HQ0516017906 Salient Characteristics Doc.pdf

Test Equipment Purchase List Salient Characteristics

CLIN 0001: Promax Ranger Neo 3 with rack mount option:

Product Features:

1. Wi-Fi analyzer

2. Remote control with webControl mode:

a. Report generator

b. File manager

c. Channel plan editor

d. Control console with live streaming

e. Real time and historical monitoring

3. Merogram and Spectrogram

4. Fiber optics

5. DVB-T2/C2/S2, DSS, Dolby Digital Plus

6. ISDB-T/Tb

7. Network Delay Margin (DVB)

8. T2-MI analysis

9. GPS for drive test measurements

10. DAB and DAB+ digital radio

11. Advanced DAB/DAB+ analyzer (optional)

12. Super spectrum analyzer with Triple split display

13. IPTV analyzer

14. High resolution filters

15. TS-ASI input and output

16. Common Interface slot

17. Transport stream analyzer, recorder and player

18. Dynamic echoes analysis

19. Touch screen

20. HEVC H.265 decoding

21. Wide band LNB compatibility

22. More than 4 hours battery time.

Requirement: 1 each

CLIN 0002: Phabrix PHSXTAGC-IP (with IP Option):

Product Features:

Generator

1. Video Generator

a. Create video test signals for all supported SD and HD SDI output standards including

3GHz standards at 1080p/50/59/60 Y, Cb, Cr

b. Advanced video formats include support for RGB, XYZ 12bit and 2K formats

c. Fully programmable Y Zone Plate

2. Audio Generator

a. Embed audio signal on all 16 embedded audio outputs

b. Audio Group menu controls which audio channels are present, signal type and amplitude

c. Choice of: silence, adjustable tone, noise, AV Delay, Dolby test stream or AES input

3. Reference

a. Create video test signals that are either free-running or locked to studio reference or input signal

b. Genlock menu is used to select locking reference and provides control for genlock phase offset in lines and pixels

Analyzer

4. Picture Monitor

a. Picture is displayed in window adown-converted display

b. Cursor may be turned ON over area of picture specified by specific line and sample

c. Monitor device input or output

5. Picture Zoom

a. Zoom function provides 1:1 unfiltered pixel view, centred on position of picture cursor

b. HANC/VANC areas visible when cursor in blanking

6. Linked Cursors

a. Picture cursor is linked to waveform, vectorscope and data views for rapid and accurate detailed measurement of signal

7. Waveform Full Frame

a. Displays selected analyzer or generator source

b. Analog locking reference input view

c. YCbCr GBR, Y, Cb, Cr, R, G, B modes

d. Cursors may be displayed over the waveform to allow measurement of time or amplitude values

e. Vertical and horizontal magnifications

8. Waveform Line Select

a. Display may be restricted to single line or all lines may be displayed simultaneously

b. Single line display is linked to picture, vectorscope and data view

9. Vectorscope

a. Choice of 100% or 75% graticules

b. Display Composite, SDI, SFP video input or generator test pattern

c. Display specific video line linked to picture cursor

d. 1, x2, x5 or x10 magnifications with position to centre, cyan, yellow, green, magenta, red, blue graticule locations

Audio

10. 16 Channel Audio Meters

a. Display up to 16 audio channels

b. Source for each block of 8 meters may be independently set to allow metering of embedded audio inputs or outputs

c. Current audio level in dBFs (decibels relative to 0dB full-scale) is displayed at bottom of each meter

11. AES/Analog Audio Meters

a. AES and Analog (TAG) audio metering available as alternative to embedded audio

b. Dolby E metering selection

12. Audio Channel Status

a. Audio Status menu shows the Channel Status for selected audio channel

b. Displayed in decoded form as well as raw hexadecimal data dump

c. Source may either come from input signal or from generator output for rapid comparison purposes

System

13. Instrument Presets

a. Current instrument settings can be saved as memories for future recall

b. Memories can be exported to single files, reimported or copied to other units

c. Presets can be applied to whole instrument or selectively within Generator or Analyzer

14. Network Configuration

a. Network menu allows instrument to be configured as part of network

b. Support for automatic acquisition of network parameters via DHCP or manual configuration

c. Remote control enable/disable and selection of port number

15. Software Status

a. Serial number, instrument MAC address, version information and battery state listed

b. Date and time can be set and factory default settings recalled

c. Display of loaded license options

d. LCD brightness and screen saver configurations

16. Engineer Setup

a. Manage instrument's settings including user access, clearing memories, factory default reset, software upgrades and audio calibration

b. SDI input to SDI output loop through mode

c. Control of SDI to IP-SFP gateway in TAG

17. Utils

a. Details of the unit's operating status

b. Details the temperature and individual board voltages

c. Lists any hardware errors that have been recorded

Signal

18. Video Timing

a. Display relationship between selected video input with respect to external reference input

b. Offset feature to simplify system timing measurements

19. Video Status

a. Display the status of the selected video input or output and any errors that have been found in data stream

b. Display of EDH, Active Picture and CRC data with cumulative run-time display of errors and error rate

c. Display of estimated cable length for SDI inputs with selectable cable type

20. ANC Status

a. Shows which ANC packets are present on SDI input and whether any errors have been detected

b. Each field is color coded according to whether ANC packet is present (White), missing

(Grey), has errors (Red), or has previously had errors (yellow)

21. Video Format/Payload ID

a. Misc Status menu displays status of SMPTE 352 packets embedded in selected video input and displays any errors that have been found

b. Selection of input or output for rapid comparison

c. Display of raw data and decoded form

Logging

22. Log Setup

a. Set Audio Thresholds and log specific video status events, including Output, Reference and Input Status, TRS Errors, Picture CRC

23. Event Log Display

a. Event Log menu displays list of events with time stamp showing when they occurred

24. ANC Log Setup

a. Log ANC Status menu allows customization of which ANC packets to log for changes in status (e.g. Present, Checksum Error, Missing, Parity Error)

b. Logging of Dolby and AES Status as well as device system errors

c. Control of logging duration

Sx TAG Core Toolset

25. Composite Waveform

a. Waveform monitor can display waveform of the composite analog inputs

b. Selection of CVBS or Ref Input

26. Composite Chroma

a. Waveform monitor can display chroma component of composite waveform

27. Composite Luma

a. Waveform display of low pass filtering of composite waveform

28. Audio AES Eye

a. Real-time monitoring of 75Ω AES input allows amplitude and quality of AES waveform to be seen and allows relationship of AES input to be reference checked

29. SFP Status

a. All necessary status information for monitoring health of SFP and its interface

30. Vectorscope (Composite)

a. Vectorscope view of composite or external reference inputs

Requirement: 1 each

CLIN 0003: Decimator MD-Quad 3G/HD/SD-SDI Quad splitter Multi-viewer with

SD/HD/3G-SDI &HDMI:

Features

1. Low cost miniature (3G/HD/SD)-SDI 4 to 1 Quad Split Multiviewer or 4 to 1 input multiplexer

2. Selectable output format in Quad-Split mode

3. Low latency buffering for each input allowing non-synchronous inputs

4. Linked (3G/HD/SD)-SDI and HDMI outputs

5. 4 x (3G/HD/SD)-SDI inputs with auto detection (26 Formats supported in total)

6. 8-Channel Audio metering for each quadrant with:

7. The first two audio groups individually selectable

8. Vertical or Horizontal Bars

9. AES/EBU, VU, Extended VU, BBC, EBU, DIN and NORDIC Scales

10. Bar & Float, Bar only or Float only (Float is not available for MQS serials)

11. Transparency adjustment

12. Separate Bar and Float Ballistics control

13. Adjustable Reference level

14. Red, Yellow and Green Range adjustment

15. Bar thickness adjustment

16. Margin adjustment

17. Each quadrant is independent of the others, allowing any 3G/HD/SD format of any frame rate to be displayed simultaneously

18. Variable aspect ratios per quadrant

19. All 4 inputs can be displayed simultaneously on a single output

20. Pass-Through mode allowing any of the 4 inputs to be selected for output

21. In Pass-Through mode the selected input is passed through to both the (3G/HD/SD)-SDI and HDMI outputs

22. On-Screen 20 character IDs (UMDs) for each input

23. A single tallies for each input is available from the GPI

24. An extensive selection of user controllable functions via an easy to use rotary encoder for menu selection. LEDs and a push button can then be used for status and control

25. USB port for control and updates

26. GPI on RJ-45 for remote switching

27. Locking DC Power Socket

Requirement: 2 each

CLIN 0004: Fluke Networks DSX2-5000

Versiv 2 CableAnalyzer Copper Certifier with Integrated Wi-Fi

Product Features:

The DSX2-5000 Cable Analyzer is ideal for every step of the copper certification process Included WiFi adapter makes it easy to connect the Versiv 2 Mainframe to Linkware

Live Versiv 2 enables users to accomplish more than ever with a cable tester, by accelerating every step of the testing process ProjX management system eases tasks from initial set-up of a job to system acceptance. It eliminates redundant steps, and ensures that all tests are completed correctly the first time, and every time

Taptive user interface puts advanced data analysis and easy set-up and operation at the fingertips of technicians of all skill levels

LinkWare management software provides unmatched analysis of test results and professional test reports

The DSX reduces the time required to fix cabling faults with Dedicated Diagnostics, a simple test that locates the problem

Built in Alien Crosstalk testing capability

Performance:

Ten second Cat 6A test time contributes to the fastest way to gain certification

Graphically displays the source of failures including crosstalk and distance to shield faults for faster troubleshooting

Manage up to 12,000 test results with full graphics Capacitive touchscreen allows quick tester setup with easily selectable cable types, standards and testing parameters 1 billion links reported on LinkWare management software

Standards:

Compliant with proposed ISO (IEC WG9 Standard IEC61935-1) Level V accuracy requirements to 1000 MHz

Supports the complete suite of Resistance Unbalance standards needed for Power over Ethernet (PoE) - IEC61935-1 & 11801-1-4, IEEE 802.3af, IEEE 802.3at, ANSI/TIA/EIA-568-C.2

Next generation balance drafts - IEEE 802.3, TIA TR42.7

Requirement: 1 each

CLIN 0005: Tektronix, WFM7200 Multiformat Waveform Monitor

Product Features:

Multiformat, Multistandard Video Monitoring:

o WFM7200 includes standard auto-detection of HD/SD-SDI and multiple Dual Link video formats o Composite analog (PAL/NTSC) video support (Opt. CPS) o Simultaneous monitoring (Opt. SIM) allows monitoring of 2 HD/SD-SDI inputs or 1 HD/SD-SDI input and 1 CPS input. Option 3G is required for 3G-SDI format support o Multiple Input Mode allows monitoring of 2 to 4 SDI inputs simultaneously (4-input mode requires

Opt. 2SDI) o Upgradeable to 3G-SDI (Level A and Level B) format support (Opt. 3G)

Comprehensive Audio Monitoring (Opt. AD or DPE):

o Up to 16-channel audio monitoring for embedded audio o Multichannel Surround Sound*1 display and flexible Lissajous display o Audio Loudness monitoring to ITU-R BS.1770-2 (Opt. AD or DPE) o Support for analog, digital, and embedded audio (Opt. AD) o Dolby Digital (AC-3), Dolby Digital Plus, and Dolby E (Opt. DPE) o Comprehensive Dolby metadata decode and display (Opt. DPE) o Dolby E Guard Band meter with user-defined limits (Opt. DPE)

Unmatched Display Versatility:

o FlexVu™, the most flexible four-tile display, suited for various application needs to increase productivity o Tektronix-patented Diamond and Arrowhead displays for gamut monitoring o Tektronix-patented Timing and Lightning displays o New Tektronix-patented Spearhead display and Luma Qualified Vector (LQV™) display facilitate precise color adjustment for post-production applications (Opt. PROD)

Stereoscopic 3D Video Displays for Camera Alignment and Production/Post-production Applications (Opt. S3D)

Black Picture and Tektronix-patented Frozen Picture Detection

Advanced ANC Data Monitoring:

o Simultaneous CEA708/608 Closed Caption monitoring; Teletext and OP47 subtitle monitoring o Detect and decode ANC data including AFD, WSS, Video Index, TSID, V-Chip, Broadcast

Flag/CGMS-A, VITC, LTC, and ANC TC ARIB STD-B35/B37/B39, TR-B22, and TR-B23 support

In-depth Digital Data Analysis Helps Quickly Resolve Difficult Content Quality and Reliability Issues (Opt.

DAT)

Standard and User-definable Safe Area Graticules Facilitate Editing and Format Conversion Tasks, Reducing the Need for Reworks

Active Format Description (AFD) Detection, Decode, and Automatically Adjusted Graticule in Picture Display enable Easy Identification of Aspect-ratio Related Issues

Superior Physical Layer Signal Measurement:

o High-performance real-time eye pattern display, jitter measurements, and patented cable length measurement (Opt. PHY3) o Most comprehensive eye pattern measurements including eye amplitude, rise/fall time, and overshoot/undershoot measurements as well as Tektronix jitter waveform display (Opt. PHY3)

Unmatched Usability:

o CaptureVu advanced video frame data capture simplifies troubleshooting and equipment setup o 32 instrument presets for quick recall of commonly used configurations tailored to engineers or operators o Front-panel USB port enables easy transfer of presets, captured video frame data, screenshots, and error log o Front-panel headphone port enables quick verification of selected audio pair o Intuitive menu structure and context-sensitive help o Extensive alarms, status reporting, and error logging o Bright, crisp, high-resolution LED backlight display o SNMP and Ethernet remote interface capabilities and GPI control facilitate centralized monitoring and control

Applications

Monitoring and Compliance Checking in Content Distribution and Broadcast transmission

Quality Control in Content Production and Post-production

Equipment/System Qualification and Troubleshooting for Installation and Maintenance of Content Creation and Distribution Facilities

Post-production Edit Suite and Color Correction Monitoring

Requirement: 1 each