Attachment-Circuit_Parameters_and_Testing_Requirements_for_Solicitation_QA868_4-26-18.docx

Circuit Parameters and Testing Requirements for Solicitation HC101318QA868

TEST & ACCEPTANCE INSTRUCTIONS: CONUS ETHERNET

VENDOR WILL PERFORM ACCEPTANCE TESTING IN ACCORDANCE WITH EITHER

RFC-6815 OR ITU-T Y.1564. SPECIFICALLY, FRAME SIZES OF

64,128,256,512,1024,1280 AND 1518 BYTES MUST BE USED. THE

TEST MUST VERIFY LENGTH OF RECEIVED FRAMES, INDICATE NUMBER

OF FRAMES DROPPED, NUMBER OF FRAMES RECEIVED OUT OF ORDER,

AND DUPLICATE FRAMES. TESTS MUST BE BI-DIRECTIONAL USING THE

SAME DATA RATE IN EACH DIRECTION. BURST TESTS MUST BE RUN TO

DETERMINE MINIMUM INTERVAL BETWEEN FRAMES THAT CAN BE

PROCESSED WITHOUT FRAME LOSS.

A THROUGHPUT TEST IS REQUIRED INDICATING THE FASTEST RATE AT

WHICH TEST FRAMES CAN BE TRANSMITTED WITHOUT FRAME LOSS. A

SEPARATE THROUGHPUT TEST MUST BE RUN WITH FRAMES ADDRESSED TO

THE HARDWARE BROADCAST ADDRESS CONSTITUTING AT LEAST 1% OF

THE TEST STREAM AND BE EVENLY DISTRIBUTED THROUGHOUT THE

TEST. A LATENCY TEST MUST BE RUN FOR A PERIOD OF NO LESS THAN

120 SECONDS, AND REPEATED NO LESS THAT 20 TIMES. THE TEST STREAM

FOR THE LATENCY TEST SHOULD BE RUN AT THE THROUGHPUT RATE FOR

CORRESPONDING FRAME SIZES FROM THE THROUGHPUT TEST.

END TO END LATENCY WILL BE CALCULATED AS THE AVERAGE OVER THE

20 TEST RUNS. FRAME LOSS RATE TESTS SHOULD BE RUN AT THE FRAME

RATE CORRESPONDING TO THE MAXIMUM FRAME RATE, AND REDUCED BY

10% INTERVALS UNTIL THERE ARE AT LEAST TWO CONSECUTIVE RUNS IN

WHICH NO FRAMES ARE LOST.

THROUGHPUT TEST RESULTS:

PASSING RATE 100% FOR ALL FRAME BYTE

SIZES EXERCISED. FRAME LOSS RATE (%) RESULTS: FRAME LOSS RATE

LESS THAN 0.01% FOR ALL FRAME BYTE SIZES EXERCISED.

LATENCY WILL BE MEASURED WILL BE ACCORDING TO THE FOLLOWING

MAXIMUM TRANSMISSION DELAY FOR ANY CIRCUIT UP TO 500 MILES

AIR-MILES IN LENGTH SHALL BE NO GREATER THAN 13MS ONE-WAY AND

ANY POINT-TO-POINT CIRCUIT LONGER THAN 500 AIR-MILES SHALL

BE NO GREATER THAN 50MS ONE WAY WITHIN THE 48 CONTINENTAL

STATES. ANY APS SWITCHOVER SHALL TAKE LESS THAN 50 MILLISECONDS.

A. ANY ADDRESSEE ON THE TSO WILL NOTIFY ALL

ADDRESSEES IMMEDIATELY BY MESSAGE IDENTIFYING ANY ISSUES,

PROBLEMS, OR SITUATIONS WHICH MAY PREVENT OR DELAY THE

IMPLEMENTATION OF THIS TELECOMMUNICATIONS SERVICE ORDER (TSO).

ALL STATIONS WILL REVIEW THE CONFIGURATION, EQUIPMENT, CONTACT

NUMBERS AND ADDRESSES CONTAINED IN THIS TSO AND PROVIDE UPDATES

TO ORIGINATOR OF TSO ANY ERRORS SO THAT SUBSEQUENT TSOS MAY BE

UPDATED.

B. COMPLETION REPORT: FOR STATION DESIGNATED IN PARAGRAPH 2H AS

CCO/CMO, FOR THIS ACTION COMPLETION REPORTS WILL BE SUBMITTED IAW

DISAC 310-130-1, CHAPTER 2 BY DISA GLOBAL IP, DSN 312-770-8627;

COML 618-220-8627. ALL OTHER CCO/CMO RESPONSIBILITIES REMAIN

WITH THE DESIGNATED CCO/CMO IAW DISAC 310-70-1, CHAPTER 8.

C. IMPLEMENTATION ASSISTANCE: FOR DISN CORE / DEDICATED / NIPRNET /

SIPRNET / VPN CIRCUIT ACTIVATION ASSISTANCE OR SERVICE IMPLEMENTA

TION INQUIRIES/SCHEDULING, CONTACT THE DISA GLOBAL RF ACTIVATIONS

TEAM VIA EMAIL, DISA.SCOTT.CONUS.MBX.RF-CIRCUIT-ACTIVATIONS@MAIL

.MIL, OR CALL DSN 770-8627; COML 618-220-8627.

D. IMPLEMENTATION ASSISTANCE CONTINUED: FOR CIRCUIT INSTALLATION

ASSISTANCE WITH THE COMMERCIAL LEASED PATH, CONTACT

DCP COMMERICIAL ACTIVATION TEAM (CAT) AT D312-850-0820,

C614-692-0820

E. DD FORM 1368: DD FORM 1368'S (MODIFIED USE OF LEASED

COMMUNICATION FACILITIES), OR EMAIL EQUIVALENT, WILL BE

SUBMITTED, AS REQUIRED, ON THIS CIRCUIT IAW DISAC-DITCO 350-135-1

BY THE STATION DESIGNATED IN PARAGRAPH 2H AS CCO/CMO. GUIDANCE

ON SUBMISSION IS AVAILABLE AT

HTTP://WWW.DITCO.DISA.MIL/CORPORATELIBRARY/HOME.ASP. CLICK ON

"350-135-1, DEFENSE COMMERCIAL COMMUNICATIONS ACQUISITION

PROCEDURES."

F. CONNECTION APPROVAL PROCESS STATEMENT: FOR IP CUSTOMER/USER: IAW

CJCSI 6211.02C AND DISA DIRECTIVES **FAILURE TO REGISTER AND

OBTAIN DISA CONNECTION APPROVAL (IATC/ATC) FOR YOUR CIRCUIT WILL

RESULT IN DELAY OF CIRCUIT ACTIVATION**

CONNECTIVITY TO THE SIPRNET, NIPRNET AND VPN MUST COMPLY

WITH THE SECURITY ACCREDITATION REQUIREMENTS SPECIFIED IN THE

CONNECTION PROCESS GUIDE (CPG) AND CURRENT DOD POLICY. THE CPG

CAN BE VIEWED AT THE FOLLOWING URL: HTTP://WWW.DISA.MIL/CONNECT.

IT IS THE RESPONSIBILITY OF THE CUSTOMER TO ENSURE THAT ALL

NEW, REHOMED, AND UPGRADED IP CIRCUITS ARE REGISTERED. THE

IATC/ATC LETTERS MUST BE OBTAINED THROUGH THE UNCLASIFIED

CONNECTION APPROVAL OFFICE (UCAO) OR CLASIFIED CONNECTION

APPROVAL OFFICE (CCAO) BEFORE CIRCUIT ACTIVATION.

FOR ALL REGISTERED CIRCUITS, THE REGISTRATION MUST BE

UPDATED TO REFLECT CURRENT ACCREDITATION INFORMATION AND A COPY

OF THE ACCREDITATION DECISION, CONSENT TO MONITOR, AND ENCLAVE

TOPOLOGY MUST BE SUBMITTED TO THE UCAO (NIPR) OR CCAO (SIPR).

THE CCSD AND TRACKING NUMBER ARE REQUIRED TO UPDATE AN EXISTING

RECORD.

FOR A DETAILED DESCRIPTION OF THE DISN CONNECTION PROCESS

VISIT HTTP://WWW.DISA.MIL/CONNECT. IF YOU ARE UNABLE TO ACCESS

THE WEBSITE OR REQUIRE SPECIFIC GUIDANCE FOR UNIQUE CUSTOMER

ISSUES, PLEASE CONTACT THE CONNECTION APPROVAL OFFICE (CAO) AT

CMCL: 301-225-2900/1, DSN 312-375-2900/1

G. UNSATISFACTORY SERVICE REPORTING INSTRUCTIONS: FOR UNSATISFACTORY

SERVICE OR TO REPORT EQUIPMENT AND/OR CIRCUIT PROBLEMS INVOLVING

DISA PROVIDED TRANSPORT AND/OR EQUIPMENT, PLEASE CONTACT THE

DISN CUSTOMER CONTACT CENTER (DCCC) TOLL FREE NUMBER IS

1-844-347-2457 (1-844-DISA HLP) OPTION 2, COML 1-614-692-0032

OPTION 2, DSN 312-850-0032 OPTION 2.