D3951.pdf

Designation: D3951 − 10

Standard Practice for Commercial Packaging1

This standard is issued under the fixed designation D3951; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.

This standard has been approved for use by agencies of the Department of Defense.

1. Scope

1.1 This practice establishes minimum requirements for

packaging of supplies and equipment, exclusive of ammunition, explosives, or hazardous materials, as covered in Title 49 of the Code of Federal Regulations.

1.2 The values stated in inch-pound units are to be regarded

as standard. No other units of measurement are included in this standard.

1.3 This standard does not purport to address all of the

safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.

2. Referenced Documents

2.1 ASTM Standards:2

D996 Terminology of Packaging and Distribution Environ-ments

D1974 Practice for Methods of Closing, Sealing, and Rein-forcing Fiberboard Boxes

D4169 Practice for Performance Testing of Shipping Con-tainers and Systems

D5118/D5118M Practice for Fabrication of Fiberboard Ship-ping Boxes

D5168 Practice for Fabrication and Closure of Triple-Wall Corrugated Fiberboard Containers

D5445 Practice for Pictorial Markings for Handling of Goods

D6039/D6039M Specification for Open and Covered Wood Crates

D6251/D6251M Specification for Wood-Cleated Panelboard Shipping Boxes

D6254/D6254M Specification for Wirebound Pallet-Type Wood Boxes

D6255/D6255M Specification for Steel or Aluminum Slot-ted Angle Crates

D6256/D6256M Specification for Wood-Cleated Shipping Boxes with Skidded, Load-Bearing Bases

D6880 Specification for Wood Boxes D7478/D7478M Specification for Heavy Duty Sheathed

Wood Crates

2.2 Code of Federal Regulations:3

Title 49 Transportation (Parts 100 to 199)

2.3 Military and Federal Standards:4

MIL-STD-129 Military Marking for Shipment and Storage MIL-STD-2073–1 Standard Practice for Military Packaging FED-STD-123 Marking for Shipment (Civil Agencies)

2.4 International Standards:5

ISPM Publication No. 15 Regulation of Wood Packaging Material in International Trade (International Standards for Phytosanitary Measures (ISPM))

3. Terminology

3.1 Terminology found in Terminology D996 shall apply.

3.2 Definitions of Terms Specific to This Standard:

3.2.1 CONUS—Continental United States (excluding Ha-

waii and Alaska).

3.2.2 immediate use—used or consumed within seven days of receipt.

3.2.3 safe delivery—in packaging—delivery of a shipment to its destination with minimal damage to the package and no damage to the contents.

4. Significance and Use

4.1 This practice covers the requirements for the commer-

cial preservation, packaging, packing (exterior container),1 This practice is under the jurisdiction of ASTM Committee D10 on Packaging and is the direct responsibility of Subcommittee D10.18 on Miscellaneous Packag-ing.

Current edition approved Aug. 15, 2010. Published September 2010. Originally approved in 1980. Last previous edition approved in 2004 as D3951 – 98 (2004).

DOI: 10.1520/D3951-10.

2 For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards volume information, refer to the standard’s Document Summary page on the ASTM website.

3 Available from Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402.

4 Available from Document Automation and Production Service, Building 4/D, 700 Robbins Avenue, Philadelphia, PA 19111-5094,. http://assist.daps.dla.mil/ quicksearch..

5 Available from the International Plant Protection Convention at http:// www.aphis.usda.gov/import_export/plants/plant_exports/wpm/index.shtml.

Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States

Copyright by ASTM Int'l (all rights reserved); Tue May 28 13:22:54 EDT 2013 Downloaded/printed by DHS pursuant to License Agreement. No further reproductions authorized.

http://dx.doi.org/10.1520/D0996 http://dx.doi.org/10.1520/D0996 http://dx.doi.org/10.1520/D1974 http://dx.doi.org/10.1520/D1974 http://dx.doi.org/10.1520/D4169 http://dx.doi.org/10.1520/D4169 http://dx.doi.org/10.1520/D5118_D5118M http://dx.doi.org/10.1520/D5118_D5118M http://dx.doi.org/10.1520/D5168 http://dx.doi.org/10.1520/D5168 http://dx.doi.org/10.1520/D5445 http://dx.doi.org/10.1520/D5445 http://dx.doi.org/10.1520/D6039_D6039M http://dx.doi.org/10.1520/D6039_D6039M http://dx.doi.org/10.1520/D6251_D6251M http://dx.doi.org/10.1520/D6251_D6251M http://dx.doi.org/10.1520/D6254_D6254M http://dx.doi.org/10.1520/D6254_D6254M http://dx.doi.org/10.1520/D6255_D6255M http://dx.doi.org/10.1520/D6255_D6255M http://dx.doi.org/10.1520/D6256_D6256M http://dx.doi.org/10.1520/D6256_D6256M http://dx.doi.org/10.1520/D6880 http://dx.doi.org/10.1520/D7478_D7478M http://dx.doi.org/10.1520/D7478_D7478M http://www.astm.org/COMMIT/COMMITTEE/D10.htm http://www.astm.org/COMMIT/SUBCOMMIT/D1018.htm unitization, and marking for supplies and equipment. It pro-vides for multiple handling and shipment by any mode, and storage periods of a minimum of one year in enclosed facilities without damage to the product. It also provides for package quantities suitable for redistribution without additional repack-aging or marking. Planned storage that exceeds one year requires more than minimum requirements for physical and mechanical protection.

4.2 This practice is applicable to Department of Defense

shipments for:

4.2.1 Items intended for immediate use;

4.2.2 Items for not-mission-capable supply;

4.2.3 Items intended for depot operational consumption;

4.2.4 Small parcel shipments (CONUS), not-for-stock; and

4.2.5 Direct vendor deliveries (CONUS ONLY).

4.3 All other Department of Defense shipments shall be in

accordance with MIL-STD-2073–1.

5. Requirements

5.1 General—The following requirements, unless specifi-

cally changed by the contract or order, shall apply. Suppliers are encouraged to use advanced packaging technology.

5.1.1 Packaging—Preservation, packaging, packing, and

marking furnished by the suppliers shall meet or exceed the following minimum requirements:

5.1.1.1 Cleanliness—Items shall be free of dirt and other

contaminants which would contribute to deterioration of the item or which would require cleaning by the customer prior to use. Coatings and preservatives applied to the item for protec-tion are not considered contaminants.

5.1.1.2 Preservation—Items susceptible to corrosion or de-

terioration shall be provided protection such as preservative coatings, barrier protection, volatile corrosion inhibitors, or desiccated unit packs.

5.1.1.3 Cushioning—Items requiring protection from physi-

cal and mechanical damage or which are fragile shall be protected by wrapping, cushioning, pack compartmentization, cartonizing, or other means to mitigate shock and vibration to prevent damage during handling and shipment.

5.1.1.4 Loose-fill Cushioning/Dunnage —Loose-fill mate-

rial shall be prohibited for all Department of Defense (DoD) and/or General Services Administration (GSA) shipments and shipments to aerospace facilities.

5.1.2 Unit Package:

5.1.2.1 Unit Package— A unit package shall be so designed

and constructed that it will contain the contents with no damage to them, and with minimal damage to the unit pack during shipment and storage in the shipping container configuration, and shall allow subsequent handling.

5.1.2.2 Unit Package Quantity—Unless otherwise specified

in the contract or purchase order, the unit package quantity shall be one each part, set, or assembly, except for small lightweight items, for example, industrial hardware, which will be unit packaged in quantities that are standard in the trade and suitable for retail sales. Single items weighing over 5 lb shall be individually packaged.

5.1.2.3 Bulk packaging shall be specifically excluded unless

specified in the contract or purchase order.

5.1.3 Intermediate Package:

5.1.3.1 The use of intermediate packaging is encouraged

particularly when such use enhances handling and storage.

5.1.4 Packing:

5.1.4.1 Unit packages and intermediate packages not meet-

ing the requirements for a shipping container shall be packed in shipping containers.

5.1.4.2 Shipping Containers—The shipping container (in-

cluding any necessary blocking, bracing, cushioning, or water resistance) shall comply with the regulations of the carrier used and shall provide safe delivery to the destination. The shipping container shall be capable of multiple handling and storage periods at a minimum of one year in enclosed facilities without damage to the product. Table 1 provides suggested size and weight limits for shipping containers and may be used for unit and intermediate packages when specifying a fiberboard container, wood box, or crate.

5.1.4.3 All containers shall be tested to meet Practice D4169 test standards when specified in the contract or purchase order.

5.1.5 Unitization—Shipments should be considered for unit-

ization where appropriate or as specified in the contract or purchase order. Unitization encompasses, but is not limited to, bundling, consolidation in a container, or placement on a pallet.

5.1.6 Marking:

5.1.6.1 Unit and Intermediate Marking—Marking for the

unit and intermediate container shall mean those used in the commercial distribution or over-the-counter retail sales. The markings shall be sufficient to clearly and visibly identify the contents of the package. When the unit or intermediate container is also the shipping container the requirements of

TABLE 1 Weight and Size Limits of Shipping Containers

Container Standard Maximum Outside Dimensions, length + width + depth

Maximum Weight of Boxes and Contents (lb)

Practice D5118/D5118M SW Corrugated $40 and #105 in.

DW Corrugated $85 and #120 in.

#120 #180

Practice D5168 TW Corrugated $110 and #125 in. #300 Specification D6251/D6251MA As required #1000 Specification D6880A As required #1000 Specification D6256/D6256MA #16 ft #2500 Specification D6254/D6254MA As required #2500 Specification D6255/D6255MA As required #3000 Specification D6039/D6039MA As required #4000 Specification D7478/D7478MA 30 ft L × 9 ft W × 10 ft H #30 000

A Containers with length and width greater than 48 in. shall be designed with four-way entry lift capability. Containers with gross weight over 100 lb shall have 2-way forklift entry at a minimum.

D3951 − 10

DHS pursuant to License Agreement. No further reproductions authorized.

5.1.6.2 shall apply. Unless otherwise specified in the contract/ purchase order, the following are the minimum requirements:

(1) Part number and/or UPC barcode part number,

(2) Product name or nomenclature,

(3) Quantity and unit of issue,

(4) Manufacture retail markings,

(5) Country of origin marking,

(6) Shelf-life markings (expiration date/inspection date/ date of manufacture), if applicable,

(7) Storage legends, if applicable, and

(8) Precautionary markings, if applicable.

5.1.6.2 Shipping Container Markings—All markings shall

be legible, durable, and identify the contents of the package, and if required, include pictorial markings as identified in Practice D5445. Unless otherwise specified in the contract /purchase order, the following are the minimum requirements:

(1) Consignee and consignor address,

(2) Applicable precautionary markings,

(3) Part number and/or UPC barcode part number,

(4) Product name or nomenclature,

(5) Quantity and unit of issue,

(6) Manufacturer retail markings,

(7) Contract number/purchase order number,

(8) Country of origin marking,

(9) Shelf-life marking (expiration date/inspection date/date of manufacture), if applicable,

(10) Storage legends, if applicable, and

(11) Precautionary markings, if applicable.

5.1.6.3 Unitization Markings—All desired markings shall

be as specified in the contract /purchase order. All markings shall be legible, durable, and identify the contents of the shipment unit, and if required, include pictorial markings as identified in Practice D5445.

5.1.6.4 Wood Packaging Material (WPM)—If wood pack-

aging material is used for export from or import to the United States, the supplier shall comply with the requirements of ISPM Publication No. 15.

5.1.6.5 Container Markings for DoD—For all shipments to

the Department of Defense, the marking shall be in accordance with MIL-STD-129. Any additional marking requirements shall be specified in the contract or purchase order.

5.1.6.6 Container Markings for Government Civil

Agencies—For all shipments to government civil agencies, such as the General Services Administration (GSA), the marking shall be in accordance with FED-STD-123. Any additional marking requirements shall be specified in the contract or purchase order.

5.1.6.7 Items without Adequate Surface for Labels—Items

without adequate surface for labels shall be marked in accor-dance with 5.1.6.1 by means of a tag securely affixed to the item.

6. Options

6.1 Export Shipments—When permitted by the contract or

purchase order, this practice may be used for export shipments when favorable conditions are provided, such as containeriza-tion media and enclosed areas of receiving. Additional preser-vation methods and the use of weather-resistant grades may be required to ensure the packaging successfully protects the item in the export shipping environment. Ensure unit, intermediate and shipping containers are weather-resistant grades when shipping overseas. Containers should be sealed as opposed to closed (see Practice D1974).

7. Performance Testing

7.1 The use of Practice D4169 shall be required when

determining the performance level of a shipping unit.

7.2 The supplier shall be responsible for requirements

specified herein and in the contract or purchase order. The purchaser reserves the right to perform any or all of the tests.

7.2.1 Packaging used shall successfully pass the test levels

of Practice D4169, Distribution Cycle 1. Export shipments shall also pass the test levels of Distribution Cycles 15, 16, or 17 as appropriate. Assurance Level II shall be used. Acceptance shall be criterion I, no product damage.

7.3 Packaging shall be capable of successfully passing the

test levels of Practice D4169 Distribution Cycle 18 for ship-ments destined for delivery to the Department of Defense.

7.3.1 Shipments destined for delivery to an overseas loca-

tion as defined in the contract shall meet Assurance Level I.

7.3.2 Shipments destined for delivery to customers within

the continental United States shall meet Assurance Level II.

8. Keywords

8.1 commercial packaging; intermediate; packaging; preser-vation; unit package

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website (www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/

COPYRIGHT/).

D3951 − 10

DHS pursuant to License Agreement. No further reproductions authorized.