HC101317QA885-0003.v0_5-1-18.pdf

IQO INQUIRY

FM: PL8211

TO: Contractors

DATE (MM/DD/YYYY): 4/30/2018

SUBJECT: HC101317QA885-0003 Amend: 0003

A. TYPE ACTION: AMEND

1. PURPOSE: THE PURPOSE OF THIS AMENDMENT TO SOLICITATION HC101317QA885 IS

TO:

1. CHANGE THE SERVICE DATE TO BE MET TO 01 SEP 18 SIP;

2. CHANGE Z LOCATION FROM MECHANICSBURG, PA TO FORT BELVOIR, VA.

3. ADD NEW PARAGRAPH 9 AT PURPOSE STATEMENT TO CLARIFY THAT 50 METERS

PHYSICAL SEPARATION REQUIREMENT STILL APPLIES TO THIS REQUIREMENT, BUT THE

DIVERSITY REQUIREMENT IS WAIVED ONLY AS TO THE PART OF THE REQUIREMENT

ROUTE THAT PASSES THROUGH DOWNTOWN PHILADELPHIA, PA.

4. UPDATED CIRCUIT PARAMETERS AND TESTING REQUIREMENTS ATTACHED.

RECAP

1. SUBMIT A QUOTE TO PROVIDE, INSTALL, AND MAINTAIN AN UNPROTECTED OC-48C

LEASED IP BACKBONE TRUNK BETWEEN DISA IE1 PROVIDED CISCO ASR-9010 ROUTER

(UJEWLKH040) (IPT-PEX2) BLDG 120, ROOM 107B, 120 LANSDOWNE ROAD; LAKEHURST

NAVAL AIR CENTER, LAKEHURST, NJ 08733, AND DISA IE1 PROVIDED CISCO ASR-9010

ROUTER (UJEWMEC030) (IPT-PE1) BLDG 2310, ROOM 130, 8575 JOHN J. KINGMAN ROAD, FT

BELVIOR, VA 22060.

A. CONTRACTORS SHALL MEET RTD OF 10 MILLISECONDS

B. VENDOR MUST DELIVER OC-48C SERVICE 2W (UNPROTECTED) FROM COML DEMARC TO

GOVERNMENT SERVICE DELIVERY POINT AT BOTH LOCATIONS.;

C. VENDOR MUST PROVIDE LIGHT LEVEL READINGS (DB LOSS) ON EXTENSION FROM

COMMERCIAL POP TO GOVERNMENT SERVICE DELIVERY POINT (SDP) AT BOTH

LOCATIONS PRIOR TO CIRCUIT TURN UP TO THE GOVERNMENT ENSURING LEVELS ARE

WITHIN SPECS. LIGHT LEVELS MUST BE ADJUSTED TO -5 TO -13.

D. VENDOR MUST CONDUCT WALK-THROUGH SITE SURVEY PRIOR TO INSTALLATION AT

BOTH LOCATIONS.

E. VENDOR MUST CONTACT DISA GOC IP BACKBONE ENGINEERING AND IMPLEMENTATION

GROUP UPON RECEIPT OF A VALID TSO TO ESTABLISH THE COORDINATION AND

ACTIVATION PROCESS. (C) 618-220-8627 (D) 770-8627.

F. VENDOR MUST CONDUCT A SATISFACTORY 24 HOUR END TO END TEST PRIOR TO TURN

OVER TO THE GOVERNMENT FOR ACCEPTANCE TESTING.

G. OC-48C SERVICE MUST PASS A DOCUMENTED SATISFACTORY 24 HOUR END TO END

TEST IAW ITU STANDARD M.2101 PRIOR TO TURN UP TO THE GOVERNMENT.

HC101317QA885-0003

2. EACH CONTRACTOR IS RESPONSIBLE FOR READING AND COMPLYING WITH ALL

TECHNICAL ASPECTS OF THIS SOLICITATION, TO INCLUDE READING AND AGREEING

WITH THE STANDARD PROVISIONS, ATTACHMENTS LISTING SPECIFIC TECHNICAL

REQUIREMENTS, PRICE QUOTE REQUIREMENTS, AND REQUESTED SERVICE DATE.

FAILURE TO READ AND ADHERE TO ANY PORTION OF THE INQUIRY SHALL RENDER THE

QUOTE NON-COMPLIANT AND RESULT IN IT BEING EXCLUDED FROM EVALUATION AND

AWARD.

3. THE SERVICE DATE TO BE MET IS: 01 SEP 18 (SIP). THE GOVERNMENT ASSUMES THAT

CONTRACTORS HAVE CONSIDERED ALL ISSUES THAT MAY IMPACT THE SERVICE DATE.

THE GOVERNMENT MAY CANCEL, TERMINATE, OR REQUEST CONSIDERATION IAW

STANDARD PROVISION 42 FOR FAILURE TO MEET CONTRACTUAL SERVICE DATE OR

COMPLY WITH ANY CONTRACT TERMS OR CONDITIONS.

4. CONTRACTORS SHALL SUBMIT QUOTES IAW STANDARD PROVISION 04. QUOTES SHALL

INCLUDE SUFFICIENT DETAIL FOR EFFECTIVE EVALUATION AND SHOULD NOT SIMPLY

REPHRASE OR RESTATE THE GOVERNMENT REQUIREMENTS. RATHER, THEY MUST

PROVIDE CONVINCING RATIONALE TO ADDRESS HOW THE CONTRACTOR INTENDS

TO MEET THE REQUIREMENT. IN RESPONSE TO THIS SOLICITATION, NO TERMS OR

CONDITIONS PLACED UPON THE GOVERNMENT, NOR ASSUMPTIONS WILL BE ACCEPTED.

RESPONSES TO CONTRACTORS ARE ENCOURAGED TO SUBMIT QUESTIONS AND REQUEST

CLARIFICATIONS OF THE REQUIREMENT (S) BEFORE SUBMITTING QUOTES. QUESTIONS

SHALL BE SUBMITTED TO CONTRACT SPECIALIST AND CONTRACTING OFFICER DURING

THE SOLICITATION PHASE ONLY, AND RESPONSES FOR ALL INTERESTED PARTIES WILL

BE POSTED TO FEDBIZOPPS. . QUOTES MUST BE UPLOADED TO IDEAS AND A COURTESY

COPY MAY BE SENT TO THE FOLLOWING MAILBOX. DISA SCOTT AFB DITCO MAILBOX

VENDOR QUOTES . THIS MAILBOX MAY ALSO BE USED WHEN HAVING ISSUES UPLOADING

QUOTES IN IDEAS.

5. THIS REQUIREMENT MUST BE WORKED IN CONJUNCTION WITH SOLICITATION

HC101317QA905/TSR RU15FEB175129.

6. CONTRACTOR SHALL PROVIDE COLOR POWERPOINT DRAWINGS SHOWING THE ROUTES

FROM THE COMMERCIAL DEMARKS TO THE SUPPORTING CENTRAL OFFICES AND/OR

WIRING CENTERS, ENSURING THE PHYSICAL END TO END DIVERSITY REQUIREMENTS ARE

BEING MET. DRAWINGS MUST INCLUDE SEPARATION DISTANCES, TOTAL FIBER MILES

AND ROUND TRIP DELAY BASED ON ACTUAL DISTANCE IN MILES. REFER TO STANDARD

PROVISION 39 FOR SPECIFIC DOCUMENTATION REQUIREMENTS. SAMPLE DRAWINGS ARE

INCLUDED THE ATTACHMENTS.

7. ESTABLISH TSP: TSP0GKVQT-01

8. THIS REQUIREMENT MUST BE ENGINEERED AND PROVISIONED TOTALLY DIVERSE

END TO END TO GOVERNMENT'S SERVICE DELIVERY POINTS (SDP'S) FROM TSR

RU15FEB175129 (HC101317QA885); MEANING THAT PHYSICAL PATHS ARE TOTALLY

SEPARATE INCLUDING MAN HOLES, CONDUIT, (CENTRAL OFFICE LOCATIONS), AND FIBER

BUILDS. ADDITIONALLY AS A MINIMUM MUST HAVE 50 METERS PHYSICAL SEPARATION

FROM TSR RU15FEB175129.

9. THE DIVERSITY REQUIREMENT STATED ABOVE OF 50 METERS MINIMUM PHYSICAL

SEPARATION FROM TSR RU15FEB175129 IS WAIVED IN DOWNTOWN PHILADELPHIA, PA,

BUT REMAINS IN PLACE FOR THE REST OF THE PATH OF THIS REQUIREMENT.

M. ADDITIONAL INFORMATION:

3. TSR NUMBER: RU15FEB175128D

4. CCSD: XXXXBTE4

Z. DITCO CONTACT:

Christopher OConnor

618-229-9712 christopher.t.oconnor2.civ@mail.mil

Paul A. Heard

DITCO Contracting Officer

Add the following:

LOCATION OF TERMINATION A:

ADDRESS: BLDG 120, 120 Lansdowne Road, Lakehurst NAC, Lakehurst, NJ 08733.

ROOM: 107B

LOCATION: ACC

EXTENSION OF TELECOMMUNICATIONS SERVICE: All facilities between vendor's commercial communications interface point and termination location shall be provided by vendor. All cables shall be run in accordance with local site standards

INTERFACE: INTERFACE: ELECTRICAL: OPTICAL; PHYSICAL: LC;; (PHYSICAL) LC;(ELECTRICAL) OPTICAL

DEMARK: (BLDG) HANGAR 1; 1 LANSDOWNE ROAD; LAKEHURST NAEC, LAKEHURST, NJ, 08733,

TELEPHONE ROOM; N/A FL

NPA/NXX: 732/323

UNIQUE INSTALLATION FACTORS: (1) FIBER CABLE, ON-BASE, SINGLE-MODE, 1310NM,

87CS PERSONNEL

(2) FIBER TERMINATING PATCH PANEL (GFE)(SITE

PROVIDED)

(3) FIBER CABLE X-CONNECT, IN-HOUSE, INSIDE WIRE,

SINGLE-MODE, 1310NM, TELCO

(4) COMMERCIAL FIBER POINT OF PRESENCE

(5) CISCO ASR-9010 ROUTER (GFE)(DISA IE1

PROVIDED) NODE ID:UJEWLKH040

(6) OPTICAL INTERFACE CARD (GFE)(DISA IE1

PROVIDED) OC48C /PO0/0/0

RESERVATION: 17786.

IP ADDRESS: 33.20.15.82

SUBNET MASK: 255.255.255.252

(7) FIBER CABLE, ON-BASE, SINGLE-MODE, 1310NM,

87CS PERSONNEL

AMPLIFYING INFO:

A. 87CS PERSONNEL ARE RESPONSIBLE FOR INSTALLATION AND MAINTENANCE OF SINGLE MODE FIBER FROM

LINE SIDE OF SITE PROVIDED FIBER TERMINATING PATCH PANEL BLDG 120, ROOM 107B TO LINE SIDE OF SITE

PROVIDED FIBER TERMINATING PATCH PANEL HANGAR 1, TELEPHONE ROOM.

B. VENDOR IS RESPONSIBLE FOR INSTALLATION AND MAINTENANCE OF SINGLE MODE FIBER FROM DROP SIDE OF

SITE PROVIDED FIBER PATCH PANEL HANGAR 1, TELEPHONE ROOM TO DROP SIDE OF COMMERCIAL FIBER POINT

OF PRESENCE FIBER DISTRIBUTION PANEL HANGAR 1, TELEPHONE ROOM. COORDINATE TYPE CONNECTORS FOR

TERMINATION TO DISA PROVIDED PATCH PANEL.

C. VENDOR MUST COORDINATE WITH GOVERNMENT SITE PERSONNEL TO CONDUCT WALK THROUGH SITE

SURVEY FOR EXACT CABLE FT. FROM SITE PROVIDED FIBER TERMINATING PATCH PANEL HANGAR 1, TELEPHONE

ROOM TO COMMERCIAL FIBER POINT OF PRESENCE HANGAR 1, TELEPHONE ROOM.

D. VENDOR MUST PROVIDE FIBER STRANDS FROM SITE PROVIDED FIBER PATCH PANEL TO COMMERCIAL DEMARC

LOCATION WITHOUT SPLICING AND OR USE OF CONNECTORS TO CONNECT 2 OR MORE FIBER STRANDS MEANING

THE FIBER CANNOT BE BROKEN IN THE MIDDLE AND MUST BE CONTINUOUS.

E. VENDOR MUST SCHEDULE/COORDINATE WITH POC'S LISTED ON THIS ORDER 72 HOURS IN ADVANCE PRIOR TO

SITE SURVEYS OR INSTALLATIONS.

F. DISA IE4 IS RESPONSIBLE FOR INSTALLATION AND GSM-O FOR MAINTENANCE OF CISCO ASR-9010 ROUTER, OPTICAL INTERFACE CARD BLDG 120, ROOM 107B.

G. DISA IE4 IS RESPONSIBLE FOR INSTALLATION AND GSM-O FOR SINGLE MODE FIBER FROM OPTICAL INTERFACE

CARD INSTALLED IN CISCO ASR-9010 ROUTER TO DROP SIDE OF DISA IE1 PROVIDED FIBER TERMINATING PATCH

PANEL INSTALLED IN THE CISCO ASR-9010 ROUTER. COORDINATE TYPE OF CONNECTORS.

H. VENDOR IS RESPONSIBLE FOR INSTALLATION AND MAINTENANCE OF SINGLE MODE FIBER FROM LINE SIDE OF

DISA IE1 PROVIDED FIBER TERMINATING PATCH PANEL INSTALLED IN CISCO ASR-9010 ROUTER SUITE

(UJEWLKH040) BLDG 120, ROOM 107B TO DROP SIDE OF SITE PROVIDED FIBER PATCH PANEL BLDG 120, ROOM

107B. COORDINATE TYPE CONNECTORS FOR TERMINATION TO DISA IE1 PROVIDED PATCH PANEL. COORDINATE

WITH 87CS PERSONNEL FOR TYPE CONNECTORS AND FIBER TERMINATION ASSIGNMENTS AT SITE PATCH PANEL

BLDG 120, ROOM 107B CORRESPONDING TO FIBER PAIR ASSIGNMENTS AT SITE PROVIDED FIBER PATCH PANEL

HANGAR 1, TELEPHONE ROOM.

I. VENDOR MUST PROVIDE FIBER STRANDS FROM CISCO ASR-9010 ROUTER SUITE FIBER PATCH PANEL TO SITE

PROVIDED FIBER PATCH PANEL WITHOUT SPLICING AND OR USE OF CONNECTORS TO CONNECT 2 OR MORE

FIBER

STRANDS MEANING THE FIBER CANNOT BE BROKEN IN THE MIDDLE AND MUST BE CONTINUOUS.

J. CIRCUIT MUST BE TAGGED WITH LOCAL CIRCUIT ID AND LONG HAUL CIRCUIT NO. AT LINE SIDE OF DISA IE1

PROVIDED FIBER TERMINATING PATCH PANEL BLDG 120, ROOM 107B AND AT DROP SIDE OF SITE PROVIDED FIBER

INSIDE WIRE INSTALLATION / MAINTENANCE REQUIRED: CPIWI-YES/CPIWM-YES

CONTACT: (PMRY POC) JONATHAN T OKEEFE

(UNCLASS USER) JONATHAN.OKEEFE@US.AF.MIL

(CMCL) 609-754-2978

(ALT POC) CHRISTOPHER S KAILIS

(UNCLASS ORG) CIRCUIT_ACTIONS@US.AF.MIL

(UNCLASS USER) CHRISTOPHER.KAILIS@US.AF.MIL

(CMCL) 609-754-4847

(DSN) 650-4847

Add the following:

LOCATION OF TERMINATION B:

ADDRESS: (BLDG) 2310; 8575 JOHN J. KINGMAN RD, FORT BELVOIR, VA 22060

ROOM: 130; 1 FL

LOCATION: BCC

EXTENSION OF TELECOMMUNICATIONS SERVICE: All facilities between vendor's commercial communications interface point and termination location shall be provided by vendor. All cables shall be run in accordance with local site standards

INTERFACE: INTERFACE: ELECTRICAL: OPTICAL; PHYSICAL: LC;; (PHYSICAL) LC; (ELECTRICAL) OPTICAL

DEMARK: (BLDG) 2310

(RM) 130

(FL) 1

8575 J.J. KINGMAN ROAD

FORT BELVOIR, VA 22060

NPA/NXX: 703/806

UNIQUE INSTALLATION FACTORS: (1) FIBER CABLE X-CONNECT, IN-HOUSE, INSIDE WIRE, SINGLE-MODE, 1310NM, TELCO

(2) TELCO MULTIPLEX (COMMERCIAL FIBER POINT OF PRESENCE) COMMERCIAL CARRIER SYSTEM (LOCAL

EXCHANGE CARRIER)

(3) NODE ID: UJEWBEL030

(4) PORT: 1/0/2

(5) IP ADDRESS: 33.20.15.81/30

AMPLIFYING INFO:

A. VENDOR IS RESPONSIBLE FOR INSTALLATION AND MAINTENANCE OF THE SERVICE FROM THE LINE SIDE OF

THE DISA IE1 PROVIDED FIBER TERMINATING PATCH PANEL INSTALLED IN THE CISCO ASR-9010 ROUTER SUITE

(UJEWBEL030) BLDG 2310, RM 130 TO THE DROP SIDE OF THE COMMERCIAL FIBER POINT OF PRESENCE FIBER

DISTRIBUTION PANEL BLDG 2310, RM 130 USING SINGLE MODE FIBER. COORDINATE TYPE CONNECTORS TO BE

USED FOR TERMINATION TO THE DISA PROVIDED PATCH PANEL.

B. VENDOR MUST COORDINATE WITH GOVERNMENT SITE PERSONNEL TO CONDUCT WALK THROUGH SITE

SURVEYS FOR EXACT CABLE FT. FROM THE DISA PROVIDED FIBER TERMINATING PATCH PANEL INSTALLED IN THE

CISCO ASR-9010 ROUTER SUITE BLDG 2310, RM 130 TO THE COMMERCIAL FIBER POINT OF PRESENCE BLDG 2310, RM 130.

C. VENDOR MUST PROVIDE FIBER STRANDS FROM THE DISA PROVIDED FIBER PATCH PANEL INSTALLED IN THE

CISCO ASR-9010 ROUTER TO THE COMMERCIAL DEMARC LOCATION WITHOUT SPLICING AND OR USE OF

CONNECTORS TO CONNECT 2 OR MORE FIBER STRANDS MEANING THE FIBER CANNOT BE BROKEN IN THE MIDDLE

AND MUST BE CONTINUOUS.

D. VENDOR MUST SCHEDULE/COORDINATE WITH THE POC'S LISTED ON THIS ORDER 72 HOURS IN ADVANCE PRIOR

TO SITE SURVEYS OR INSTALLATIONS.

E. DISA IE4 IS RESPONSIBLE FOR INSTALLATION AND GSM-O FOR MAINTENANCE OF THE CISCO ASR-9010 ROUTER, OPTICAL INTERFACE CARD BLDG 2310, RM 130.

F. DISA IE4 IS RESPONSIBLE FOR INSTALLATION AND GSM-O FOR SERVICE FROM THE INTERFACE CARD

INSTALLED IN THE ROUTER TO THE DROP SIDE OF THE DISA IE1 PROVIDED FIBER TERMINATING PATCH PANEL

INSTALLED IN THE CISCO ASR-9010 SUITE, USING SINGLE-MODE FIBER JUMPERS. COORDINATE TYPE OF

CONNECTORS.

G. VENDOR IS RESPONSIBLE FOR INSTALLATION AND MAINTENANCE OF THE SERVICE FROM THE LINE SIDE OF

THE DISA IE1 PROVIDED FIBER TERMINATING PATCH PANEL INSTALLED IN THE CISCO ASR-9010 ROUTER SUITE

(UJEWBEL030) BLDG 2310, RM 130 TO THE DROP SIDE OF THE COMMERCIAL FIBER POINT OF PRESENCE FIBER

DISTRIBUTION PANEL BLDG 2310, RM 130 USING SINGLE MODE FIBER. COORDINATE TYPE CONNECTORS TO BE

USED FOR TERMINATION TO THE DISA PROVIDED PATCH PANEL.

H. THE CIRCUIT MUST BE TAGGED WITH THE LOCAL CIRCUIT ID AND LONG-HAUL CIRCUIT NO. AT THE LINE SIDE OF

THE DISA PROVIDED FIBER TERMINATING PATCH PANEL BLDG 2310, RM 130 AND AT THE DROP SIDE OF THE

VENDOR'S FIBER DISTRIBUTION PANEL INSTALLED IN THEIR COMMERCIAL SUITE. ADDITIONALLY, VENDOR MUST

SHOW SITE PERSONNEL LISTED ON THIS ORDER THE EXACT TERMINATION POINT WHEN SERVICE IS COMPLETE.

INSIDE WIRE INSTALLATION / MAINTENANCE REQUIRED: CPIWI-YES/CPIWM-YES

CONTACT: (PRMY POC) TECH CONTROL

EMAIL: USARMY.BELVOIR.NETCOM.LIST.596SIGCO-TECH-CONTROL-FACILITY-STAFF@MAIL.MIL

USARMY.BELVOIR.NETCOM.MBX.596SIGCO-TECH-CONTROL-FACILITY STAFF@MAIL.MIL

D655-2030

C703-805-2030

(ALT POC) DARRIAN OWENS

(UNCLASS EMAIL) DARRIAN.L.OWENS.MIL@MAIL.MIL;

(DSN) 656-5697/D655-2030

(CMCL) 703-806-5690

C703-805-2030

EMAIL: USARMY.BELVOIR.NETCOM.LIST.596SIGCO-TECH-CONTROL-FACILITY-STAFF@MAIL.MIL

USARMY.BELVOIR.NETCOM.MBX.596SIGCO-TECH-CONTROL-FACILITY-STAFF@MAIL.MIL