Asbestos_Report_(St._Albans,_VT).pdf

General Services Administration

Federal Building & U.S. Post Office

Asbestos Survey Report

January 26, 2012

Federal Building & U.S. Post Office 56 South Main Street

St. Albans, VT 05478-2202

Prepared By

Federal Occupational Health JFK Building Room E-110

Government Center Boston, MA 02203

GSA 2011 Asbestos Survey Report – Federal Building & U.S. Post Office

Table of Contents

I. List of Abbreviations

II. Executive Summary

Table 1 - SUMMARY OF ACM IDENTIFIED AT THE SITE

III. Introduction and Background

IV. Project Tasks

V. Sample Locations & Sample Analysis

Table 2 - SUMMARY OF PLM ANALYTICAL DATA

VI. ACM Condition Assessment

Table 3 – SUMMARY OF ACM PHYSICAL CONDITION

Table 4 – POTENTIAL FOR DISTURBANCE OF SUSPECT MATERIAL

VII. Sampling Protocol

Asbestos Sample Collection

VIII. Analytical Methods

Asbestos Samples

IX. Waste Management

X. Record Keeping

XI. Summary and Recommendations

XII. References

Attachments:

Appendix – A: Asbestos Containing Materials – Certified Laboratory Analytical Results Appendix – B: Photographs of ACM Building Materials Sampled Appendix – C: Asbestos Sampling Locations – Floor Plans and Drawings Appendix – D: Inspector Licenses and Company Certifications

I. List of Abbreviations ACM Asbestos-Containing Material

AHERA Asbestos Hazard Emergency Response Act

DS Dispersion Staining

EA Each

EPA Environmental Protection Agency

Flame AAS Flame Atomic Absorption Spectroscopy

FOH Federal Occupational Health

GSA Government Services Administration HA Homogeneous Area LF Linear Feet NESHAP National Emissions Standards for Hazardous Air Pollutants OSHA Occupational Safety and Health Administration O&M Operation & Maintenance PLM Polarized Light Microscopy PPE Personal Protective Equipment SF Square Feet SOW Scope of Work TEM Transmission Electron Microscopy US United States USEPA United States Environmental Protection Agency VDH Vermont Department of Health

VTH Vermont Department of Health

II. Executive Summary

On December 08 and 09, 2011, Mr. Patrick Bomba and Mr. Michael J. Reeder, who are representatives of the Federal Occupational Health (FOH) on behalf of the General Services Administration (GSA), conducted an asbestos survey of the U.S. Post Office and Customs House located at 56 South Main Street in St. Albans, Vermont (Site).

The purpose of this assessment is to determine if asbestos containing material (ACM) is present at the Site by collecting non-destructive samples of accessible suspect ACM throughout the interior of the Site. The exterior of the Site was not evaluated as part of this survey.

During the collection of suspect ACM samples, the FOH representatives implemented controls, techniques, and protocols to minimize occupational exposure to asbestos, which are in accordance with the Vermont Department of Health and other applicable laws and regulations.

All sampling and analysis of the suspect ACMs were performed in accordance with applicable requirements by qualified FOH inspectors and by laboratories accredited by the EPA.

During the course of the asbestos survey, FOH asbestos inspector(s) were accompanied by:

Mr. Jack Darling, GSA Building Manager and/or designated representative.

The FOH asbestos inspectors collected a total of one hundred nine (109) individual suspected ACM samples throughout accessible areas of the Site. According to analytical results (Appendix B), asbestos was identified in thirteen (13) of the one hundred nine (109) samples collected.

The ACMs and associated quantities identified at the Site are summarized in the following Table:

Table 1 - SUMMARY OF ACM IDENTIFIED AT THE SITE

SAMPLE

NUMBER

MATERIAL

TYPE

MATERIAL

LOCATION

ASBESTOS

CONTENT

QUANTITY

(SF/LF/EA)

162747-05 Tan Window Caulk Stored Windows in Attic 1-2% Chrysotile 5 Stacks of Windows

162747-16A

162747-17A

162747-18A

9” X 9” White Floor Tile

& Black Mastic

Room 225

Room 224

Room 220

2-4% Chrysotile

1,800 SF

162747-43

162747-44

162747-45

Hard Mud Joint

Room 131 Pipe

Room 131 Pipe

Room 131 Pipe

5-10% Chrysotile

10-15% Chrysotile

10-20% Chrysotile

196 EA

NUMBER

MATERIAL

TYPE

MATERIAL

LOCATION

ASBESTOS

CONTENT

QUANTITY

(SF/LF/EA)

162747-65

162747-66

162747-67

White Pipe Insulation

Room B35

Room B35

Room B35

10-20% Chrysotile

10-20% Chrysotile

10-20% Chrysotile

340 LF

162747-68

162747-69

162747-70

Brown Pipe Insulation

Room B35

Room B35

Room B35

3-6% Chrysotile

3-6% Chrysotile

3-6% Chrysotile

390 LF

Note: All Quantities are estimates. SF=Square Feet, LF=Linear Feet, and EA = Each

III. Introduction and Background

According to supplied information, the Site includes an approximate 64,564-square foot, two-story, with basement and attic Federal Building and U.S. Post Office.

IV. Project Tasks

Project tasks included:

Reviewing existing drawings and specifications provided by the GSA for original construction and renovation information (as available) regarding the installation of suspect ACM.

Reviewing historic asbestos inspection reports (as available) to determine the existence of previously identified homogeneous areas (HAs) at each functional space.

Verify if previously conducted asbestos inspection was performed in accordance with the Asbestos Hazard Emergency Response Act (AHERA) regulations. If not, the number of additional bulk samples necessary for compliance with the AHERA regulations will be calculated.

Developing sampling protocols in accordance to AHERA regulations.

Sampling and analyzing various interior building materials to determine if ACM are present.

Developing maps for each floor showing areas where suspect ACM samples were collected and ACM was identified.

Note all areas identified as inaccessible (e.g., pipe chases, wall voids, elevator shafts, locked doors, etc.) during the sampling event.

Asbestos bulk samples of various building materials and surfaces were collected at the Site and submitted to the FOH Denver Asbestos Laboratory to undergo Polarized Light Microscopy with Dispersion Staining (PLM/DS) analysis in accordance with the “Method for the Determination of Asbestos in Bulk Building Materials” (US EPA Method 600/R-93/116, July 1993).

V. Sample Locations & Sample Analysis

FOH’s accredited asbestos inspectors conducted the survey and collected samples of suspected ACM in general accordance with the Environmental Protection Agency’s (EPAs) interpretations and guidelines of AHERA. The inspectors surveyed the Site and collected samples of all suspected ACM. The PLM analytical data of asbestos samples collected at the Site is summarized in Table 2.

Table 2 - SUMMARY OF PLM ANALYTICAL DATA

NUMBER

MATERIAL

TYPE

MATERIAL

LOCATION

ASBESTOS

CONTENT

QUANTITY

(SF/LF/EA)

162747-01

162747-02

162747-03

Brown Fiber Board Roof

Panel

Attic Ceiling

Attic Ceiling

Attic Ceiling

ND

ND

NA

162747-04

162747-05

162747-06

Tan Window Caulk

Stored Windows in Attic

Stored Windows in Attic

Stored Windows in Attic

ND

1-2% Chrysotile

5 Stacks of

Windows

162747-07

162747-08

162747-09

Tan Carpet Mastic

Room 204

2nd Floor Main Corridor

Room 202A

ND

162747-10

162747-11

162747-12

Brown Sheet Flooring

Room 204

Room 206

Room 202A

ND

162747-13

162747-14

162747-15

White Plaster

2nd Floor Janitor Closet

Room 224 Wall

Room 220 Wall

ND

162747-16

162747-17

162747-18

9” X 9” White Floor Tile

Room 225

Room 224

Room 220

2-4% Chrysotile

1,800 SF

162747-19

162747-20

162747-21

White Pipe Mastic

Above 2nd Floor Hallway

Above 2nd Floor Hallway

Above 2nd Floor Hallway

ND

162747-22

162747-23

162747-24

Black Wall Mastic

Room 223 Exterior Wall

Room 224 Exterior Wall

Room 220 Exterior Wall

ND

162747-25

162747-26

162747-27

Tan Cove Base Mastic

Room 224

Room 223

Room 220

ND

162747-28

162747-29

162747-30

Gray Wall Grout

Men’s Restroom 2nd Floor LL

Men’s Restroom 2nd Floor LL

Men’s Restroom 2nd Floor LL

ND

162747-31

162747-32

162747-33

2’ X 5’ White Ceiling Tile

Room 131

1st Floor Elevator Lobby

2nd Floor LL Hallway

ND

MATERIAL

TYPE

MATERIAL

LOCATION

ASBESTOS

CONTENT

QUANTITY

(SF/LF/EA)

162747-34

162747-35

162747-36

Black Wall Mastic

Room 131 Exterior Wall

Room 131 Exterior Wall

Room 131 Exterior Wall

ND

162747-37

162747-38

162747-39

Room 131 Wall

1st Floor Elevator Lobby Wall

Room B36 Wall

ND

162747-40A

162747-40B

162747-41A

162747-41B

162747-42A

162747-42B

Sheetrock &

Joint Compound

Room 204 Closet

ND

ND

ND

162747-43

162747-44

162747-45

Hard Mud Joint

Room 131 Pipe

5-10%

Chrysotile

10-15%

Chrysotile

10-20%

Chrysotile

196 EA

162747-46

162747-47

162747-48

Tan & Black Carpet Mastic

Room 131 Corner Office

Room 131

Room 131

ND

162747-49

162747-50

162747-51

Room 120A

Room 153A

ND

162747-52

162747-53

162747-54

12” X 12” White Floor Tile

Basement Hallway

Basement Hallway

Basement Hallway

ND

162747-55

162747-56

162747-57

12” X 12” Gray Floor Tile

Basement Break Room

Basement Break Room

Basement Break Room

ND

162747-58

162747-59

162747-60

12” X 12” White & Gray

Floor Tile

Basement Hallway

(Stairwell Landing)

Basement Hallway

(Stairwell Landing)

Basement Hallway

(Stairwell Landing)

162747-61 White Pipe Mastic Basement Boiler Room ND NA

MATERIAL

TYPE

MATERIAL

LOCATION

ASBESTOS

CONTENT

QUANTITY

(SF/LF/EA)

162747-62

162747-63A

162747-63B

162747-64A

162747-64B

Boiler Flue Insulation

Basement Boiler Room

ND

162747-65

162747-66

162747-67

White Pipe Insulation

Room B35

Chrysotile

10-20%

Chrysotile

Chrysotile

340 LF

162747-68

162747-69

162747-70

Brown Pipe Insulation

Room B35

Room B35

3-6% Chrysotile

3-6% Chrysotile

3-6% Chrysotile

390 LF

162747-71

162747-72

162747-73

White Ceiling Texture

Basement Hallway

Basement Hallway

Basement Hallway

ND

162747-74

162747-75

162747-76

Brown Duct Mastic

Room B21

Room B21A

Room B21A

ND

162747-77A

162747-77B

162747-78A

162747-78B

162747-79A

162747-79B

Green Speck Sheet

Flooring & Tan Mastic

Room B21A

ND

ND

ND

162747-80A

162747-80B

162747-81A

162747-81B

162747-82A

162747-82B

Gray Speckled Sheet

Flooring & Black Mastic

Room B14

ND

ND

ND

162747-83

162747-84

162747-85

Room B14 Wall

Room B23 Wall

Basement Men’s

Restroom Wall

MATERIAL

TYPE

MATERIAL

LOCATION

ASBESTOS

CONTENT

QUANTITY

(SF/LF/EA)

162747-86

162747-87

162747-88

Room B23

Room B14

Room B24

ND

162747-89

162747-90

162747-91

2’ X 5” White Ceiling Tile

Room B14

Room B12

ND

162747-92

162747-93

162747-94

2’ X 2’ White Ceiling Tile

Room B23

Room B23

ND

162747-95

162747-96

162747-97

Black Vapor Barrier

Room B15A

Room B15A

Room B15A

ND

162747-98A

162747-98B

162747-99A

162747-99B

162747-100A

162747-100B

ND

ND

ND

162747-101

162747-102

162747-103

Gray Duct Mastic

Garage

Garage

Garage Mechanical Room

ND

162747-104A

162747-104B

162747-105A

162747-105B

162747-106A

162747-106B

1st Floor Hallway

Room 142A

GSA Main Hallway

ND

ND

ND

162747-107

162747-108

162747-109

2’ X 2’ Rough White

Ceiling Tile

1st Floor Hallway

Room 142A

GSA Main Hallway

ND

Note: All Quantities are estimates. SF=Square Feet, LF=Linear Feet, EA = Each, & ND=Non-Detected

VI. ACM Condition Assessment

The FOH asbestos inspector(s) categorized the various suspect ACMs (Surfacing Material, Miscellaneous Material, and Thermal System Insulation) collected at the Site by visual inspection and classified these materials by referencing the following definitions:

Surfacing and Miscellaneous Material

Good Condition (GC) – Material with no visible damage or deterioration, or showing only very limited damage or deterioration.

Damaged (D) – The surface is crumbling, blistered, water-stained, gouged, marred or otherwise abraded over less than one-tenth (1/10) of the surface if the damage is evenly distributed (one-quarter if the damage is localized).

Significantly Damaged (SG) – The surface is crumbling or blistered over at least 1/10 of the surface if the damaged is evenly distributed (one-quarter if the damage is localized); 1/10 (one-quarter, if localized) of material hanging from surface, deteriorated, or showing adhesive failure; and/or water stains, gouges, or mars over at least 1/10 of the surface if the damage is evenly distributed (one-quarter if the damage is localized).

AHERA Definition of Damaged Friable Surfacing Miscellaneous ACM:

“Friable surfacing miscellaneous ACM, which has deteriorated or sustained physical injury such that the internal structure (cohesion) of the material is inadequate or, if applicable, which has delaminated such that the bond to the substrate (adhesion) is adequate or which for any other reason lacks fiber cohesion or adhesion qualities. Such damage or deterioration may be illustrated by the separation of ACM into layers; separation of ACM from the substrate; flaking, blistering, or crumbling of ACM surface; water damage; significant or repeated water stains, scrapes, gouges, mars or other signs of physical injury on the ACM. Asbestos debris originating from the ACBM in question may also indicate damage.”

Thermal System Insulation

Good Condition (GC) – Material with no visible damage or deterioration, or showing only very limited damage or deterioration.

Damaged (D) – A few water stains or less than 1/10 of insulation with missing jackets and/or crushed insulation or water stains, gouges, punctures, or mars on up to 1/10 of the insulation if the damage is evenly distributed (or up to one-quarter if the damaged is localized).

Significantly Damaged (SG) – Missing jackets on at least 1/10 of the piping or equipment and/or crushed or heavily gouged or punctured insulation on at least 1/10 of pipe runs/risers, boiler, tank, duct, etc., if the damage is evenly distributed (or up to one-quarter if the damaged is localized).

Note: Accumulation of powder, dust, or debris similar in appearance to the suspect material on surfaces beneath the pipe/boiler/tank/duct, etc. can be used as confirmatory evidence.

AHERA Definition of Damaged or Significantly Damaged Thermal System Insulation:

“Thermal system insulation ACM on pipes, boilers, tanks, ducts, and other thermal system insulation equipment which has lost its structural integrity, or its covering, in whole or in part, is crushed, water-stained, gouged, punctured, missing, or not intact such that is not able to contain fibers. Damage may be further illustrated by occasional punctures, gouges, or other signs of physical injury to ACM;

occasional water damage on the protective coverings/jackets; or exposed ACM ends or joints. Asbestos debris, originating from the ACBM in question may also indicate damage.”

Table 3 – SUMMARY OF ACM PHYSICAL CONDITION

SAMPLE

No.

162747-

MATERIAL

TYPE

Surfacing Material Thermal System Insulation Miscellaneous Material

Friable Non-

Friable

Condt. Friable Non-

Friable

Condt. Friable Non-

Friable

Condt.

Tan Window

Caulk

√ GC

16A

17A

18A

9” X 9” White

Floor Tile

√ GC

Hard Mud Joint √ GC

White Pipe

Insulation

√ GC

Brown Pipe

Insulation

√ GC

Note: GC = Good Condition, D = Damaged, and SD = Significantly Damaged

The FOH asbestos inspector(s) also determined the ACMs potential for contact, the influence of vibration, and the potential for air erosion by referencing the following definitions:

Potential for Contact with the Material

High: Service workers work in the vicinity of the material more than once per week, or

The material is in a public area (e.g., hallway, corridor, auditorium) and accessible to building occupants.

Moderate: Service workers work in the vicinity of the material once per month to once per week, or

The material is in a room or office and accessible to the occupants.

Low: Service workers work in the vicinity of the material less than once per month, or

The material is visible but not within reach of building occupants.

Influence of Vibration

High: Loud motors or engines present (e.g., some fan rooms), or

Intrusive noises or easily sensed vibrations (e.g., major airports, a major highway).

Moderate: Motors or engines present but not obtrusive (e.g., ducts vibrating but no fan in the area), or

Occasional loud sounds (e.g., a music room)

Low/None: None of the above.

Potential for Air Erosion

High: High velocity air (e.g., elevator shaft, fan room).

Moderate: Noticeable movement of air (e.g., air shaft, ventilator air stream).

Low/None: None of the above.

Table 4 – POTENTIAL FOR DISTURBANCE OF SUSPECT MATERIAL

No.

162747-

MATERIAL

TYPE

Potential for Contact Influence of Vibration Potential for Air Erosion

High Moderate Low High Moderate Low High Moderate Low

Tan Window

Caulk

16A

17A

18A

9” X 9” White

Floor Tile

Hard Mud Joint √ √ √

White Pipe

Insulation

Brown Pipe

Insulation

VII. Sampling Protocol

Asbestos Sample Collection

Representative bulk samples of suspect asbestos containing building materials (ACMBs) were collected at the Site building. The building was divided into separate and distinct project areas.

For the purpose of this survey, each area was inspected and sampled as a separate functional space having separate and distinct homogenous materials. Homogenous material determination was based on the following criteria:

Similar physical characteristics (same color and texture, etc.)

Application (sprayed-on, troweled-on, assembly into a system etc.)

Material function (thermal insulation, floor tile, wallboard system etc.)

Samples of suspected ACM were collected and placed into sealed plastic bags and shipped via overnight delivery to the FOH Denver Asbestos Laboratory to undergo PLM/DS analysis in accordance with the “Method for the Determination of Asbestos in Bulk Building Materials” (US

EPA Method 600/R-93/116, July 1993).

VIII. Analytical Methods

Asbestos Samples

Polarized Light Microscopy Analysis Methodology

The FOH Denver Asbestos Laboratory, which is a National Voluntary Laboratory Accreditation

Program certified laboratory, provided the asbestos analytical services. The laboratory analyzed the suspected ACM by PLM utilizing the EPAs Test Methods: Methods for the determination of Asbestos in Bulk Building Materials (EPA 600/R-93/116, July 1993) and the

McCrone Research Institute’s The Asbestos Particle Atlas as method references. Additional treatment and tests may be required to accurately define the sample composition (i.e. ashing, extraction, acetone treatment, and transmission electron microscopy).

The sample analysis was performed by using the bulk sample for visual observation and slide preparation(s) for microscopic examination and identification. The lab analyzed the samples for asbestos (chrysotile, amosite, crocidolite, anthophyllite, and actinolite/tremolite), fibrous non-asbestos constituents (mineral wool, cellulose, etc.) and non-fibrous constituents. Using a stereoscope, the microscopist visually estimated relative amounts of each constituent by determining the volume of each constituent in proportion to the total volume of the sample.

IX. Waste Management

FOH representatives did not generate any waste material while conducting the asbestos survey at the Site. The small amount of material collected while conducting these surveys was submitted to the laboratories for analysis, and there was no excess amount of material left that required disposal.

X. Record Keeping

In order to document the progress of this project, the FOH inspector maintained field notes, developed site sketches, and made notations on site diagrams and floor plans as the fieldwork progressed. Copies of the certified laboratory asbestos analytical reports and chain–of-custodies are included in Appendix A. Photos of the suspected ACM are included in Appendix B.

Copies of asbestos sample locations are included in Appendix C and company certifications and inspector licenses are included in Appendix D.

XI. Summary and Recommendations

During the period of December 08 and 09, 2011 FOH inspectors collected a total of one hundred nine (109) individual suspected ACM samples at the Site. Analytical results of the asbestos samples collected indicated that thirteen (13) of the one hundred nine (109) suspected ACM samples contained at least one percent or more of asbestos. An unknown amount of assumed ACM pipe insulation exists inside pipe chases within the building.

Since asbestos was identified in concentrations greater than one percent, any construction or renovation activities performed in the future are subject to applicable rules and regulation concerning the disturbance or removal of the ACM. The Vermont Department of Health rules apply to all buildings which are subject to public occupancy, or to which the general public has access. Any person disturbing, removing, or encapsulating asbestos in any public building including, renovation, dismantling, or demolition, shall notify the Vermont Department of

Health in writing ten (10) working days prior to the start date of the abatement project. It is the responsibility of the building Owner or it’s Representative to ensure that only current Vermont

State license asbestos abatement companies and workers engage in asbestos related activities.

The U.S. EPA regulations do not require removal of asbestos-containing materials that are in good conditions. However, personnel who may be involved with building renovations will need to be advised of the presence of asbestos, and appropriate measures may be warranted in order to assure the identified ACM in the building are not disturbed during renovation activities. If the ACM left in place is disturbed during renovation activities, the materials must be handled and disposed in accordance with the applicable State and Federal regulations.

XII. References

EPA, Guidance on Systematic Planning Using the Data Quality Objective Process, EPA, QA/G-4, February 2006.

EPA, Guidance for Quality Assurance Project Plans, EPA QA/G-5, December 2002.

EPA, Framework for Investigating Asbestos-Contaminated Superfund Sites, OSWER Directive #9200.0-

68, September 2008.

EPA, Guidance on Choosing a Sampling Design for Environmental Data Collection, EPA QA/G-5S, December 2002.

Appendix – A

Asbestos Containing Materials Certified Laboratory Analytical Results

Appendix – B

Photographs of ACM Building Materials Sampled

GSA 2011 Asbestos Survey Report – Courthouse and U.S. Post Office

1. Sample Numbers 162747-04, 05 & 06 which include tan window caulk.

2. Sample Numbers 162747-16, 17, & 18 which include 9” X 9” white floor tile.

3. Sample Number 162747-43 which includes a hard mud joint. 4. Sample Number 162747-44 which includes a hard mud joint.

5. Sample Number 162747-45 which includes a hard mud joint. 6. Sample Number 162747-65, which includes white pipe insulation.

GSA 2011 Asbestos Survey Report – Courthouse and U.S. Post Office

7. Sample Number 162747-66 which includes white pipe insulation.

8. Sample Number 162431-67, which includes white pipe insulation.

9. Sample Number 162747-68 which includes brown pipe insulation.

10. Sample Number 162747-69, which includes brown pipe insulation.

11. Sample Number 162431-70, which includes brown pipe insulation.

Appendix – C

Asbestos Sampling Locations – Floor Plans and Drawings

Asbestos Survey

56 Main St.

St. Albans, Vermont

ACM Brown Pipe

Federal Building and U.S. Post Office St. Albans, VT.

Brown Pipe Insulation Basement

Mechanical Room

Women’s Restroom

GSA Storage

Janitor Closet

Men’s Restroom

Stairs Up

RM B28A

RM B26

RM B24

RM B22

RM B14

RM B1 RM B2

ELEV.

Mechanical Room

B11

RM B15A

Ramp Down

MECH.RM

Garage

RM B44 RM B19

RM

B41

MECH.

RM

RM B45

RM B42

RM B21

RM B23

RM B35 RM B33

RM B36

RM B21A 88

RM B12

3 Pipes

RM B28

RM B28B

RM B20

RM B18

56 Main St.

St. Albans, Vermont

Federal Building and U.S. Post Office St. Albans, VT.

Basement Hard Mud Joints

Mechanical Room

Women’s Restroom

GSA Storage

Janitor Closet

Men’s Restroom

Stairs Up

RM B28 RM B28A

RM B28B

RM B26

RM B24

RM B22

RM B20

RM B18

RM B14

RM B1 RM B2

ELEV.

Mechanical Room

B11

RM B15A

Ramp Down

MECH.RM

Garage

RM B44 RM B19

RM

B41

MECH.

RM

RM B45

RM B42

RM B21

RM B23

RM B35 RM B33

RM B36

RM B21A 88

RM B12

X 2

X 2

X 27

X 7 X 48

X 14

X 10

X 10

X 62

X = Total Number of Hard Mud Joints in Area

56 Main St.

St. Albans, Vermont

ACM White Pipe

St. Albans, VT.

White Pipe Insulation and Hard Mud Joints

Basement

Mechanical Room

Women’s Restroom

GSA Storage

Janitor Closet

Men’s Restroom

Stairs Up

RM B28 RM B28A

RM B26

RM B24

RM B22

RM B20

RM B18

RM B14

RM B1 RM B2

ELEV.

Mechanical Room

B11

RM B15A

Ramp Down

MECH.RM

Garage

RM

B41

MECH.

RM

RM B45

RM B42

RM B21

RM B23

RM B33

RM B36

RM B21A 88

RM B12

RM B28B

RM B35

RM B44 RM B19

X2

X2

X27

X7

X48

X14

X4

X10 X10

X10

X62

56 Main St.

St. Albans, Vermont

ACM Locations

Non ACM Locations

ACM 9" X 9" White Floor Tile

Federal Building and U.S. Post Office St. Albans, VT.

Basement

Boiler Room

Women’s Restroom

GSA Storage

Janitor Closet

Men’s Restroom

Stairs Up

RM B28 RM B28A

RM B28B

RM B26

RM B24

RM B22

RM B20

RM B18

RM B14

RM B1 RM B2

ELEV.

Mechanical Room

B11

RM B15A

Ramp Down

MECH.RM

Garage

RM B44 RM B19

RM

B41

MECH.

RM

RM B45

RM B42

RM B21

RM B23

RM B35 RM B33

RM B36

55 56

65 66 67 68 69 70

747576

RM B21A

80 81

RM B12

93 94

959697

101 102

Chase

Break Room

56 Main St.

St. Albans, Vermont

Federal Building and U.S. Post Office St. Albans, VT.

1st Floor Hard Mud Joints

Ramp Down

Men’s Restroom

Women’s Restroom

Elev.

STAIRS

Men’s Restroom

Women’s Restroom

STAIRS

STAIRS

RM 106A RM 107A

RM 109A

RM 113ARM 114A

RM 115A

RM 116ARM 117ARM 118A

RM 120A

RM 121ARM 122A

RM 103C

RM 103D

LOBBY

RM 127A

RM 128A

RM 129A

RM

131A

RM

132A

RM 133A

Break Room

RM 134A

RM 135A

RM 136A RM 131C

Restroom RM 102A RM 104A

RM 131

RM 123A

RM 124A

RM 125A RM 144A RM 143A

RM 142A

RM 146ARM 153A

RM 148A

RM 140A

X 1X 1

X 1 X 1

56 Main St.

St. Albans, Vermont

Sample Locations

U.S. Post Office St. Albans, VT.

1st Floor

Ramp Down

Men’s Restroom

Women’s Restroom

Elev.

STAIRS

36 37

Men’s Restroom

Women’s Restroom

STAIRS

STAIRS

RM 106A RM 107A

RM 109A

RM 113ARM 114A

RM 115A

RM 116ARM 117ARM 118A

RM 120A

RM 121ARM 122A

RM 103C

RM 103D

LOBBY

RM 127A

RM 128A

RM 129A

RM

131A

RM

132A

RM 133A

Break Room

RM 134A

RM 135A

RM 136A RM 131C

Restroom RM 102A RM 104A

RM 131

RM 123A

RM 124A

RM 125A RM 144A RM 143A

RM 142A

RM 146ARM 153A

RM 148A

RM 140A

Chase

Chase

Chase

Chase

Chase

Chase

Chase

Chase

Chase

56 Main St.

St. Albans, Vermont

U.S. Post Office St. Albans, VT.

1st Floor Mezanine

RM 156A

Mechanical Room

RM 157A

RM 158A

Stairs Down

UPUPDown

56 Main St.

St. Albans, Vermont

ACM 9" X 9" White Floor Tile

St. Albans, VT.

2nd Floor White Floor Tile

RM 204

RM 205

RM 203

RM 206

RM 202A

Men’s RR Women’s RR

RM 218

RM 217

RM 216

RM 216ARm 209

RM 209A RM 215

RM 214

RM 210

RM 213

RM 212

RM 211A

RM 211

RM 221

RM 222

Stairs Down

Men’s RR

Women’s

RR

STAIRS

STAIRSVAULT

RM 219

RM 220

RM 223

RM 224

RM 225

56 Main St.

St. Albans, Vermont

U.S. Post Office St. Albans, VT.

2nd Floor

09 12

28 29 30

RM 204

RM 205

RM 203

RM 206

RM 202A

Men’s RR Women’s RR

RM 218

RM 217

RM 216

RM 216ARm 209

RM 209A RM 215

RM 214

RM 210

RM 213

RM 212

RM 211A

RM 211

RM 219

RM 220

RM 225

RM 224

RM 221

RM 222

RM 223

Stairs Down

Men’s RR

Women’s

RR

STAIRS

STAIRSVAULT

56 Main St.

St. Albans, Vermont

Federal Building and U.S. Post Office St. Albans, VT.

Attic Hard Mud Joints

Stairs Down

4 Hard Mud Joints

ACM Hard Mud Joints

Stacked Windows

56 Main St.

St. Albans, Vermont

U.S. Post Office St. Albans, VT.

Attic

01 02

Stairs Down

4 Hard Mud Joints

Stored Stacks of Windows

Appendix – D

Inspector Licenses and Company Certifications