HC101320QB269.v0.pdf

IQO INQUIRY

FM: PL8211

TO: Contractors

DATE (MM/DD/YYYY): 10/23/2020

SUBJECT: HC101320QB269

A. TYPE ACTION: START

1. PURPOSE: 1. SUBMIT A QUOTE TO PROVIDE, INSTALL, AND MAINTAIN A 10GB

ETHERNET IQ0 LEASE BETWEEN BLDG 384, RM AT&T, 3490 SENN RD, SAN DIEGO,

CA (SNDGNB/CCI) AND 271, RM B1-238, 400 NORTH DOUGLAS AVE, EL SEGUNDO, CA

(LSAGLAFB/CCI)

2. CONTRACTORS MUST ADDRESS IN QUOTES COMPLIANCE WITH TESTING AND

ACCEPTANCE REQUIREMENTS WITH “UNDERSTAND AND WILL COMPLY”

3. TESTING & ACCEPTANCE REQUIREMENTS MUST BE COORDINATED WITH GOVERNMENT

POC AT BOTH LOCATIONS BEFORE NOTICE OF COMPLETION IS SUBMITTED TO DITCO.

4. CONTRACTORS ARE RESPONSIBLE FOR READING AND ADDRESSING ALL TECHNICAL

REQUIREMENTS OF THIS INQUIRY/SOLICITATION, READING AND AGREEING WITH THE

STANDARD PROVISIONS, PROVIDE PRICE QUOTATION IN ACCORDANCE WITH STANDARD

PROVISION 4, AND MEET THE REQUESTED SERVICE DATE.

5. THE SERVICE DATE TO BE MET IS: 07 MAR 21 (SIP) TO COMPLY WITH PROCUREMENT

ACQUISITION LEAD TIME (PALT) FOR THIS TYPE OF SERVICE.

6. CONTRACTORS MUST CONSIDER ALL ISSUES THAT MAY DELAY THE DELIVERY OF

CIRCUIT ON APPROVED SERVICE DATE. THE GOVERNMENT MAY CANCEL, TERMINATE,

OR REQUEST CONSIDERATION IAW STANDARD PROVISION 42 FOR FAILURE TO MEET

CONTRACTUAL SERVICE.

7. QUOTES MUST INCLUDE NAME AND INFORMATION ABOUT SUB-CONTRACTOR/LONG

HAUL PROVIDER/OTHER CARRIER INSTALLING CIRCUIT IS ON NET/OFF NET, RTD, JUMBO

FRAMING, TESTING AND OTHER APPLICABLE TECHNICAL INFORMATION. FURTHERMORE,

IF A BUILD IS REQUIRED TO INSTALL, VENDOR MUST INDICATE THE SCOPE OF THE BUILD

(LENGTH, BURIED/AERIAL, TRENCHING/DIRECTIONAL BORING, NEW CONDUIT, ETC.)

VENDOR MUST ALSO INDICATE IF SITE POC (S) HAVE ADVISED THAT PERMISSION FOR

BUILD AT SITE (S) WILL BE GRANTED, AND IF SITE (S) HAVE SUFFICIENT SPACE, POWER

AND HVAC CAPACITY TO SUPPORT VENDOR EQUIPMENT AND CABLING. MAPS/BLOCK

DIAGRAMS ARE AN ACCEPTABLE WAY TO PROVIDE THIS INFORMATION.

8. QUOTES MUST BE UPLOADED TO IDEAS. THE GOVERNMENT IS NOT RESPONSIBLE

FOR MISSING OR OVERLOOKED QUOTES. CONTRACTORS ARE INSTRUCTED TO SUBMIT

QUESTIONS AND REQUEST CLARIFICATIONS OF REQUIREMENT (S) BEFORE SUBMITTING

QUOTES. IN RESPONSE TO THIS SOLICITATION, NO TERMS OR CONDITIONS PLACED UPON

THE GOVERNMENT, NOR ASSUMPTIONS WILL BE ACCEPTED.

HC101320QB269

9. THIS REQUIREMENT MUST BE WORKED IN CONJUNCTION WITH SOLICITATION

HC101320QB269 / RU28JUL206715 AND MUST BE ENGINEERED AND PROVISIONED TOTALLY

DIVERSE END TO END FROM THE GOVERNMENT SERVICE DELIVERY POINTS (SDP) FROM

TSR RU28JUL206715; MEANING THE PHYSICAL PATHS ARE TOTALLY SEPARATE INCLUDING

MAN HOLES, CONDUIT, CENTRAL OFFICE LOCATIONS, AND FIBER BUILDS. ADDITIONALLY

AS A MINIMUM MUST HAVE 50 METERS PHYSICAL SEPARATION FROM TSR RU28JUL206715.

10. CONTRACTOR SHALL PROVIDE COLOR POWERPOINT DRAWINGS SHOWING THE

ROUTES FROM THE COMMERCIAL DEMARKS TO THE SUPPORTING CENTRAL OFFICES AND/

OR WIRING CENTERS, ENSURING THE PHYSICAL END TO END DIVERSITY REQUIREMENTS

ARE BEING MET. DRAWINGS MUST INCLUDE SEPARATION DISTANCES, TOTAL FIBER MILES

AND ROUND TRIP DELAY BASED ON ACTUAL DISTANCE IN MILES. REFER TO STANDARD

PROVISION 39 FOR SPECIFIC DOCUMENTATION REQUIREMENTS. SAMPLE DRAWINGS

INCLUDED WITH INQUIRY/SOLICITATION SHALL BE FOLLOWED IN ORDER TO PROVIDE THE

REQUIRED TECHNICAL INFORMATION. MAPS AND DRAWINGS WITH ERRORS, MISMATCH

INFORMATION, MISSING RTD, AND NOT ENOUGH DETAIL TO DETERMINE DIVERSITY

THROUHGOUT THE FIBER PATH WILL BE FOUND TECHNICALLY DEFFICIENT AND WILL NOT

BE ACCEPTED.

11. PRE AWARD SITE SURVEYS ARE AUTHORIZED (AT CONTRACTOR EXPENSE) AND

SHOULD BE CONDUCTED IN COORDINATION WITH LOCAL POCS AT EACH GOVERNMENT

SITE.

12. AWARDS OF DIVERSE REQUIREMENTS WILL ONLY BE SPLIT BETWEEN TWO

CONTRACTORS IF THE DIVERSITY, RTD, SERVICE DATE AND LOWEST PRICE

REQUIREMENTS ARE PRESERVED.

13. ESTABLISH TSP:

14. LINE MUST REMAIN FULLY OPERATIONAL AND AVAILABLE TO USERS 24 HOURS A

DAY, SEVEN DAYS PER WEEK, MONTHLY PERFORMANCE OF 99.5% AVAILABILITY OR

BETTER. (H) 1 HOUR RESPONSE TIME TO RESPOND TO CUSTOMER UPON RECEIPT

OF TROUBLE. (I) VENDOR REQUIRED TO HAVE CIRCUIT VISIBILITY TO ASSIST IN ANY

CIRCUIT OUTAGES. (J) VENDOR MUST HAVE A 24X7 NETWORK OPERATIONS CENTER. (K)

TELECOM PROVIDER MUST MAINTAIN OPERATIONS, MAINTENANCE AND ADMINISTRATION

MONITORING OF ETHERNET CIRCUIT. M. THIS TSO IS IN SUPPORT OF EXERCISE/PROJECT:

MPLS IMPLEMENTATIONS N. FACILITY SECURITY ACCESS REQUIREMENT: (SP B) ESCORT

REQUIRED; THE TELECOM PROVIDER MUST PROVIDE DITCO COLOR POWERPOINT

DRAWINGS FOR TECHNICAL REVIEW SHOWING THE ROUTES FROM THE COMMERCIAL

DEMARCS TO THE SUPPORTING CENTRAL OFFICES AND/OR WIRING CENTERS. DRAWINGS

MUST INCLUDE SEPARATION DISTANCES BETWEEN DIVERSE REQUIREMENTS, TOTAL

FIBER MILES AND ROUND TRIP DELAY, AND FIBER ROUTES RED LINED END TO END SO

THE GOVERNMENT CAN CONFIRM PHYSICAL END TO END DIVERSITY REQUIREMENTS

ARE MET. ADDITIONALLY, THE VENDOR IS TO PROVIDE DITCO WITH DETAILED CIRCUIT/

PATH CONNECTIVITY DIAGRAMS, IN KMZ OR KML FORMAT, IDENTIFYING ALL POINTS

OF PRESENCE FOR EVALUATION AND AS A FINAL RECORD OF THE INSTALLED PATH.

THESE DIAGRAMS MUST BE PROVIDED TO DISA HQ IE16 (DISA.MEADE.IE.MBX.IE16-

PROVISIO NING-TEAM@MAIL.MIL) FOR HISTORICAL PURPOSES. 6. THE VENDOR MUST

PROVIDE LIGHT LEVEL READINGS (SIGNAL STRENGTH IN DBM) ON THE EXTENSION FROM

COMMERCIAL POP TO THE GOVERNMENT SERVICE DELIVERY POINT (SDP) AT THE "A"

AND "Z" LOCATION PRIOR TO CIRCUIT TURN OVER TO THE GOVERNMENT ENSURING

LEVELS ARE WITHIN SPECS. LIGHT LEVELS MUST BE ADJUSTED TO -3 TO -9 DBM. 7. THE

VENDOR MUST TERMINATE 10GB ETHERNET SERVICE AT SERVICE DELIVERY LOCATIONS,

IAW UNIQUE INSTALLATION FACTORS. 8. THE VENDOR MUST CONDUCT WALK-THROUGH

SITE SURVEY PRIOR TO INSTALLATION AT BOTH LOCATIONS. 9. THE VENDOR MUST

CONTACT DISA GOC IP BACKBONE ENGINEERING AND IMPLEMENTATION GROUP UPON

RECEIPT OF A VALID TSO TO ESTABLISH THE COORDINATION AND ACTIVATION PROCESS.

PHONE :( C) 618-418-8627, (D) 418-8627. 10. THE VENDOR MUST CONTACT DISA GOC TIER-II

ENGINEERING 48 HOURS PRIOR TO BEGINNING THEIR END-TO-END TESTING. PHONE :( C)

618-418-8627, (D) 418-8627. P. REMARKS CONTINUED: 11. THE PROVIDER MUST CONDUCT

A SATISFACTORY 24-HOUR TEST FROM THE DROP SIDE OF THEIR OR LOCAL EXCHANGE

CARRIERS FDP INSTALLED IN THEIR EQUIPMENT SUITE AT THE "A" LOCATION TO THEIR

OR LOCAL EXCHANGE CARRIERS FDP INSTALLED IN THEIR EQUIPMENT SUITE AT THE "Z"

LOCATION AND MUST INCLUDE THE EXTENSION BETWEEN THE COMMERCIAL DEMARC

AND THE GOVERNMENT'S SDP. VENDOR MUST ENSURE TEST SETS ARE PLACED AT

THE DROP SIDE AT THE "A" LOCATION AND AT THE "Z" LOCATION. TESTING MUST BE

SATISFACTORY PRIOR TO TURN OVER TO THE GOVERNMENT FOR ACCEPTANCE TESTING.

THE VENDOR MUST TEST THE CIRCUIT FOR 24 HOURS IAW THE FULL ITU-T.Y.1564 BENCH

MARKING METHODOLOGY FOR NETWORK INTERCONNECT DEVICES STANDARD, AND

AT THE COMMITTED INFORMATION RATE (CIR) IAW ITU-T-Y.1564. REMARKS: 1. CIRCUIT

REQUIRES THE FOLLOWING PARAMETERS: (A) FIBER TERMINATION: FRAME FORMAT:

10GB ETHERNET (OPTICAL HANDOFF-10GB ETHERNET-LAN-PHY-SINGLE MODE FIBER),

1310NM. "SC" OR "LC" CONNECTORS AS DETERMINED BY SITE SURVEY. NOTE: WHEN

EXTENDED REACH OPTICS ARE USED THAT CHANGE THE TX/RX WAVELENGTH OF THE

OPTIC, THE VENDOR WILL NOTIFY THE GOVERNMENT 30 DAYS PRIOR TO DELIVERY.

(B) COMMITTED INFORMATION RATE (CIR): 10GB. (C) ETHERNET FRAME SIZE WILL BE

CONFIGURED TO SUPPORT MAXIMUM TRANSMISSION UNIT (MTU) OF 9000 OCTETS

(BYTES) JUMBO FRAMES. (D) NO NETWORK INTERFACE UNIT, DEDICATED PATH. (E) GFE

CLOCKING: VENDOR ESFU (OR EQUIVALENT) NOT TO BE ENGINEERED INTO CIRCUIT.

(F) TESTING CRITERIA: VENDOR MUST TEST THE CIRCUIT FOR 24 HOURS IAW THE FULL

ITU-T.Y.1564 BENCH MARKING METHODOLOGY FOR NETWORK INTERCONNECT DEVICES

STANDARD, AND AT THE COMMITTED INFORMATION RATE (CIR) IAW ITU-T-Y.1564. NOTE:

ETHERNET FRAME SIZE DESIGNATOR 'H' (MTU) IS EQUAL TO 9000 BYTES. Q. REMARKS

CONTINUED: (G) LINE MUST REMAIN FULLY OPERATIONAL AND AVAILABLE TO USERS 24

HOURS A DAY, SEVEN DAYS PER WEEK, MONTHLY PERFORMANCE OF 99.5% AVAILABILITY

OR BETTER. (H) 1 HOUR RESPONSE TIME TO RESPOND TO CUSTOMER UPON RECEIPT

OF TROUBLE. (I) VENDOR REQUIRED TO HAVE CIRCUIT VISIBILITY TO ASSIST IN ANY

CIRCUIT OUTAGES. (J) VENDOR MUST HAVE A 24X7 NETWORK OPERATIONS CENTER. (K)

TELECOM PROVIDER MUST MAINTAIN OPERATIONS, MAINTENANCE AND ADMINISTRATION

MONITORING OF ETHERNET CIRCUIT. (L) THE COMMERCIAL CIRCUIT WILL BE ACCEPTED

ON BEHALF OF THE GOVERNMENT BY THE DISA GOC IP BACKBONE ENGINEERING AND

IMPLEMENTATION GROUP, SCOTT AFB, IL. (C) 618-418-8627, (D) 418-8627. 2. VENDOR

WINNING AWARD IS RESPONSIBLE FOR INSTALLATION AND MAINTENANCE OF THE

SERVICE IAW THE UNIQUE INSTALLATION FACTORS. 3. INSIDE WIRING IS AUTHORIZED

IAW THE UNIQUE INSTALLATION FACTORS. 4. VENDOR MUST COORDINATE SITE VISIT

WITH POC'S 72 HOURS IN ADVANCE PRIOR TO REQUIRING ACCESS TO FACILITIES AT

BOTH USER LOCATIONS. 5. VENDOR MUST CONTACT DISA GOC TIER-II ENGINEERING

48 HOURS PRIOR TO BEGINNING THEIR END-TO-END TESTING. 6. ALL EQUIPMENT AND

CIRCUIT PROBLEMS WILL BE REPORTED BY PHONE TO THE DISA GOC IP BACKBONE

ENGINEERING AND IMPLEMENTATION GROUP, SCOTT AFB, IL. PRIMARY: (C) 618-418-9950,

(D) 418-9950 TOLL FREE: 855-868-9950. 7. DD FORM 1368 WILL BE SUBMITTED ON THIS

TRUNK IAW DISAC-DITCO 350-135-1 BY RNSOC, SCOTT AFB, IL. GUIDANCE ON SUBMISSION

IS AVAILABLE AT . CLICK ON "DISA-DITCO CIRCULAR, 350-135-1, DEFENSE COMMERCIAL

COMMUNICATIONS ACQUISITION PROCEDURES." R. REMARKS CONTINUED: (L) THE

COMMERCIAL CIRCUIT WILL BE ACCEPTED ON BEHALF OF THE GOVERNMENT BY THE

DISA GOC IP BACKBONE ENGINEERING AND IMPLEMENTATION GROUP, SCOTT AFB,

IL. (C) 618-418-8627, (D) 418-8627. 2. VENDOR WINNING AWARD IS RESPONSIBLE FOR

INSTALLATION AND MAINTENANCE OF THE SERVICE IAW THE UNIQUE INSTALLATION

FACTORS. 3. INSIDE WIRING IS AUTHORIZED IAW THE UNIQUE INSTALLATION FACTORS.

4. VENDOR MUST COORDINATE SITE VISIT WITH POC'S 72 HOURS IN ADVANCE PRIOR

TO REQUIRING ACCESS TO FACILITIES AT BOTH USER LOCATIONS. 5. VENDOR MUST

CONTACT DISA GOC TIER-II ENGINEERING 48 HOURS PRIOR TO BEGINNING THEIR END-TO-

END TESTING. 6. ALL EQUIPMENT AND CIRCUIT PROBLEMS WILL BE REPORTED BY PHONE

TO THE DISA GOC IP BACKBONE ENGINEERING AND IMPLEMENTATION GROUP, SCOTT

AFB, IL. PRIMARY: (C) 618-418-9950, (D) 418-9950 TOLL FREE: 855-868-9950.

MINIMUM TECHNICAL SPECIFICATIONS: SPECIFIC FORMAT TO BE USED IS: LINE RATE:

10.3125 GIGABITS/S, +- 100 PPM LINE CODE: OPTICAL 1. TEST AND ACCEPTANCE: THIS

CIRCUIT SHALL PASS A FULLY DOCUMENTED, SATISFACTORY, 72 HOUR SOAK TEST

BY DISA GOC AT SCOTT AFB, IL. PRIMARY: (C) 618-418-8627 (D) 418-8627. 2. ERROR

PERFORMANCE: ERROR PERFORMANCE SHALL BE BETTER THAN THE FOLLOWING

PARAMETER THRESHOLDS TO BE ACCEPTABLE: AVAILABILITY SHALL BE GREATER THAN

99.5% OR BETTER. FRAME LOSS SHALL BE EQUAL TO ZERO WHEN TESTING AT 10 GIGABIT

HIGHEST FRAME RATE, AND SHALL MEET ITU-T-Y.1564 STANDARDS. JITTER SHALL BE

LESS THAN 3 MSEC. DELAY SHALL BE BETTER THAN 10 MSEC. 3. MEAN TIME TO LOSS

OF BIT COUNT INTEGRITY (MTTLBCI) SHALL S. REMARKS CONTINUED: BE GREATER

THAN 24 HOURS. 4. ROUND TRIP DELAY (RTD) FOR THIS DISA TRANSPORT TRUNK WILL

BE MEASURED IN MILLISECONDS FROM THE CUSTOMER'S SERVICE DELIVERY POINT

(SDP) SITE-A TO THE CUSTOMER'S SERVICE DELIVERY POINT (SDP) SITE-Z. THE RTD

SHALL BE LESS THAN OR EQUAL TO 10 MILLISECONDS TO EFFECTIVELY SUPPORT THE

GOVERNMENT'S MISSION. THE GOVERNMENT ACCEPTING AUTHORITY WILL CONFIRM

THE RTD DURING THE TURN-UP AND TEST PHASE AND IF IT DOES NOT ALIGN WITH THE

CONTRACTORS PROPOSAL, DISA IE161 WILL NOTIFY DITCO IMMEDIATELY IN WRITING.

(**UNIQ INSTALL FACTORS**) (SP A) TERMINATING PATCH PANEL BLDG 3409, ROOM TELCO

TO THE LINE SIDE OF THE SITE PROVIDED FIBER TERMINATING PATCH PANEL BLDG

384, ROOM AT&T, USING EXISTING ON-BASE SINGLE-MODE FIBER. (** DIVERSITY INFO

**) NETWORK DIVERSITY REQUIRED: PATH DIVERSITY; COMMERCIAL DIVERSITY: NO;

DIVERSITY FROM CJON:SF24JUL205552 (** ADDITIONAL PROVISIONING INFORMATION

**) (ORG ACCT) DISA (DISN IP ROUTER NETWORK BACKBONE AND BACKBONE HOSTS)

(CONUS AND OCONUS) T. REMARKS CONTINUED: FUNDING TCO APL: ON BEHALF OF

DEFENSE INFORMATION SYSTEMS AGENCY FUNDING APPROVAL: THIS REQUIREMENT

IS A BONA FIDE NEED OF FY20 AND DISA FY20 FUNDING INFORMATION IS AVAILABLE

IN DISA'S TELECOMMUNICATIONS INVENTORY AND BILLING INFORMATION (TIBI)

APPLICATION. U. JUSTIFICATION OF SERVICE REQUESTED: THIS ACTION SUPPORTS

DISN IP BACKBONE IMPLEMENTATION. V. SATELLITE OBJECTION: DIVERSITY: DISA

MANDATED; W. COMPLETION REPORT: (1) STATION DESIGNATED IN PARAGRAPH 2H

AS CCO/CMO WILL SUBMIT COMPLETION REPORT IAW DISAC 310-130-1, SUPP 1, 2, 3

FORMAT OR DISAC 310-70-1. REPORT WILL BE ADDRESSED TO ORIGINATOR AND ALL

ADDRESSEES OF THIS (TSO). (2) STATIONS IN PARA 3 OF THIS (TSO) ARE RESPONSIBLE

FOR VERIFYING IN-STATION DETAILS AND FORWARDING THE CORRECT INFORMATION,

IF ANY DISCREPANCIES ARE NOTED, TO THE CCO/CMO DESIGNATED IN PARA 2H.

THE CCO/CMO WILL SUBMIT CORRECTIONS TO DISA VIA "EXCEPTION REPORT" IAW

DISAC 310-130-1, CHAP 2. X. CIRCUIT SPECIFICATIONS: CONUS NO JUMBO FRAME

ETHERNET VENDOR WILL PERFORM ACCEPTANCE TESTING IN ACCORDANCE WITH

EITHER RFC-6815 OR ITU-T Y.1564. VENDOR MUST TEST THE CIRCUIT FOR 24 HOURS

IAW ITU-T.Y.1564 SPECIFICALLY, FRAME SIZES OF 64,128,256,512,1024,1280 AND 1518

BYTES MUST BE USED. THE TEST MUST VERIFY LENGTH OF RECEIVED FRAMES, INDICATE

NUMBER OF FRAMES DROPPED, NUMBER OF FRAMES RECEIVED OUT OF ORDER, AND

DUPLICATE FRAMES. TESTS MUST BE BI-DIRECTIONAL USING THE SAME DATA RATE

IN EACH DIRECTION. BURST TESTS MUST BE RUN TO DETERMINE MINIMUM INTERVAL

BETWEEN FRAMES THAT CAN BE PROCESSED WITHOUT FRAME LOSS. A THROUGHPUT

TEST IS REQUIRED INDICATING THE FASTEST RATE AT WHICH TEST FRAMES CAN BE

TRANSMITTED WITHOUT FRAME LOSS. A SEPARATE THROUGHPUT TEST MUST BE RUN

WITH FRAMES ADDRESSED TO THE HARDWARE BROADCAST ADDRESS CONSTITUTING

AT LEAST 1% OF THE TEST STREAM AND BE EVENLY DISTRIBUTED THROUGHOUT THE

TEST. Y. CIRCUIT SPECIFICATIONS CONTINUED: A LATENCY TEST MUST BE RUN FOR

A PERIOD OF NO LESS THAN 120 SECONDS, AND REPEATED NO LESS THAT 20 TIMES.

THE TEST STREAM FOR THE LATENCY TEST SHOULD BE RUN AT THE THROUGHPUT

RATE FOR CORRESPONDING FRAME SIZES FROM THE THROUGHPUT TEST. END TO END

LATENCY WILL BE CALCULATED AS THE AVERAGE OVER THE 20 TEST RUNS. FRAME

LOSS RATE TESTS SHOULD BE RUN AT THE FRAME RATE CORRESPONDING TO THE

MAXIMUM FRAME RATE, AND REDUCED BY 10% INTERVALS UNTIL THERE ARE AT LEAST

TWO CONSECUTIVE RUNS IN WHICH NO FRAMES ARE LOST.THROUGHPUT TEST RESULTS:

PASSING RATE 100% FOR ALL FRAME BYTE SIZES EXERCISED. FRAME LOSS RATE (%)

RESULTS: FRAME LOSS RATE LESS THAN 0.01% FOR ALL FRAME BYTE SIZES EXERCISED.

LATENCY WILL BE MEASURED WILL BE ACCORDING TO THE FOLLOWING MAXIMUM

TRANSMISSION DELAY FOR ANY CIRCUIT UP TO 500 MILES AIR-MILES IN LENGTH SHALL

BE NO GREATER THAN 13MS ONE-WAY AND ANY POINT-TO-POINT CIRCUIT LONGER

THAN 500 AIR-MILES SHALL BE NO GREATER THAN 50MS ONE WAY WITHIN THE 48

CONTINENTAL STATES. ANY APS SWITCHOVER SHALL TAKE LESS THAN 50 MILLISECONDS

MONTHLY AVAILABILITY SHALL BE NO LESS THAN 99.5%. Z. IMPLEMENTATION ASSISTANCE:

IMPLEMENTATION ASSISTANCE: FOR SERVICE ACTIVATION INQUIRIES/SCHEDULING/

ASSISTANCE, NAVIGATE TO THE DISA GLOBAL SERVICE ACTIVATIONS CUSTOMER

ACCESS PORTAL: HTTPS://DISA.DEPS.MIL/DISA/COP/GSM-O/BACKBONE/CUSTOMER

%20ACCESS%2 0SITE/SITEPAGES/SAM%20CUSTOMER%20HOMEPAGE.ASPX, OR

CONTACT DSN 312-418-8627, CMCL 001-618-418-8627. FOR EMAIL SUPPORT, PLEASE

CONTACT THE APPROPRIATE TEAM BELOW: DEDICATED/NIPRNET/SIPRNET/VPN SERVICE

ACTIVATIONS: EMAIL: DISA.SCOTT.GLOBAL.MBX.RF-CIRCUIT-ACTIVATIONS@MAIL.MIL

SIPRNET ACCESS MIGRATION (SAM) PROJECTS (D508, D710, D806, D910): EMAIL:

DISA.SCOTT.GLOBAL.MBX.IMPACT-TEAM@MAIL.MIL FOR ALL OTHER PROJECT RELATED

EFFORTS: EMAIL:DISA.SCOTT.GLOBAL.MBX.RF-CIRCUIT-ACTIVATIONS@MAIL.MIL DISN

BACKBONE ACTIVATIONS: EMAIL: DISA.SCOTT.GLOBAL.MBX.CASA-INFRASTRUCTURE-

INTEGRATION-LEAS E-BB-T@MAIL.MIL AA. IMPLEMENTATION ASSISTANCE CONTINUED:

FOR CIRCUIT INSTALLATION ASSISTANCE WITH THE COMMERCIAL LEASED PATH,

CONTACT DCP COMMERCIAL ACTIVATION TEAM (CAT) AT D312-850-0820, C614-692-0820. AB.

UNSATISFACTORY SERVICE REPORTING INSTRUCTIONS: FOR UNSATISFACTORY SERVICE

OR TO REPORT EQUIPMENT AND/OR CIRCUIT PROBLEMS INVOLVING DISA PROVIDED

TRANSPORT AND/OR EQUIPMENT, PLEASE CONTACT THE DISN CUSTOMER CONTACT

CENTER (DCCC) TOLL FREE NUMBER IS 1-844-347-2457 (1-844-DISA HLP) OPTION 2, COML

1-614-692-0032 OPTION 2, DSN 312-850-0032 OPTION 2.

If there are more than two locations, their information will be found in Attachment B to this Order.

B. ALLA NUMBER:

C. TSP AUTHORIZATION CODE/RESTORATION CODE: TSP0KNRU4-01

D. DEMANDER'S CODE:

E. SERVICE DATE (MM/DD/YYYY): 3/7/2021

F. TYPE OF CIRCUIT:

1. BANDWIDTH/DATA RATE: 10 Gigabit

2. SIGNALING MODE: No Signaling

G. LOCATION OF TERMINATION A:

1. ADDRESS: 384; 3490 SENN ROAD; SAN DIEGO, CA, 92136

2. ROOM: AT&T; 1 FL

H. LOCAL PART A:

1. EXTENSION OF TELECOMMUNICATIONS SERVICE: All facilities between vendor's commercial communications interface point and termination location shall be provided by vendor. All cables shall be run in accordance with local site standards.

2. INTERFACE: 10GBASE-LR; PHYSICAL: SC

3. DEMARK: BLDG 384, RM AT&T, 3490 SENN RD, SAN DIEGO, CA (PMRY POC) MR.

STANLEY E PIKES; (CMCL) 619-545-8687 (DSN) 735-8687

4. NPA/NXX: 619/556

5. UNIQUE INSTALLATION FACTORS: 1) FIBER CABLE X-CONNECT, IN-HOUSE, INSIDE

WIRE,

SINGLE-MODE, TELCO.

(2) TELCO MULTIPLEX (COMMERCIAL FIBER POINT OF PRESENCE)

COMMERCIAL CARRIER SYSTEM (LOCAL EXCHANGE CARRIER)

AMPLIFYING INFO:

A. VENDOR IS RESPONSIBLE FOR INSTALLATION AND MAINTENANCE

OF THE SERVICE FROM THE LINE SIDE OF THE DISA IE1 PROVIDED

FIBER TERMINATING PATCH PANEL INSTALLED IN THE CISCO 9006 ROUTER SUITE

(UJEWSDN030) BLDG 384, ROOM SWITCH TO THE DROP SIDE OF THE COMMERCIAL FIBER

POINT OF PRESENCE FIBER DISTRIBUTION PANEL BLDG 384, ROOM AT&T USING SINGLE

MODE FIBER. COORDINATE TYPE CONNECTORS TO BE USED FOR TERMINATION TO THE

DISA PROVIDED PATCH PANEL.

B. VENDOR MUST COORDINATE WITH GOVERNMENT SITE PERSONNEL TO CONDUCT

WALK THROUGH SITE SURVEYS FOR EXACT CABLE FT. FROM THE DISA PROVIDED FIBER

TERMINATING PATCH PANEL INSTALLED IN THE CISCO 9006 ROUTER SUITE BLDG 384,

ROOM SWITCH TO THE COMMERCIAL FIBER POINT OF PRESENCE BLDG 384, ROOM AT&T.

C. VENDOR MUST PROVIDE FIBER STRANDS FROM THE DISA PROVIDED

FIBER PATCH PANEL INSTALLED IN THE CISCO 9006 ROUTER TO THE

COMMERCIAL DEMARC LOCATION WITHOUT SPLICING AND OR USE OF

CONNECTORS TO CONNECT 2 OR MORE FIBER STRANDS MEANING THE FIBER CANNOT BE

BROKEN IN THE MIDDLE AND MUST BE

CONTINUOUS.

D. VENDOR MUST SCHEDULE/COORDINATE WITH THE POC'S LISTED ON THIS ORDER 72

HOURS IN ADVANCE PRIOR TO SITE SURVEYS OR

INSTALLATIONS.

6. INSIDE WIRE INSTALLATION/MAINTENANCE REQUIRED: CPIWI-YES/CPIWM-YES

7. CONTACT: (PMRY POC) MR. STANLEY E PIKES NCTSSD_SDNI_N3_DISA@NAVY.MIL

STANLEY.PIKES@NAVY.MIL (CMCL) 619-767-7643 (DSN) 577-7643

(ALT POC) MR. MAVERICK C FARINAS NCTSSD_SDNI_N3_DISA@NAVY.MIL

MAVERICK.FARINAS@NAVY.MIL (CMCL) 619-545-8687 (DSN) 735-8687

I. TERMINATION EQUIPMENT A: CISCO ASR-9006 ROUTER (GFE)(DISA IE1

PROVIDED)COMMERCIAL FIBER POINT OF PRESENCE

J. LOCATION OF TERMINATION B:

1. ADDRESS: 271; 400 NORTH DOUGLAS; EL SEGUNDO, CA, 90245

2. ROOM: B1-238; B FL

K. LOCAL PART B:

1. EXTENSION OF TELECOMMUNICATIONS SERVICE: All facilities between vendor's commercial communications interface point and termination location shall be provided by vendor. All cables shall be run in accordance with local site standards.

2. INTERFACE: 10GBASE-LR; PHYSICAL: SC

3. DEMARK: 271, RM B1-238, 400 NORTH DOUGLAS AVE, EL SEGUNDO, CA

(PMRY POC) MR. TODD M BARTON ; (CMCL) 310-653-3313 (DSN) 633-3313

4. NPA/NXX:310/653

5. UNIQUE INSTALLATION FACTORS: 1) COMMERCIAL FIBER POINT OF PRESENCE

(2) FIBER CABLE X-CONNECT, IN-HOUSE, INSIDE WIRE, SINGLE-MODE, 1310NM, TELCO

AMPLIFYING INFO:

A. VENDOR IS RESPONSIBLE FOR INSTALLATION AND MAINTENANCE

OF SINGLE MODE FIBER FROM THE DROP SIDE OF COMMERCIAL FIBER

POINT OF PRESENCE FIBER DISTRIBUTION PANEL BLDG 271, RM

B1-238 TO LINE SIDE OF DISA IE1 PROVIDED FIBER TERMINATING

PATCH PANEL INSTALLED IN CISCO ASR-9006 ROUTER SUITE

(UJEWLOA030) BLDG 271, RM B1-239. TERMINATE WITH "SC"

CONNECTORS TO DISA PROVIDED FIBER TERMINATING PATCH PANEL.

B. VENDOR MUST PROVIDE FIBER STRANDS FROM THE DISA PROVIDED

FIBER PATCH PANEL TO THE DROP SIDE OF THEIR POP/FIBER

DISTRIBUTION PANEL WITHOUT SPLICING AND OR USE OF CONNECTORS TO CONNECT 2

OR MORE FIBER STRANDS MEANING THE FIBER CANNOT BE BROKEN IN THE MIDDLE AND

MUST BE CONTINUOUS.

C. CIRCUIT MUST BE TAGGED WITH VENDOR'S LONG HAUL CIRCUIT

ID AND LOCAL EXCHANGE CARRIER CIRCUIT NO. AS APPLICABLE AT DROP SIDE OF THEIR

POINT OF PRESENCE (FIBER DISTRIBUTION PANEL) BLDG 271, RM B1-238. ADDITIONALLY,

VENDOR MUST SHOW SITE PERSONNEL LISTED ON THIS ORDER THE EXACT TERMINATION

POINT WHEN CIRCUIT INSTALLATION IS COMPLETE.

D. VENDOR MUST SCHEDULE/COORDINATE WITH POC'S LISTED ON

THIS ORDER 72 HOURS IN ADVANCE PRIOR TO SITE SURVEYS OR

INSTALLATIONS.

6. INSIDE WIRE INSTALLATION/MAINTENANCE REQUIRED: CPIWI-YES/CPIWM-YES

7. CONTACT: (PMRY POC) MR. TODD M BARTON SMC.TSR.TSO@LOSANGELES.AF.MIL

TODD.BARTON.1@US.AF.MIL (CMCL) 310-653-3313 (DSN) 633-3313

L. TERMINATION EQUIPMENT B: EQUIPMENT INFORMATION: COMMERCIAL FIBER POINT OF

PRESENCE

M. ADDITIONAL INFORMATION:

1. DITCO CSA NUMBER:

2. BASIC AGREEMENT NUMBER: TBD

3. TSR NUMBER: RU28JUL206712

4. CCSD: DIR3B5F1

5. DIVERSITY REQUIREMENTS: YES

6. LOCATIONS TO BE AVOIDED: N/A

7. TRANSMISSION MEDIA TO BE AVOIDED: N/A

8. NETWORKS TO BE AVOIDED: N/A

9. CIRCUIT PARAMETERS: SEE TESTING REQUIREMENTS

10. TESTING REQUIREMENTS: CONUS NO JUMBO FRAME ETHERNET VENDOR WILL

PERFORM ACCEPTANCE TESTING IN ACCORDANCE WITH EITHER RFC-6815 OR ITU-T

Y.1564. VENDOR MUST TEST THE CIRCUIT FOR 24 HOURS IAW ITU-T.Y.1564 SPECIFICALLY,

FRAME SIZES OF 64,128,256,512,1024,1280 AND 1518 BYTES MUST BE USED. THE TEST

MUST VERIFY LENGTH OF RECEIVED FRAMES, INDICATE NUMBER OF FRAMES DROPPED,

NUMBER OF FRAMES RECEIVED OUT OF ORDER, AND DUPLICATE FRAMES. TESTS MUST

BE BI-DIRECTIONAL USING THE SAME DATA RATE IN EACH DIRECTION. BURST TESTS MUST

BE RUN TO DETERMINE MINIMUM INTERVAL BETWEEN FRAMES THAT CAN BE PROCESSED

WITHOUT FRAME LOSS.A THROUGHPUT TEST IS REQUIRED INDICATING THE FASTEST

RATE AT WHICH TEST FRAMES CAN BE TRANSMITTED WITHOUT FRAME LOSS. A SEPARATE

THROUGHPUT TEST MUST BE RUN WITH FRAMES ADDRESSED TO THE HARDWARE

BROADCAST ADDRESS CONSTITUTING AT LEAST 1% OF THE TEST STREAM AND BE

EVENLY DISTRIBUTED THROUGHOUT THE TEST. A LATENCY TEST MUST BE RUN FOR A

PERIOD OF NO LESS THAN 120 SECONDS, AND REPEATED NO LESS THAT 20 TIMES. THE

TEST STREAM FOR THE LATENCY TEST SHOULD BE RUN AT THE THROUGHPUT RATE FOR

CORRESPONDING FRAME SIZES FROM THE THROUGHPUT TEST. END TO END LATENCY

WILL BE CALCULATED AS THE AVERAGE OVER THE 20 TEST RUNS. FRAME LOSS RATE

TESTS SHOULD BE RUN AT THE FRAME RATE CORRESPONDING TO THE MAXIMUM FRAME

RATE, AND REDUCED BY 10% INTERVALS UNTIL THERE ARE AT LEAST TWO CONSECUTIVE

RUNS IN WHICH NO FRAMES ARE LOST. THROUGHPUT TEST RESULTS: PASSING RATE

100% FOR ALL FRAME BYTE SIZES EXERCISED. FRAME LOSS RATE (%) RESULTS: FRAME

LOSS RATE LESS THAN 0.01% FOR ALL FRAME BYTE SIZES EXERCISED. LATENCY WILL BE

MEASURED WILL BE ACCORDING TO THE FOLLOWING MAXIMUM TRANSMISSION DELAY

FOR ANY CIRCUIT UP TO 500 MILES AIR-MILES IN LENGTH SHALL BE NO GREATER THAN

13MS ONE-WAY AND ANY POINT-TO-POINT CIRCUIT LONGER THAN 500 AIR-MILES SHALL

BE NO GREATER THAN 50MS ONE WAY WITHIN THE 48 CONTINENTAL STATES. ANY APS

SWITCHOVER SHALL TAKE LESS THAN 50 MILLISECONDS MONTHLY AVAILABILITY SHALL

BE NO LESS THAN 99.5%.

11. GOVERNMENT ACCEPTANCE ACTIVITY: DISA GOC IP B/D312-770-8627,C618-220-8627

12. SECURITY/ REQUIREMENTS: ESCORT REQUIRED. SECURITY CLEARANCE NOT

REQUIRED. VENDOR MUST CONTACT SITE POC AT LEAST 72 HOURS PRIOR TO ANY SITE

VISIT OR INSTALLATION.

13. SITE ACCESS REQUIREMENTS: ESCORT REQUIRED. SECURITY CLEARANCE NOT

REQUIRED. VENDOR MUST CONTACT SITE POC AT LEAST 72 HOURS PRIOR TO ANY SITE

VISIT OR INSTALLATION.

14. DITCO STANDARD PROVISIONS: Incorporated in full text below

V. QUOTE DUE DATE AND TIME (MM/DD/YYYY): 11/23/2020 4:00 PM America/Chicago

Z. DITCO CONTACT:

Benjamin Sparlin

618-418-6836 benjamin.r.sparlin.civ@mail.mil

Robert E Spencer

DITCO Contracting Officer

618-418-6181 robert.e.spencer.civ@mail.mil

Section G - Contract Administration Data

Included Clauses

G1 - Points of Contact - JUL 2018 Contracting Officer

Name: ANGELINA HUTSON

Organization/Office Symbol: Phone No.: DISA / DITCO

E-Mail Address: ANGELINA.HUTSON.CIV@MAIL.MIL

Contract Specialist

Name: BEN SPARLIN

Organization/Office Symbol: Phone No.: DISA / DITCO

E-Mail Address: BENJAMIN.R.SPARLIN.CIV@MAIL.MIL

COR/Mission Partner Point of Contact (Note: To be filled in upon contract award) Name:

Organization/Office Symbol: Phone No.:

E-Mail Address:

Contractor Point of Contact Contractor Legal Business Name: DUNS:

CAGE CODE: Contractor POC: E-Mail Address: Phone Number: Fax Number:

(End of text)

Standard Provisions

252.239-7016 - Telecommunications Security Equipment, Devices, Techniques, and

Services - DEC 1991

(a) Definitions. As used in this clause--

(1) "Securing" means the application of Government-approved telecommunications security equipment, devices, techniques, or services to contractor telecommunications systems.

(2) "Sensitive information" means any information the loss, misuse, or modification of which, or unauthorized access to, could adversely affect the national interest or the conduct of Federal programs, or the privacy to which individuals are entitled under 5

U.S.C. 552a (the Privacy Act), but which has not been specifically authorized under criteria established by an Executive Order or

Act of Congress to be kept secret in the interest of national defense or foreign policy.

(3) "Telecommunications systems" means voice, record, and data communications, including management information systems and local data networks that connect to external transmission media, when employed by Government agencies, contractors, and subcontractors to transmit--

(i) Classified or sensitive information;

(ii) Matters involving intelligence activities, cryptologic activities related to national security, the command and control of military forces, or equipment that is an integral part of a weapon or weapons system; or

(iii) Matters critical to the direct fulfillment of military or intelligence missions.

(b) This solicitation/contract identifies classified or sensitive information that requires securing during telecommunications and requires the Contractor to secure telecommunications systems. The Contractor agrees to secure information and systems at the following location: (Identify the location.)

(c) To provide the security, the Contractor shall use Government-approved telecommunications equipment, devices, techniques, or services. A list of the approved equipment, etc. may be obtained from (identify where list can be obtained). Equipment, devices, techniques, or services used by the Contractor must be compatible or interoperable with (list and identify the location of any telecommunications security equipment, device, technique, or service currently being used by the technical or requirements organization or other offices with which the Contractor must communicate).

(d) Except as may be provided elsewhere in this contract, the Contractor shall furnish all telecommunications security equipment, devices, techniques, or services necessary to perform this contract. The Contractor must meet ownership eligibility conditions for communications security equipment designated as controlled cryptographic items.

(e) The Contractor agrees to include this clause, including this paragraph (e), in all subcontracts which require securing telecommunications.

(End of clause)

252.239-7017 - Notice of Supply Chain Risk - FEB 2019

(a) Definitions. "Supply chain risk," as used in this provision, means the risk that an adversary may sabotage, maliciously introduce unwanted function, or otherwise subvert the design, integrity, manufacturing, production, distribution, installation, operation, or maintenance of a covered system so as to surveil, deny, disrupt, or otherwise degrade the function, use, or operation of such system (10 U.S.C. 2339a).

(b) In order to manage supply chain risk, the Government may use the authorities provided by section 10 U.S.C. 2339a. In exercising these authorities, the Government may consider information, public and non-public, including all-source intelligence, relating to an offeror and its supply chain.

(c) If the Government exercises the authority provided in 10 U.S.C. 2339a to limit disclosure of information, no action undertaken by the Government under such authority shall be subject to review in a bid protest before the Government

Accountability Office or in any Federal court.

(End of provision)

252.239-7018 - Supply Chain Risk - FEB 2019

(a) Definitions. As used in this clause-

"Information technology" (see 40 U.S.C 11101(6)) means, in lieu of the definition at FAR 2.1, any equipment, or interconnected system(s) or subsystem(s) of equipment, that is used in the automatic acquisition, storage, analysis, evaluation, manipulation, management, movement, control, display, switching, interchange, transmission, or reception of data or information by the agency.

(1) For purposes of this definition, equipment is used by an agency if the equipment is used by the agency directly or is used by a contractor under a contract with the agency that requires--

(i) Its use; or

(ii) To a significant extent, its use in the performance of a service or the furnishing of a product.

(2) The term "information technology" includes computers, ancillary equipment (including imaging peripherals, input, output, and storage devices necessary for security and surveillance), peripheral equipment designed to be controlled by the central processing unit of a computer, software, firmware and similar procedures, services (including support services), and related resources.

(3) The term "information technology" does not include any equipment acquired by a contractor incidental to a contract.

"Supply chain risk," means the risk that an adversary may sabotage, maliciously introduce unwanted function, or otherwise subvert the design, integrity, manufacturing, production, distribution, installation, operation, or maintenance of a covered system so as to surveil, deny, disrupt, or otherwise degrade the function, use, or operation of such system (see 10 U.S.C. 2339a).

(b) The Contractor shall mitigate supply chain risk in the provision of supplies and services to the Government.

(c) In order to manage supply chain risk, the Government may use the authorities provided by 10 U.S.C. 2339a. In exercising these authorities, the Government may consider information, public and non-public, including all-source intelligence, relating to a Contractor's supply chain.

(d) If the Government exercises the authority provided in 10 U.S.C. 2339a to limit disclosure of information, no action undertaken by the Government under such authority shall be subject to review in a bid protest before the Government Accountability Office or in any Federal court.

52.204-24 - Representation Regarding Certain Telecommunications and Video

Surveillance Services or Equipment - AUG 2020 The Offeror shall not complete the representation in this provision if the Offeror has represented that it "does not provide covered telecommunications equipment or services as a part of its offered products or services to the Government in the performance of any contract, subcontract, or other contractual instrument" in the provision at 52.204-26, Covered Telecommunications

Equipment or Services-Representation, or in paragraph (v) of the provision at 52.212-3, Offeror Representations and

Certifications-Commercial Items.

(a) Definitions. As used in this provision--

"Covered telecommunications equipment or services", "critical technology", and "substantial or essential component" have the meanings provided in clause 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance

Services or Equipment.

(b) Prohibition. Section 889(a)(1)(A) of the John S. McCain National Defense Authorization Act for Fiscal Year 2019 (Pub. L.

115-232) prohibits the head of an executive agency on or after August 13, 2019, from procuring or obtaining, or extending or renewing a contract to procure or obtain, any equipment, system, or service that uses covered telecommunications equipment or services as a substantial or essential component of any system, or as critical technology as part of any system. Contractors are not prohibited from providing--

The offeror shall not complete the representation at paragraph (d)(1) of this provision if the offeror has represented that it "does not provide Covered Telecommunications Equipment or Services as a part of its offered products or services to the Government in the performance of any contract, subcontract, or other contractual instrument" in the provision at 52.204-26, Covered

Telecommunications Equipment or Services--Representation, or in paragraph (v) of the provision at 52.212-3, offeror

Representations and Certifications-Commercial Items.

(a) Definitions. As used in this provision--

Backhaul, Covered Telecommunications Equipment or Services, critical technology, interconnection arrangements, reasonable inquiry, roaming, and substantial or essential component have the meanings provided in the clause 52.204-25, Prohibition on contracting for Certain Telecommunications and Video Surveillance Services or equipment.

(b) Prohibition.

(1) Section 889(a)(1)(A) of the John S. McCain national defense authorization Act for fiscal year 2019 (Pub. L. 115-232) prohibits the head of an executive agency on or after August 13, 2019, from procuring or obtaining, or extending or renewing a contract to procure or obtain, any equipment, system, or service that uses Covered Telecommunications Equipment or Services as a substantial or essential component of any system, or as critical technology as part of any system. Nothing in the prohibition shall be construed to--

(i) Prohibit the head of an executive agency from procuring with an entity to provide a service that connects to the facilities of a third-party, such as backhaul, roaming, or interconnection arrangements; or

(ii) Cover telecommunications equipment that cannot route or redirect user data traffic or cannot permit visibility into any user data or packets that such equipment transmits or otherwise handles.

(2) Section 889(a)(1)(B) of the John S. McCain national defense authorization Act for fiscal year 2019 (Pub. L. 115-232) prohibits the head of an executive agency on or after August 13, 2020, from entering into a contract or extending or renewing a contract with an entity that uses any equipment, system, or service that uses Covered Telecommunications Equipment or

Services as a substantial or essential component of any system, or as critical technology as part of any system. This prohibition applies to the use of Covered Telecommunications Equipment or Services, regardless of whether that use is in performance of work under a Federal contract. Nothing in the prohibition shall be construed to--

(i) Prohibit the head of an executive agency from procuring with an entity to provide a service that connects to the facilities of a third-party, such as backhaul, roaming, or interconnection arrangements; or

(ii) Cover telecommunications equipment that cannot route or redirect user data traffic or cannot permit visibility into any user data or packets that such equipment transmits or otherwise handles.

(c) Procedures. The offeror shall review the list of excluded parties in the System for Award Management (SAM)

(https://www.sam.gov) for entities excluded from receiving federal awards for "Covered Telecommunications Equipment or

Services".

(d) Representation. The offeror represents that--

(1) It [ ] will, [ ] will not provide Covered Telecommunications Equipment or Services to the Government in the performance of any contract, subcontract or other contractual instrument resulting from this solicitation. The offeror shall provide the additional disclosure information required at paragraph (e)(1) of this section if the offeror responds "will" in paragraph (d)(1) of this section; and

(2) After conducting a reasonable inquiry, for purposes of this representation, the offeror represents that--

It [ ] does, [ ] does not use Covered Telecommunications Equipment or Services, or use any equipment, system, or service that uses Covered Telecommunications Equipment or Services. The offeror shall provide the additional disclosure information required at paragraph (e)(2) of this section if the offeror responds "does" in paragraph (d)(2) of this section.

(e) Disclosures.

(1) Disclosure for the representation in paragraph (d)(1) of this provision. If the offeror has responded "will" in the representation in paragraph (d)(1) of this provision, the offeror shall provide the following information as part of the offer:

(i) For covered equipment--

(A) The entity that produced the covered telecommunications equipment (include entity name, Unique Entity

Identifier, CAGE code, and whether the entity was the original equipment manufacturer (OEM) or a distributor, if known);

(B) A description of all covered telecommunications equipment offered (include brand; model number, such as

OEM number, manufacturer part number, or wholesaler number; and item description, as applicable); and

(C) Explanation of the proposed use of covered telecommunications equipment and any factors relevant to determining if such use would be permissible under the prohibition in paragraph (b)(1) of this provision.

(ii) For covered services--

(A) If the service is related to item maintenance: A description of all covered telecommunications services offered

(include on the item being maintained: Brand; model number, such as OEM number, manufacturer part number, or wholesaler number; and item description, as applicable); or

(B) If not associated with maintenance, the Product Service Code (PSC) of the service being provided; and explanation of the proposed use of covered telecommunications services and any factors relevant to determining if such use would be permissible under the prohibition in paragraph (b)(1) of this provision.

(2) Disclosure for the representation in paragraph (d)(2) of this provision. If the offeror has responded "does" in the representation in paragraph (d)(2) of this provision, the offeror shall provide the following information as part of the offer:

(i) For covered equipment--

(A) The entity that produced the covered telecommunications equipment (include entity name, Unique Entity

Identifier, CAGE code, and whether the entity was the OEM or a distributor, if known);

(B) A description of all covered telecommunications equipment offered (include brand; model number, such as

OEM number, manufacturer part number, or wholesaler number; and item description, as applicable); and

(C) Explanation of the proposed use of covered telecommunications equipment and any factors relevant to determining if such use would be permissible under the prohibition in paragraph (b)(2) of this provision.

(ii) For covered services--

(A) If the service is related to item maintenance: A description of all covered telecommunications services offered

(include on the item being maintained: Brand; model number, such as OEM number, manufacturer part number, or wholesaler number; and item description, as applicable); or

(B) If not associated with maintenance, the PSC of the service being provided; and explanation of the proposed use of covered telecommunications services and any factors relevant to determining if such use would be permissible under the prohibition in paragraph (b)(2) of this provision.

(End of provision)

52.204-25 - Prohibition on Contracting for Certain Telecommunications and Video

Surveillance Services or Equipment - AUG 2020

( (a) Definitions. As used in this clause--

Backhaul means intermediate links between the core network, or backbone network, and the small subnetworks at the edge of the network (e.g., connecting cell phones/towers to the core telephone network). Backhaul can be wireless (e.g., microwave) or wired (e.g., fiber optic, coaxial cable, Ethernet).

Covered foreign country means The People's Republic of China.

Covered Telecommunications Equipment or Services means-

(1) Telecommunications equipment produced by Huawei Technologies company or ZTE Corporation (or any subsidiary or affiliate of such entities);

(2) For the purpose of public safety, security of Government facilities, physical security surveillance of critical infrastructure, and other national security purposes, video surveillance and telecommunications equipment produced by Hytera

Communications Corporation, Hangzhou Hikvision Digital Technology company, or Dahua Technology company (or any subsidiary or affiliate of such entities);

(3) Telecommunications or video surveillance services provided by such entities or using such equipment; or

(4) Telecommunications or video surveillance equipment or services produced or provided by an entity that the Secretary of Defense, in consultation with the Director of National Intelligence or the Director of the Federal Bureau of Investigation, reasonably believes to be an entity owned or controlled by, or otherwise connected to, the Government of a Covered foreign country.

critical technology means-

(1) Defense articles or defense services included on the United States Munitions List set forth in the International Traffic in Arms Regulations under subchapter M of chapter I of title 22, Code of Federal Regulations;

(2) Items included on the Commerce Control List set forth in Supplement No. 1 to part 774 of the Export Administration

Regulations under subchapter C of chapter VII of title 15, Code of Federal Regulations, and controlled-

(i) Pursuant to multilateral regimes, including for reasons relating to national security, chemical and biological weapons proliferation, nuclear nonproliferation, or missile technology; or

(ii) For reasons relating to regional stability or surreptitious listening;

(3) Specially designed and prepared nuclear equipment, parts and components, Materials, software, and technology covered by part 810 of title 10, Code of Federal Regulations (relating to assistance to foreign atomic energy activities);

(4) Nuclear facilities, equipment, and material covered by part 110 of title 10, Code of Federal Regulations (relating to export and import of nuclear equipment and material);

(5) Select agents and toxins covered by part 331 of title 7, Code of Federal Regulations, part 121 of title 9 of such Code, or part 73 of title 42 of such Code; or

(6) Emerging and foundational technologies controlled pursuant to section 1758 of the Export Control Reform Act of 2018

(50 U.S.C. 4817).

Interconnection arrangements means arrangements governing the physical connection of two or more networks to allow the use of another's network to hand off traffic where it is ultimately delivered (e.g., connection of a customer of telephone provider A to a customer of telephone company B) or sharing data and other information resources.

Reasonable inquiry means an inquiry designed to uncover any information in the entity's possession about the identity of the producer or provider of Covered Telecommunications Equipment or Services used by the entity that excludes the need to include an internal or third-party audit.

Roaming means cellular communications services (e.g., voice, video, data) received from a visited network when unable to connect to the facilities of the home network either because signal coverage is too weak or because traffic is too high.

substantial or essential component means any component necessary for the proper function or performance of a piece of equipment, system, or service.

(b) Prohibition.

(1) Section 889(a)(1)(A) of the John S. McCain national defense authorization Act for fiscal year 2019 (Pub. L. 115-232) prohibits the head of an executive agency on or after August 13, 2019, from procuring or obtaining, or extending or renewing a contract to procure or obtain, any equipment, system, or service that uses Covered Telecommunications Equipment or Services as a substantial or essential component of any system, or as critical technology as part of any system. The contractor is prohibited from providing to the Government any equipment, system, or service that uses Covered Telecommunications

Equipment or Services as a substantial or essential component of any system, or as critical technology as part of any system, unless an exception at paragraph (c) of this clause applies or the covered telecommunication equipment or services are covered by a waiver described in FAR 4.2104.

(2) Section 889(a)(1)(B) of the John S. McCain national defense authorization Act for fiscal year 2019 (Pub. L. 115-232) prohibits the head of an executive agency on or after August 13, 2020, from entering into a contract, or extending or renewing a contract, with an entity that uses any equipment, system, or service that uses Covered Telecommunications Equipment or

Services as a substantial or essential component of any system, or as critical technology as part of any system, unless an exception at paragraph (c) of this clause applies or the covered telecommunication equipment or services are covered by a waiver described in FAR 4.2104. This prohibition applies to the use of Covered Telecommunications Equipment or Services, regardless of whether that use is in performance of work under a Federal contract.

(c) Exceptions. This clause does not prohibit contractors from providing--

(1) A service that connects to the facilities of a third-party, such as backhaul, roaming, or interconnection arrangements;

or

(2) Telecommunications equipment that cannot route or redirect user data traffic or permit visibility into any user data or packets that such equipment transmits or otherwise handles.

(d) Reporting requirement.

(1) In the event the contractor identifies Covered Telecommunications Equipment or Services used as a substantial or essential component of any system, or as critical technology as part of any system, during contract performance, or the contractor is notified of such by a subcontractor at any tier or by any other source, the contractor shall report the information in paragraph

(d)(2) of this clause to the contracting officer, unless elsewhere in this contract are established procedures for reporting the information; in the case of the Department of Defense, the contractor shall report to the website at https://dibnet.dod.mil. For indefinite delivery contracts, the contractor shall report to the contracting officer for the indefinite delivery contract and the contracting officer(s) for any affected order or, in the case of the Department of Defense, identify both the indefinite delivery contract and any affected orders in the report provided at https://dibnet.dod.mil.

(2) The contractor shall report the following information pursuant to paragraph (d)(1) of this clause

(i) Within one business day from the date of such identification or notification: the contract number; the order number(s), if applicable; supplier name; supplier Unique Entity Identifier (if known); supplier Commercial and Government Entity

(CAGE) code (if known); brand; model number (original equipment manufacturer number, manufacturer part number, or wholesaler number); item description; and any readily available information about mitigation actions undertaken or recommended.

(ii) Within 10 business days of submitting the information in paragraph (d)(2)(i) of this clause: any further available information about mitigation actions undertaken or recommended. In addition, the contractor shall describe the efforts it undertook to prevent use or submission of Covered Telecommunications Equipment or Services, and any additional efforts that will be incorporated to prevent future use or submission of Covered Telecommunications Equipment or Services.

(e) Subcontracts. The contractor shall insert the substance of this clause, including this paragraph (e) and excluding paragraph (b)(2), in all subcontracts and other contractual instruments, including subcontracts for the acquisition of commercial items.

STANDARD PROVISION - 01 - DITCO BASIC AGREEMENT - AUG 2017

To be eligible to receive any Order or Circuit Demand resulting from this Inquiry, Contractor/Telecommunication Provider (TP) shall have a DITCO Basic Agreement (BA) signed by both the Government and the Contractor. See Federal Acquisition

Regulation 16.702 -- Basic Agreements. DITCO BA contains additional terms and conditions that shall be incorporated into any

Order or Circuit Demand by reference. Contractor/TP shall identify its assigned DITCO BA number (e.g., HC10XXXXHXXXX) and agreement date in its quote. Contractors/TPs that do not have a current DITCO BA must execute one with the appropriate

DITCO Office prior to submitting any quotes. The Contractor/TP must provide the following organizational information as registered in System of Award Management (SAM):

Legal Business Name

Address

DUNS

CAGE

Phone and FAX number

POC if different from the POC for Government Business as indicated in your SAM registration

Name and title of organization official to sign the Basic Agreement

DITCO Europe Basic Agreements: Contractor/TPs must obtain a blank BA from the Integrated Defense Enterprise Acquisition

System (IDEAS) Contractor web site under references tab https://depsland.csd.disa.mil/html/vendor.html; complete it with their organizational information, sign, and return BA to the following applicable email address for signature before submitting any quotes. Any questions concerning the DITCO Europe BA may be emailed to disa.stuttgart.ditco.mbx.pl511@mail.mil, and any questions concerning the DITCO SWA BA may be emailed to disa.stuttgart.ditco.mbx.pl52@mail.mil.

DITCO U.S. Basic Agreements: Contractor/TPs should review the template of the DITCO US BA located on the above website and email their organizational information as registered in SAM.gov to email address disa.scott.ditco.mbx.basic-agreements@mail.mil. DITCO-Scott will validate the Contractor/TP organizational information, process a new BA and send it to the Contractor/TP for final review and completion of blocks 30a, 30b, and 30c of the BA document (Solicitation/Contract/Order for Commercial items (SF 1449)). The BA must be signed and returned before submitting any quotes.