Falcon 4 Manual with Specifications.pdf

USER MANUAL

Table of Contents Safety Information……………………………………...………………3 Specifications………………………………………...…………………4 Main Power Connection…………………………...…………………..5 Signal Connection…………………….…………..…………………...5 Rigging the Fixture……………………………………………………..6 Installation………………………………………………………………6 Parts List………………………………………………………………..7 Accessories……………………………………………………………..8 Cleaning & Maintenance

Check that the unit has not been damaged during transport

Protection Against Fire

1. Maintain a minimum of 1 foot distance from any type of flame.

2. Do Not install the unit to close to a heat source.

3. Make Sure cables are properly secured

4. Maximum surface operating temperature below 115°f

5. Do not operate panel with out secondary ethernet connection covered.

Protection Against Electrical Damage

1. Disconnect power before servicing.

2. For connection to main power supply proceed to page 6.

3. This unit must be earthed. (electronically grounded)

4. Unit must not be left on for a long period of time.

Protection Against Mechanical Hazards

1. Use secondary safety when hanging unit.

2. Use quality rigging equipment when positioning unit.

3. Do not excessed number of hanging units per suspender.

4. Do not ground stack the unit with out proper hardware.

Ingress Protection

IP 65

The IP rating is commonly expressed as IP (Ingress Protection) is followed by 2 numbers (i.e. 65) where the numbers define the fixture rating. The first number indicates the size of a particle that can enter the fixture.. The second number indicates the extent of protection against water entering the fixture. An IP65 rating in this fixture indicates that dust particles can not enter the fixture. And there is protection against powerful water spray from entering the fixture from any direction.

Specifications

Item# MV314 = Falcon 4 IP Pixel Pitch 4.8

LED Type SMD1921 Black Face

Panel Pixel Count 104 x 208

Physical Panel Density Count 21632

Parameter Panel Size 500 X 1000 X 70mm

Module Size 250mm X 250mm

Panel Weight 26.5lb / 12kg

Module Weight 1.76lb / .8kg

Receiving Card Subito

Grayscale (bit) 12-14bit

Grayscale per color (level) 12-14bit

Electronics Refresh Rate (specified at ordering) 1920-3840

Driving Type 1/16

Driving IC ICN-2153

Signal Distance CAT5 Cable 100M

Brightness (nit) 3000nit

Optical Optimal Viewing Angle Horizontal 160°

Optimal Viewing Angle Vertical 160°

AC Input Voltage 100-240V AC 50/60Hz

AC Power Supply Max 300W

AC Maximum Power Input (Full White) 233W / 1.96Amp

AC Average Power Input 150W

Electrical Power Connection Panel Mount Seetronic In/Out

Signal Connection Panel Mount Seetronis Ethernet In/Out

Power Supply G Energy

Power Link at 110V (using Nema 5-15 connection) 8

Power Link at 220V (using Nema 6-20 connection) 20

IP Rating IP 65 Outdoor / Indoor Use

Ambient Average LED lifetime 100,000 Hours

Conditions Working Ambient Temperature 0-40

Working Humidity (RH) 10%-60% Non Condensing

Vertical Rigging Quantity (pcs) Sus 1 =10 / Sus 2=20 / Sus3=30

Installation Stacking Quantity (pcs) with appropriate hardware 20

Optional Curve Panel Available -10° / +10°

Service Screw Module

Specifications and Certification are subject to change with out any prior notice

Main Power Connection

Caution!

1. This unit must be earthed. (electronically grounded)

2. Replace fuse only with the specified type and rating.

3. Power link maximum 8 units at 110V

4. Power link maximum 20 units at 220V

5. Unit uses 2 power female receptacles it is very important to not connect a second separate input feeds into the output labeled connection. They are in-tended to be used as power In and Outputs as labeled.

The occupation of the connection-cable is as follows:

This device is equipped with a auto switching power supply that will allow you to work from 100V-240V 50/60Hz

Caution!

Signal cable should not travel near high output power. As not to interfere with signal Signal cable should not be longer than 100 Meters.

Cable (USA) Cable (EU) Pin 110V

Black Brown

White

Green

Light Blue

Yellow/Green

Live

Neutral

Ground

L

N

220V

110V Connection

220V Connection

N

L

Signal Connection

The fixture is equipped ethernet panel Sockets for signal input and output. Only use a multiple twisted pair cable de-signed for ethernet., in order to connect the controller with the panel or the panel with another.

Caution!

1. The installations must be carried out by an authorized dealer or trained professional.

2. Unit may cause severe injures if you have doubts concerning the safety do not install.

3. Unit is to be 24inches away from flammable materials (decoration material)

4. Use high quality installation equipment to hang unit.

When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.

When rigging the unit always be secured with a secondary safety attachment. The installation location of the panels has got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be checked at least one time a year by a skilled person.

Rigging the Fixture

1. Latch has to be positioned in in the clockwise turning position were the red Open tap is visible.

2. Push latch into the receiving latch position. Make sure the latch insert has passed the locking point and will not release if pulled back

Latch Installation

3. Before tightening the latch make sure the panel is at the correct level and depth as what you would like.

4. Turn the latch counter clockwise so the blue Closed label is showing

1. Press the red release trigger over the closed latch and hold down wile at the same time turning the latch clockwise to loosen latch

Releasing Latch

5. Press on the release pin on the receiver latch to release the main shaft of the latch. For side latch the spring latch will automatical-ly spring out of position. For top latch the latch gravity will re-lease the latch

FALCON 314 ITEM LIST

Part Number Description

MV-300-SUS-3 FALCON 3 UNIT SUSPENDER

MV-300-SUS-2 FALCON 2 UNIT SUSPENDER

MV-300-SUS-1 FALCON 1 UNIT SUSPENDER

MV-300-SUS-CLA SUSPENDER TRUSS CLAMP

MV-300-SUS-EYE SUSPENDER EYE BOLT

MV-300-CAB-POW-LEA POWER LEAD CABLE WITH NEMA 5-15

MV-300-CAB-POW-JUM POWER JUMPER CABLE

MV-300-CAB-SIG-LEA SIGNAL LEAD CABLE

MV-300-CAB-SIG-JUM SIGNAL JUMPER CABLE

CAS-MV-300-6 6 UNIT ROAD CASE

MV-300-HOU-JOI 4 UNIT JOINER

MV-314-REC SUBITO RECEIVING CARD

PARTS

MV-314-LED REPLACEMENT LED

MV-314-LED-MOD REPLACEMENT LED MODULE

MV-314-HUB REPLCEMENT HUB

MV-300-HOU-LAT-TOP TOP LATCH

MV-300-HOU-LAT-SID SID LATCH

MV-314-POW POWER SUPPLY

MV-314-MAS LED MASK

MV-300-SUS-JOI SUSPENDER JOINER

Parts List

Accessories

MV-300-SUS-3

MV-300-SUS-2

MV-300-SUS-1

MV-300-SUS-CLA MV-300-SUS-JOI MV-300-HOU-JOI

Cleaning and Maintenance

Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and electronics checked by an expert every 2 years.

The following points have to be considered during the inspection:

1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.

2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).

3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments.

Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed.

Disconnect from mains before starting maintenance operation!

Caution Danger to life!

We recommend a frequent cleaning of the device. Please use a moist, lint free cloth. Never use alcohol or solvents!

1) The objective lens will require periodic cleaning on usage and environment. Environment with foggers will require more periodic cleaning as fog fluid tends to build up residues, reducing the light output.

2) Lenses may be cleaned with soft brush using soapy water.

3) The interior of the fixture should be cleaned using a vacuum.

Note: There is no serviceable parts inside the device . Maintenance and service operations are to be carried out by au-thorized dealers.

Replacing the fuse: There is no service fuse inside the fixture.

Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by authorized dealers only

Should you have further questions , please contact your dealer.

18668 Highway 16N Helotes, TX 78023

Ph 210-684-2600 Fax 210-855-6279 www.mega.lighting / info@mega.lighting.com

Warranty Information

Warranty Conditions -Unless otherwise stated in writing, your product is covered by a one year parts and labor limited warranty.

-LED’s are not guaranteed to match in color or output.

-It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and reseller or distributor.

If purchase date cannot be provided, date of manufacture will be used to determine warranty period.

-Goods returned under warranty must follow the proper authorization procedure and must be accompanied by a copy of the original invoice.

-Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical means of shipment.

-Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer. MEGA SYSTEMS INC. makes no warranties, express or implied, with respect to any product, and Mega Systems specifically disclaims any warranty of merchantability or fitness for a particular purpose. Mega Systems shall not be liable for any indirect, inci-dental or consequential damage, including lost profit, sustained or incurred in connection with any product or caused by product defect or the partial or total failure of any product regardless of the form of action, weather in contract, tort (including negligence), strict liability or otherwise, and weather or not such damage was foreseen or unforeseen.

- Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Customer Support

Mega View has a customer support line to provide set up help and to answer any question should you encounter a prob-lem. Please visit our website for any other related technical documents. For service related issue please contact our service dept.

Monday—Friday 9am to 6pm CST Voice: 210-684-2600 E-mail: service@megasystemsinc.com

Specifications in this manual are subject to change.

Document Version

Date Fixture Soft-ware Notes

1.1 12/19/2019 V1.1

Manual Version

Please Visit www.megasystemsinc.com for the most up to date manual version