HT940623Q0126 RFQ EXTENDED DATES.docx

HT940623Q0126

Section A - Solicitation/Contract Form

SECTION A

VENDOR TO COMPLETE THE FOLLOWING:

POINTS FO CONTACT

Naval Medical Center Portsmouth Points of Contact:

Name: LUIS ZENO Phone: 757-953- 6084 E-Mail: luis.a.zeno-pimentel.civ@health.mil

REQUEST FOR QUOTE INFORMATION & EVALUATUION FACTORS

Vendor to reference Request for Quotation (RFQ) Number HT940623Q0126 on all correspondence relating to this RFQ

The government will make an award based on an “All or None” evaluation and/or based on the “Best Value” proposed for this requirement in terms of technical capabilities, price and warranty. Vendors must provide all of the below to be considered a “responsive vendor”. The solicitation and contract award is in accordance with FAR 52.211-6 Brand Name or Equal.

Quote Evaluation factors for Best Value will be rated as follows (in order of importance):

Technical capabilities

Price evaluation Vendor to provide a published price list (not a GSA contract price list) and two invoices for the same or similar services or supplies.

Warranty

**Note to vendors for FAR 52.211-6 Brand Name of Equal: Salient Characteristics of the item can be found in Section B of this document.

PAYMENT INFORMATION

Payment in Arrears (Check One): Monthly Quarterly Semi-Annually Annually *Please ensure that quoted price matches the choice above

Note: Vendor will be required to provide billing electronically via the WAWF Electronic Invoicing Method per Section G of this RFQ. For additional information, a review of the following web sites may be required: Websites: https://wawf.eb.mil http://wawftraining Email: usn.detrick.navmedlogcomftdmd.list.nmlc-wawf@mail.mil

PROMPT PAYMENT: For Prompt Payment Act purposes, this contract is:

Subject to the 7-calendar day constructive acceptance period. This contract is subject to the Availability of funds clause 52.232-18 listed in full text in the Clause section of this contract.

AVAILABILITY OF FUNDS. Pursuant to Section I, Availability of Funds (FAR 52.232-18), of the contract, funds are not presently available for this contract. The Government’s obligation under this contract is contingent upon the availability of appropriated funds from which payment for contract purposes can be made. No legal liability on the part of the Government for any payment may arise until funds are made available to the Contracting Officer for this contract and until the Contractor receives notice of such availability, to be confirmed in writing to the Contracting Officer.

Section B - Supplies or Services and Prices

FY24 FUME HOODS CERTIFICATION

FFP

Mobile Isolation Chamber (MIC), 6 Hoods 6 hoods X 2 certifications per year = 12 quantity Manufacturer: Containment Technologies Group Inc Nomenclature: Barrier Isolators Model, S/N, ECN as follows: (1)MIC Single, 0805-MPA-363, 063436, (2)MIC Single, 0805-MPA-364, 063437 (3)MIC Dual, 1206-MPD-568, 069956 (4)MIC Dual, 1106-MPD-558, 069957

3 hoods X 2 certifications per year = 6 quantity Manufacturer: Baker CO Inc Nomenclature: Laminar Flow Work Stations Model, S/N, ECN as follows:

(1)EG-4252, 98676, 104089

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

FOB: Destination

PURCHASE REQUEST NUMBER: 0011911862

J065

NET AMT

FFP

Mobile Isolation Chamber (MIC), 6 Hoods 6 hoods X 2 certifications per year = 12 quantity Manufacturer: Containment Technologies Group Inc Nomenclature: Barrier Isolators Model, S/N, ECN as follows: (1)MIC Single, 0805-MPA-363, 063436, (2)MIC Single, 0805-MPA-364, 063437 (3)MIC Dual, 1206-MPD-568, 069956 (4)MIC Dual, 1106-MPD-558, 069957

3 hoods X 2 certifications per year = 6 quantity Manufacturer: Baker CO Inc Nomenclature: Laminar Flow Work Stations Model, S/N, ECN as follows:

(1)EG-4252, 98676, 104089

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

FOB: Destination

NET AMT

FFP

Mobile Isolation Chamber (MIC), 6 Hoods 6 hoods X 2 certifications per year = 12 quantity Manufacturer: Containment Technologies Group Inc Nomenclature: Barrier Isolators Model, S/N, ECN as follows: (1)MIC Single, 0805-MPA-363, 063436, (2)MIC Single, 0805-MPA-364, 063437 (3)MIC Dual, 1206-MPD-568, 069956 (4)MIC Dual, 1106-MPD-558, 069957

3 hoods X 2 certifications per year = 6 quantity Manufacturer: Baker CO Inc Nomenclature: Laminar Flow Work Stations Model, S/N, ECN as follows:

(1)EG-4252, 98676, 104089

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

NET AMT

FFP

Mobile Isolation Chamber (MIC), 6 Hoods 6 hoods X 2 certifications per year = 12 quantity Manufacturer: Containment Technologies Group Inc Nomenclature: Barrier Isolators Model, S/N, ECN as follows: (1)MIC Single, 0805-MPA-363, 063436, (2)MIC Single, 0805-MPA-364, 063437 (3)MIC Dual, 1206-MPD-568, 069956 (4)MIC Dual, 1106-MPD-558, 069957

3 hoods X 2 certifications per year = 6 quantity Manufacturer: Baker CO Inc Nomenclature: Laminar Flow Work Stations Model, S/N, ECN as follows:

(1)EG-4252, 98676, 104089

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

NET AMT

FFP

Mobile Isolation Chamber (MIC), 6 Hoods 6 hoods X 2 certifications per year = 12 quantity Manufacturer: Containment Technologies Group Inc Nomenclature: Barrier Isolators Model, S/N, ECN as follows: (1)MIC Single, 0805-MPA-363, 063436, (2)MIC Single, 0805-MPA-364, 063437 (3)MIC Dual, 1206-MPD-568, 069956 (4)MIC Dual, 1106-MPD-558, 069957

3 hoods X 2 certifications per year = 6 quantity Manufacturer: Baker CO Inc Nomenclature: Laminar Flow Work Stations Model, S/N, ECN as follows:

(1)EG-4252, 98676, 104089

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

NET AMT

Section C - Descriptions and Specifications

PWS

Department of Defense Defense Health Agency Performance Work Statement

Maintenance Services for Biomed Department

[20230207]

Naval Medical Readiness and Training Command, Portsmouth

1.0 GENERAL INFORMATION

SCOPE OF WORK

1.1 GENERAL: This is a non-personal services contract to provide certification contract support immediately upon award of a resulting order. The Government shall not exercise any supervision or control over the contract service providers performing the services herein. Such contract service providers shall be accountable solely to the Contractor who, in turn is responsible to the Government.

1.1.1 Description of Services/Introduction: The contractor shall provide all personnel, equipment, supplies, facilities, transportation, tools, materials, supervision, and other items and non-personal services necessary to provide calibration support for the items listed in Section B and all support items / components as defined in this PWS except for those items specified as government furnished property and services. The contractor shall perform to the standards in this contract.

1.1.2 Background: The Contractor shall be qualified / authorized by the OEM (IE: Certified Agent of the OEM) in the repair of all equipment listed within this contract. Certification of the OEM must be current (within 2 years) at all times prior to contract award and throughout contract period. Contractor and its employees shall maintain qualifications throughout entire contract period. In the event that a sub-contractor is used for this requirement, the sub-contractor must be a Certified Agent of the OEM. Qualification includes but not limited to the certification of all repair persons and repair facilities by the OEM as being trained / qualified to perform required repairs. The Government shall maintain the right to seek proof of qualification prior to award and anytime during contract period of performance. Additionally contractor must have ready access to parts inventory of OEM replacement parts.

1.1.3 Objectives: Equipment listed in this contract will be certified to meet the original equipment manufacturer’s (OEM) specifications.

1.1.4 Period of Performance: The period of performance shall be for one (1) base year plus four (4) option years.

BASE YEAR (01-OCT-2023 to 30-SEP-2024)

OPTION YEAR 1 (01-OCT-2024 to 30-SEP-2025)

OPTION YEAR 2 (01-OCT-2025 to 30-SEP-2026)

OPTION YEAR 3 (01-OCT-2026 to 30-SEP-2027)

OPTION YEAR 4 (01-OCT-2027 to 30-SEP-2028)

GENERAL INFORMATION

1.2 Quality Control (If applicable): The contractor shall develop and maintain an effective QCP to ensure services are performed in accordance with this PWS. The contractor shall develop and implement procedures to identify, prevent, and ensure non-recurrence of defective services. The contractor’s quality control program is the means by which the contractor assures that the work performance complies with the contract requirements of the contract. [The QCP is to be delivered, within 30 days after contract award or with the contractor’s proposal if it is an evaluation factor, three copies of a comprehensive written QCP shall be submitted to the Contracting Officer (KO) and Contracting Officer Representative (COR) within 5 working days when changes are made thereafter.] After acceptance of the QSP the contractor shall receive the KO’s acceptance in writing of any proposed change to the QC system.

1.3 Quality Assurance: The government shall evaluate the contractor’s performance under this contract in accordance with the Quality Assurance Surveillance Plan (QASP). This plan is primarily focused on what the Government must do to ensure that the contractor has performed in accordance with the performance standards. It defines how the performance standards will be applied, the frequency of surveillance, and the minimum acceptable defect rate(s).

1.4 Place of Performance: The work to be performed under this contract will be at a government facility.

1.5 Recognized Holidays:

1.6 Hours of Operation: The contractor is responsible for conducting business, between the hours of 8:00 A.M. to 4:30 P.M., Monday thru Friday except Federal holidays or when the Government facility is closed due to local or national emergencies, administrative closings, or similar Government directed facility closings. The Contractor must at all times maintain an adequate workforce for the uninterrupted performance of all tasks defined within this PWS when the Government facility is not closed for the above reasons. When hiring personnel, the Contractor shall keep in mind that the stability and continuity of the workforce are essential.

1.7 Type of Contract: The government will award a FFP Contract.

1.8 PHYSICAL Security: The contractor shall be responsible for safeguarding all government equipment, information and property provided for contractor use. At the close of each work period, government facilities, equipment, and materials shall be secured.

1.8.1 Key Control (If applicable). The Contractor shall establish and implement methods of making sure all keys/key cards issued to the Contractor by the Government are not lost or misplaced and are not used by unauthorized persons. NOTE: All references to keys include key cards. No keys issued to the Contractor by the Government shall be duplicated. The Contractor shall develop procedures covering key control that shall be included in the QCP. Such procedures shall include turn-in of any issued keys by personnel who no longer require access to locked areas. The Contractor shall immediately report any occurrences of lost or duplicate keys/key cards to the KO.

1.8.2 In the event keys, other than master keys, are lost or duplicated, the Contractor shall, upon direction of the Contracting Officer, re-key or replace the affected lock or locks; however, the Government, at its option, may replace the affected lock or locks or perform re-keying. When the replacement of locks or re-keying is performed by the Government, the total cost of re-keying or the replacement of the lock or locks shall be deducted from the monthly payment due the Contractor. In the event a master key is lost or duplicated, all locks and keys for that system shall be replaced by the Government and the total cost deducted from the monthly payment due the Contractor.

1.8.3 The Contractor shall prohibit the use of Government issued keys/key cards by any persons other than the Contractor’s employees. The Contractor shall prohibit the opening of locked areas by Contractor employees to permit entrance of persons other than Contractor employees engaged in the performance of assigned work in those areas, or personnel authorized entrance by the Contracting Officer.

1.8.3.1 Lock Combinations (If applicable). The Contractor shall establish and implement methods of ensuring that all lock combinations are not revealed to unauthorized persons. The Contractor shall ensure that lock combinations are changed when personnel having access to the combinations no longer have a need to know such combinations. These procedures shall be included in the Contractor’s QCP

1.9 Special Qualifications: The contractor is responsible for ensuring all employees possess and maintain current Information Assurance Technician (IAT) Level I professional certification during the execution of this contract.

1.9.1 The Contractor shall provide trained, experienced, English speaking personnel, labor, tools, diagnostic equipment, software, test phantoms, material, supplies, transportation, parts and equipment necessary to perform Preventive Maintenance (PM), Calibration (CAL), Safety testing (ST) and corrective maintenance.

1.9.2 The Contractor shall provide telephonic communications with the Government to discuss technical matters relating to the performance of this contract. A systems operator will be made available to answer technical questions regarding system operations and applications.

1.10 Contracting Officer Representative (COR): The COR will be identified by COR Appointment letter. The COR monitors all technical aspects of the contract and assists in contract administration. The COR is authorized to perform the following functions: assure that the Contractor performs the technical requirements of the contract: perform inspections necessary in connection with contract performance: maintain written and oral communications with the Contractor concerning technical aspects of the contract: issue written interpretations of technical requirements; including Government drawings; designs; specifications; monitor Contractor's performance and notify both the KO and Contractor of any deficiencies; coordinate availability of government furnished property, and provide site entry of Contractor personnel. A letter of designation issued to the COR, a copy of which is sent to the Contractor, states the responsibilities and limitations of the COR, especially with regard to changes in cost or price, estimates or changes in delivery dates. The COR is not authorized to change any of the terms and conditions of the contract

1.11 Identification of Contractor Employees: All contract personnel attending meetings, answering Government telephones, and working in other situations where their contractor status is not obvious to third parties are required to identify themselves as such to avoid creating an impression in the minds of members of the public that they are Government officials. They must also ensure that all documents or reports produced by contractors are suitably marked as contractor products or that contractor participation is appropriately disclosed.

1.11.2 Contractors shall wear identifying badges at all times when conducting business inside a government facility.

1.11.3 To obtain a gate pass, refer to http://dbids.dmdc.mil/#!/register

1.12 Contractor Travel (If applicable): [Insert any travel requirements.]. For example: Contractor will be required to travel CONUS during the performance of this contract to attend meetings, conferences, and training. The contractor may be required to travel to off-site training locations and to ship training aids to these locations in support of this PWS. Required language should travel be needed: Contractor will be authorized travel expenses consistent with the substantive provisions of the Joint Travel Regulation (JTR) and the limitation of funds specified in this contract. All travel requires Government approval/authorization and notification to the COR. For proposal purposes, a Not to exceed amount for travel can be established or you can include in your IGE and the workload summary , a projected listing of travel locations to include frequency and number of persons required to travel so the offerors can provide pricing.

1.13 Other Direct Costs (If applicable): [Insert what the other direct costs requirements will be. These costs must be preapproved by the KO] For example: This category includes travel, reproduction, and shipping expenses associated with training activities and visits to contractor facilities.

1.14 Data Rights (If applicable): The Government has unlimited rights to all documents/material produced under this contract. All documents and materials, to include the source codes of any software, produced under this contract shall be Government owned and are the property of the Government with all rights and privileges of ownership/copyright belonging exclusively to the Government. These documents and materials may not be used or sold by the contractor without written permission from the KO. All materials supplied to the Government shall be the sole property of the Government and may not be used for any other purpose. This right does not abrogate any other Government rights.

1.15 Organizational Conflict of Interest (If applicable): It is the contractor’s responsibility to notify the KO of any potential Organizational Conflict of Interest (OCI). In the event that an OCI exist the contractor shall propose a Mitigation plan that shall be reviewed and accepted by the KO prior to continuance of the work that presents an OCI. Should the proposed Mitigation Plan is not accepted by the KO, the Government may terminate this contract, disqualify the Contractor from subsequent contractual efforts, and pursue any remedies as may be permitted by the law or this contract.

PART 2

DEFINITIONS & ACRONYMS

DEFINITIONS AND ACRONYMS:

DEFINITIONS

CONTRACTOR. A supplier or vendor awarded a contract to provide specific supplies or service to the government. The term used in this contract refers to the prime.

CONTRACTING OFFICER (KO). A person with authority to enter into, administer, and/or terminate contracts, and make related determinations and findings on behalf of the government. This is the only individual who can legally bind the government.

CONTRACTING OFFICER'S REPRESENTATIVE (COR). An employee of the U.S. Government appointed by the contracting officer to administer the contract. Such appointment shall be in writing and shall state the scope of authority and limitations. This individual has authority to provide technical direction to the Contractor as long as that direction is within the scope of the contract, does not constitute a change, and has no funding implications. This individual does NOT have authority to change the terms and conditions of the contract.

DEFECTIVE SERVICE. A service output that does not meet the standard of performance associated with the Performance Work Statement.

DELIVERABLE. Anything that can be physically delivered, but may include non-manufactured things such as meeting minutes or reports.

KEY PERSONNEL. Contractor personnel that are evaluated in a source selection process and that may be required to be used in the performance of a contract by the Key Personnel listed in the PWS. When key personnel are used as an evaluation factor in best value procurement, an offer can be rejected if it does not have a firm commitment from the persons that are listed in the proposal.

PHYSICAL SECURITY. Actions that prevent the loss or damage of Government property.

QUALITY ASSURANCE. The government procedures to verify that services being performed by the Contractor are performed according to acceptable standards.

QUALITY ASSURANCE SURVEILLANCE PLAN (QASP). An organized written document specifying the surveillance methodology to be used for surveillance of contractor performance.

QUALITY CONTROL. All necessary measures taken by the Contractor to assure that the quality of an end product or service meet contract requirements.

SUBCONTRACTOR. One that enters into a contract with a prime contractor. The Government does not have privity of contract with the subcontractor.

WORK DAY. The number of hours per day the Contractor provides services in accordance with the contract.

WORK WEEK. Monday through Friday, unless specified otherwise.

ACRONYMS:

PART 3

GOVERNMENT FURNISHED PROPERTY, EQUIPMENT, AND SERVICES

GOVERNMENT FURNISHED ITEMS AND SERVICES:

The government will be responsible for maintaining the proper environment, including utilities and site requirements necessary for the system to function properly as specified by the OEM.

The Government will operate the system in accordance with the instruction manual provided by the OEM.

PART 4.0

4 CONTRACTOR FURNISHED ITEMS AND SPECIFIC TASKS

4.1 Government furnished property, Materials and Services.

The government certifies that the equipment to be maintained under this contract will be in good operating condition on the effective date of this contract. For the purpose of this contract, the clause, “good operating condition” means the conditions necessary for the equipment to function as intended without corrective maintenance. The Contractor agrees to leave the equipment in good operating condition at the expiration of this contract. During the final week of this contract, the Government will make final inspection of the equipment. Any correction of deficiencies noted during this inspection shall be resolved prior to contract end. The Government reserves the right to request the repair (at no additional cost to the Government) of items identified with latten defects after contract termination, when it has been determined that defects either are a result of contractor’s performance or should have been discovered during normal performance of work under this contract.

4.1.2 The Government will not be responsible for the damage or loss due to fire, theft, accident, or other disaster of Contractor supplies, materials, or for the personal belongings brought onto Government property by Contractor’s personnel.

4.2 Contractor Furnished Property and Material.

The Contractor shall provide all service literature, reference publications, laptop computers and diagnostic software to be used by the contractor service technicians and as required for the completion of the services in accordance with this contract.

4.3 Contractor Report Requirements.

During normal duty hours, Contracted Field Service Engineer (FSE) personnel shall check-in with the Biomedical Engineering Division upon arrival at the Government site and again prior to departure. (Biomedical Engineering located in Build-250 1st floor; 757-953-5336). The Contractor FSEs shall personally notify Biomedical Engineering (BME) of problems that result in the equipment being left disabled upon their departure. After normal duty hours, Contractor FSE’s shall notify the Officer of the Day Desk (Bldg 2, 2nd Floor) and the systems operator designated by BME.

4.3.1 The Contractor shall provide to BME a full service report within two (2) days after completion of all service performed. Additionally contractor will be required to affix a tag on equipment upon the completion of a calibration. Tag may either be a “sticker” or “hanging tag”. As a minimum the tag shall contain: the name of the contractor, technician performing inspection and date of inspection legibly printed.

4.4 Contractor Responsibility.

4.4.1 The Contractor shall be responsible for the repair/replacement of damaged Government owned equipment and property due to the negligence of the Contractor or his representatives. All such replacement or repair shall be at the Contractor’s expense and shall be inspected to the satisfaction of the KO or appointed representative.

4.4.2 All test equipment used in the performance of this contract must be calibrated (if required / as required by manufacture of test equipment) and shall be in compliance with Joint Commission on Accreditation of Healthcare Organizations (JCAHO), Original Equipment Manufacturer (OEM) and Federal Drug Administration (FDA) standards as required.

PART 5

APPLICABLE PUBLICATIONS

(In this section list any publications, manuals, and/or regulations that the contractor must abide by. See example provided below.)

5 APPLICABLE PUBLICATIONS (CURRENT EDITIONS) (If applicable): (In this section list any publications, manuals, and/or regulations that the contractor must abide by. See example provided below.)

5.4 The Contractor must abide by all applicable regulations, publications, manuals, and local policies and procedures. (For example, FAR Part 10, AR 25-2, AR 530-1.)

PART 6

ATTACHMENT/TECHNICAL EXHIBIT LISTING

(Under this section list all attachments and technical exhibits that will be useful for the contractor to submit an appropriate proposal.)

6 Attachment List:

6.4 Attachment 1– Quality Assurance Surveillance Plan (QASP)(This document is required for every PWS. See attached example for format.)

6.5 Attachment 2– Deliverables Schedule (This document is required for every PWS. See attached example for format.

Section E - Inspection and Acceptance

INSPECTION AND ACCEPTANCE TERMS

Supplies/services will be inspected/accepted at:

CLAUSES INCORPORATED BY REFERENCE

Section F - Deliveries or Performance

NMCP HOURS OF DELIVERY

Naval Medical Center Portsmouth (NMCP) Receiving Dock Hours of Operation:

NMCP Receiving Dock is open Monday through Friday 0700 to 1600 (7:00 a.m. to 4:00 p.m.), excluding federal holidays. Receiving personnel may be reached at 757-953-5770.

DELIVERY INFORMATION

DFAS INDIANAPOLIS (GFEBS) 21001

8899 E. 56 TH STREET

INDIANAPOLIS IN 46249-3120

INDIANAPOLIS IN 46249-3120

HT0242

HT0242

HT0242

HT0242

HT0242

Section G - Contract Administration Data

CLAUSES INCORPORATED BY FULL TEXT

252.232-7006 WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (DEC 2018)

(a) Definitions. As used in this clause—

“Department of Defense Activity Address Code (DoDAAC)” is a six position code that uniquely identifies a unit, activity, or organization.

“Document type” means the type of payment request or receiving report available for creation in Wide Area WorkFlow (WAWF).

“Local processing office (LPO)” is the office responsible for payment certification when payment certification is done external to the entitlement system.

“Payment request” and “receiving report” are defined in the clause at 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports.

(b) Electronic invoicing. The WAWF system provides the method to electronically process vendor payment requests and receiving reports, as authorized by Defense Federal Acquisition Regulation Supplement (DFARS) 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports.

(c) WAWF access. To access WAWF, the Contractor shall—

(1) Have a designated electronic business point of contact in the System for Award Management at https://www.sam.gov; and

(2) Be registered to use WAWF at https://wawf.eb.mil/ following the step-by-step procedures for self-registration available at this web site.

(d) WAWF training. The Contractor should follow the training instructions of the WAWF Web-Based Training Course and use the Practice Training Site before submitting payment requests through WAWF. Both can be accessed by selecting the “Web Based Training” link on the WAWF home page at https://wawf.eb.mil/.

(e) WAWF methods of document submission. Document submissions may be via web entry, Electronic Data Interchange, or File Transfer Protocol.

(f) WAWF payment instructions. The Contractor shall use the following information when submitting payment requests and receiving reports in WAWF for this contract or task or delivery order:

(1) Document type. The Contractor shall submit payment requests using the following document type(s):

(i) For cost-type line items, including labor-hour or time-and-materials, submit a cost voucher.

(ii) For fixed price line items—

(A) That require shipment of a deliverable, submit the invoice and receiving report specified by the Contracting Officer.

(B) For services that do not require shipment of a deliverable, submit either the Invoice 2in1, which meets the requirements for the invoice and receiving report, or the applicable invoice and receiving report, as specified by the Contracting Officer.

____________Invoice_2 in 1 Service ______________________________________________

(iii) For customary progress payments based on costs incurred, submit a progress payment request.

(iv) For performance based payments, submit a performance based payment request.

(v) For commercial item financing, submit a commercial item financing request.

(2) Fast Pay requests are only permitted when Federal Acquisition Regulation (FAR) 52.213-1 is included in the contract.

(3) Document routing. The Contractor shall use the information in the Routing Data Table below only to fill in applicable fields in WAWF when creating payment requests and receiving reports in the system.

Routing Data Table*

(4) Payment request. The Contractor shall ensure a payment request includes documentation appropriate to the type of payment request in accordance with the payment clause, contract financing clause, or Federal Acquisition Regulation 52.216-7, Allowable Cost and Payment, as applicable.

(5) Receiving report. The Contractor shall ensure a receiving report meets the requirements of DFARS Appendix F.

(g) WAWF point of contact. edward.r.gollon.civ@mail.mil ; charles.k.lovell2.civ@mail.mil

(1) The Contractor may obtain clarification regarding invoicing in WAWF from the following contracting activity’s WAWF point of contact.

usn.detrick.navmedlogcomftdmd.list.nmlc-wawf@mail.mil

(2) Contact the WAWF helpdesk at 866-618-5988, if assistance is needed.

(End of clause)

Section H - Special Contract Requirements

PRIVACY AND SECURITY

PRIVACY AND SECURITY OF PROTECTED HEALTH INFORMATION

1. Introduction

In accordance with DoD 6025.18-R “Department of Defense Health Information Privacy Regulation,” January 24, 2003, the Contractor meets the definition of Business Associate. Therefore, a Business Associate Agreement is required to comply with both the Health Insurance Portability and Accountability Act (HIPAA) Privacy and Security regulations. This clause serves as that agreement whereby the Business Associate agrees to abide by all applicable HIPAA Privacy and Security requirements regarding health information as defined in this clause, and in DoD 6025.18-R and DoD 8580.02, as amended. Additional requirements will be addressed when implemented.

a. Definitions. As used in this clause generally refer to the Code of Federal Regulations (CFR) definition unless a more specific provision exists in DoD 6025.18-R or DoD 8580.02.

(1) HITECH Act shall mean the Health Information Technology for Economic and Clinical Health Act included in the American Recovery and Reinvestment Act of 2009.

(2) Individual has the same meaning as the term “individual” in 45 CFR 160.103 and shall include a person who qualifies as a personal representative in accordance with 45 CFR 164.502(g).

(3) Privacy Rule means the Standards for Privacy of Individually Identifiable Health Information at 45 CFR part 160 and part 164, subparts A and E.

(4) Protected Health Information has the same meaning as the term “protected health information” in 45 CFR 160.103, limited to the information created or received by the Business Associate from or on behalf of the Government pursuant to the Contract.

(5) Electronic Protected Health Information has the same meaning as the term “electronic protected health information” in 45 CFR 160.103.

(6) Required by Law has the same meaning as the term “required by law” in 45 CFR 164.103.

(7) Secretary means the Secretary of the Department of Health and Human Services or his/her designee.

(8) Security Incident will have the same meaning as the term “security incident” in 45 CFR 164.304, limited to the information created or received by Business Associate from or on behalf of Covered Entity.

(9) Security Rule means the Health Insurance Reform: Security Standards at 45 CFR part 160, 162 and part 164, subpart C.

(10) Terms used, but not otherwise defined, in this Clause shall have the same meaning as those terms in 45 CFR 160.103, 160.502, 164.103, 164.304, and 164.501.

b. The Business Associate shall not use or further disclose Protected Health Information other than as permitted or required by the Contract or as Required by Law.

c. The Business Associate shall use appropriate safeguards to maintain the privacy of the Protected Health Information and to prevent use or disclosure of the Protected Health Information other than as provided for by this Contract.

d. The HIPAA Security administrative, physical, and technical safeguards in 45 CFR 164.308, 164.310, and 164.312, and the requirements for policies and procedures and documentation in 45 CFR 164.316 shall apply to Business Associate. The additional requirements of Title XIII of the HITECH Act that relate to the security and that are made applicable with respect to covered entities shall also be applicable to Business Associate. The Business Associate agrees to use administrative, physical, and technical safeguards that reasonably and appropriately protect the confidentiality, integrity, and availability of the electronic protected health information that it creates, receives, maintains, or transmits in the execution of this Contract.

e. The Business Associate shall, at their own expense, take action to mitigate, to the extent practicable, any harmful effect that is known to the Business Associate of a use or disclosure of Protected Health Information by the Business Associate in violation of the requirements of this Clause. These mitigation actions will include as a minimum those listed in the TMA Breach Notification Standard Operating Procedure (SOP), which is available at: http://www.tricare.mil/tmaprivacy/breach.cfm

f. The Business Associate shall report to the Government any security incident involving protected health information of which it becomes aware.

g. The Business Associate shall report to the Government any use or disclosure of the Protected Health Information not provided for by this Contract of which the Business Associate becomes aware.

h. The Business Associate shall ensure that any agent, including a sub Business Associate, to whom it provides Protected Health Information received from, or created or received by the Business Associate, on behalf of the Government, agrees to the same restrictions and conditions that apply through this Contract to the Business Associate with respect to such information.

i. The Business Associate shall ensure that any agent, including a subBusiness Associate, to whom it provides electronic Protected Health Information, agrees to implement reasonable and appropriate safeguards to protect it.

j. The Business Associate shall provide access, at the request of the Government, and in the time and manner reasonably designated by the Government to Protected Health Information in a Designated Record Set, to the Government or, as directed by the Government, to an Individual in order to meet the requirements under 45 CFR 164.524.

k. The Business Associate shall make any amendment(s) to Protected Health Information in a Designated Record Set that the Government directs or agrees to pursuant to 45 CFR 164.526 at the request of the Government, and in the time and manner reasonably designated by the Government.

l. The Business Associate shall make internal practices, books, and records relating to the use and disclosure of Protected Health Information received from, or created or received by the Business Associate, on behalf of the Government, available to the Government, or at the request of the Government to the Secretary, in a time and manner reasonably designated by the Government or the Secretary, for purposes of the Secretary determining the Government’s compliance with the Privacy Rule.

m. The Business Associate shall document such disclosures of Protected Health Information and information related to such disclosures as would be required for the Government to respond to a request by an Individual for an accounting of disclosures of Protected Health Information in accordance with 45 CFR 164.528.

n. The Business Associate shall provide to the Government or an Individual, in time and manner reasonably designated by the Government, information collected in accordance with this Clause of the Contract, to permit the Government to respond to a request by an Individual for an accounting of disclosures of Protected Health Information in accordance with 45 CFR 164.528.

2. General Use and Disclosure Provisions

Except as otherwise limited in this Clause, the Business Associate may use or disclose Protected Health Information on behalf of, or to provide services to, the Government for treatment, payment, or healthcare operations purposes, in accordance with the specific use and disclosure provisions below, if such use or disclosure of Protected Health Information would not violate the HIPAA Privacy Rule, the HIPAA Security Rule, DoD 6025.18-R or DoD 8580.02 if done by the Government. The additional requirements of Title XIII of the HITECH Act that relate to privacy and that are made applicable with respect to covered entities shall also be applicable to Business Associate.

3. Specific Use and Disclosure Provisions

a. Except as otherwise limited in this Clause, the Business Associate may use Protected Health Information for the proper management and administration of the Business Associate or to carry out the legal responsibilities of the Business Associate.

b. Except as otherwise limited in this Clause, the Business Associate may disclose Protected Health Information for the proper management and administration of the Business Associate, provided that disclosures are required by law, or the Business Associate obtains reasonable assurances from the person to whom the information is disclosed that it will remain confidential and used or further disclosed only as required by law or for the purpose for which it was disclosed to the person, and the person notifies the Business Associate of any instances of which it is aware in which the confidentiality of the information has been breached.

c. Except as otherwise limited in this Clause, the Business Associate may use Protected Health Information to provide Data Aggregation services to the Government as permitted by 45 CFR 164.504(e)(2)(i)(B).

d. Business Associate may use Protected Health Information to report violations of law to appropriate Federal and State authorities, consistent with 45 CFR 164.502(j)(1).

4. Obligations of the Government

Provisions for the Government to Inform the Business Associate of Privacy Practices and Restrictions

a. The Government shall provide the Business Associate with the notice of privacy practices that the Government produces in accordance with 45 CFR 164.520.

b. The Government shall provide the Business Associate with any changes in, or revocation of, permission by Individual to use or disclose Protected Health Information, if such changes affect the Business Associate’s permitted or required uses and disclosures.

c. The Government shall notify the Business Associate of any restriction to the use or disclosure of Protected Health Information that the Government has agreed to in accordance with 45 CFR 164.522.

5. Permissible Requests by the Government

The Government shall not request the Business Associate to use or disclose Protected Health Information in any manner that would not be permissible under the HIPAA Privacy Rule, the HIPAA Security Rule, or any applicable Government regulations (including without limitation, DoD 6025.18-R and DoD 8580.02) if done by the Government, except for providing Data Aggregation services to the Government and for management and administrative activities of the Business Associate as otherwise permitted by this clause.

6. Termination

a. Termination. A breach by the Business Associate of this clause, may subject the Business Associate to termination under any applicable default or termination provision of this Contract.

b. Effect of Termination.

(1) If this contract has records management requirements, the records subject to the Clause should be handled in accordance with the records management requirements. If this contract does not have records management requirements, the records should be handled in accordance with paragraphs (2) and (3) below

(2) If this contract does not have records management requirements, except as provided in paragraph (3) of this section, upon termination of this Contract, for any reason, the Business Associate shall return or destroy all Protected Health Information received from the Government, or created or received by the Business Associate on behalf of the Government. This provision shall apply to Protected Health Information that agents of the Business Associate may come in contact. The Business Associate shall retain no copies of the Protected Health Information.

(3) If this contract does not have records management provisions and the Business Associate determines that returning or destroying the Protected Health Information is infeasible, the Business Associate shall provide to the Government notification of the conditions that make return or destruction infeasible. Upon mutual agreement of the Government and the Business Associate that return or destruction of Protected Health Information is infeasible, the Business Associate shall extend the protections of this Contract to such Protected Health Information and limit further uses and disclosures of such Protected Health Information to those purposes that make the return or destruction infeasible, for so long as the Business Associate maintains such Protected Health Information.

7. Miscellaneous

a. Regulatory References. A reference in this Clause to a section in DoD 6025.18-R, DoD 8580.02, Privacy Rule or Security Rule means the section currently in effect or as amended, and for which compliance is required.

b. Survival. The respective rights and obligations of Business Associate under the “Effect of Termination” provision of this Clause shall survive the termination of this Contract.

c. Interpretation. Any ambiguity in this Clause shall be resolved in favor of a meaning that permits the Government to comply with DoD 6025.18-R, DoD 8580.02, the HIPAA Privacy Rule or the HIPAA Security Rule.

Section I - Contract Clauses

CLAUSES INCORPORATED BY FULL TEXT

52.252-2 CLAUSES INCORPORATED BY REFERENCE (FEB 1998)

This contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at this/these address (es):

FAR Clauses http://acquisition.gov/far/

DFAR Clauses http://www.acq.osd.mil/dpap/dars/dfars/index.htm

(End of clause) image1.wmf image2.wmf