Home Rehabilitation 4418 Oak Dr.pdf

PDF 841 KB Posted

Attached to
Safe Home Rehab at 4418 Oak Drive
Solicitation number
HNS 27-6
Issued by
Mecklenburg County, Cleveland Town, North Carolina

About this file

This invitation to bid document is issued by the City of Charlotte Housing and Neighborhood Services for rehabilitation work under the Safe Home program at 4418 Oak Drive, Charlotte, North Carolina. The project encompasses comprehensive home rehabilitation including lead hazard abatement, HVAC system replacement with a minimum 90 AFUE gas pack and new digital thermostat, 200-amp electrical service upgrade with GFCI and AFCI breaker installation, roof tear-off and reroof with 30-year architectural shingles, exterior work including fascia and soffit replacement with aluminum or vinyl covering, interior electrical upgrades including new light fixtures and receptacles throughout the house, attic insulation to R-38, bathroom exhaust fan replacement, folding attic stairs replacement with insulation cover, and interior door and window replacements. The mandatory bid walk is scheduled for November 10, 2026 at 11:00 AM at the project address, with a bid opening on November 17, 2026 at 2:00 PM at 600 East Trade Street. All bids must be received by the specified date and time or will be deemed non-responsive and disqualified. Contractors arriving more than 10 minutes late to the bid walk will not be permitted to bid. The project specifications were dated October 7, 2026.

Bidders must submit sealed bids on provided forms with all line items priced, including separate pricing for lead hazard control work. To be considered a responsible bidder, contractors must be licensed general contractors in North Carolina, hold a current EPA Renovation, Repair & Paint Certification, not appear on local, state, or federal debarment lists, carry appropriate insurance, and provide references demonstrating completion of similar scope work within one year or successful prior Safe Home program work. The City awards rehabilitation bids to the lowest responsive and responsible bidder. All approved bids remain valid for 60 days following the bid opening date. The scope of work includes a separate lead hazard control section requiring North Carolina state-certified lead firm credentials and a state lead permit; all lead work must comply with applicable federal, state, and local regulations. Contractors must provide temporary toilet facilities, dust control methods, and coordinate debris removal without damaging the site. The project manager is Devin Smith, and the client is Sheila Linney, both reachable at (704) 589-2130.

View the file

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

SAFE HOME

CITY OF CHARLOTTE

Housing and Neighborhood Services

Invitation to Bid HNS 27-6 NOTE: Contractors are not authorized to visit the property before or after the bid walk, without being accompanied by the City’s Rehabilitation Specialist.

Documents included in Package:

1) Instruction to Bidders

2) Specs by Location/Trade (Scope of Work)

3) Subcontractor Certifications (if applicable)

4) Floor Plan / Site Drawing (if applicable)

Bid Walk & Bid Opening:

Project Address: 4418 Oak Dr – Safe Home, Lead, and Healthy Homes

Bid Walk: November 10, 2026 @ 11:00 AM

Bid Opening: November 17, 2026 @ 2:00 PM

Client Name: Sheila Linney

Project Manager: Devin Smith Contact Number: (704) 589-2130

Bid Walk and Bidding Instructions:

All bid walks are mandatory.

If you are going to be late the policy is the following:

Contact me BEFORE the start time if you are going to be late. If you are going to be more than 10 minutes late, we will proceed without you and you will not be permitted to bid.

The day of a bid walk the best way to reach me is at __ (704) 589-2130____________________

Bids must be received by the date, time and place specified. All others will be considered non responsive and disqualified.

The Bids will be opened at 600 East Trade St. immediately following the above due date and time.

The City of Charlotte is committed to making our services and programs accessible to all. To make a reasonable accommodation or language access request, please email hnsinfo@charlottenc.gov or dial 311.

Company Acknowledgment:

The undersigned, having become thoroughly familiar with the terms, conditions, limitations, and provisions of the housing improvement work to be performed at _4418

Oak Dr__ to be funded through the City of Charlotte Neighborhood & Business Services, in addition, having fully inspected the site in all particulars, hereby proposes and agrees to fully perform the work within the time stated and in strict accordance with the proposed contract documents including furnishing of any and all labor and materials, and to do all work required to complete said Work in accordance with the advised respective contractual, for the sum of money:

All labor, materials, services and equipment necessary for the completion of the Work shown on the Drawings and in the Specifications:

________________________________________________________Dollars_($___________)_

Written total

Specs Dated: 10/7/2026

Addenda # 1 Dated:

Addenda # 2 Dated:

Number of Pages: 11 Total

Number of Pages:

Number of Pages:

Project Schedule: Minimum Start Date ‐

Completion Deadline:

Please Print and Sign:

Company Name/Firm:

Authorized Representative Name:

Signature: Date:

reasonable accommodation or language access request, please email hnsinfo@charlottenc.gov or dial 311.

Requirements For Bidders

The City awards rehabilitation bids to the lowest responsive and responsible bidder.

A responsible bidder for the safe home program is one who:

1) Is a licensed general contractor in the State of North Carolina

2) Has a Renovate, Repair & Paint Certification (http://www2.epa.gov/lead/renovation-repair-and-painting-program)

3) Is not listed on a local, state or federal debarment list

4) Carries an appropriate amount of insurance

5) Can provide references verifying the contractor has completed work of a similar scope in a good workmanship like manner or successfully completed prior work for the Safe Home program. Referenced work must have been completed in one year or less from date of this invitation to bid.

A responsive bidder must:

1) Submit all requested documentation on time

2) Meet the above requirements for responsibility at the time of bid submittal

3) Have the capacity to meet the required schedule for the project

4) Existing rehab projects contracted by the contractor must be on schedule

The City reserves the right to waive any minor informalities or irregularities, which do not go to the heart of the bid submittal or prejudice other offers, or to reject, for good and compelling reasons, any or all bid submittals.

Rehabilitation Specialist – Devin Smith City of Charlotte Neighborhood and Business Services 600 E. Trade St.

Charlotte, NC 28202

PH: ( 7 0 4 ) 5 8 9 - 2 1 3 0

Fax:

reasonable accommodation or language access request, please email hnsinfo@charlottenc.gov or dial 311.

Instructions to Bidders

Explanations to Bidders

Any explanation desired by a Contractor regarding the meaning or interpretation of the advertisement for bids, drawings, specifications, etc., must be requested in writing to the

Rehabilitation Specialist with sufficient time allowed for a reply to each Contractor before the submission of their bids. Any interpretation made will be in the form of an addendum to the invitation for bids, drawings, specifications, etc., and will be furnished to all prospective

Contractors. The Contractor must acknowledge any revision to the bid documents in the space provided on the bid form and it must be submitted with their bid package.

Preparation of Bids

Bids shall be submitted on the forms furnished, or copies thereof, and must be manually signed. If erasures or other changes appear on the forms, the person signing the bids must initial each erasure or change

• The Contractor’s Bid Proposal must be properly executed and submitted on the form provided. Bids by Contractors must be received by the Rehabilitation Specialist at the time and place specified on the “Invitation to Bid”

• No bid will be considered unless all individual work items on the Bid Form including any addendums are priced. The sum of all work items must equal to the Total Bid Amount.

• Unless called for, alternate bids will not be considered

• Modification of bids already submitted will be considered if received at the office designated in the invitation for bids by the time set for opening of bids

Submittal of Bids

• Sealed bids will be submitted to the Safe Home Program Office as directed in the invitation to bid prior to or at the appointed bid opening time

• Bid will be time stamped on the date of delivery

• Each bid must be submitted in a sealed envelope bearing on the outside the name of the Contractor, the name of the project for which the bid is submitted, and the date and time of the bid opening

• All bids submitted must be typed or written in ink and signed by the Contractor's designated representative

• Failure to include all forms may result in rejection of a bid

• Required Bid Package Forms:

reasonable accommodation or language access request, please email hnsinfo@charlottenc.gov or dial 311.

o Scope of Work o Addenda Acknowledgement o Itemized Work Sheet o Subcontractor Certifications (if applicable)

Bid Validation

• All approved bids will be valid for 60 days after the bid opening date

HOUSING AND NEIGHBORHOOD SERVICES

http://housing.charlottenc.gov | 600 E. Trade Street | Charlotte, NC reasonable accommodation or language access request, please email hnsinfo@charlottenc.gov or dial 311.

City of Charlotte Housing and Neighborhood Services

600 E. Trade Street Charlotte, NC 28202

704-336-7600 10/7/2026

Address:4418 Oak Drive Unit: Unit 01

Location: 1- General Requirements Approx. Wall SF: 0 Ceiling/Floor SF: 0

Spec # Spec Quantity Units Unit Price Total Price

Trade: 1 General Requirements

1 Custom Lead Abatement Scope ________ ________

See attached scope. An allowance to complete the scope of work attached.

Location Total: ____________

Location: 2- Exterior Approx. Wall SF: 0 Ceiling/Floor SF: 0

Trade: 21 HVAC

2 0131 HEATING AND AIR CONDITIONING EQUIPMENT INSTALL ________ ________

Remove all existing HVAC equipment and dispose of properly.

Perform Manual J calculations for the house room by room that account for all changes included in the scope of work.

Use Manual S to select the proper equipment for the house.

Provide Manual J and S calculations and design specifications for the selected equipment to the rehab specialist for review and approval.

1. Gas Pack Install the approved gas pack at the existing location.

Gas-fired equipment shall have a minimum AFUE of 90.

Installation includes inspection and replacement as necessary of gas lines and connections and exhaust venting.

Install the equipment complete with all devices, connections, refrigerant, and accessories necessary to produce a fully functioning HVAC system meeting all the requirements of the NC Mechanical and Electrical Codes as well as the

Location: 2- Exterior Approx. Wall SF: 0 Ceiling/Floor SF: 0

Construction Specifications.

Install a new digital programmable thermostat.

Scope of work includes all repairs to the structure and finish surfaces that are necessary due to the removal of the old system and the installation of the new system.

Scope of work includes start-up and testing of the new system, including demonstrating to the customer how to operate the thermostat and change the return air filter.

Provide rehab specialist and homeowner with all installation manuals, user manuals, and warranty documentation.

Trade: 23 Electrical

3 0147 200 AMP ELECTRICAL SERVICE ________ ________

Replace the electrical service with a new 110/220-volt, 200-amp panel with a main disconnect and 24-circuit panelboard;

meter socket; service raceway; service cable; and ground rods and cable. Caulk exterior service penetrations. Label circuits legibly.

Replacement of all sub-panels is included.

Install GFCI breakers on all two-wire receptacle circuits. Install GFCI/AFCI breakers on all bedroom receptacle circuits. Label outlets per Code requirements.

4 0166 Light Fixture Exterior ________ ________

Replace or install UL-approved LED light fixtures at all entrances. Owner's choice of style and finish.

Trade: 32 Roof/Chimney/Gutters/Downspouts

5 067 Tear Off & Reroof Shingles ________ ________

Remove and dispose of existing roofing, inspect and repair roof deck (include 160 sq.ft. of decking replacement in bid), and install new 30-year architectural shingles. Provide the homeowner with a minimum of 3 color options. Include ice and water shield at all roof edges, felt paper, shingle over ridge vent, boots, flashing, and all necessary accessories.

Repair/replaced all damaged or decayed fascia, rafters, ceiling joists, or other roof/attic area framing.

Location Total: ____________

Location: 3- Interior Approx. Wall SF: 0 Ceiling/Floor SF: 0

6 0135 HALLWAY BATH FAN ________ ________

Replace ceiling-mounted Energy Star-rated exhaust fan. The fan shall be quieter than 2 sones and move air at 100 CFM.

Proper installation of metal vent and roof or wall cap/damper assembly is included.

Installation of all necessary wiring for fan and switch is included.

All materials and work shall comply with the Electrical and Mechanical Codes.

Repair all ceiling and wall damage caused by the installation.

7 0148 Light Fixture Replace

Replace the hall bathroom wall-mounted 4-bulb LED strip light fixture with a UL-approved fixture with shade and lamps. Also replace the kitchen sink and under-cabinet light fixtures with 24" LED strip light fixtures.

8 0153 GFCI Receptacle 20 AMP

Install a flush-mounted, ground fault circuit interrupter (GFCI) duplex receptacle and cover plate in the hallway bathroom.

Fish wire and repair any tear-out as needed.

9 0170 SMOKE AND CARBON MONOXIDE DETECTORS

Install UL-approved ceiling-mounted smoke and heat detectors permanently hardwired into outlet boxes with battery backups in all bedrooms and outside of all sleeping areas.

Detectors in the hallway shall be a combination

CO/smoke detector.

All detectors shall be interconnected so that when any one detector goes off, all other detectors also go off.

Installation shall comply with all requirements of the Electrical Code SMOKE AND CARBON MONOXIDE DETECTORS

10 0172 Demo or Terminate Wires

Completely eliminate the exposed, abandoned wires behind the oven. Disconnect and dispose of the existing in cabinet wall oven, outlet, and circuit. If unable to completely demo, terminate the existing wires in a code-approved junction box. Repair all wall tear-out as required.

11 0176 Disconnect dishwasher electrical

Verify 120V is present, and the existing dishwasher is operational. Disconnect the electrical supply feeding the dishwasher and make safe in an enclosed, secure junction box.

12 0185 Oven Circuit

Reroute oven circuit within walls so that all conductors are concealed or otherwise protected from physical damage.

Terminate conductors in an approved junction box or receptacle box with proper cable clamps/strain-relief. Replace outlet as required.

Test circuit operation, verify grounding and polarity, and correct any related electrical deficiencies discovered during this work.

Repair all wall tear-out as required.

13 0186 REPLACE RECEPTACLES, SWITCHES AND COVER ________ ________

PLATES

Replace all existing receptacles, switches, device cover plates, and blank covers throughout the entire house (including the exterior, attic, and crawlspace).

Replace all two-prong receptacles with three-prong receptacles.

Install GFCI breakers on all two-wire receptacle circuits.

Install GFCI/AFCI breakers on all bedroom receptacle circuits.

Label outlets per Code requirements.

Receptacles in Code-defined wet or damp locations shall be GFCI protected.

Scope includes repair of any wall or ceiling damage.

14 7577 KITCHEN RECEPTACLE--20 AMP CIRCUIT ________ ________

Install an additional dedicated 20-amp kitchen countertop circuit and a new GFCI-protected outlet on the left side of the kitchen counter. Evenly divide the number of countertop receptacles between the two kitchen countertop circuits. Fish wire as required and repair all tear-out.

Trade: 36 Insulation

15 0266 ATTIC INSULATION ________ ________

Remove the homeowner's items stored in the attic, along with the existing attic insulation, and dispose of both properly.

Install a wooden or plywood dam around the access hatch high enough to hold back R-38 insulation.

Install continuous foam insulation around the perimeter of the panel where it rests on the casing. Glue an R-38 insulation batt cut to size on the top of the panel.

Install ventilation baffles per the Building Code.

Install insulation depth markers readily visible from the attic access hatch.

Blow in insulation to increase R value to R-38.

Attach insulation certificate to rafter at attic access, positioned

Trade: 36

Trade: 38

Insulation to be easily seen.

Stairs/Steps

16 0286 Folding Attic Stairs ________ ________

Replace the utility folding stairway and install or adjust framing as needed to ensure proper installation in accordance with the manufacturer's specifications. Install casing that matches the existing trim in the room. Prime and paint the door and casing.

Additionally, install a sealed, manufactured insulation cover over the attic stairs to achieve a minimum R-10 insulation value.

Location Total:

Unit Total for 4418 Oak Drive, Unit 01:

Address Grand Total for 4418 Oak Drive:

Bidder: _________________________________________________

Scope of Work for Lead Hazard Control

Address: 4418 Oak Dr Date: 10/7/2026

All work described must be performed by a North Carolina state-certified lead firm, and a state lead permit is required. All work must comply with all applicable federal, state, and local regulations. Provide a separate price for each line item and add the total of line items at the end of the scope. Transfer the lead scope total to the lead control line item in the main scope of work.

Lead Hazard (from LIRA) Method of Control and Scope of Work Number Unit Line- Cost Item

Cost

EXTERIOR

Side A through Side D – beige wood fascias, soffits, crown moldings and trim boards (Note: It appears some of the fascia boards have been randomly replaced.)

Remove and properly dispose of all gutters, downspouts, light fixtures, and crown molding.

Remove the existing satellite dish, electrical, and supports; store them safely for reinstallation. Install new white K-type .027-gauge seamless aluminum gutter to service the roof, with sufficient pitch to the new downspouts, in accordance with construction manual specifications. Install 4” corrugated black pipe with the proper connectors to each downspout.

Pipe length shall be sufficient to ensure roof runoff flows away from the foundation. Remove and replace all missing, damaged, loose, or rotted material associated with the required repair. Cover fascia, soffits (including vents; install new where needed), trim boards, and drip boards with Tyvek and aluminum or vinyl. Reroute and support all existing cabling. Replace all floodlight fixtures with new LED fixtures and ensure they are operational.

Door A1 (to Room 1) – beige wood door casings, header, jambs and stops

Remove the entire existing door assembly, including the threshold and storm door, and dispose of it properly. Install a new Energy Star-rated pre-hung metal exterior door, storm door, and threshold.

Owner's choice of door style, color, and hardware finish. Insulate the cavity. Install a single-cylinder deadbolt and a lever-handled entry set, keyed alike.

New casing and shoe molding will match the existing.

Apply primer and topcoat. Install a new aluminum combination storm and screen door. Inspect from the crawlspace during the bid walk; this installation includes replacing all damaged, loose, or rotted material associated with the required repair.

INTERIOR

Room 4 – Door D1 – beige wood door casings, header, jambs and stops

Room 1 – Window A1, Window A2 and Window A3 – beige vinyl mini-blinds (lead contained within the matrix of the vinyl)

Make smooth and operable, scrape loose paint, and repaint. Owner's choice of color.

Remove, properly dispose of, and replace with new.

Owner's choice of color and style.

Room 2 – Window C1 – beige vinyl mini-blind (lead contained within the matrix of the vinyl) Room 3 – Closet D1 – beige vinyl vertical blind door (lead contained within the matrix of the vinyl)

Room 8 – Window A1 and Window D1 – beige vinyl mini-blinds (lead contained within the matrix of the vinyl)

Throughout – elevated lead dust levels

Complete specialized cleaning throughout the house.

All contractor requirements

The contractor is responsible for all project requirements, including but not limited to:

Obtaining all permits required. Said permits shall include all items in this scope of work.

Provide temporary toilet facilities from job start through completion of work.

Provide AS MANY roll-off dumpsters as needed without damaging the site. Collect construction debris using dust control methods. Remove dumpsters and repair any evidence of dumpster use.

Contractor may haul debris away daily using dump trailers or trucks.

Total Bid for Lead Scope $

Housing and Neighborhood Services

File details come from the government source that posted it. Updated .