.

• Passenger side glove box type compartment built into dash with handle above.

• Wallas 22GB Diesel 2.2kW Variable Power Forced Air Heater or equivalent heater, vented to outside, mounted in the cabin aft. All necessary hoses and regulator to attach fuel from storage located under floor with fuel cap integrated into gunnel with screw in watertight cap.

• Radar Arch/Tower on cabin roof located forward spanning the width of the cabin with weather proof port for electronics cables. At least 16 inches tall to fit kayaks underneath.

DECK:

• Deck shall be self-bailing (located above waterline with normal working loads), connected watertight to hull, and flush from cabin to transom.

• Self-bailing scuppers or pipe drains shall be provided. See “Freeing Ports/Scuppers” in Hull Section.

• Forward deck covered with non-skid paint, two handrails, one on either side of bow extending back along sides to aft of the cabin. Rails open off tip of bow to allow entry and exit from bow.

MECHANICAL:

• Operator control station will be located in forward, starboard side of cabin. Engine controls shall be mounted on an angled or horizontal surface, not vertical surface, with adequate space between steering wheel and throttle controls. Wheel will have a doorknob mounted for ease of turning.

• 1-2 welded aluminum or stainless-steel fuel tanks (1/8” 5000 aluminum or better), located below deck, minimum of 130 gallons total capacity, with baffles, vent hose located at the high point of tank, fuel sender and console-mounted gauges.

• USGS approved fuel lines and dual selectable water/fuel separator filters (if two fuel tanks).

• Two (2) 3,700 GPH minimum bilge pumps, both automatic bilge pumps with 3-way switches to be positioned on dash.

•Appropriate size trim tabs mounted on each side of transom, control switch(s) at helm.

ELECTRICAL:

• USCG approved navigation and anchor lights. Anchor light mounted in a way to keep top of cabin clear for securing kayaks to roof.

• USCG approved horn with switch or bottom on consol.

• Instrument panel shall include:

• Minimum of ten, water-resistant rocker style breaker protected switches located at helm for control of electrical accessories. Switches will be mounted on a hinged panel for easy access.

12 Revised 3/7/2024

• All wiring and electronics cables positioned for easy access in case of maintenance and repair.

• Gauges for two Honda 150s will include tachometer; oil pressure; engine temperature; fuel flow meter

• Fuel gauge (s).

• Forward windows equipped with two (2 or 3, depending on number of windows) 12V heavy duty variable speed pantograph equipped windshield wipers, one on the port side window and one on the starboard side window. The wipers will be individually switched and mounted at the top of the window.

• Two 12V deep cycle marine batteries with suitable non-metallic boxes, and high-quality battery selection switches and charging relay. Batteries shall be installed in an adequately ventilated space to prevent the buildup of gas.

• Two (2) 12VDC de-fogging fans, to be installed for port and starboard windshields.

• A minimum of two (2) interior LED lights shall be installed in the cabin.

• CO detector mounted inside cabin at appropriate height to detect CO.

• Dual USB charging ports mounted on console

ELECTRONICS:

• Garmin GPSMAP 1243xsv with 12-inch screen, Garmin Navionics+, with Alaska charts installed.

• Garmin GMR 18 HD3 Radome installed on radar tower.

• Garmin GT36 transducer installed on transom.

• Garmin VHF Fixed-Mount VHF Radio with AIS and NMEA 2000 Network, installed on console, and hooked up to external VHF antenna.

• VHF antenna mounted on outside of cabin with fold down option.

PROPULSION

• Twin (2) Honda four stroke outboards (150hp ea. minimum), appropriately sized to meet minimum performance requirements.

• Rigging package to include digital gauges, electronic control, harnesses, cables, and key switches.

• Complete hydraulic steering package including one helm, steering ram, steering wheel, and all hoses and hardware.

• Stainless steel propellers of appropriate size and pitch for each motor.

MISCELLANEOUS:

• The contractor shall provide guarantees for the workmanship, USCG compliance, interface of hardware capabilities, all equipment booklets, and operators’ handbook.

13 Revised 3/7/2024

• Any equipment or procedures of a critical nature shall be placarded in a very visible manner.

• All breakers and switches/valves shall be labeled.

BOAT TRAILER:

• The contractor shall provide a galvanized steel or aluminum boat trailer fitted with disc brakes (EZ Loader or equivalent). Trailer shall be set up and properly fitted to boat hull. The trailer shall have a minimum of two axles, be correctly sized for the combined vessel, 1,500 lbs of gear and fuel and trailer weight. The trailer will have a hand winch and suitable tie downs for securing the vessel.

SEC. 2.02 CONTRACT TERM

The length of the contract will be from the date the contract is awarded and signed and shall end the date the items have been delivered and the vendor has been paid.

SEC. 2.03 CONTRACT TYPE

This contract is an Goods and none – professional service contract.

SEC. 2.04 PAYMENT FOR STATE PURCHASES

No payment will be made until the contract is approved by the Commissioner of the Department of Fish and Game or the Commissioner's designee. Under no conditions will the state be liable for the payment of any interest charges associated with the cost of the contract. The state is not responsible for and will not pay local, state, or federal taxes.

All costs associated with the contract must be stated in U.S. currency.

Payment for agreements under $500,000 for the undisputed purchase of goods or services provided to a state agency, will be made within 30 days of the receipt of a proper billing or the delivery of the goods or services to the location(s) specified in the agreement, whichever is later. A late payment is subject to 1.5% interest per month on the unpaid balance. Interest will not be paid if there is a dispute or if there is an agreement that establishes a lower interest rate or precludes the charging of interest.

Any single contract payments of $1 million or higher must be accepted by the contractor via Electronic Funds Transfer (EFT).

SEC. 2.05 PROMPT PAYMENT FOR STATE PURCHASES

Removed

SEC. 2.06 CONTRACT ADMINISTRATION

The administration of this contract is the responsibility of the procurement officer or person appointed by the Department of Fish and Game, Division of Wildlife Conservation.

SEC. 2.07 CONTRACT PRICE ADJUSTMENTS

Removed.

SEC. 2.08 JOINT VENTURES

Joint ventures will not be allowed.

14 Revised 3/7/2024

SEC. 2.09 RIGHT TO INSPECT PLACE OF BUSINESS

At reasonable times, the state may inspect those areas of the contractor's place of business that are related to the performance of a contract. If the state makes such an inspection, the contractor must provide reasonable assistance.

SEC. 2.10 F.O.B. POINT

The F.O.B. point for all items purchased under this contract is the final destination anywhere within the State of Alaska. Ownership of and title to the ordered items remains with the contractor until the items have been delivered to their final destination and are accepted by the state.

The cost of shipping and delivery within Ketchikan, AK is to be included in the bid price. There will be no additional charge for shipping and delivery within Ketchikan, AK.

SEC. 2.11 INSPECTION & MODIFICATION - REIMBURSEMENT FOR

UNACCEPTABLE DELIVERABLES

The contractor is responsible for providing all products or the completion of all work set out in the contract. All products or work is subject to inspection, evaluation, and approval by the state. The state may employ all reasonable means to ensure that the work is progressing and being performed in compliance with the contract. The state may instruct the contractor to make corrections or modifications if needed in order to accomplish the contract’s intent.

The contractor will not unreasonably withhold such changes.

Substantial failure of the contractor to perform the contract may cause the state to terminate the contract. In this event, the state may require the contractor to reimburse monies paid (based on the identified portion of unacceptable products or work received) and may seek associated damages.

SEC. 2.12 EQUIPMENT INSPECTION

Equipment offered (including for lease) may be subject to inspection and approval by the state prior to the award of the ITB. The equipment and attachments must be in good repair and capable of performing the work for which they were designed.

SEC. 2.13 NEW EQUIPMENT

Equipment offered in response to this ITB must be new equipment. New equipment means equipment that is currently in production by the manufacturer and is still the latest model, edition or version generally offered. The equipment must be warranted as new by the manufacturer and may not have been used for any purpose, other than display (not demonstration), prior to its sale to the state. The state will not accept remanufactured, used, or reconditioned equipment. It is the contractor's responsibility to ensure that each piece of equipment delivered to the state complies with this requirement. A contractor's failure to comply with this requirement will cause the state to seek remedies under breach of contract.

SEC. 2.14 REMANUFACTURED/RECONDITIONED EQUIPMENT

Remanufactured/reconditioned is acceptable provided it meets the requirements of this clause and the requirements of the rest of this ITB. Remanufactured/reconditioned equipment is defined as used equipment that has been remanufactured/reconditioned and restored to new condition. All remanufactured/reconditioned equipment must have the same warranty as new equipment and be certified as maintainable by its manufacturer. Bidders should

15 Revised 3/7/2024 attach a copy of this certification to their bid. A bidder's failure to provide the document(s) mentioned above, within the time required by the state, will cause the state to consider the bid non-responsive and reject the bid.

SEC. 2.15 LEMON CLAUSE

This clause applies to all equipment purchased through this contract. The application period is 1-year from the date of purchase. This clause takes precedence over any other warranty or service maintenance clauses associated with this contract.

Any equipment that fails (except due to operator error) to operate according to the manufacturer's published performance specifications and/or is subject to recurring related problems must be replaced with the same make and model of new equipment at no cost to the state.

SEC. 2.16 DISCONTINUED ITEMS

In the event an item is discontinued by the manufacturer during the life of the contract, another item may be substituted, provided that the procurement officer makes a written determination that it is equal to or better than the discontinued item and provided that it is sold at the same price or less than the discontinued item.

SEC. 2.17 LIQUIDATED DAMAGES

Reserved.

SEC. 2.18 SHIPPING DAMAGE

The state will not accept or pay for damaged goods. The contractor must file all claims against the carrier(s) for damages incurred to items in transit from the point of origin to the ultimate destination. The state will provide the contractor with written notice when damaged goods are received. The state will deduct the cost of the damaged goods from the invoice prior to payment. The contractor must file all claims against the carrier(s) for reimbursement of the loss.

SEC. 2.19 CONTRACT CHANGES – UNANTICIPATED AMENDMENTS

During the course of this contract, the contractor may be required to perform additional work. That work will be within the general scope of the initial contract. When additional work is required, the state will provide the contractor a written description of the additional work and request the contractor to submit a firm time schedule for accomplishing the additional work and a firm price for the additional work. Cost and pricing data must be provided to justify the cost of such amendments per AS 36.30.400.

The contractor will not commence additional work until the procurement officer has secured required state approvals necessary and issued a written contract amendment.

16 Revised 3/7/2024

SEC. 2.20 CONTINUING OBLIGATION OF CONTRACTOR

Notwithstanding the expiration date of a contract resulting from this ITB, the contractor is obligated to fulfill its responsibilities until warranty, guarantee, maintenance, and parts availability requirements have completely expired.

SEC. 2.21 BILLING INSTRUCTIONS

All invoices produced by the contractor must contain the following information at a minimum:

1. Reference to the Contract and purchase order that will be issued after the contract has been signed.

Invoices must be billed to the ordering agency's address shown on the individual Purchase Order, Contract Award or Delivery Order. The state will make payment after it receives the goods or services and the invoice. Questions concerning payment must be addressed to the ordering agency.

SEC. 2.22 ESTIMATED QUANTITIES

No Estimated quantities are included in this ITB

SEC. 2.23 WARRANTY

The contractor warrants every unit purchased against faulty materials and workmanship for a minimum period of at least 1-year. If, during this period, faults develop with the unit or components of the unit, they will be repaired or replaced without any cost, including any transportation or freight cost, to the state. Bids, which include supplemental warranties, will be accepted, but supplemental warranties that conflict with or diminish the state's rights under this warranty clause will be considered null and void. The state is not responsible for identifying conflicting warranty conditions before issuing a contract award. After award of the contract:

1. if a conflict arises between the supplemental warranty and the warranty in this ITB, the warranty in the ITB will prevail; and

2. if the state's rights are diminished as a result of application of the supplemental warranty, the supplemental warranty will be considered null and void and the ITB warranty will prevail.

By signature on the face page of this ITB the bidder acknowledges this requirement and indicates unconditional acceptance of this warranty clause.

SEC. 2.24 NONDISCLOSURE AND CONFIDENTIALITY

Contractor agrees that all confidential information shall be used only for purposes of providing the deliverables and performing the services specified herein and shall not disseminate or allow dissemination of confidential information except as provided for in this section. The contractor shall hold as confidential and will use reasonable care (including both facility physical security and electronic security) to prevent unauthorized access by, storage, disclosure, publication, dissemination to and/or use by third parties of, the confidential information. “Reasonable care” means compliance by the contractor with all applicable federal and state law, including the Social Security Act and HIPAA. The contractor must promptly notify the state in writing if it becomes aware of any storage, disclosure, loss, unauthorized access to or use of the confidential information.

17 Revised 3/7/2024

Confidential information, as used herein, means any data, files, software, information or materials (whether prepared by the state or its agents or advisors) in oral, electronic, tangible or intangible form and however stored, compiled or memorialized that is classified confidential as defined by State of Alaska classification and categorization guidelines provided by the state to the contractor or a contractor agent or otherwise made available to the contractor or a contractor agent in connection with this contract, or acquired, obtained or learned by the contractor or a contractor agent in the performance of this contract. Examples of confidential information include, but are not limited to technology infrastructure, architecture, financial data, trade secrets, equipment specifications, user lists, passwords, research data, and technology data (infrastructure, architecture, operating systems, security tools, IP addresses, etc.).

If confidential information is requested to be disclosed by the contractor pursuant to a request received by a third party and such disclosure of the confidential information is required under applicable state or federal law, regulation, governmental or regulatory authority, the contractor may disclose the confidential information after providing the state with written notice of the requested disclosure ( to the extent such notice to the state is permitted by applicable law) and giving the state opportunity to review the request. If the contractor receives no objection from the state, it may release the confidential information within 30 days. Notice of the requested disclosure of confidential information by the contractor must be provided to the state within a reasonable time after the contractor’s receipt of notice of the requested disclosure and, upon request of the state, shall seek to obtain legal protection from the release of the confidential information.

The following information shall not be considered confidential information: information previously known to be public information when received from the other party; information freely available to the general public;

information which now is or hereafter becomes publicly known by other than a breach of confidentiality hereof; or information which is disclosed by a party pursuant to subpoena or other legal process and which as a result becomes lawfully obtainable by the general public.

SEC. 2.25 INDEMNIFICATION

The contractor shall indemnify, hold harmless, and defend the contracting agency from and against any claim of, or liability for error, omission or negligent act of the contractor under this agreement. The contractor shall not be required to indemnify the contracting agency for a claim of, or liability for, the independent negligence of the contracting agency. If there is a claim of, or liability for, the joint negligent error or omission of the contractor and the independent negligence of the contracting agency, the indemnification and hold harmless obligation shall be apportioned on a comparative fault basis.

“Contractor” and “contracting agency”, as used within this and the following article, include the employees, agents and other contractors who are directly responsible, respectively, to each. The term “independent negligence” is negligence other than in the contracting agency’s selection, administration, monitoring, or controlling of the contractor and in approving or accepting the contractor’s work.

SEC. 2.26 INSURANCE

Without limiting the contractor's indemnification, it is agreed that the contractor shall purchase at its own expense and maintain in force at all times during the performance of services under this agreement the following policies of insurance. Where specific limits are shown, it is understood that they shall be the minimum acceptable limits. If the contractor's policy contains higher limits, the state shall be entitled to coverage to the extent of such higher limits.

18 Revised 3/7/2024

Certificates of Insurance must be furnished to the procurement officer prior to contract approval and must provide for a notice of cancellation, non-renewal, or material change of conditions in accordance with policy provisions.

Failure to furnish satisfactory evidence of insurance or lapse of the policy is a material breach of this contract and shall be grounds for termination of the contractor's services. All insurance policies shall comply with and be issued by insurers licensed to transact the business of insurance under AS 21.

Proof of insurance is required for the following:

• Workers' Compensation Insurance: The contractor shall provide and maintain, for all employees engaged in work under this contract, coverage as required by AS 23.30.045, and where applicable, any other statutory obligations including but not limited to Federal U.S.L. & H. and Jones Act requirements. The policy must waive subrogation against the state.

• Commercial General Liability Insurance: covering all business premises and operations used by the contractor in the performance of services under this agreement with minimum coverage limits of $300,000 combined single limit per occurrence.

• Commercial Automobile Liability Insurance: covering all vehicles used by the contractor in the performance of services under this agreement with minimum coverage limits of $300,000 combined single limit per occurrence.

19 Revised 3/7/2024

SECTION 3. BID FORMAT AND CONTENT

SEC. 3.01 BID FORMS

Bidders shall use the front page of this ITB, the Bid Submission Cover Sheet, and any other forms identified in this ITB for submitting bids. All bids must be signed by an individual authorized to bind the bidder to the provisions of the ITB.

BIDDER'S CERTIFICATION

By signature on the bid, the bidder certifies that they comply with the following:

A. the laws of the State of Alaska;

B. the applicable portion of the Federal Civil Rights Act of 1964;

C. the Equal Employment Opportunity Act and the regulations issued thereunder by the state and federal government;

D. the Americans with Disabilities Act of 1990 and the regulations issued thereunder by the state and federal government;

E. all terms and conditions set out in this ITB;

F. the price(s) submitted was arrived at independently arrived and without collusion, under penalty of perjury;

and

G. that the bid will remain open and valid for at least 90 days.

If any bidder fails to comply with [a] through [g] of this paragraph, the state reserves the right to disregard the bid, terminate the contract, or consider the contractor in default.

CONFLICT OF INTEREST

Each bid shall include a statement indicating whether the company or any individuals working on the contract has a possible conflict of interest (e.g., currently employed by the State of Alaska or formerly employed by the State of Alaska within the past two years) and, if so, the nature of that conflict. The procurement officer reserves the right to consider a bid non-responsive and reject it or cancel the award if any interest disclosed from any source could either give the appearance of a conflict or cause speculation as to the objectivity of the contract to be performed by the bidder.

SEC. 3.02 BID BOND – PERFORMANCE BOND – SURETY DEPOSIT

Bid Bond Reserved.

Performance Bond Reserved.

Surety Deposit Reserved.

20 Revised 3/7/2024

SEC. 3.03 PRICES

The bidder shall state prices in the units of issue on this ITB. Prices quoted in bids must be exclusive of federal, state, and local taxes. If the bidder believes that certain taxes are payable by the state, the bidder may list such taxes separately, directly below the bid price for the affected item.

The Price given on the bid must include all items, labor, shipping and specifications requested in the scope of work.

21 Revised 3/7/2024

SECTION 4. EVALUATION AND CONTRACTOR

SELECTION

SEC. 4.01 EVALUATION OF BIDS

After bid opening, the procurement officer will evaluate the bids for responsiveness. Bids deemed non-responsive will be eliminated from further consideration. An evaluation may not be based on discrimination due the race, religion, color, national origin, sex, age, marital status, pregnancy, parenthood, disability, or political affiliation of the bidder.

SEC. 4.02 APPLICATION OF PREFERENCES

Certain preferences apply to all state contracts, regardless of their dollar value. The Alaska Bidder and Alaska Veteran preferences are the most common preferences involved in the ITB process. Additional preferences that may apply to this procurement are listed below. Guides that contain excerpts from the relevant statutes and codes, explain when the preferences apply and provide examples of how to calculate the preferences are available at the following website:

https://oppm.doa.alaska.gov/policy-oversight/policy-resources/user-guide-matrixes/

• Alaska Products Preference - AS 36.30.332

• Recycled Products Preference - AS 36.30.337

• Local Agriculture and Fisheries Products Preference - AS 36.15.050

• Employment Program Preference - AS 36.30.321(b)

• Alaskans with Disabilities Preference - AS 36.30.321(d)

The Division of Vocational Rehabilitation in the Department of Labor and Workforce Development keeps a list of qualified employment programs and individuals who qualify as persons with a disability. As evidence of a business’ or an individual's right to the Employment Program or Alaskans with Disabilities preferences, the Division of Vocational Rehabilitation will issue a certification letter. To take advantage of these preferences, a business or individual must be on the appropriate Division of Vocational Rehabilitation list prior to the time designated for receipt of proposals. Bidders must attach a copy of their certification letter to the proposal. A bidder’s failure to provide this certification letter with their proposal will cause the state to disallow the preference.

SEC. 4.03 ALASKA BIDDER PREFERENCE

An Alaska Bidder Preference of 5% will be applied to the total bid price. The preference will be given to a bidder who:

1) holds a current Alaska business license prior to the deadline for receipt of bids;

2) submits a bid for goods or services under the name appearing on the bidder’s current Alaska business license;

3) has maintained a place of business within the state staffed by the bidder, or an employee of the bidder, for a period of six months immediately preceding the date of the bid;

https://oppm.doa.alaska.gov/policy-oversight/policy-resources/user-guide-matrixes/

22 Revised 3/7/2024

4) is incorporated or qualified to do business under the laws of the state, is a sole proprietorship and the proprietor is a resident of the state, is a limited liability company (LLC) organized under AS 10.50 and all members are residents of the state, or is a partnership under AS 32.06 or AS 32.11 and all partners are residents of the state; and

5) if a joint venture, is composed entirely of ventures that qualify under (1)-(4) of this subsection.

Alaska Bidder Preference Certification Form To receive the Alaska Bidder Preference, the bid must include the Alaska Bidder Preference Certification Form attached to this ITB. A bidder does not need to complete the Alaska Veteran Preference questions on the form if not claiming the Alaska Veteran Preference. A bidder’s failure to provide this completed form with their bid will cause the state to disallow the preference.

SEC. 4.04 ALASKA VETERAN PREFERENCE

An Alaska Veteran Preference of 5%, not to exceed $5,000, will be applied to the total bid price. The preference will be given to a bidder who qualifies under AS 36.30.990(2) as an Alaska Bidder and is a:

a) sole proprietorship owned by an Alaska veteran;

b) partnership under AS 32.06 or AS 32.11 if a majority of the partners are Alaska veterans;

c) limited liability company organized under AS 10.50 if a majority of the members are Alaska veterans; or

d) corporation that is wholly owned by individuals, and a majority of the individuals are Alaska veterans.

In accordance with AS 36.30.321(i), the bidder must also add value by actually performing, controlling, managing, and supervising the services provided, or for supplies, the bidder must have sold supplies of the general nature solicited to other state agencies, other government, or the general public.

Alaska Veteran Preference Certification To receive the Alaska Veteran Preference, the bid must include the Alaska Bidder Preference Certification Form attached to this ITB. A bidder’s failure to provide this completed form with their bid will cause the state to disallow the preference.

SEC. 4.05 USE OF LOCAL FOREST PRODUCTS

In a project financed by state money in which the use of timber, lumber and manufactured lumber is required, only timber, lumber and…