HC101322QA265-0001.v0.pdf

IQO INQUIRY

FM: PL8211

TO: Contractors

DATE (MM/DD/YYYY): 5/3/2022

SUBJECT: HC101322QA265-0001 Amend: 0001

A. TYPE ACTION: AMEND

1. PURPOSE: *******THE PURPOSE OF THIS AMEND IS TO REMOVE THE REQUIREMENT

FOR BURIED FIBER. ALL ELSE REMAINS UNCHANGED.********

1. SUBMIT A QUOTE TO PROVIDE, INSTALL, AND MAINTAIN A 2.5GB WAVE SERVICE

BETWEEN BLDG 700, ROOM 104A, 362

OTIS STREET, ROME, NY AND BLDG 308, ROOM 203, 5450 CARLISLE PIKE,

MECHANICSBURG, PA FOR 60 MONTHS WITH NO BASIC

TERMINATION LIABILITY (BTL).

2. CONTRACTORS MUST ADDRESS IN QUOTES COMPLIANCE WITH TESTING AND

ACCEPTANCE REQUIREMENTS WITH “UNDERSTAND AND WILL COMPLY”

3. TESTING & ACCEPTANCE REQUIREMENTS MUST BE COORDINATED WITH GOVERNMENT

POC AT BOTH LOCATIONS BEFORE NOTICE OF COMPLETION IS SUBMITTED TO DITCO.

4. CONTRACTORS ARE RESPONSIBLE FOR READING AND ADDRESSING ALL TECHNICAL

REQUIREMENTS OF THIS INQUIRY/SOLICITATION, READING AND AGREEING WITH THE

STANDARD PROVISIONS, PROVIDE PRICE QUOTATION IN ACCORDANCE WITH STANDARD

PROVISION 4, AND MEET THE REQUESTED SERVICE DATE.

5. THE SERVICE DATE TO BE MET IS: 5 SEP 2022 (SIP) TO COMPLY WITH PROCUREMENT

ACQUISITION LEAD TIME (PALT) FOR THIS TYPE OF SERVICE.

6. CONTRACTORS MUST CONSIDER ALL ISSUES THAT MAY DELAY THE DELIVERY OF

CIRCUIT ON APPROVED SERVICE DATE. THE GOVERNMENT MAY CANCEL, TERMINATE,

OR REQUEST CONSIDERATION IAW STANDARD PROVISION 42 FOR FAILURE TO MEET

CONTRACTUAL SERVICE.

7. QUOTES MUST INCLUDE NAME AND INFORMATION ABOUT SUB-CONTRACTOR/LONG

HAUL PROVIDER/OTHER CARRIER INSTALLING CIRCUIT IS ON NET/OFF NET, RTD, JUMBO

FRAMING, TESTING AND OTHER APPLICABLE TECHNICAL INFORMATION. FURTHERMORE,

IF A BUILD IS REQUIRED TO INSTALL, VENDOR MUST INDICATE THE SCOPE OF THE BUILD

(LENGTH, BURIED/AERIAL, TRENCHING/DIRECTIONAL BORING, NEW CONDUIT, ETC.)

VENDOR MUST ALSO INDICATE IF SITE POC (S) HAVE ADVISED THAT PERMISSION FOR

BUILD AT SITE (S) WILL BE GRANTED, AND IF SITE (S) HAVE SUFFICIENT SPACE, POWER

AND HVAC CAPACITY TO SUPPORT VENDOR EQUIPMENT AND CABLING. MAPS/BLOCK

DIAGRAMS ARE AN ACCEPTABLE WAY TO PROVIDE THIS INFORMATION.

HC101322QA265-0001

8. QUOTES MUST BE UPLOADED TO IDEAS. THE GOVERNMENT IS NOT RESPONSIBLE

FOR MISSING OR OVERLOOKED QUOTES. CONTRACTORS ARE INSTRUCTED TO SUBMIT

QUESTIONS AND REQUEST CLARIFICATIONS OF REQUIREMENT (S) BEFORE SUBMITTING

QUOTES. IN RESPONSE TO THIS SOLICITATION, NO TERMS OR CONDITIONS PLACED UPON

THE GOVERNMENT, NOR ASSUMPTIONS WILL BE ACCEPTED.

9. THIS REQUIREMENT MUST BE WORKED IN CONJUNCTION WITH SOLICITATION

HC101322QA283/TSR SG15MAR227238 AND MUST BE ENGINEERED AND PROVISIONED

TOTALLY DIVERSE END TO END FROM THE GOVERNMENT SERVICE DELIVERY POINTS

(SDP) FROM TSR SG15MAR227238 ; MEANING THE PHYSICAL PATHS ARE TOTALLY

SEPARATE INCLUDING MAN HOLES, CONDUIT, CENTRAL OFFICE LOCATIONS, AND FIBER

BUILDS. ADDITIONALLY AS A MINIMUM MUST HAVE 50 METERS PHYSICAL SEPARATION

FROM TSR SG15MAR227238 .

10. CONTRACTOR SHALL PROVIDE COLOR POWERPOINT DRAWINGS SHOWING THE

ROUTES FROM THE COMMERCIAL DEMARKS TO THE SUPPORTING CENTRAL OFFICES AND/

OR WIRING CENTERS, ENSURING THE PHYSICAL END TO END DIVERSITY REQUIREMENTS

ARE BEING MET. DRAWINGS MUST INCLUDE SEPARATION DISTANCES, TOTAL FIBER MILES

AND ROUND TRIP DELAY BASED ON ACTUAL DISTANCE IN MILES. REFER TO STANDARD

PROVISION 39 FOR SPECIFIC DOCUMENTATION REQUIREMENTS. SAMPLE DRAWINGS

INCLUDED WITH INQUIRY/SOLICITATION SHALL BE FOLLOWED IN ORDER TO PROVIDE THE

REQUIRED TECHNICAL INFORMATION. MAPS AND DRAWINGS WITH ERRORS, MISMATCH

INFORMATION, MISSING RTD, AND NOT ENOUGH DETAIL TO DETERMINE DIVERSITY

THROUHGOUT THE FIBER PATH WILL BE FOUND TECHNICALLY DEFFICIENT AND WILL NOT

BE ACCEPTED.

11. PRE AWARD SITE SURVEYS ARE AUTHORIZED (AT CONTRACTOR EXPENSE) AND

SHOULD BE CONDUCTED IN COORDINATION WITH LOCAL POCS AT EACH GOVERNMENT

SITE.

12. AWARDS OF DIVERSE REQUIREMENTS WILL ONLY BE SPLIT BETWEEN TWO

CONTRACTORS IF THE DIVERSITY, RTD, SERVICE DATE AND LOWEST PRICE

REQUIREMENTS ARE PRESERVED.

13. ESTABLISH TSP: TSP0EWRC5-01

14. THIS REQUIREMENT MUST BE ENGINEERED AND PROVISIONED TOTALLY DIVERSE

END TO END TO GOVERNMENT'S SERVICE DELIVERY POINTS (SDP'S) FROM CJON:

SG15MAR227238, MEANING THAT PHYSICAL PATHS ARE TOTALLY SEPARATE INCLUDING

MAN HOLES, CONDUIT, (CENTRAL OFFICE LOCATIONS), AND FIBER BUILDS. THE

TELECOM PROVIDER MUST PROVIDE DITCO COLOR POWERPOINT DRAWINGS FOR

TECHNICAL REVIEW SHOWING THE ROUTES FROM THE COMMERCIAL DEMARCS TO

THE M. SUPPORTING CENTRAL OFFICES AND/OR WIRING CENTERS. DRAWINGS MUST

INCLUDE SEPARATION DISTANCES BETWEEN DIVERSE REQUIREMENTS, TOTAL FIBER

MILES AND ROUND TRIP DELAY (RTD), AND FIBER ROUTES RED LINED END TO END SO

THE GOVERNMENT CAN CONFIRM PHYSICAL END TO END DIVERSITY REQUIREMENTS

ARE MET. ADDITIONALLY, THE VENDOR IS TO PROVIDE DITCO WITH DETAILED CIRCUIT/

PATH CONNECTIVITY DIAGRAMS, IN KMZ OR KML FORMAT, IDENTIFYING ALL POINTS OF

PRESENCE (POP) FOR EVALUATION AND AS A FINAL RECORD OF THE INSTALLED PATH. 8.

THE VENDOR MUST PROVIDE LIGHT LEVEL READINGS (SIGNAL STRENGTH IN DBM) ON THE

EXTENSION FROM COMMERCIAL POP TO THE GOVERNMENT SERVICE DELIVERY POINT

(SDP) AT THE "A" AND "Z" LOCATION PRIOR TO CIRCUIT TURN OVER TO THE GOVERNMENT

ENSURING LEVELS ARE WITHIN SPECS. LIGHT LEVELS MUST BE ADJUSTED TO -3 TO -9

DBM. 9. THE VENDOR MUST TERMINATE 10GB ETHERNET SERVICE AT SERVICE DELIVERY

LOCATIONS, IAW UNIQUE INSTALLATION FACTORS. 10. THE VENDOR MUST CONDUCT

WALK-THROUGH SITE SURVEY PRIOR TO INSTALLATION AT BOTH LOCATIONS. 11. THE

VENDOR MUST CONTACT DISA GOC IP BACKBONE ENGINEERING AND IMPLEMENTATION

GROUP UPON RECEIPT OF A VALID TSO TO ESTABLISH THE COORDINATION AND

ACTIVATION PROCESS. PHONE: (C) 618-418-8627, (D) 418-8627. 12. THE VENDOR MUST

CONTACT DISA GOC TIER-II ENGINEERING 48 HOURS PRIOR TO BEGINNING THEIR END-

TO-END TESTING. PHONE: (C) 618-418-8627, (D) 418-8627. 13. THE PROVIDER MUST

CONDUCT A SATISFACTORY 24-HOUR TEST FROM THE DROP SIDE OF THEIR OR LOCAL

EXCHANGE CARRIERS FDP INSTALLED IN THEIR EQUIPMENT SUITE AT THE "A" LOCATION

TO THEIR OR LOCAL EXCHANGE CARRIERS FDP INSTALLED IN THEIR EQUIPMENT SUITE

AT THE "Z" LOCATION AND MUST INCLUDE THE EXTENSION BETWEEN THE COMMERCIAL

DEMARC AND THE GOVERNMENT'S SDP. VENDOR MUST ENSURE N. TEST & ACCEPTANCE

INSTRUCTIONS: TEST SETS ARE PLACED AT THE DROP SIDE AT THE "A" LOCATION AND

AT THE "Z" LOCATION. TESTING MUST BE SATISFACTORY PRIOR TO TURN OVER TO THE

GOVERNMENT FOR ACCEPTANCE TESTING. THE VENDOR MUST TEST THE CIRCUIT FOR

24 HOURS IAW THE FULL ITU-T.Y.1564 BENCH MARKING METHODOLOGY FOR NETWORK

INTERCONNECT DEVICES STANDARD, AND AT THE COMMITTED INFORMATION RATE (CIR)

IAW ITU-T-Y.1564.

CIRCUIT REQUIRES THE FOLLOWING PARAMETERS: (A) FIBER TERMINATION: FRAME

FORMAT: 10GB ETHERNET (OPTICAL HANDOFF-10GB ETHERNET-LAN-PHY-SINGLE MODE

FIBER), 1310NM. "SC" OR "LC" CONNECTORS AS DETERMINED BY SITE SURVEY. NOTE:

WHEN EXTENDED REACH OPTICS ARE USED THAT CHANGE THE TX/RX WAVELENGTH OF

THE OPTIC, THE VENDOR WILL NOTIFY THE GOVERNMENT 30 DAYS PRIOR TO DELIVERY.

(B) COMMITTED INFORMATION RATE (CIR): 10GB. (C) ETHERNET FRAME SIZE WILL BE

CONFIGURED TO SUPPORT MAXIMUM TRANSMISSION UNIT (MTU) OF 9000 OCTETS BYTES)

JUMBO FRAMES. (D) NO NETWORK INTERFACE UNIT, DEDICATED PATH. (E) GFE CLOCKING:

VENDOR ESFU (OR EQUIVALENT) NOT TO BE ENGINEERED INTO CIRCUIT.

(F) TESTING CRITERIA: VENDOR MUST TEST THE CIRCUIT FOR 24 HOURS IAW THE FULL

ITU-T.Y.1564 BENCH MARKING METHODOLOGY FOR NETWORK INTERCONNECT DEVICES

STANDARD, AND AT THE COMMITTED INFORMATION RATE (CIR) IAW ITU-T-Y.1564. NOTE:

ETHERNET FRAME SIZE DESIGNATOR 'H' (MTU) IS EQUAL TO 9000 BYTES. (G) LINE MUST

REMAIN FULLY OPERATIONAL AND AVAILABLE TO USERS 24 HOURS A DAY, SEVEN DAYS

PER WEEK, MONTHLY PERFORMANCE OF 99.5% AVAILABILITY OR BETTER.

(H) 1 HOUR RESPONSE TIME TO RESPOND TO CUSTOMER UPON RECEIPT OF TROUBLE.

(I) VENDOR REQUIRED TO HAVE CIRCUIT VISIBILITY TO ASSIST IN ANY CIRCUIT OUTAGES.

(J) VENDOR MUST HAVE A 24X7 NETWORK OPERATIONS CENTER. (K) TELECOM PROVIDER

MUST MAINTAIN OPERATIONS, MAINTENANCE AND ADMINISTRATION MONITORING OF

ETHERNET CIRCUIT. O. REMARKS CONTINUED: (L) THE COMMERCIAL CIRCUIT WILL

BE ACCEPTED ON BEHALF OF THE GOVERNMENT BY THE DISA GOC IP BACKBONE

ENGINEERING AND IMPLEMENTATION GROUP, SCOTT AFB, IL. (C) 618-418-8627, (D)

418-8627. 2. VENDOR WINNING AWARD IS RESPONSIBLE FOR INSTALLATION AND

MAINTENANCE OF THE SERVICE IAW THE UNIQUE INSTALLATION FACTORS. 3. INSIDE

WIRING IS AUTHORIZED IAW THE UNIQUE INSTALLATION FACTORS. 4. VENDOR MUST

COORDINATE SITE VISIT WITH POC'S 72 HOURS IN ADVANCE PRIOR TO REQUIRING

ACCESS TO FACILITIES AT BOTH USER LOCATIONS. 5. VENDOR MUST CONTACT DISA GOC

TIER-II ENGINEERING 48 HOURS PRIOR TO BEGINNING THEIR END-TO-END TESTING. 6. ALL

EQUIPMENT AND CIRCUIT PROBLEMS WILL BE REPORTED BY PHONE TO THE DISA GOC

IP BACKBONE ENGINEERING AND IMPLEMENTATION GROUP, SCOTT AFB, IL. PRIMARY: (C)

618-418-9950, (D) 418-9950 TOLL FREE: 855-868-9950.

MINIMUM TECHNICAL SPECIFICATIONS: SPECIFIC FORMAT TO BE USED IS: LINE RATE:

10.3125 GIGABITS/S, +- 100 PPM LINE CODE: OPTICAL 1. TEST AND ACCEPTANCE: THIS

CIRCUIT SHALL PASS A FULLY DOCUMENTED, SATISFACTORY, 72 HOUR SOAK TEST

BY DISA GOC AT SCOTT AFB, IL. PRIMARY: (C) 618-418-8627 (D) 418-8627. 2. ERROR

PERFORMANCE: ERROR PERFORMANCE SHALL BE BETTER THAN THE FOLLOWING

PARAMETER THRESHOLDS TO BE ACCEPTABLE: AVAILABILITY SHALL BE GREATER THAN

99.5% OR BETTER. FRAME LOSS SHALL BE EQUAL TO ZERO WHEN TESTING AT 10 GIGABIT

HIGHEST FRAME RATE, AND SHALL MEET ITU-T-Y.1564 STANDARDS. JITTER SHALL BE

LESS THAN 3 MSEC. DELAY SHALL BE BETTER THAN 10 MSEC. 3. MEAN TIME TO LOSS

OF BIT COUNT INTEGRITY (MTTLBCI) SHALL P. REMARKS CONTINUED: BE GREATER

THAN 24 HOURS. 4. ROUND TRIP DELAY (RTD) FOR THIS DISA TRANSPORT TRUNK WILL

BE MEASURED IN MILLISECONDS FROM THE CUSTOMER'S SERVICE DELIVERY POINT

(SDP) SITE-A TO THE CUSTOMER'S SERVICE DELIVERY POINT (SDP) SITE-Z. THE RTD

SHALL BE LESS THAN OR EQUAL TO 10 MILLISECONDS TO EFFECTIVELY SUPPORT THE

GOVERNMENT'S MISSION. THE GOVERNMENT ACCEPTING AUTHORITY WILL CONFIRM

THE RTD DURING THE TURN-UP AND TEST PHASE AND IF IT DOES NOT ALIGN WITH THE

CONTRACTORS PROPOSAL, DISA IE161 WILL NOTIFY DITCO IMMEDIATELY IN WRITING.

15. THIS IS A REAWARD OF A CURRENT SERVICE, (CSA#GGTG000113EBM). IF THE

INCUMBENT QUOTE IS EVALUATED AS THE LOWEST PRICE TECHNICABLE ACCEPTABLE,

THE CURRENT CSA WILL BE ADMINSTRATIVELY DISCONTINUED USING THE DATE PRIOR TO

THE START DATE OF NEW CSA.

M. ADDITIONAL INFORMATION:

3. TSR NUMBER: SG15MAR227235

4. CCSD: DIYU6EX2

Z. DITCO CONTACT:

Benjamin Sparlin

618-418-6836 benjamin.r.sparlin.civ@mail.mil

Angelina Hutson

DITCO Contracting Officer

Unless otherwise specified, all other terms and conditions are unchanged.

Paragraph E.SERVICE DATE change from:

Sep 5, 2022

To:

Jul 25, 2022

Paragraph M.3.TSR NUMBER change from:

SG15MAR227235A

SG15MAR227235

Delete the following:

LOCATION OF TERMINATION C:

ADDRESS: 308; 5450 CARLISLE PIKE; MECHANCSBRG, PA, 17050-0975

ROOM: 203; 2 FL

LOCATION: CCI

EXTENSION OF TELECOMMUNICATIONS SERVICE: All facilities between vendor's commercial communications interface point and termination location shall be provided by vendor. All cables shall be run in accordance with local site standards.

INTERFACE: SONET OC-48; OPTICAL; SNAP CLICK

DEMARK: (BLDG) 308; (RM) 203; 2 FL; 5450 CARLISLE PIKE; MECHANCSBRG, PA, 17050-0975

NPA/NXX: 717/790

UNIQUE INSTALLATION FACTORS: A. VENDOR IS RESPONSIBLE FOR INSTALLATION AND MAINTENANCE OF SINGLE

MODE FIBER FROM DROP SIDE OF COMMERCIAL FIBER POINT OF PRESENCE FIBER DISTRIBUTION PANEL (FDP)

BLDG 308, ROOM 203 TO LINE SIDE OF DISA IE1 PROVIDED FIBER TERMINATING PATCH PANEL INSTALLED IN ODXC

SUITE (UODWMEC010) BLDG 308, ROOM 203. TERMINATE WITH "SC" CONNECTORS TO DISA PROVIDED FIBER

TERMINATING PATCH PANEL.

B. VENDOR MUST PROVIDE FIBER STRANDS FROM THEIR POINT OF PRESENCE TO ODXC SUITE WITHOUT

SPLICING AND OR USE OF CONNECTORS TO CONNECT 2 OR MORE FIBER STRANDS MEANING THE FIBER CANNOT

BE BROKEN IN THE MIDDLE AND MUST BE CONTINUOUS.

C. LENGTH OF SINGLE MODE FIBER JUMPERS REQUIRED WILL BE BASED ON LOCATION OF THEIR POINT OF

PRESENCE.

D. CIRCUIT MUST BE TAGGED WITH LOCAL CIRCUIT ID AND LONG HAUL CIRCUIT NO. AS APPLICABLE AT DROP SIDE

OF COMMERCIAL FIBER POINT OF PRESENCE FIBER DISTRIBUTION PANEL (FDP) BLDG 308, ROOM 203.

ADDITIONALLY, VENDOR MUST SHOW SITE PERSONNEL LISTED ON THIS ORDER THE EXACT TERMINATION POINT

WHEN SERVICE IS COMPLETE.

E. VENDOR MUST SCHEDULE/COORDINATE WITH POC'S LISTED ON THIS ORDER 72 HOURS IN ADVANCE PRIOR TO

SITE SURVEYS OR INSTALLATIONS.

INSIDE WIRE INSTALLATION / MAINTENANCE REQUIRED: CPIWI-YES/CPIWM-YES

CONTACT: (PMRY POC) MR. DAN S BRAMBLEY; ISA.MECHANICSBURG.EIS.MBX.CIRCUITS-CKTS @MAIL.MIL;

DANIEL.S.BRAMBLEY.CIV@MAIL.MIL; (CMCL) 717-918-6200; (DSN) 322-918-6200

Delete the following:

LOCATION OF TERMINATION D:

ADDRESS: 308; 5450 CARLISLE PIKE; MECHANCSBRG, PA, 17050-0975

ROOM: 203; 2 FL

LOCATION: BIO

EXTENSION OF TELECOMMUNICATIONS SERVICE: All facilities between vendor's commercial communications interface point and termination location shall be provided by vendor. All cables shall be run in accordance with local site standards.

INTERFACE:

DEMARK:

NPA/NXX: 717/790

UNIQUE INSTALLATION FACTORS:

INSIDE WIRE INSTALLATION / MAINTENANCE REQUIRED:

CONTACT: (PMRY POC) MR. DAN S BRAMBLEY; (UNCLASS ORG) DISA.MECHANICSBURG.EIS.MBX.CIRCUITS-CKTS

@MAIL.MIL; (UNCLASS USER) DANIEL.S.BRAMBLEY.CIV@MAIL.MIL; (CMCL) 717-918-6200; (DSN) 322-918-6200

Location A, DEMARK change from:

(BLDG) 700; RM 104A; 1 FL; 362 OTIS STREET; ROME, NY, 13441-4812

Location A, UNIQUE INSTALLATION FACTORS change from:

A. VENDOR IS RESPONSIBLE FOR INSTALLATION AND MAINTENANCE OF SINGLE MODE FIBER FROM LINE SIDE OF

DISA IE1 PROVIDED FIBER TERMINATING PATCH PANEL INSTALLED IN ODXC SUITE (UODWROM010) BLDG 700, ROOM 104A TO DROP SIDE OF COMMERCIAL FIBER POINT OF PRESENCE FIBER DISTRIBUTION PANEL (FDP) BLDG

700, ROOM ROOM 104A.

B. VENDOR MUST PROVIDE FIBER STRANDS FROM DISA IE1 PROVIDED FIBER PATCH PANEL TO DROP SIDE

OF COMMERCIAL FIBER POINT OF PRESENCE FIBER DISTRIBUTION PANEL (FDP) WITHOUT SPLICING AND OR USE

OF CONNECTORS TO CONNECT 2 OR MORE FIBER STRANDS MEANING THE FIBER CANNOT BE BROKEN IN THE

MIDDLE AND MUST BE CONTINUOUS.

C. CIRCUIT MUST BE TAGGED WITH LOCAL CIRCUIT ID AND LONG HAUL CIRCUIT NO. AS APPLICABLE AT DROP SIDE

OF COMMERCIAL FIBER POINT OF PRESENCE FIBER DISTRIBUTION PANEL (FDP) BLDG 700, ROOM 104A.

ADDITIONALLY, VENDOR MUST SHOW SITE PERSONNEL LISTED ON THIS ORDER THE EXACT TERMINATION POINT

WHEN INSTALLATION IS COMPLETE.

D. VENDOR MUST SCHEDULE/COORDINATE WITH POC'S LISTED ON THIS ORDER 72 HOURS IN ADVANCE PRIOR TO

SITE SURVEYS OR INSTALLATIONS.

Location A, CONTACT change from:

(PMRY POC) MR. DANIEL FOLEY; (UNCLASS USER) DANIEL.FOLEY.6@US.AF.MIL; (CMCL) 315-334-6152; (DSN) 312-

587-6152 (ALT POC) CIRCUIT ACTIONS; (UNCLASS ORG) USAF.NY.224-ADG.LIST.224-SS-SC-CIRCUIT-A

CTIONS@MAIL.MIL; (CMCL) 315-334-6760; (DSN) 587-6760

(PMRY POC) MR. DANIEL FOLEY; DANIEL.FOLEY.6@US.AF.MIL; (CMCL) 315-334-6152; (DSN) 312-587-6152

(ALT POC) CIRCUIT ACTIONS;

USAF.NY.224-ADG.LIST.224-SS-SC-CIRCUIT-A CTIONS@MAIL.MIL; (CMCL) 315-334-6760; (DSN) 587-6760

Location A, INTERFACE change from:

SONET OC-48; OPTICAL; SNAP CLICK (SC)

Location A, INSIDE WIRE INSTALLATION / MAINTENANCE REQUIRED change from:

CPIWI-YES/CPIWM-YES

Location A, TERMINAL EQUIPMENT change from:

ODXC SWITCH (SN 9000 SC INTELLIGENT OPTICAL SWITCH)(GFE) (DISA IE1 PROVIDED) UODWROM010 OPTICAL

INTERFACE CARD (GFE)(DISA IE1 PROVIDED) FIBER TERMINATING PATCH PANEL (GFE)(DISA IE1

PROVIDED)SYCAMORE-SN9000-OPTI-DIGITAL-C-CONNECT

FIBER CABLE X-CONNECT, IN-HOUSE,INSIDE WIRE,SINGLE-MODE, 1310NM, TELCO

Location B, LOCATION OF TERMINATION B change from:

ADDRESS: 700; 362 OTIS STREET; ROME, NY, 13441-4812

ROOM: 104A; 1 FL

LOCATION: ROME

ADDRESS: 308; 5450 CARLISLE PIKE; MECHANCSBRG, PA, 17050-0975

ROOM: 203; 2 FL

LOCATION: NSAMCNCS

Location B, DEMARK change from:

(BLDG) 700; RM 104A; 1 FL; 362 OTIS STREET; ROME, NY, 13441-4812

(BLDG) 308; (RM) 203; 2 FL; 5450 CARLISLE PIKE; MECHANCSBRG, PA, 17050-0975

Location B, UNIQUE INSTALLATION FACTORS change from:

A. VENDOR IS RESPONSIBLE FOR INSTALLATION AND MAINTENANCE OF SINGLE MODE FIBER FROM LINE SIDE OF

DISA IE1 PROVIDED FIBER TERMINATING PATCH PANEL INSTALLED IN ODXC SUITE (UODWROM010) BLDG 700, ROOM 104A TO DROP SIDE OF COMMERCIAL FIBER POINT OF PRESENCE FIBER DISTRIBUTION PANEL (FDP) BLDG

700, ROOM ROOM 104A.

B. VENDOR MUST PROVIDE FIBER STRANDS FROM DISA IE1 PROVIDED FIBER PATCH PANEL TO DROP SIDE

OF COMMERCIAL FIBER POINT OF PRESENCE FIBER DISTRIBUTION PANEL (FDP) WITHOUT SPLICING AND OR USE

OF CONNECTORS TO CONNECT 2 OR MORE FIBER STRANDS MEANING THE FIBER CANNOT BE BROKEN IN THE

MIDDLE AND MUST BE CONTINUOUS.

C. CIRCUIT MUST BE TAGGED WITH LOCAL CIRCUIT ID AND LONG HAUL CIRCUIT NO. AS APPLICABLE AT DROP SIDE

OF COMMERCIAL FIBER POINT OF PRESENCE FIBER DISTRIBUTION PANEL (FDP) BLDG 700, ROOM 104A.

ADDITIONALLY, VENDOR MUST SHOW SITE PERSONNEL LISTED ON THIS ORDER THE EXACT TERMINATION POINT

WHEN INSTALLATION IS COMPLETE.

D. VENDOR MUST SCHEDULE/COORDINATE WITH POC'S LISTED ON THIS ORDER 72 HOURS IN ADVANCE PRIOR TO

SITE SURVEYS OR INSTALLATIONS.

To:

A. VENDOR IS RESPONSIBLE FOR INSTALLATION AND MAINTENANCE OF SINGLE MODE FIBER FROM DROP SIDE OF

COMMERCIAL FIBER POINT OF PRESENCE FIBER DISTRIBUTION PANEL (FDP) BLDG 308, ROOM 203 TO LINE SIDE OF

DISA IE1 PROVIDED FIBER TERMINATING PATCH PANEL INSTALLED IN ODXC SUITE (UODWMEC010) BLDG 308, ROOM 203. TERMINATE WITH "SC" CONNECTORS TO DISA PROVIDED FIBER TERMINATING PATCH PANEL.

B. VENDOR MUST PROVIDE FIBER STRANDS FROM THEIR POINT OF PRESENCE TO ODXC SUITE WITHOUT

SPLICING AND OR USE OF CONNECTORS TO CONNECT 2 OR MORE FIBER STRANDS MEANING THE FIBER CANNOT

BE BROKEN IN THE MIDDLE AND MUST BE CONTINUOUS.

C. LENGTH OF SINGLE MODE FIBER JUMPERS REQUIRED WILL BE BASED ON LOCATION OF THEIR POINT OF

PRESENCE.

D. CIRCUIT MUST BE TAGGED WITH LOCAL CIRCUIT ID AND LONG HAUL CIRCUIT NO. AS APPLICABLE AT DROP SIDE

OF COMMERCIAL FIBER POINT OF PRESENCE FIBER DISTRIBUTION PANEL (FDP) BLDG 308, ROOM 203.

ADDITIONALLY, VENDOR MUST SHOW SITE PERSONNEL LISTED ON THIS ORDER THE EXACT TERMINATION POINT

WHEN SERVICE IS COMPLETE.

E. VENDOR MUST SCHEDULE/COORDINATE WITH POC'S LISTED ON THIS ORDER 72 HOURS IN ADVANCE PRIOR TO

SITE SURVEYS OR INSTALLATIONS.

Location B, CONTACT change from:

(PMRY POC) MR. DANIEL FOLEY; DANIEL.FOLEY.6@US.AF.MIL; (CMCL) 315-334-6152; (DSN) 312-587-6152

(ALT POC) CIRCUIT ACTIONS;

USAF.NY.224-ADG.LIST.224-SS-SC-CIRCUIT-A CTIONS@MAIL.MIL; (CMCL) 315-334-6760; (DSN) 587-6760

To:

(PMRY POC) MR. DAN S BRAMBLEY; ISA.MECHANICSBURG.EIS.MBX.CIRCUITS-CKTS @MAIL.MIL;

DANIEL.S.BRAMBLEY.CIV@MAIL.MIL; (CMCL) 717-918-6200; (DSN) 322-918-6200

Location B, INTERFACE change from:

SONET OC-48; OPTICAL; SNAP CLICK (SC)

SONET OC-48; OPTICAL; SNAP CLICK

Location B, NPA/NXX change from:

315/334

To:

717/790

Location B, COUNTRY CODE change from:

Location B, TERMINAL EQUIPMENT change from:

FIBER CABLE X-CONNECT, IN-HOUSE,INSIDE WIRE,SINGLE-MODE, 1310NM, TELCO

FIBER CABLE X-CONNECT, IN-HOUSE, INSIDE WIRE, SINGLE-MODE, 1310NM, TELCO