FA811722Q0002_CDRL_Exhibit 1.pdf

PWS Attachment 1

Exhibit A

Contract Data Requirements List (CDRL)

CDRL DID Description Frequency A001 DI-PSSS-81534A Teardown Deficiency Report As Required A002 DI-MISC-81832 Counterfeit Prevention Plan As Required A003 DI-MGMT-80969 Production Surge Plan As Required A004 DI-SESS-80639E Engineering Change Proposal (ECP) As Required A005 DI-PSSS-81656B Bill of Materials (BOM) for Logistics and Supply Chain Risk Management As Required

A006 DI-MGMT-81803A Item Unique Identification (IUID) Marking Plan As Required

A007 DI-MGMT-81838 Commercial Asset Visibility (CAV) Reporting As Required

A008 DI-MGMT-80441D Government Property Inventory Report Annually

A009 DI-PSSS-81995A Contract Depot Maintenance (CDM) Production Report Monthly

DATA ITEM DESCRIPTION

Title: TEARDOWN DEFICIENCY REPORT

Number: DI-PSSS-81534A Approved Date: 20160608

AMSC Number: F9670 Limitation: N/A

DTIC Applicable: No GIDEP Applicable: No

Preparing Activity: 11 (AFLCMC/EZSC) Project Number: PSSS-2015-024

Applicable Forms: N/A

Use/Relationship: The Teardown Deficiency Report provides a factual narrative analysis of a deficiency which has been noted on equipment.

a. This Data Item Description (DID) is applicable when contractors are responsible for maintaining custodial records for government property being repaired.

b. This DID contains the format, content and intended use information for the data deliverable resulting from the work task described in the solicitation.

c. This DID supersedes DI-ALSS-81534.

Requirements:

1. Reference documents. None.

2. Format. The Teardown Deficiency Report shall be in the contactor’s format.

3. Content. This report shall include an analysis of the deficiency which includes cause of failure, recommended corrective action and recommendations for actions to prevent recurrence of the failure/deficiency, and the applicable category of the failure defined as follows:

a. Workmanship and non-conformance. Any deficiency (e.g., physical, chemical, electrical, functional) noted in materiel which is attributed to non-conformance to applicable specifications, drawing, standards, or Technical Order (TO); or workmanship during manufacture, repair modification or maintenance.

b. Material failure. The failure of an end item which was attributable to neither the repair nor the manufacturing process, but was due to an unpredictable failure of an internal component or sub-assembly.

c. No defect found/could not duplicate: Investigation of the exhibit revealed no deficiency.

Equipment conforms to specifications and TO standards and procedures.

d. Technical data, deficiency: Technical data (including TOs, drawings, and work specifications) was deficient or inadequate so as to cause the deficiency/failure on the item.

e. Field induced deficiency. Deficiency confirmed by the investigation to have been caused by operator error, i.e., wrong voltage applied, misaligned, maladjusted, mishandling, or not used for intended purpose.

DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

Source: https://assist.dla.mil -- Downloaded: 2016-06-27T17:52Z Check the source to verify that this is the current version before use.

DI-PSSS-81534A

f. Maintenance deficiency. An unfavorable characteristic of an item that impedes the accomplishment of maintenance operations which results in excessive maintenance operations and/or in excessive maintenance man-hour consumption.

g. Design deficiency. A condition that limits or prevents the use of material for purpose intended or required where the material meets all other specifications.

h. Handling or shipping deficiency. A deficiency induced by improper handling or shipping, i.e., improper packaging, which prohibits the use for intended purpose.

i. Packaging specifications inadequate - not complied with. Unsatisfactory conditions including item damage resulting from improper packaging.

End of DI-PSSS-81534A.

Source: https://assist.dla.mil -- Downloaded: 2016-06-27T17:52Z

TITLE: COUNTERFEIT PREVENTION PLAN

Number: DI-MISC-81832 Approval Date: 20110121 AMSC Number: 9181 Limitation:

DTIC Applicable: No GIDEP Applicable: No Office of Primary Responsibility: NRO Applicable Forms: N/A

Use/Relationship: The Counterfeit Prevention Plan will be used by the procurement activity to determine and evaluate the effectiveness of the contractor’s counterfeit protection plan and award fee.

a. This Data Item Description contains the format and content preparation instructions for the data product generated by the specific and discrete task requirements delineated in the statement of work.

b. This DID is related to Parts, Materials and Processes Selection List (PMPSL).

c. This DID is related to “As Designed” and “As Built” Parts List.

d. The Counterfeit Prevention Plan will be updated as counterfeiting methods evolve to include any new indicators, as well as new prevention processes needed (either discovered directly or provided by the Government).

Requirements:

1. The Counterfeit Prevention Plan shall be in contractor format and shall include the following, as a minimum:

a. Procurement practices and procedures to include procurement of all parts and materials from original qualified parts/materials equipment manufacturer (OEM) or it franchised/authorized distributor.

b. Procurement practices and internal processes used for exceptions to buying from OEM or OEM franchised distributors in cases where items are no longer available including a process to qualify/certify non-OEM parts & materials.

c. Monitoring procedures to include the delivery of test results from random sampling and supply chains surveillance that does not assume any source is safe to identify possible penetration of OEM supply chain.

d. Training/certification program for receiving inspectors.

e. Process to verify counterfeit.

DI-MISC-81832

- 2 -

f. Processes to identify, store, and report counterfeit parts.

g. Process to ensure subcontracts contain the following requirements (As a minimum):

(1) Requirements to procure only from Original Equipment Manufacturer (OEM) or OEM franchised distributors

(2) Procurement practices and internal processes used for exceptions to buying from OEM or OEM franchised distributors including a process to qualify/certify non-OEM parts & materials obtained

(3) Requirements to monitor supply (including delivery of test results from random sampling and supply chain surveillance that does not assume any source is safe) to identify possible penetration of OEM supply chain

(4) Training/certification program for receiving inspectors

(5) Process to verify counterfeit

(6) Processes to identify, store, and report counterfeit parts.

(7) Notification procedure (tailored to specific sub-contractor based on following Notification Procedure)

h. Self-audit of internal processes.

i. Monitor processes at all subcontractor levels processes and verify compliance through on-site audits.

j. Notification Procedure:

(1) Step 1: The contractor shall quarantine all suspect products pending further direction. The contractor shall provide a statement, with problem description, justifying why this is considered suspect and how it was detected. The contractor shall NOT notify the supplier that the items are suspected as being counterfeit items. However, consultation with the OEM is authorized. Make certain the parts and all members of the lot procured for use on this contract are stored in correct environmental controls. These parts need to be protected as evidence.

(2) Step 2: Contractors that identify suspect items shall immediately notify their customer that is the next link toward the prime contractor.

Notification shall be passed up the customer chain until reaching the prime contractor. The prime contractor shall immediately notify the cognizant Contracting Officer (CO) and Contracting Office Technical Representative (COTR) of all suspect items identified.

DI-MISC-81832

- 3 -

(3) Step 3: The contractor shall make certain that the original documentation is secured as evidence and maintain any and all documentation associated with the part to include:

a. Part information such as part identifying number, lot date code, manufacturer information and originator/point of contact information

b. Any information reflecting part procurement/acquisition traceability which should include a copy of the purchase order, any and all correspondence between the buyer and the supplier to include: e-mails, records of phone conversations and paper letters of correspondence

c. Part documentation from the purported original manufacturer, distributors and suppliers (certificate of compliance and certificate of conformance)

d. All visual examination and physical analysis/testing results and the technical data package showing that the parts passed the required screening and qualification tests

e. List of company products affected

(4) Step 4: Determine that the part is or is not counterfeit (Usually accomplished as part of root cause analysis of non-conforming parts and/or materials)

(5) Step 5: If the parts are found to be counterfeit, they shall be isolated and controlled pending direction from law enforcement.

(6) Step 6: The contractor shall provide any additional required information to the government’s investigation team

END OF DI-MISC-81832

Source: http://assist.dla.mil -- Downloaded: 2019-02-14T15:58Z

Source: http://assist.dla.mil -- Downloaded: 2019-02-14T15:58Z

Title: ENGINEERING CHANGE PROPOSAL (ECP)

Number: DI-SESS-80639E Approval Date: 20200211

AMSC Number: N10140 Limitation: N/A

DTIC Applicable: No GIDEP Applicable: No

Preparing Activity: NM Project Number: SESS-2020-003

Applicable Forms: DD Form 1692, Engineering Change Proposal (ECP)

Use/relationship: An Engineering Change Proposal (ECP) provides the documentation in which the engineering change is described and specifies how the proposed change will be implemented.

a. This DID contains the format, content, and intended use information for the data deliverable resulting from the work task described in EIA-649-1 and the principles of EIA-649 (Copies of these standards are available online at www.sae.org or from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel 877-606-7323 [inside USA and Canada] or 724-776-4970 [outside

USA]).

b. This DID may be used in conjunction with DI-SESS-80642, Notice of Revision (NOR). A requirement for NORs and Specification Change Notices (SCN) should be contractually imposed in conjunction with this DID.

c. This DID supersedes DI-SESS-80639D.

d. An electronic version of DD Form 1692, Engineering Change Proposal (ECP), is available online at https://www.esd.whs.mil/dd/.

Requirements:

1. Reference Documents. The applicable issue of the documents cited herein, including their approval dates and dates of any applicable amendments, notices, and revisions, shall be as specified in the contract.

2. Format. The ECP shall be in one of the following formats:

a. DD Form 1692, Engineering Change Proposal (ECP),

b. The schema required by the Acquirer’s Integrated Digital Environment (IDE), or

c. The Supplier’s preferred format.

3. Content. The ECP shall contain all the information required by DD Form 1692.

End of DI-SESS-80639E

DISTRIBUTION STATEMENT A. Approved for public release. Distribution is unlimited.

Source: http://assist.dla.mil -- Downloaded: 2020-03-16T20:28Z

Check the source to verify that this is the current version before use.

http://www.sae.org/ http://www.esd.whs.mil/dd/

Title: BILL OF MATERIALS (BOM) FOR LOGISTICS AND SUPPLY CHAIN RISK

MANAGEMENT

Number: DI-PSSS-81656B Approval Date: 20160901

AMSC Number: N9724 Limitation: N/A

DTIC Applicable: N/A GIDEP Applicable: No

Preparing Activity: SA Project Number: PSSS-2016-021

Applicable Forms: N/A

Use/relationship: The Bill of Materials (BOM) will provide information that can be used to establish the production status of parts used in a system. The BOM will also provide Diminishing

Manufacturing Sources and Material Shortages (DMSMS) management essential information that enables the identification, forecasting, mitigation, and management of Hardware and

Software obsolescence as a part of the Department of Defense (DoD) Program Manager’s Total

System Life Cycle Management responsibilities. The data will be used in DMSMS forecasting tools to allow for standard and efficient sharing of information on common items.

The BOM will also provide logisticians and supply chain risk managers with additional data they require to ensure supportability requirements and supply chain risks are identified or mitigated during the development of a system.

This Data Item Description (DID) contains the format, content, and intended use of information for the data product resulting from the work task described by the contract.

The data may be obtained during any program life cycle phase.

This DID supersedes DI-PSSS-81656A.

1. Format. The BOM shall be in a format similar to that of Figure 1.

2. Content. The BOM shall contain all of the information specified in Figure 1, with the path to the system level identified using the part/Next Higher Assembly method detailed in the table.

All fields shall be included. Fields which do not require data shall be left blank. The information shall be included to the lowest indenture level (component level) specified in the contract

Source: http://assist.dla.mil -- Downloaded: 2022-04-15T18:05Z

DI-PSSS-81656B

FIGURE – 1 Table 1: Field Definitions and Instructions

Field Name Definition Notes and Instructions Data Type

OEM Part

Number

The part number assigned by the Original Equipment

Manufacturer (OEM). This may be the same as the

Manufacturer’s number but more often than not it is different. Sometimes referred to the Configuration Part

Number or the Drawing Number

Required. Referred to as the

“Referenced Part” hereafter

Alphanumeric

OEM Name The full legal name of the entity that is providing the referenced part to the government. Sometimes referred to as the Prime Integrator or Prime

Required Alphanumeric

OEM CAGE Commercial and Government Entity (CAGE) code of the OEM

Required Alphanumeric (5)

OEM’s Address The physical address of the part’s OEM, including country

Required Alphanumeric

OEM’s Website The web address of the part’s OEM Required when the OEM has a website

Alphanumeric

OEM’s Facility

Clearance Level

The level of security clearance the OEM’s facility holds Required Alphanumeric

(None, Confidential, Secret, Top Secret)

Revision

Designator

The designator of the revision of the referenced part Required if assigned Alphanumeric

Software /

Firmware Version

The designator assigned to the version of software / firmware used on the referenced part

Required for all parts containing software or firmware

Alphanumeric

Indenture Level A number that represents the specific level of the top down structure specified on the Bill of Materials

Starts with the top level as one Numeric

Reference

Designator

A reference designator identifies the referenced part.

ASME Y14.44-2008 and IEEE-315-1975 provide details for the proper configuration and use of reference designators.

Required if assigned Alphanumeric

Find Number Find number refers to the ordinal number that gives an ID tag to the referenced part in a parts list (list of materials, bill of materials).

Required if assigned Alphanumeric

NHA Part

Number

The OEM Part Number of the referenced part’s parent (Next Higher Assembly (NHA)). If the referenced part is software or firmware then the

NHA is the item the software is used on

Required for all parts except the top level assembly

Alphanumeric

NHA CAGE CAGE code of the OEM of the NHA Required for all parts except the top level assembly

Alphanumeric (5)

Nomenclature The name or designation of the referenced part Required for all parts Alphanumeric

Quantity The count of the referenced part per NHA Required for all parts Numeric

NSN National Stock Number (NSN) of the referenced part Required if item has NSN assigned

Alphanumeric

COG Cognizance (COG) Code: A two-part alphanumeric designator used by the Navy to provide supply management information

Required if assigned Alphanumeric

Manufacturer’s

Part Number

The part number assigned by the actual manufacturer of the referenced item. This number will be used to monitor the part for obsolescence issues

Required (may be the same as the referenced part if the part is manufactured by the OEM)

Alphanumeric

Manufacturer’s

Name

The full legal name of the entity that actually manufacturers the referenced part

Required Alphanumeric

Manufacturer’s

CAGE

The CAGE code of the entity that actually manufacturers the referenced part

Required Alphanumeric (5)

Manufacturer’s

Address

The physical address of the part’s manufacturer, including country

Required Alphanumeric

Manufacturer’s

Website

The web address of the part’s manufacturer Required when the manufacturer has a website

Alphanumeric

Manufacturer’s

Facility Clearance

Level

The level of security clearance the manufacturer’s facility holds

Required Alphanumeric

(None, Confidential, Secret, Top Secret)

Alternate For The OEM part number of the item the referenced part is the alternate for

Required if the referenced part is an alternate to another pat in the

BOM

Alphanumeric

Assembly Type Identifies whether the item is Commercial Off the Shelf

(COTS), Non-Developmental Item (NDI), or

Developmental Item (DI)

Required if the part is an assembly considered COTS, NDI, or DI. See the definitions section of 48 CFR 2.101 for definitions.

Alphanumeric

(COTS, NDI, or

DI)

Batteries Indicates whether an item contains batteries. Required. If the referenced part contains batteries and is a subassembly, its NHA should indicate that it also contains batteries

Yes / No

Service Bulletin

Applicability

Information required to subscribe to service bulletin updates to the part’s software or hardware

Required if the part will have service bulletins issued against it

Alphanumeric

3. Media Requirement: The BOM shall be provided as an electronically editable, machine-readable, Comma Separated Values

(CSV) text file with alphanumeric fields enclosed in double quotation marks.

End of DI-PSSS-81656B

Title: ITEM UNIQUE IDENTIFICATION (IUID) MARKING PLAN

Number: DI-MGMT-81803A Approval Date: 20200311 AMSC Number: F10164 Limitation: N/A DTIC Applicable: No GIDEP Applicable: No Preparing Activity: 16 (AFMC/A4NL) Project Number: MGMT-2019-028 Applicable Forms: N/A

Use/Relationship: The Item Unique Identification (IUID) Marking Plan details the Contractor’s strategy to execute marking requirements identified in the Government contract document(s) and Defense Federal Acquisition Regulation Supplement (DFARS).

The purpose of the IUID Marking Plan is for the Contractor to identify and define, in detail, their IUID marking process and procedures to meet Government contract requirements in accordance with Military Standard (MIL- STD) -130, Identification Marking of U.S. Military Property, for item marking; MIL-STD-129, Military Marking for Shipment and Storage, for packaging marking; and the DoD Guide to Uniquely Identifying Items Assuring Valuation, Accountability and Control of Government Property. (Copies of MIL-STD-130 and MIL-STD-129 are available online at: https://quicksearch.dla.mil/qsSearch.aspx, and a copy of the Department of Defense (DoD) Guide is available online at https://dodprocurementtoolbox.com/site-pages/overview-implementation.)

The IUID Marking Plan shall include item and packaging marking requirements and methodology, encoding correct data, data management, facilities use, marking equipment, data carrier symbols, registration, quality assurance, validation, verification, registration of items being marked, and a master schedule to help the Contractor manage marking activities in a cost effective and timely manner.

a. This Data Item Description (DID) contains the format, content, and intended use information for the data deliverable resulting from the work task described in the contract document(s).

b. This DID is used on any contract that requires delivery of an IUID Marking Plan to the Government.

c. This DID supersedes DI-MGMT-81803.

Requirements:

1. Reference documents. The applicable issue of the documents cited herein, including their approval dates and dates of any applicable amendments, notices, or revisions, shall be as specified in the contract.

2. Format. The IUID Marking Plan shall be in contractor-developed, Government-approved format. Spreadsheet format shall be used when marking multiple items with IUID.

3. Content. The IUID Marking Plan shall include the following, except when the data matrix mark containing IUID data is embedded in a data label or plate and is already documented in an approved drawing. In such cases, the requirements indicated with an asterisk (*) shall be omitted when describing the label or plate marking:

3.1 List the applicable reference document(s).

3.2 List the end items and components marked with IUID under the requirements of the contract document(s), including DFARS 252.211-7003. (Copies of DFARS clause 252.211-7003 can be obtained online at:

https://www.acquisition.gov/content/regulations.)

Source: http://assist.dla.mil -- Downloaded: 2022-07-08T19:56Z Check the source to verify that this is the current version before use.

https://quicksearch.dla.mil/qsSearch.aspx https://dodprocurementtoolbox.com/site-pages/overview-implementation https://www.acquisition.gov/content/regulations

DI-MGMT-81803A

3.3 Describe the marking methodology, which shall include the following:

3.3.1* Marking method used for each item to be marked (e.g., by direct marking on the item’s surface, or by indirect marking on a plate or label attached to the item). The marking method may differ for each item.

3.3.1.1* When direct part marking is used, describe the methods used to apply the direct part mark.

3.3.2 Item Marking Specifications:

3.3.2.1 When engineering drawings incorporating the IUID marking requirement exist, list and associate each drawing with the items requiring IUID marking. If not, enter “N/A.”

3.3.2.2 Describe the following aspects of Machine Readable Mark generation:

3.3.2.2.1 IUID construct to be encoded in the data matrix. (e.g., Construct 1, Construct 2, or a specific, DoD-recognized IUID equivalent, which can be found at:

http://www.acq.osd.mil/dpap/pdi/uid/iuid_equivalents.html)

3.3.2.2.1.1 When using Construct 1, state whether the item’s Original Equipment Manufacturer (OEM) serial number is part of the Unique Item Identifier (UII), and, if not, how the serial number component of the UII is established.

3.3.2.2.2 Type of Enterprise Identifier (EID) in the mark. (e.g., Commercial and Government Entity (CAGE) code, Data Universal Numbering System (DUNS), DoD Activity Address Code (DoDAAC), or Global Standards One (GS1)).

3.3.2.2.3 The data elements to be encoded in the data matrix symbol, other than those from which the UII is derived, if any.

3.3.2.3* Describe the characteristics of the label or data plate:

3.3.2.3.1* Type of material used for the label or plate. (e.g., aluminum, polyacrylic, metal foil, polyester, polyvinyl, aluminum foil, stainless steel, etc.)

3.3.2.3.2* Method used to mark the data on the label or plate for each item to be marked. (e.g., laser etching, thermal transfer on polyester label stock, photo anodized aluminum plate, etc.)

3.3.2.3.3* Size of the label or plate, including units. (e.g., length, width, thickness, etc.)

3.3.2.3.4* Shape of the label or plate. (e.g., circle, square, rectangle, rounded corners, etc.)

3.3.2.3.5 Illustrate the label or plate to show the Human Readable Information (HRI) and the location of the data matrix.

3.3.2.3.6* Location of the label or plate on the item, include an illustration or photo, if possible.

3.3.2.3.7* Human readable lettering. (e.g., serif, font, font size, color, etc.)

3.3.2.3.8* Attachment method. (e.g., adhesive, screws, rivets, etc.)

3.3.2.3.9* Type of adhesive used, if applicable.

Source: http://assist.dla.mil -- Downloaded: 2022-07-08T19:56Z http://www.acq.osd.mil/dpap/pdi/uid/iuid_equivalents.html

3.3.3 The process for marking legacy parts and Government Furnished Property (GFP).

3.3.4 How Unit Packs, Intermediate Containers, and Exterior Containers shall be marked in compliance with the DFARS 252.211-7003; MIL-STD-129; International Organization for Standardization (ISO)/International Electrotechnical Commission (IEC) 15434, Information Technology – Automatic Identification and data capture techniques – Syntax for high-capacity ADS media; and American National Standards Institute (ANSI) MH10.8.2, Data Identifier and Application Identifier Standard. (Copies of ISO/IEC 15434 can be obtained at:

https://www.iso.org. Copies of ANSI MH10.8.2 can be obtained at: https://webstore.ansi.org.):

3.3.4.1 Portable Data File (PDF) 417 two (2) dimensional (2D) stacked linear barcode symbol format.

3.3.4.1.1 For data elements encoded in a PDF417 on a unit pack’s packaging, the actual item’s data shall be provided, when possible. State the data elements to be encoded in the mark. Include a readable PDF417 barcode with the data encoded correctly; specify the data string encoded in the mark, including control characters; or both.

3.3.4.1.2 For data elements encoded in a PDF417 barcode on an Exterior Container, state the data elements to be encoded in the mark. Include a readable PDF417 barcode with correctly encoded data;

specify the data string encoded in the mark, including control characters; or both. The actual item’s data shall be provided, when possible.

3.3.5 The Quality Assurance (QA) processes for the item mark, which ensure the item’s Machine Readable Information (MRI) complies with MIL-STD-130.

3.3.5.1 Validation and verification. Include a description of the specific equipment used to perform validation and verification, and the sampling technique when 100% verification and validation is not planned.

3.3.5.2 Format and frequency. Identify a format and frequency for contractually-required reporting of validation and verification results, to include a pass or fail rating for each mark verified and each mark validated.

3.3.5.3 State where validation and verification is to be performed (i.e., contractor facility or sub-contractor facility).

3.3.5.4 Describe the process used for replacing any marks that fail a QA check.

3.3.5.5 State contract data item numbers from the Contract Data Requirements List (CDRL) that pertain to QA on IUID marks.

3.3.6 The packaging mark QA processes:

3.3.6.1 Describe packaging mark validation. In the absence of packaging mark validation software, a manual comparison of the encoded data string to the requirements of MIL-STD-129 shall be included.

3.3.7 Facilities and marking equipment to be employed:

3.3.7.1 State where item labels or plates are created (i.e., contractor or sub-contractor facility).

3.3.7.2 Describe marking equipment used, to include any potential environmental impacts of the marking process and procedures designed to mitigate the risks of potential environmental impacts.

Source: http://assist.dla.mil -- Downloaded: 2022-07-08T19:56Z Check the source to verify that this is the current version before use.

https://www.iso.org/ https://webstore.ansi.org/

3.4 Describe data management processes:

3.4.1 Identify the actions required to register the pedigree data for the items marked with IUID in the DoD IUID Registry, in accordance with DFARS 252.211-7003.

3.4.2 When the contract requires non-warranty repair of items designated for IUID, describe the processes to:

3.4.2.1 Assess the readability of the data matrix marks on the items received that are marked with a data matrix.

3.4.2.1.1 Re-mark items with unreadable data matrix marks, which encode the original UIIs. The descriptions shall address the following: Will the complete data plate be remade? Will an additive label be applied? Will the original data matrix be obliterated?

3.4.2.2 Determine whether unmarked items were previously assigned a UII, and, if the mark is detached from the item, ensure that the remarked item uses the original UII.

3.4.2.3 Assign and mark a UII on DoD-owned items requiring IUID, but not previously assigned a UII.

3.4.2.3.1 Register new UIIs using the Repairable Receiving Report in Wide Area Work Flow (WAWF).

3.5 Provide the Master Schedule for IUID marking, to include:

3.5.1 Target dates for:

3.5.1.1 First submission of the marking plan.

3.5.1.2 Government approval of the IUID marking plan.

3.5.1.3 Commencement of marking (first item).

3.5.1.4 First item acceptance by Government.

3.5.1.5 Any other key events.

3.5.2 When marking is contingent on non-recurring engineering actions or is to be sub-contracted, state the projected schedules related to those processes.

End of DI-MGMT-81803A

Source: http://assist.dla.mil -- Downloaded: 2022-07-08T19:56Z

Title: COMMERCIAL ASSET VISIBILITY (CAV) REPORTING

Number: DI-MGMT-81838 Approval Date: 20110914 AMSC Number: N9211 Limitation: N/A DTIC Applicable: N/A GIDEP Applicable: N/A Office of Primary Responsibility: SA/WSS 071.02 Applicable Forms: N/A

Use/relationship:

The Commercial Asset Visibility (CAV) application provides a web-based, automated method of tracking Government owned reparable assets as they flow through the repair cycle at the contractor's repair facility. The main purpose of CAV is to provide an inventory management system for reparable assets while they are at commercial repair vendors. CAV on the World Wide Web allows the contractor to report transactions as they occur. These transactions automatically update the CAV database. An integrated, relational database allows the commercial repair vendors to access their repair data to produce all of the required status and activity reports.

This Data Item Description (DID) contains the format and content preparation instructions for the data product generated by the specific and discrete task requirement, as delineated in the contract.

1. Format. The CAV System transactions are processed via the World Wide Web. Input formats and methodology are defined in the Contract Statement of Work.

2. Content. The Contractor reporting shall contain the following transactions, status code changes and report types, as described in the Contract Statement of Work:

A. Receipt of Asset

1) On Contract

2) Not on Contract

3) Procurement

4) "A" Condition

5) Rotable Pool

6) Loaned Asset

B. Inductions C. Items Awaiting Parts D. Re-inductions E. Completions F. Shipments

Source: http://assist.dla.mil -- Downloaded: 2022-05-19T16:50Z

DI-MGMT-81838

G. Bulk Shipments H. Proof of Shipment I. Items that are Beyond Economic Repair (BER) J. Survey/Scrap Items K. Reversals L. Report of Discrepancies M. Print DD Form 1348's N. Print Material Movement Documents O. Print CAV Inventory Labels P. Print Item Action Reports Q. Print Repair History Reports R. Print Condition Code Reports S. Print Awaiting Parts Report T. Print Proof of Shipment Reports U. Perform Item Maintenance V. Print Report of Discrepancies (RODs) W. Add and Delete Carriers

3. End of DI-MGMT-81838.

Source: http://assist.dla.mil -- Downloaded: 2022-05-19T16:50Z

Title: Government Property (GP) Inventory Report Number: DI-MGMT-80441D Approval Date: 20200609 AMSC Number: 10184 Limitation: N/A DTIC Applicable: No GIDEP Applicable: No Preparing Activity: MDA Project Number: MGMT-2020-012 Applicable Forms: None

Use/Relationship: The Government Property (GP) Inventory Report enables the contractor to periodically provide to the Department of Defense (DoD) Service or Agency an inventory listing of GP (i.e., both Government Furnished Property (GFP) and Contractor Acquired Property (CAP)) in the contractor’s possession (to include subcontractors) by contract.

This Data Item Description (DID) is applicable to all contracts where GP will be furnished by the Government (i.e., GFP) or acquired, fabricated, or otherwise provided by a contractor (i.e., CAP) in performance of a contract.

This DID contains the format, content, and intended use information for the data deliverable resulting from the work task described in the solicitation.

This DID supersedes DI-MGMT-80441C.

1. Reference documents. None.

2. Format. The report shall be in an electronic .xls or .xlsx compatible format.

3. Content. The report shall contain the following column headers (i.e., data fields):

A. Contract Number B. Agency or Service Asset Identification Number (GFP Only) C. Contractor Asset Identification Number D. Item Description E. Manufacturer Part Number F. Manufacturer Model Number G. Manufacturer Serial Number H. National Stock Number (NSN) (if applicable) I. Quantity J. Unit of Measure K. Unit Acquisition Cost L. Unique Item Identifier (if registered in the Item Unique Identification (IUID) Registry;

GFP only) M. Asset Location N. Asset Sub-Location (if applicable) O. Type of Government Property (i.e., Government Furnished Property (GFP) or

Contractor Acquired Property (CAP) P. Classification of Government Property (i.e., Communication Security (COMSEC), Equipment (EQP), Material (MAT), Special Test Equipment (STE), or Special Tooling

Source: http://assist.dla.mil -- Downloaded: 2020-12-07T16:17Z

DI-MGMT-80441D

(ST))

Q. Date of Last Physical Inventory R. Federal Condition Code

END OF DI-MGMT-80441D

Source: http://assist.dla.mil -- Downloaded: 2020-12-07T16:17Z

Title: CONTRACT DEPOT MAINTENANCE (CDM) PRODUCTION REPORT

Number: DI-PSSS-81995 Approved Date: 20150904

AMSC Number: 9576 Limitation: N/A

DTIC Applicable: No GIDEP Applicable: No

Preparing Activity: 11 (AFMC/A4) Project Number: PSSS-2015-009

Applicable Forms: N/A

Use/Relationship: The Contract Depot Maintenance (CDM) Production Report is a two-part report which provides the Government with monthly maintenance production figures, status and accountability of assets at the contractor facility, performance to schedule, anticipated production for the next month, and a summary of unresolved problems at the end of the report period.

a. This Data Item Description (DID) contains the format, content and preparation instructions for the data product generated by the specific and discrete task requirement as delineated in the contract.

b. This DID may be used on any depot level maintenance contract.

Requirements:

1. Format. This report shall be provided in the format of Table I.

2. Content. The report shall consist of two parts and contain the following information:

a. Part I:

(1) As of date: The year, month and day applicable to the report. Data must be through the end of the month.

(2) Block 1, Issuing/Procuring Agency. Include address and Point of Contact.

(3) Block 2, Contractor and activity address code (AAC). The name of the business and the DoDAAC assigned to your business for shipment of material.

(4) Block 3, Contract number and Program or Weapon System supported.

(5) Block 4, Government item manager or technical Point of Contact.

(6) Block A, Item identification. The National Stock Number (NSN), A-1 is the Federal Supply Class (FSC) and A-2 is the National Item Identification Number (NIIN) of the item being reported.

(7) Block B, Delivery/Call Order number. When the awarded contract is a call/delivery order type, this is the applicable order number. When an item is awarded on more than one order, it is repeated for each order until completed. If the current report completes the call, the word “completed” will be added.

(8) Block C, The contract line item number (CLIN). The CLIN assigned to the NSN in the contract.

DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

Source: http://assist.dla.mil -- Downloaded: 2022-05-19T16:51Z

DI-PSSS-81995

(9) Block D, The document/voucher number the item was received under. The document number listed on the shipping documentation the item was received against.

(10) Block E, Quantity on contract or call. E-1 is the quantity of the end items to be repaired on each call/delivery order or contract quantity when orders do not apply. E-2 is the total quantity scheduled for repair cumulative to date.

(11) Block F, Reparables received. Number of reparable items received for repair. F-1 is the quantity of reparables received during the report month. F-2 is the quantity of reparables received cumulative from the start of the contract through report month.

(12) Block G, Reparables inducted into repair during report month.

(13) Block H, Reparables on hand. Number of reparables on hand waiting induction into repair.

(14) Block I, Quantity produced. The quantity produced during the month.

(15) Block J, Serviceables shipped. Serviceables shipped from repair facility. J-1 is the serviceables shipped through report month. J-2 is serviceables shipped cumulative from start of contract.

(16) Block K, Serviceables on hand. The quantity of serviceables on hand awaiting shipping action.

(17) Block L, Quantity condemned. The quantity condemned. L-1 is the quantity condemned during report month. L-2 is the quantity condemned cumulative from start of contract.

(18) Block M, Forecast to complete. The quantity of items scheduled to be produced next month.

(19) Block N, Report date. Enter date of report.

b. Part II, Production problems. Report shall be in narrative format and only required if:

(1) Previous reports production forecast was not shipped.

(2) Current forecast does not equal contract scheduled quantity.

(3) Contract anticipates a problem in the near future.

TABLE I. Contract Depot Maintenance (CDM) Production Report format.

CONTRACT DEPOT MAINTENANCE (CDM) PRODUCTION REPORT Month and As-Of Date

(YYYYMMDD)

Part I

1. ISSUED BY: 2. CONTRACTOR AND ACTIVITY ADDRESS CODE 3. CONTRACT NUMBER/PRGM/WS 4. GOVERNMENT ITEM MANAGER OR TECHNICAL POC

DURING REPORT PERIOD/TOTAL TO DATE

A.

ITEM

IDENTIFICATION

B.

DELIVERY/

CALL NUMBER

C.

CONTRACT

LINE ITEM

(CLIN)

D.

DOCUMENT/

VOUCHER

NUMBER

E.

QTY ON

CONTRACT

OR

DO/CALL

F.

REPARABLES

RECEIVED

G.

QTY

IND TO

WORK

H.

REPS ON

HAND

I.

QTY

PROD

J.

SERVICEABLES

SHIPPED

K.

SERV ON

HAND

L.

QTY

CONDEMNED

M.

FORECAST PROD

N.

REPORT DATE

FSC NIIN

1 2 1 2 3 1 2 1 2 1 2

Part II, Production Summary

End of DI-PSSS-81995.