DRAFT_Support_Equipment_Example_ITA.pdf

DRAFT

Support Equipment Design and Manufacture Sample

004493 AB-9 Augmentation Cage Code 98752 Part Number Qty

AB-9 Assembly and Associated Hardware, PN 201522948-10 Prototype to include the following:

Self-test / Calibration ITA and Associated Hardware, PN TBD

NI PXIe-1085, 18 Slot 3U PXI Express Chassis, PN 781813-01

4 Module Bus Test Instruments, PN BI-411-00 2 Dual Port FC Simulyzer in a PCIe card format Single

Function, PN PXIe-FC4SF-4GB

Synchro/Resolver Processor, PN 65CS4-A2210E0- A2210E0-N

Fan Assembly, PN 201117900-10 1

MESS-4 1

MESS-7 1

ENVID GEN-510 with option 3 2

AB-9 Assembly and Associated Hardware, PN 201522948-10 Copies to include the following:

Self-test / Calibration ITA and Associated Hardware, PN TBD

NI PXIe-1085, 18 Slot 3U PXI Express Chassis, PN 781813-01

4 Module Bus Test Instruments, PN BI-411-00 4 Dual Port FC Simulyzer in a PCIe card format Single

Function, PN PXIe-FC4SF-4GB

Synchro/Resolver Processor, PN 65CS4-A2210E0- A2210E0-N

Fan Assembly, PN 201117900-10 2

MESS-4 2

MESS-7 2

ENVID GEN-510 with option 3&7 1

AB-9 Technical Drawing Package 1

Distribution Statement D: Distribution authorized to the Department of Defense and U.S. DoD contractors; Critical Technology, Export Controlled; 02/17/2016. Other requests for this document shall be referred to

AFLCMC/WNABA.

DESTRUCTION NOTICE: Destroy by any method that will prevent disclosure of contents or reconstruction of the document.

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et seq.) or the Export Administration Act of 1979 (Title 50, U.S.C., App. 2401 et seq.), as amended. Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoD Directive 5230.25

VPC ICA Module 510104136, 96 Pin Signal, VPC ICA signal pin 610110125; Mating Connector 510108126 Mating Contact 610110146 22 AWG shielded twisted pair

26" length Signals are connected to the red wire of the twisted pair while the adjacent GND is connected to the black wire The shield for the twisted pair is also connected to the GND

ICA Signal ICA Signal ICA Signal PIN Module Pin PIN Module Pin Pin Module Pin

1 33 0 17 GND 65 0 8 RA1

2 34 0 16 GND 66 0 7 RA0

3 0 25 GND 35 0 15 GND 67 0 6 TA1

4 0 24 SA1 36 0 14 GND 68 0 5 TA0

5 0 22 GND 37 0 13 GND 69 0 4 RX1

6 0 23 SA0 38 0 12 GND 70 0 3 RX0

7 39 0 11 GND 71 0 2 TX1

8 40 0 10 GND 72 0 1 TX0

9 1 1 TX0 41 1 10 GND 73

10 1 2 TX1 42 1 11 GND 74

11 1 3 RX0 43 1 12 GND 75 1 23 SA0

12 1 4 RX1 44 1 13 GND 76 1 22 GND

13 1 5 TA0 45 1 14 GND 77 1 24 SA1

14 1 6 TA1 46 1 15 GND 78 1 25 GND

15 1 7 RA0 47 1 16 GND 79

16 1 8 RA1 48 1 17 GND 80

17 49 2 17 GND 81 2 8 RA1

18 50 2 16 GND 82 2 7 RA0

19 2 25 GND 51 2 15 GND 83 2 6 TA1

20 2 24 SA1 52 2 14 GND 84 2 5 TA0

21 2 22 GND 53 2 13 GND 85 2 4 RX1

22 2 23 SA0 54 2 12 GND 86 2 3 RX0

23 55 2 11 GND 87 2 2 TX1

24 56 2 10 GND 88 2 1 TX0

25 3 1 TX0 57 3 10 GND 89

26 3 2 TX1 58 3 11 GND 90

27 3 3 RX0 59 3 12 GND 91 3 23 SA0

28 3 4 RX1 60 3 13 GND 92 3 22 GND

29 3 5 TA0 61 3 14 GND 93 3 24 SA1

30 3 6 TA1 62 3 15 GND 94 3 25 GND

31 3 7 RA0 63 3 16 GND 95

32 3 8 RA1 64 3 17 GND 96

J1A ICA Module Wire Run List

BTI #1 BTI #1 BTI #1

VPC ICA Module 510104136, 96 Pin Signal, VPC ICA signal pin 610110125; Mating Connector 510108126 Mating Contact 610110146 22 AWG shielded twisted pair

26" length Signals are connected to the red wire of the twisted pair while the adjacent GND is connected to the black wire The shield for the twisted pair is also connected to the GND

ICA Signal ICA Signal ICA Signal PIN Module Pin PIN Module Pin Pin Module Pin

1 33 0 17 GND 65 0 8 RA1

2 34 0 16 GND 66 0 7 RA0

3 0 25 GND 35 0 15 GND 67 0 6 TA1

4 0 24 SA1 36 0 14 GND 68 0 5 TA0

5 0 22 GND 37 0 13 GND 69 0 4 RX1

6 0 23 SA0 38 0 12 GND 70 0 3 RX0

7 39 0 11 GND 71 0 2 TX1

8 40 0 10 GND 72 0 1 TX0

9 1 1 TX0 41 1 10 GND 73

10 1 2 TX1 42 1 11 GND 74

11 1 3 RX0 43 1 12 GND 75 1 23 SA0

12 1 4 RX1 44 1 13 GND 76 1 22 GND

13 1 5 TA0 45 1 14 GND 77 1 24 SA1

14 1 6 TA1 46 1 15 GND 78 1 25 GND

15 1 7 RA0 47 1 16 GND 79

16 1 8 RA1 48 1 17 GND 80

17 49 2 17 GND 81 2 8 RA1

18 50 2 16 GND 82 2 7 RA0

19 2 25 GND 51 2 15 GND 83 2 6 TA1

20 2 24 SA1 52 2 14 GND 84 2 5 TA0

21 2 22 GND 53 2 13 GND 85 2 4 RX1

22 2 23 SA0 54 2 12 GND 86 2 3 RX0

23 55 2 11 GND 87 2 2 TX1

24 56 2 10 GND 88 2 1 TX0

25 3 1 TX0 57 3 10 GND 89

26 3 2 TX1 58 3 11 GND 90

27 3 3 RX0 59 3 12 GND 91 3 23 SA0

28 3 4 RX1 60 3 13 GND 92 3 22 GND

29 3 5 TA0 61 3 14 GND 93 3 24 SA1

30 3 6 TA1 62 3 15 GND 94 3 25 GND

31 3 7 RA0 63 3 16 GND 95

32 3 8 RA1 64 3 17 GND 96

J2A ICA Module Wire Run List

BTI #2 BTI #2 BTI #2

VPC ICA Module 510104136, 96 Pin Signal, VPC ICA signal pin 610110125; Mating Connector 510108126 Mating Contact 610110146

24 AWG

26" length J9A Pin SYNCRS Pin Signal

1 J1-1 SD Ch.1 S1 2 J1-2 SD Ch.1 S2 3 J1-20 SD Ch.1 S3 4 J1-21 SD Ch.1 S4 5 J1-3 SD Ch.1 RHI 6 J1-22 SD Ch.1 RLO 7 J1-4 SD Ch.2 S1 8 J1-5 SD Ch.2 S2 9 J1-23 SD Ch.2 S3 10 J1-24 SD Ch.2 S4 11 J1-6 SD Ch.2 RHI 12 J1-25 SD Ch.2 RLO 13 J1-8 DS Ch.1 S1 14 J1-9 DS Ch.1 S2 15 J1-27 DS Ch.1 S3 16 J1-28 DS Ch.1 S4 17 J1-10 DS Ch.1 RHI 18 J1-29 DS Ch.1 RLO 19 J1-11 DS Ch.2 S1 20 J1-12 DS Ch.2 S2 21 J1-30 DS Ch.2 S3 22 J1-31 DS Ch.2 S4 23 J1-13 DS Ch.2 RHI 24 J1-32 DS Ch.2 RLO

25 J1-7 RHI 1 OUT

26 J1-26 RLO 1 OUT

27 J1-18 SD Ch.1 Velocity Hi 28 J1-17 SD Ch.2 Velocity Hi 29 J1-16 DS Ch.1 Velocity Hi 30 J1-15 DS Ch.2 Velocity Hi 31 J1-33 SD Ch.1 Velocity Return 32 J1-34 SD Ch.2 Velocity Return 33 J1-35 DS Ch.1 Velocity Return 34 J1-36 DS Ch.2 Velocity Return 35 J1-19 Trigger - 36 J1-37 Trigger +

61 J2-1 SD Ch.3 S1 62 J2-2 SD Ch.3 S2 63 J2-20 SD Ch.3 S3 64 J2-21 SD Ch.3 S4 65 J2-3 SD Ch.3 RHI 66 J2-22 SD Ch.3 RLO 67 J2-4 SD Ch.4 S1 68 J2-5 SD Ch.4 S2 69 J2-23 SD Ch.4 S3 70 J2-24 SD Ch.4 S4 71 J2-6 SD Ch.4 RHI 72 J2-25 SD Ch.4 RLO 73 J2-8 DS Ch.3 S1 74 J2-9 DS Ch.3 S2 75 J2-27 DS Ch.3 S3 76 J2-28 DS Ch.3 S4 77 J2-10 DS Ch.3 RHI 78 J2-29 DS Ch.3 RLO 79 J2-11 DS Ch.4 S1 80 J2-12 DS Ch.4 S2 81 J2-30 DS Ch.4 S3 82 J2-31 DS Ch.4 S4 83 J2-13 DS Ch.4 RHI 84 J2-32 DS Ch.4 RLO

85 J2-7 RHI 1 OUT

86 J2-26 RLO 1 OUT

87 J2-18 SD Ch.3 Velocity Hi 88 J2-17 SD Ch.4 Velocity Hi 89 J2-16 DS Ch.3 Velocity Hi 90 J2-15 DS Ch.4 Velocity Hi 91 J2-33 SD Ch.3 Velocity Return 92 J2-34 SD Ch.4 Velocity Return 93 J2-35 DS Ch.3 Velocity Return 94 J2-36 DS Ch.4 Velocity Return 95 J2-19 Trigger -

96 J2-37 Trigger +

VPC ICA Module 510104134, 64 Pin Signal, VPC ICA signal pin 610110125; Mating Connector 510108101 Mating Contact 610110146

22 AWG

4 ft 9-pin D-sub J7A Position Instr Pin Module Signal

1 1 OP1

2 4 OP0

3 3 COM

4 2 CAN_L/Ext_RX Pins 2,7: Twisted shielded pair 5 7 CAN_H/Ext_TX 6 5 Shield

7 6 COM GND

8 8 NERR

9 9 Ext Vbat

10 1 OP1

11 4 OP0

12 3 COM

13 2 CAN_L/Ext_RX Pins 2,7: Twisted shielded pair 14 7 CAN_H/Ext_TX 15 5 Shield

16 6 COM GND

17 8 NERR

18 9 Ext Vbat

Port 1

Port 2

PVGA

Support Equipment Design Example - Cabling Wirelist.xlsx

PVGA analog cable same as AB-2 VPC ICA Module 510104149, 256 Pin Signal, Mating Connector 510108131 PVGA DVI cables will use COTS DVI cables to VPC PCB connector, 2 DVI channels

*Wire: All TP and sTP cable is 24 AWG unless otherwise noted (RG179)

From Instrument Connector Type Connector Signal Wire* To Slot # Pin # From Instrument Connector Type Connector Signal Wire* To Slot # Pin # D-Type 44pin J1-04 PCV GenRed + RG179 J10 1 J10 97 D-Type 44pin J1-19 PCV GenRed Ret RG179 J10 2 J10 98 D-Type 44pin J1-06 PCV Gen Green + RG179 J10 3 J10 99 D-Type 44pin J1-21 PCV Gen Green Ret RG179 J10 4 J10 100 D-Type 44pin J1-20 PCV Gen Blue Ret RG179 J10 5 J10 101 D-Type 44pin J1-05 PCV Gen Blue + RG179 J10 6 J10 102 D-Type 44pin J1-16 AcquisitionRed/X Ret RG179 J10 7 J10 103 D-Type 44pin J1-01 AcquisitionRed/X + RG179 J10 8 J10 104 D-Type 44pin J1-03 Acquisition Green/Y + RG179 J10 9 J10 105 D-Type 44pin J1-18 Acquisition Green/Y Ret RG179 J10 10 J10 106 D-Type 44pin J1-02 Acquisition Blue/Z + RG179 J10 11 J10 107 D-Type 44pin J1-17 Acquisition Blue/Z Ret RG179 J10 12 J10 108 D-Type 44pin J1-40 Raster Gen X - sTP J10 13 D-Type 100pin J13-63 Synthesized H Sync + TP J10 109 D-Type 44pin J1-10 Raster Gen X + sTP J10 14 D-Type 100pin J13-64 Synthesized H Sync - TP J10 110 D-Type 44pin J1-25 Raster Gen X Ret shield J10 15 D-Type 100pin J13-65 Detected Field + TP J10 111

J10 16 D-Type 100pin J13-66 Detected Field - TP J10 112 D-Type 44pin J1-11 Raster Gen Y + sTP J10 17 D-Type 100pin J13-71 Vertical Sync - TP J10 113 D-Type 44pin J1-26 Raster Gen Y Ret shield J10 18 D-Type 100pin J13-70 Vertical Sync + TP J10 114 D-Type 44pin J1-41 Raster Gen Y - sTP J10 19 SPARE 24 AWG J10 115

J10 20 SPARE 24 AWG J10 116

D-Type 44pin J1-42 Stroke Gen X - sTP J10 21 SPARE 24 AWG J10 117 D-Type 44pin J1-12 Stroke Gen X + sTP J10 22 SPARE 24 AWG J10 118 D-Type 44pin J1-27 Stroke Gen X Ret shield J10 23 D-Type 100pin J13-78 Horizontal Sync + TP J10 119

J10 24 D-Type 100pin J13-77 Horizontal Sync - TP J10 120 D-Type 44pin J1-13 Stroke Gen Y + sTP J10 25 D-Type 100pin J13-75 Vertical Sync - TP J10 121 D-Type 44pin J1-28 Stroke Gen Y Ret shield J10 26 D-Type 100pin J13-76 Vertical Sync + TP J10 122 D-Type 44pin J1-43 Stroke Gen Y - sTP J10 27 D-Type 100pin J13-73 External ‘Z’ Gate - TP J10 123

J10 28 D-Type 100pin J13-74 External ‘Z’ Gate + TP J10 124 D-Type 44pin J1-29 Stroke Gen Z Ret shield J10 29 D-Type 100pin J13-27 Trigger 24 AWG J10 125 D-Type 44pin J1-44 Stroke Gen Z - sTP J10 30 D-Type 100pin J13-50 PECL RTC Clock - TP J10 126 D-Type 44pin J1-14 Stroke Gen Z + sTP J10 31 D-Type 100pin J13-49 PECL RTC Clock + TP J10 127

J10 32 J10 128 SPARE sTP J10 33 D-Type 100pin J13-60 Remote Sense High[0] TP J10 129 SPARE shield J10 34 D-Type 100pin J13-57 Remote Sense Return[0] TP J10 130 SPARE sTP J10 35 D-Type 100pin J13-61 Remote Sense High[1] TP J10 131

J10 36 D-Type 100pin J13-58 Remote Sense Return[1] TP J10 132 D-Type 100pin J12-01 User Specified Pulse A + TP J10 37 D-Type 100pin J13-59 Remote Sense Return[2] TP J10 133 D-Type 100pin J12-02 User Specified Pulse A - TP J10 38 D-Type 100pin J13-62 Remote Sense High[2] TP J10 134

SPARE TP J10 39 J10 135

SPARE TP J10 40 J10 136

D-Type 100pin J12-05 User Specified Pulse C+ TP J10 41 D-Type 100pin J13-48 Remote Sense High[3] 24 AWG J10 137 D-Type 100pin J12-06 User Specified Pulse C - TP J10 42 D-Type 100pin J13-53 Remote Sense High[4] 24 AWG J10 138

SPARE TP J10 43 D-Type 100pin J13-54 Remote Sense High[5] 24 AWG J10 139

SPARE TP J10 44 J10 140

PVGA

Support Equipment Design Example - Cabling Wirelist.xlsx

D-Type 100pin J12-76 Horizontal Marker - TP J10 45 D-Type 100pin J13-41 +10V Reference Monitor - TP J10 141 D-Type 100pin J12-75 Horizontal Marker + TP J10 46 D-Type 100pin J13-40 +10V Reference Monitor + TP J10 142 D-Type 100pin J12-73 Vertical Marker - TP J10 47 J10 143 D-Type 100pin J12-74 Vertical Marker + TP J10 48 J10 144 D-Type 100pin J12-72 PCV Blanking 24 AWG J10 49 J10 145 D-Type 100pin J12-71 PCV Composite Sync 24 AWG J10 50 J10 146

J10 51 J10 147 J10 52 J10 148

D-Type 100pin J12-37 MultiLevel Signal 24 AWG J10 53 J10 149 D-Type 100pin J12-38 Gnd 24 AWG J10 54 J10 150 D-Type 100pin J12-39 Gnd 24 AWG J10 55 J10 151 D-Type 100pin J12-42 Gnd 24 AWG J10 56 J10 152 D-Type 100pin J12-35 Gnd 24 AWG J10 57 J10 153 D-Type 100pin J12-43 Gnd 24 AWG J10 58 J10 154 D-Type 100pin J12-44 Gnd 24 AWG J10 59 J10 155 D-Type 100pin J12-36 Blanking 24 AWG J10 60 J10 156 D-Type 100pin J12-40 Composite Video Gate + TP J10 61 J10 157 D-Type 100pin J12-41 Composite Video Gate - TP J10 62 J10 158 D-Type 100pin J12-33 Line Trigger 24 AWG J10 63 J10 159 D-Type 100pin J12-34 Field Trigger 24 AWG J10 64 J10 160

J10 65 J10 161 J10 66 J10 162 J10 67 J10 163 J10 68 J10 164

D-Type 100pin J12-45 External Trigger Ready + TP J10 69 J10 165 D-Type 100pin J12-46 External Trigger Ready - TP J10 70 J10 166 D-Type 100pin J12-47 Stroke User Specified Pulse A + TP J10 71 J10 167 D-Type 100pin J12-48 Stroke User Specified Pulse A - TP J10 72 J10 168 D-Type 100pin J12-49 Stroke User Specified Pulse B 24 AWG J10 73 J10 169

J10 74 J10 170 J10 75 J10 171 J10 76 J10 172 J10 77 J10 173

D-Type 100pin J12-63 Stroke External Trigger[0] + TP J10 78 J10 174 D-Type 100pin J12-64 Stroke External Trigger[0] - TP J10 79 J10 175 D-Type 100pin J12-56 Stroke External Trigger [1] 24 AWG J10 80 J10 176

J10 81 J10 177 D-Type 100pin J12-65 TTL_Vref 24 AWG J10 82 J10 178 D-Type 100pin J12-59 Stroke Gate 24 AWG J10 83 J10 179 D-Type 100pin J12-60 Stroke External Z Mod 24 AWG J10 84 J10 180 D-Type 100pin J13-42 Gnd 24 AWG J10 85 J10 181 D-Type 100pin J13-43 Gnd 24 AWG J10 86 J10 182 D-Type 100pin J13-44 Gnd 24 AWG J10 87 J10 183 D-Type 100pin J13-45 Gnd 24 AWG J10 88 J10 184 D-Type 100pin J13-46 Gnd 24 AWG J10 89 J10 185 D-Type 100pin J13-47 Gnd 24 AWG J10 90 J10 186 D-Type 100pin J13-25 Gnd 24 AWG J10 91 J10 187 D-Type 100pin J13-72 Gnd 24 AWG J10 92 J10 188

J10 93 J10 189 J10 94 J10 190

D-Type 100pin J13-32 PECL Sys Clock + TP J10 95 J10 191 D-Type 100pin J13-33 PECL Sys Clock - TP J10 96 J10 192

ATTI ENVID GEN-510

Video Generator

(A1A4A3)

ATTI ENVID GEN-510

Video Generator

(A1A4A3)

VPC ICA Module 510108112, 64 Pin Signal: Mating Connector 510108101 Mating Contact 610110146

6x RJ45 connectors, CAT5 patch cords

2 4 6 8 10 12 14 16 18 20 22 24 1 3 5 7 9 11 13 15 17 19 21 23

Port Instrument ICA Pinout

2 Control Panel (A1A4) 3 Blower 4 Unused 5 Unused 6 Unused 7 Unused 8 Unused 9 TPS Ethernet #1

10 TPS Ethernet #2 11 TPS Ethernet #3 12 TPS Ethernet #4 13 Unused 14 Unused 15 Unused 16 Unused 17 Unused 18 Unused 19 Unused 20 Unused 21 Unused 22 Unused 23 Unused 24 Unused

AB-9 Ethernet Switch Port Usage

Utility Panel (A1B1)

CAGE: 98752 DWG. NO.: 201117923 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117923.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

ASME Y14.38, ABBREVIATIONS AND ACRONYMS.

MIL-STD-130M IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

2. THIS DRAWING ESTABLISHES THE REQUIREMENTS FOR A COMMERCIAL OFF THE SHELF

QUARTER-TURN FASTENER.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A

SOURCE OF SUPPLY FOR THE ITEM(S).

4. QUALITY ASSURANCE. THE SUPPLIER SHALL VERIFY THAT UNITS SUPPLIED TO THIS

DRAWING CONFORM TO THE REQUIREMENTS SPECIFIED HEREIN.

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

WHICH WOULD AFFECT INTERCHANGEABILITY OR DEGRADE EITHER PERFORMANCE OR

RELIABILITY OF THE PRODUCT WITHOUT PRIOR NOTICE

CAGE: 98752 DWG. NO.: 201117923 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117923.docx Computer Generated

CONFIGURATION FOR CONTROL NUMBER -001:

DIMENSIONS ARE IN MM (INCHES)

SPECIFICATIONS FOR CONTROL NUMBER -001:

MATERIAL Steel RECEPTACLE STYLE Snap-in SIZE SERIES Medium Size TYPE Receptacle

CONFIGURATION FOR CONTROL NUMBER -002:

(IMAGES FOR REFERENCE ONLY)

SPECIFICATIONS FOR CONTROL NUMBER -002:

FINISH Zinc plate, Chromate plus sealer

SIZE SERIES Medium Size STUD HEAD STYLE Bail Style RA TYPE Stud STUD LENGTH (L) 16.4 mm (0.65 in) NOTE: Bail Stud must mate with Receptacle PN 201117923-001, CAGE 98752

CAGE: 98752 DWG. NO.: 201117923 REV – SHEET: 4

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117923.docx Computer Generated

CONFIGURATION FOR CONTROL NUMBER -003:

SPECIFICATIONS FOR CONTROL NUMBER -003:

MATERIAL Stainless Steel

TYPE Retainer

CONFIGURATION FOR CONTROL NUMBER -004:

Image is Bail Stud without Cover installed on left and installed on right

SPECIFICATIONS FOR CONTROL NUMBER -004:

Dimensions in mm, (inches).

NOTE: Bail Cover, must mate with Bail Style Stud PN 201117923-002, CAGE 98752

CAGE: 98752 DWG. NO.: 201117923 REV – SHEET: 5

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117923.docx Computer Generated

CONFIGURATION FOR CONTROL NUMBER -005:

SPECIFICATIONS FOR CONTROL NUMBER -005:

MATERIAL Nylon

TYPE Retainer Push-On

CONFIGURATION FOR CONTROL NUMBER -006:

SPECIFICATIONS FOR CONTROL NUMBER -006:

ACCESSORY TYPE Ejector Spring

TYPE Accessory

CAGE: 98752 DWG. NO.: 201117923 REV – SHEET: 6

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117923.docx Computer Generated

CONFIGURATION FOR CONTROL NUMBER -007:

SPECIFICATIONS FOR CONTROL NUMBER -007:

ACCESSORY TYPE Wear Washer COLOR Black

CAGE: 98752 DWG. NO.: 201117923 REV – SHEET: 7

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117923.docx Computer Generated

CONTROL

NUMBER

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117923-001 94222 82-35-309-56

Southco P.O. Box 0116 210 North Brinton Lake Rd.

Concordville, PA 19331

201117923-002 94222 82-15-500-16

Southco P.O. Box 0116 210 North Brinton Lake Rd.

Concordville, PA 19331

201117923-003 94222 82-32-201-20

Southco P.O. Box 0116 210 North Brinton Lake Rd.

Concordville, PA 19331

201117923-004 94222 82-2-B-000

Southco P.O. Box 0116 210 North Brinton Lake Rd.

Concordville, PA 19331

201117923-005 94222 82-32-301-12

Southco P.O. Box 0116 210 North Brinton Lake Rd.

Concordville, PA 19331

201117923-006 94222 43-13-1-24

Southco P.O. Box 0116 210 North Brinton Lake Rd.

Concordville, PA 19331

201117923-007 94222 82-46-101-41

Southco P.O. Box 0116 210 North Brinton Lake Rd.

Concordville, PA 19331

CAGE: 98752 DWG. NO.: 201117923 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117923.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

QUARTER-TURN FASTENER.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117923 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117923.docx Computer Generated

DIMENSIONS ARE IN MM (INCHES)

RECEPTACLE STYLE Snap-in

TYPE Receptacle

FINISH Zinc plate, Chromate plus sealer

SIZE SERIES Medium Size STUD HEAD STYLE Bail Style RA TYPE Stud STUD LENGTH (L) 16.4 mm (0.65 in) NOTE: Bail Stud must mate with Receptacle PN 201117923-001, CAGE 98752

CAGE: 98752 DWG. NO.: 201117923 REV – SHEET: 4

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117923.docx Computer Generated

MATERIAL Stainless Steel

TYPE Retainer

Image is Bail Stud without Cover installed on left and installed on right

NOTE: Bail Cover, must mate with Bail Style Stud PN 201117923-002, CAGE 98752

CAGE: 98752 DWG. NO.: 201117923 REV – SHEET: 5

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117923.docx Computer Generated

CONFIGURATION FOR CONTROL NUMBER -005:

SPECIFICATIONS FOR CONTROL NUMBER -005:

MATERIAL Nylon

TYPE Retainer Push-On

CONFIGURATION FOR CONTROL NUMBER -006:

SPECIFICATIONS FOR CONTROL NUMBER -006:

ACCESSORY TYPE Ejector Spring

CAGE: 98752 DWG. NO.: 201117923 REV – SHEET: 6

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117923.docx Computer Generated

CONFIGURATION FOR CONTROL NUMBER -007:

SPECIFICATIONS FOR CONTROL NUMBER -007:

ACCESSORY TYPE Wear Washer COLOR Black

CAGE: 98752 DWG. NO.: 201117923 REV – SHEET: 7

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117923.docx Computer Generated

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117923-001 94222 82-35-309-56

Southco P.O. Box 0116 210 North Brinton Lake Rd.

Concordville, PA 19331

201117923-002 94222 82-15-500-16

Southco P.O. Box 0116 210 North Brinton Lake Rd.

Concordville, PA 19331

201117923-003 94222 82-32-201-20

Southco P.O. Box 0116 210 North Brinton Lake Rd.

Concordville, PA 19331

201117923-004 94222 82-2-B-000

Southco P.O. Box 0116 210 North Brinton Lake Rd.

Concordville, PA 19331

201117923-005 94222 82-32-301-12

Southco P.O. Box 0116 210 North Brinton Lake Rd.

Concordville, PA 19331

201117923-006 94222 43-13-1-24

Southco P.O. Box 0116 210 North Brinton Lake Rd.

Concordville, PA 19331

201117923-007 94222 82-46-101-41

Southco P.O. Box 0116 210 North Brinton Lake Rd.

Concordville, PA 19331

SIZE

A

CAGE

CODE

98752

DWG NO.

200625645

REV

A

SCALE

NONE

SHEET:

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200625645_A.DOC Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

6FT UNIVERSAL POWER CORD. REPLACEMENT POWER CORD FOR PC, MONITOR,

PRINTER, SCANNER, ETC

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CONFIGURATION:

DIMENSIONS ARE NOMINAL

TYPICAL UNIVERSAL POWER CABLE

CAGE

CODE

98752

DWG NO.

200625645

REV

A

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200625645_A.DOC Computer Generated

SPECIFICATIONS:

UNIVERSAL POWER CORDS ARE DESIGNED TO WORK WITH MOST PCS, MONITORS,

SCANNERS, PRINTERS AND OTHER DEVICES THAT USE THE 3-PIN SHROUD POWER

CONNECTOR.

POWER CABLES SHOULD FEATURE A FULLY MOLDED DESIGN THAT PROVIDES MAXIMUM

DURABILITY AND LONG-LIFE.

CABLE TYPE: HEAVY-DUTY 18AWG

CONNECTORS: 3-PIN SHROUD FEMALE (IEC-320-C13) TO 3-PRONG GROUNDED PLUG MALE

(NEMA 5-15-P)

DESIGN: FEMALE CONNECTOR PLUGS DIRECTLY INTO DEVICE AND MALE CONNECTOR PLUGS

INTO STANDARD OUTLET

COMPATIBILITY: COMPUTERS, MONITORS, SCANNERS, PRINTERS, AND OTHER DEVICES

THAT USES A 3-PIN SHROUD POWER CONNECTOR

APPLICATION: REPLACEMENT POWER CORD

COLOR: BLACK

SIZE: 6FT IN LENGTH

WEIGHT: 0.43LBS

CERTIFICATION: UL LISTED

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

200625645 0VVY7 03130

CABLES TO GO

1501 Webster St. Dayton, OH 45404

200625645 92194 531B

ALPHA WIRE CORP

711 LIDGERWOOD AVENUE

ELIZABETH, NJ 07207-0711

CAGE CODE

98752

DWG NO.

200625952

REV

D

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200625952_D.DOC Computer Generated

LAN PATCH CABLE.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A SOURCE

OF SUPPLY FOR THE ITEM(S).

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

DIMENSIONS ARE SHOWN AS FEET

DIMENSIONS ARE NOMINAL.

CAGE CODE

98752

DWG NO.

200625952

REV

D

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200625952_D.DOC Computer Generated

FEATURES

THE DASH NUMBER OF THE CONTROL NUMBER EQUALS THE LENGTH IN FEET

COLOR BLACK

50" GOLD-PLATED MODULAR PLUGS

FLEXIBLE LOW-PROFILE SNAGLESS STRAIN RELIEF

500 MHZ

24 AWG UTP CABLE

ETL TESTED & VERIFIED

ANSI/TIA-568-B.2-1 CAT 6 INDUSTRY STANDARDS

PRE-TERMINATED WITH WE8W RJ45 PLUGS

COMPLIANT WITH TIA/EIA-568-B.2-1, FCC 68, EN50173:2002

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

200625952-01 4UV57 2288

MONOPRICE INC

11701 6

TH

STREET

RANCHO CUCAMONGA, CA 91730

200625952-03 4UV57 2295

MONOPRICE INC

11701 6

TH

STREET

RANCHO CUCAMONGA, CA 91730

200625952-05 4UV57 3426

MONOPRICE INC

11701 6

TH

STREET

RANCHO CUCAMONGA, CA 91730

200625952-07 4UV57 2302

MONOPRICE INC

11701 6

TH

STREET

RANCHO CUCAMONGA, CA 91730

200625952-14 4UV57 2309

MONOPRICE INC

11701 6

TH

STREET

RANCHO CUCAMONGA, CA 91730

200625952-14 1JN02 601-737791-14

MOUSER ELECTRONICS INC

1000 N MAIN ST

MANSFIELD TX 76063-1514

200625952-25 4UV57 2316

MONOPRICE INC

11701 6

TH

STREET

RANCHO CUCAMONGA, CA 917304

CAGE: 98752 DWG. NO.: 200626295 REV A SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200626295_A.DOC Computer Generated

2. THIS DRAWING ESTABLISHES THE REQUIREMENTS FOR A COMMERCIAL OFF

THE SHELF UNIVERSIAL CONNECTOR HOUSING AND CONTACTS.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT

TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED

AVAILABILITY AS A SOURCE OF SUPPLY FOR THE ITEM(S).

4. QUALITY ASSURANCE. THE SUPPLIER SHALL VERIFY THAT UNITS SUPPLIED TO

THIS DRAWING CONFORM TO THE REQUIREMENTS SPECIFIED HEREIN.

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE

DRAWING WHICH WOULD AFFECT INTERCHANGEABILITY OR DEGRADE EITHER

PERFORMANCE OR RELIABILITY OF THE PRODUCT WITHOUT PRIOR NOTICE.

6. FOR CONNECTOR LISTING WITH MATING PRODUCT REFERENCE TABLE 1.

TYPICAL TWO PIN MALE CONNECTOR (P/N 1-480698-0)

CONTROL NUMBER 200626295-001

DIMENSIONS ARE SHOWN AS MILIMETERS

CAGE: 98752 DWG. NO.: 200626295 REV A SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200626295_A.DOC Computer Generated

TYPICAL TWO PIN FEMALE CONNECTOR (P/N 1-480699-0)

CONTROL NUMBER 200626295-002

DIMENSIONS ARE SHOWN AS INCHES [mm].

CAGE: 98752 DWG. NO.: 200626295 REV A SHEET: 4

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200626295_A.DOC Computer Generated

TYPICAL FOUR PIN MALE CONNECTOR (P/N 1-480702-0)

CONTROL NUMBER 200626295-003

DIMENSIONS ARE SHOWN AS MILIMETERS.

CAGE: 98752 DWG. NO.: 200626295 REV A SHEET: 5

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200626295_A.DOC Computer Generated

TYPICAL FOUR PIN FEMALE CONNECTOR (P/N 1-480703-0)

CONTROL NUMBER 200626295-004

DIMENSIONS ARE SHOWN AS MILIMETERS.

CAGE: 98752 DWG. NO.: 200626295 REV A SHEET: 6

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200626295_A.DOC Computer Generated

TYPICAL 12-CKT MALE CONNECTOR (P/N 1-480708-0)

CONTROL NUMBER 200626295-015

DIMENSIONS ARE SHOWN AS MILLIMETERS [INCHES]

CAGE: 98752 DWG. NO.: 200626295 REV A SHEET: 7

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200626295_A.DOC Computer Generated

TYPICAL 12-CKT FEMALE CONNECTOR (P/N 1-480709-0)

CONTROL NUMBER 200626295-016

DIMENSIONS ARE SHOWN AS MILLIMETERS.

CAGE: 98752 DWG. NO.: 200626295 REV A SHEET: 8

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200626295_A.DOC Computer Generated

TYPICAL 15-CKT MALE CONNECTOR (P/N 1-480710-0)

CONTROL NUMBER 200626295-005

DIMENSIONS ARE SHOWN AS MILLIMETERS [INCHES]

CAGE: 98752 DWG. NO.: 200626295 REV A SHEET: 9

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200626295_A.DOC Computer Generated

TYPICAL 15-CKT FEMALE CONNECTOR (P/N 1-480711-0)

CONTROL NUMBER 200626295-006

DIMENSIONS ARE SHOWN AS MILLIMETERS

CAGE: 98752 DWG. NO.: 200626295 REV A SHEET: 10

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200626295_A.DOC Computer Generated

TYPICAL CONNECTOR PIN (P/N 350218-7)

CONTROL NUMBER 200626295-007

DIMENSIONS ARE SHOWN AS INCHES

TYPICAL CONNECTOR PIN (P/N 350536-7, P/N 350538-7)

CONTROL NUMBER 200626295-008, 200626295-017

DIMENSIONS ARE SHOWN AS MILLIMETERS

CAGE: 98752 DWG. NO.: 200626295 REV A SHEET: 11

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200626295_A.DOC Computer Generated

TYPICAL CONNECTOR PIN (P/N 350689-1, P/N 350689-2 , P/N 350690-2)

CONTROL NUMBER 200626295-009, 200626295-010 and 200626295-011

DIMENSIONS ARE SHOWN AS INCHES.

TYPICAL CONNECTOR PIN (P/N 350922-3)

CONTROL NUMBER 200626295-012

CAGE: 98752 DWG. NO.: 200626295 REV A SHEET: 12

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200626295_A.DOC Computer Generated

TYPICAL CONNECTOR PIN (P/N 640309-3)

CONTROL NUMBER 200626295-013

TYPICAL CONNECTOR PIN (P/N 640310-3)

CONTROL NUMBER 200626295-014

CAGE: 98752 DWG. NO.: 200626295 REV A SHEET: 13

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200626295_A.DOC Computer Generated

CONNECTOR SPECIFICATIONS:

LOCK TYPE POSITIVE LOCK

COLOR NATURAL

MATERIAL NYLON UL 94 V-2

PART NUMBER NUMBER OF PINS

NUMBER OF CONNECTOR PINS 1-480698-0 2

CROSS REFERENCE TO 1-480699-0 2

CONNECTOR PART NUMBER 1-480702-0 4

1-480703-0 4 1-480710-0 15 1-480711-0 15 1-480708-0 12

1-480709-0 12

HOUSING 0.250 INCH CENTERLINE RECEPTACLE (PLUG)

MOUNT FREE OR PANEL

CENTERLINE, MATRIX (MM [IN]) 6.35 [.250]

HOUSING TYPE RECEPTACLE (CAP)

CONTACT DIAMETER (MM [IN]) 2.13 [0.084]

SEALABLE YES

CURRENT RATING 19 AMPS (NOT HIGH CURRENT)

VOLTAGE RATING 600 VAC

CONTACT DIAMETER 0.084 INCHES

INDUSTRY STANDARDS ROHS COMPLIANT,ELV COMPLIANT

CAGE: 98752 DWG. NO.: 200626295 REV A SHEET: 14

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200626295_A.DOC Computer Generated

PIN SPECIFICATIONS:

CONNECTOR SERIES: UNIVERSAL MATE-N-LOK

CURRENT RATING: 19 AMPS

VOLTAGE RATING: 600 VAC

SOLDER TAIL CONTACT

PLATING: SELECT GOLD

WIRE RANGE: P/N 350218-7 20-14 AWG

P/N 350536-7 20-14 AWG

P/N 350538-7 20-14 AWG

P/N 350689-2 24-18 AWG

P/N 350690-2 24-18 AWG

P/N 350922-3 12-10 AWG

P/N 640309-3 12-10 AWG

P/N 640310-3 12-10 AWG

CONTACT MATERIAL: BRASS

ROHS/ELV COMPLIANCE ROHS COMPLIANT, ELV COMPLIANT

ELECTRICAL SPECIFICATIONS:

Dielectric Withstanding Voltage 5.0 KVAC or 5.0 KVDC between adjacent circuits Insulation Resistance 1000 Mega ohms minimum initial between adjacent circuits Voltage Rating 600 V AC or DC Contact Insertion Force 5.0 lb. max. per contact Contact Retention 15 lb. min. per contact Durability 50 cycles, mating and un mating

CAGE: 98752 DWG. NO.: 200626295 REV A SHEET: 15

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200626295_A.DOC Computer Generated

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

200626295-001 00779 1-480698-0

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

200626295-002 00779 1-480699-0

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

200626295-003 00779 1-480702-0

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

200626295-004 00779 1-480703-0

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

200626295-005 00779 1-480710-0

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

200626295-006 00779 1-480711-0

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

200626295-007 00779 350218-7

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

200626295-008 00779 350536-7

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

200626295-009 00779 350689-1

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

200626295-010 00779 350689-2

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

200626295-011 00779 350690-2

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

200626295-012 00779 350922-3

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

200626295-013 00779 640309-3

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

200626295-014 00779 640310-3

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

200626295-015 00779 480708-0

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

200626295-016 00779 480709-0

TYCO ELECTRONICS CORPORATION

2800 FULLING MILL RD BLDG-38

MIDDLETOWN, PA 17057-3142

CAGE: 98752 DWG. NO.: 200626295 REV A SHEET: 16

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 200626295_A.DOC Computer Generated

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

200626295-017 00779 350538-7

TYCO ELECTRONICS CORPORATION

CAGE: 98752 DWG. NO.: 201117931 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117931.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

COVER, TERMINAL BLOCK.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117931 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117931.docx Computer Generated

(IMAGE FOR REFERENCE ONLY)

Cover for 3/8" Center-to-Center, 3 Circuit, 600 & 300 VAC/VDC Terminal Block

NOTE: Cover must function with PN 201117835, CAGE 98752

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117931 0KVE6 7527K827

McMASTER-CARR SUPPLY CO

6100 FULTON INDUSTRIAL BLVD

ATLANTA, GA 30336

CAGE: 98752 DWG. NO.: 201117932 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117932.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

SWITCH, PUSHBUTTON.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117932 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117932.docx Computer Generated

CAGE: 98752 DWG. NO.: 201117932 REV – SHEET: 4

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117932.docx Computer Generated

ELECTRICAL:

Category Metal Pushbutton Switch with Latching Action Actuator Type Round Button Circuit SPST Current Rating 12A (AC) Voltage Rating 250VAC Illumination Type, Color LED, Green Illumination Voltage (Nominal) 24 VDC Mounting Type Panel Mount, Front Switch Function On-Off Termination Style Quick Connect - .187” (4.7mm) Type Vandal Resistant, Illuminated RoHS Status RoHS Compliant Panel Cutout Dimensions Circular – 19.10mm Dia Switch Function On-Off

MATERIAL:

Actuator Stainless Steel Housing Stainless Steel

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117932 01EL2 486-1449-ND

Digi-Key Corporation 701 Brooks Avenue South Thief River Falls, MN 56701

CAGE: 98752 DWG. NO.: 201117933 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117933.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

switch, pushbutton.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117933 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117933.docx Computer Generated

CAGE: 98752 DWG. NO.: 201117933 REV – SHEET: 4

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117933.docx Computer Generated

ELECTRICAL:

Category Pushbutton Switch Actuator Type Square Button Circuit SPST Current Rating 2A (AC), 100mA (DC) Voltage Rating 125VAC Voltage Rating 24VDC Mounting Type Panel Mount, Front Switch Function On-Off Termination Style Solder Lug Type Standard RoHS Status RoHS Compliant Panel Cutout Dimensions Circular - 13.60mm Dia Switch Function On-Off

Actuator polyamide 6/6 Housing thermoplastic UL94-V0 Contacts silver, gold plated (std)

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117933 3G3K6 IPC1SAD2

APEM Components, Inc.

63 Neck Road Haverhill, MA 01835-0788

CAGE: 98752 DWG. NO.: 201117935 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117935.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

Terminal Block, Spec.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117935 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117935.docx Computer Generated

Wd 1.13” Ht 0.53” Lg 2.06” Wire size 22-12 Screw terminal size #6-32 Mount hole diameter 0.18”

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117935 0KVE6 7527K43

McMASTER-CARR SUPPLY CO

CAGE: 98752 DWG. NO.: 201117936 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117936.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

DUST CAP.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117936 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117936.docx Computer Generated

Rigid Plastic Caps

Fits OD 2” Inside Ht. 15/32” Color Black

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117936 0KVE6 9567K18

McMASTER-CARR SUPPLY CO

CAGE: 98752 DWG. NO.: 201117937 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117937.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

INDICATOR, AUDIO.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117937 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117937.docx Computer Generated

Product Category Audio Indicators & Alerts Technology Piezo Sound Pressure Level 91 dBA Tone Fast Pulse (Beep) Voltage rating 220 VDC/VAC Current Rating 16 mA Termination Style Pin Dimensions 42.5 mm L x 42.5 mm W X 42 mm H Frequency 2800 Hz +/- 500 Hz Mounting Panel

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117937 1JN02 AI-4328-P-FP250-R

Mouser Electronics 1000 North Main Street Mansfield, TX 76063

CAGE: 98752 DWG. NO.: 201117938 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117938.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

FILTER ELEMENT, AIR CONDITIONING.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117938 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117938.docx Computer Generated

Washable Aluminum filter replacement Fits 4"

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117938 00843 AFLTR4AL

HOFFMAN ENGINEERING CO

2100 HOFFMAN WAY

ANOKA, MN 55303

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

SCREW CUFF, 2.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117939 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117939.docx Computer Generated

2.00” I.D.

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117939 4ECU9 DC384

Flexaust

1510 Armstrong Road Warsaw, IN 46580

CAGE: 98752 DWG. NO.: 201117939 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117939.docx Computer Generated

CAGE: 98752 DWG. NO.: 201117940 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117940.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

BAFFLE, AIRFLOW, ELECTRONIC EQUIPMENT.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117940 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117940.docx Computer Generated

Filter Type Exhaust Material Plastic External Depth 11mm External Heigth 160mm Fan Size 160 x 187 Mm External Width 187 mm Fixing Centers 162 mm Color Light Gray

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117940 00843 TEP4

Hong Kong office:

Unit A 22/F, Full Commercial

Centre, 573 Nathan road, KL, Hong Kong

CAGE: 98752 DWG. NO.: 201117941 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117941.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

CLAMP, REPAIR, PIPE.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117941 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117941.docx Computer Generated

Stainless Steel type 304

Pipe size 2” x 2” Lg. 3” Max Pressure @72 degree F: 15 psi Temp Range 0 to 180 degree F

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117941 0KVE6 6820K22

McMASTER-CARR SUPPLY CO

CAGE: 98752 DWG. NO.: 201117942 REV A SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117942_A.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

HOSE, FLEXIBLE.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117942 REV A SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117942_A.docx Computer Generated

TEMPATURE RANGE -20 TO 200 F

CONSTRUCTION POLYOLEFIN WALL AND HELIX

DIAMETER 2 INCHES

LENGTH 15 FEET

COMPRESSION 3:1 RATIO

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117942 4ECU9 STA-FLEX

ATLANTA RUBBER & HYDRAULICS, INC.

DBA CAROLINA RUBBER &

HYDRAULICS

1000 MARBLE MILL CIR NW

MARRIETA, GA 30060

CAGE: 98752 DWG. NO.: 201117943 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117943.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

CONNECTOR, POWER INLET.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117943 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117943.docx Computer Generated

FILTER TYPE POWER ENTRY (FILTERED/UNFILTERED)

SERIES SR (6 AMP)

FILTERED NO

TYPE OF CONNECTOR IEC 320/C-14

GENDER MALE

CURRENT RATING 15 A

VOLTAGE (UP TO) 250 VAC

I/O COMBINATION IEC – ¼” FASTON

ROHS/ELV COMPLIANCE YES

CAGE: 98752 DWG. NO.: 201117943 REV – SHEET: 4

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117943.docx Computer Generated

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117943 00779 6ESRM-3

TYCO ELECTRONICS CORPORATION

CAGE: 98752 DWG. NO.: 201117944 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117944.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

FLOWMETER.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117944 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117944.docx Computer Generated

Accuracy ±1.0% of reading Repeatability ±0.25% Body 304/316 stainless steel Rotor 17-4 PH SS Bearings 440C stainless steel Output 30 mV p-p sinewave min.

Electrical 2-wire connector included Max Temp. Range 267 to 232°C (-450 to 450°F) Maximum Pressure Drop Gas density in lb/ft3 x 4 (psid)

Model No.

Price Linear Range(ACFM)

Nominal K- Factor(p/ACF)

Psi Length E nd Connectors

Weight

FTB-939 1335 15 to 250 230 1500 4.75” 2” 13 lbs

CAGE: 98752 DWG. NO.: 201117944 REV – SHEET: 4

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117944.docx Computer Generated

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117944 29907 FTB-939

OMEGA Engineering Inc.

One Omega Drive

P.O. Box 4047 Stamford, CT 06907

CAGE: 98752 DWG. NO.: 201117945 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117945.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

DISPLAY, COLOR, PROGRAMMABLE.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117945 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117945.docx Computer Generated

CAGE: 98752 DWG. NO.: 201117945 REV – SHEET: 4

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117945.docx Computer Generated

DESCRIPTION DIGITAL PANEL METER (DPM)

ACCURACY +/- 0.5 DEG. C, 0.03% OF READING

A/D CONVERSION DUAL SLOPE

READING RATE 3 SAMPLES/SEC

DISPLAY 4 DIGIT, 9 SEG. LED (COLORS SET AS RED, AMBER

OR GREEN AT PROCESS SET POINTS)

POLARITY UNIPOLAR

INPUT TYPES THERMOCOUPLE (TC), RTD, ANALOG VOLTAGE,

ANALOG CURRENT

TC LEAD RESISTANCE 100 OHM

TC TYPES J, K, T, E, R, S, B, C, N, L

RTD INPUT 100/500/1000 OHM PLATINUM SENSOR; 2,3, OR 4

WIRE

VOLTAGE INPUTS 0 TO 100MV, 0 TO 1V, OR 0 TO 10VDC

INPUT IMPEDANCE 10 MOHM ( 100MV RANGE)

1 MOHM (1 OR 10VDC RANGE)

CURRENT INPUT 0-20 MA

TEMP. STABILITY 50 PPM/ DEG. C

CMRR 120DB

NMRR 60 DB

CONTROL BUS/PROGRAMMING ETHERNET, 802.3 10BASE T (TCP/IP, ARP, HTTPGET),

RS-232, RS-422, OR RS-485

OUTPUTS 2 (SPDT) ALARM; SET TRIPS ALARM 1, ALARM 2

SET POINT ADJUST PROGRAMMABLE: -1999 TO 9999 COUNT

OFFSET ADJ. -1999 TO 9999 COUNT

READING RATE 3 SAMPLES / SEC

DECIMAL SELECTION NONE, .1, .01, OR .001

STEP RESPONSE 0.7 SEC FOR 99.9% OF READING

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117945 29907 CNI852

OMEGA Engineering Inc.

One Omega Drive

Stamford, CT 06907

CAGE: 98752 DWG. NO.: 201117946 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117946.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

POWER SUPPLY.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

6. CONFIGURATION ITEM: DO NOT CHANGE WITHOUT SYSTEM ENGINEER APPROVAL.

CAGE: 98752 DWG. NO.: 201117946 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117946.docx Computer Generated

Technical/Catalog Information LS25-15

Vendor TDK-LAMBDA AMERICAS INC Category Power Supplies - External/Internal (Off-Board)

Number of Outputs 1 Power (Watts) 25W

Voltage - Output 15V Voltage - Input 88 ~ 264VAC

Power Supply Type Switching (Closed Frame) Output - 1 @ Current (Max) 15 VDC @ 1.7A Output - 2 @ Current (Max) - Output - 3 @ Current (Max) - Output - 4 @ Current (Max) -

Mounting Type Chassis Mount

Size / Dimension 3.1" L x 2" W x 1.1" H (78.7mm x 50.8mm x 27.9mm)

Operating Temperature -25°C ~ 70°C Efficiency 83%

Applications Commercial Approvals CE, EN, IEC, UL

CAGE: 98752 DWG. NO.: 201117946 REV – SHEET: 4

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117946.docx Computer Generated

Line Regulation - Load Regulation -

Power (Watts) - Max 26W Lead Free Status Lead Free

RoHS Status RoHS Compliant

Other Names

LS25 15

LS2515

285 1885 ND

2851885ND

285-1885

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117946 576B8 LS25-15

Digi-Key Corporation

701 Brooks Ave South Thief River Falls, MN 56701

CAGE: 98752 DWG. NO.: 201117948 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117948.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

BYPASS BLOWER.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117948 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117948.docx Computer Generated

DIMENSIONS ARE IN MILLIMETER

INCHES

CAGE: 98752 DWG. NO.: 201117948 REV – SHEET: 4

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117948.docx Computer Generated

PRODUCT CATEGORY: BYPASS BLOWER

STAGES 1

MAX. VACUUM (in H2O) 26 MAX. PRESSURE (in H2O) 29

MAX. FLOW RATE (CFM) 226

INLET/OUTLET DIA. (inches) 2.75/2.5

INPUT VOLTAGE 120VAC / 60HZ

WEIGHT (lbs) 6 POWER (Watts) 800

TEMPERATRE, OPERATING 0 TO 50 DEG. C

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201117948 4A887 119105-01

AMETEK AEROSPACE & DEFENSE

627 LAKE ST.

KENT, OH 44240

CAGE: 98752 DWG. NO.: 201117951 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117951.docx Computer Generated

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

SIGNAL CONDITIONER.

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

CAGE: 98752 DWG. NO.: 201117951 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201117951.docx…