HYDRAULIC PRESS BRAKE.docx

HYDRAULIC PRESS BRAKE

SPECIFICATIONS

The intent of this specification is to describe a 350 ton hydraulic press brake that will be used in the fabrication department of MDOT Fleet Services. The press brake must be designed and manufactured for heavy duty service and have the capability to maintain very close tolerances for repeatable performance standards. The unit must be of current manufacture and production and must have all standard items as offered in brochures by the manufacturer along with all specifications within. The following requirements and criteria for this unit shall be met completely. Press must meet all ANSI, NFPA and any other applicable standards / regulations for its intended use.

The award will be made on a best value basis to the vendor that either meets or most closely meets the specifications, while taking price and delivery into consideration.

Please complete all checklists. An X will have the same meaning as standard or specified equipment. Make note of all exceptions and identify as not available or dealer installed.

The following abbreviations must be used:

Item #1 Dimensions:

1.1 Overall height 120 inches (maximum).

1.2 Overall width 57 inches (maximum).

1.3 Overall length 159 inches (maximum).

1.4 Weight 38,000 lbs (maximum).

Item # 2 Features:

2.1 Shall have four (4) 24 inch slide type support arms.

2.2 One shot lube system.

2.3 Variable tonnage control system.

2.4 Keylock switch.

2.5 Work light.

2.6 Front fence light curtain.

2.9 Shall have a sixteen (16) inch open height.

Item # 3 Tools:

3.1 Shall include a four (4) way die with Vee’s of 1”, 2”, 3”and 4” X 12 ft. long.

3.2 Shall include a die holder to accommodate the four (4) way die.

3.3 Shall include G9-12 Gooseneck Punch with safety tang, overall length of 12 ft.

3.4 Shall include segments of 1”, 1”, 1-1/2”, 2”, 3”, 4”, 6”, 6”, 12”, 24”, 36” & 48”

3.5 Shall include a U-5 punch 12 ft long with safety tang.

3.6 Shall include segments of 1”, 1”, 1-1/2”, 2”, 3 “, 4”, 6”, 6”,12”, 24”, 36” & 48”.

Item # 4 Power Requirements:

4.1 Press shall be wired for a 460 Volt 3 ph. 60 hertz power source.

Item # 5 Safety:

5.1 Must comply with any and all OSHA standards and requirements.

5.2 Must have all warning, pinch points, instructional and informational decals that apply.

Warranty:

One year parts and labor, or standard manufactures warranty shall apply whichever is greater. Warranty shall begin on the date unit is actually put into service.

General:

1. Bidders shall supply a detailed specification sheet with their bid proposals listing exactly what is being offered (not a reference to a web site).

2. These specifications are a minimum and bids will be evaluated based on price, warranty, manufacturers performance data, delivery schedule (delivery schedule may effect the award), parts availability and other items deemed appropriate.

3. Vendor shall supply two (2) each of these manuals: Owner, Parts and Operator (one set may be a CD).

4. Vendor to provide training at a later date, but within eight (8) weeks of delivery (unless other arrangements are necessary).

5. Maine DOT reserves the right to pre-inspect the equipment before delivery.

6. All bid pricing will include shipping, delivery and set-up.

7. Delivery, set-up and training will be at:

Maine DOT Fleet Service, 105 Capitol St. Augusta, Maine, 04330.

8. Upon delivery all necessary paper work such as billing invoices and manuals shall accompany the unit.

** Exceptions and Questions: All exceptions must be asked during the bid period by submitting your requests and / or questions through the Question and Answer link on the Solicitation Details View page. Your answer will appear there as well. It is the vendor’s responsibility to log in to view all questions and answers posted there. Questions and answers obtained any other way will not be valid for this RFQ.

ESB 8/12