solicitatioon.doc

Section SF 1449 - CONTINUATION SHEET

Niagara Meter Strain Gage Flow Meters Pa

FFP

Niagara Meter Strain Gage Flow Meters Part Number VL-1.25-A0S5k with MIL connector and no transmitter. Stainless steel housing, 37 degree flare tube male ends, linear configuration and rated for 5000 pounds per square inch (gage) working pressure. For use with MIL-L-7808 oil, 0 to 30 gallons per minute flow rate, and -65 to +300 degrees Fahrenheit operating temperature. Accuracy of plus or minus 1.0% of rate maximum, repeatability of plus or minus 0.15% of rate maximum, and minimum response time of 0.34 milliseconds. Three (3) Flow Meter calibrations. One calibration at a viscosity of 22.8 centipoises utilizing MIL-L-7808 hydraulic oil. One calibration at a viscosity of 10.6 centipoises utilizing MIL-L-7808 hydraulic oil. One calibration at a viscosity of 6.2 centipoises utilizing MIL-L-7808 hydraulic oil.

FOB: Destination

BRAND NAME/SOLE SOURCE: SS

PURCHASE REQUEST NUMBER: F3YCFH3037AG01

SIGNAL CODE: A

NET AMT

MIL-L-7808 Hydraulic Oil calibration set

MIL-L-7808 Hydraulic Oil calibration setup at a viscosity of 22.8 centipoises.

FOB: Destination

BRAND NAME/SOLE SOURCE: SS

NET AMT

MIL-L-7808 Hydraulic Oil calibration set

MIL-L-7808 Hydraulic Oil calibration setup at a viscosity of 10.6 centipoises.

FOB: Destination

BRAND NAME/SOLE SOURCE: SS

NET AMT

MIL-L-7808 Hydraulic Oil calibration set

MIL-L-7808 Hydraulic Oil calibration setup at a viscosity of 6.2 centipoises.

FOB: Destination

BRAND NAME/SOLE SOURCE: SS

NET AMT

INSPECTION AND ACCEPTANCE TERMS

Supplies/services will be inspected/accepted at:

DELIVERY INFORMATION

76 CMXG/MX

ARNOLD & C AVE BLDG 200 STE 201

TINKER AFB OK 73145-9103

405-734-0226

FOB: Destination

F3YCFH

F3YCFH

F3YCFH

F3YCFH

CLAUSES INCORPORATED BY REFERENCE

CLAUSES INCORPORATED BY FULL TEXT

52.252-2 CLAUSES INCORPORATED BY REFERENCE (FEB 1998)

This contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at this/these address(es):

HTTP://FARSITE.HILL.AF.MIL

(End of clause)

252.212-7001 CONTRACT TERMS AND CONDITIONS REQUIRED TO IMPLEMENT STATUTES OR EXECUTIVE ORDERS APPLICABLE TO DEFENSE ACQUISITIONS OF COMMERCIAL ITEMS (MAR 2013)

(a) The Contractor agrees to comply with the following Federal Acquisition Regulation (FAR) clause which, if checked, is included in this contract by reference to implement a provision of law applicable to acquisitions of commercial items or components.

X 52.203-3, Gratuities (APR 1984) (10 U.S.C. 2207).

(b) The Contractor agrees to comply with any clause that is checked on the following list of Defense FAR Supplement clauses which, if checked, is included in this contract by reference to implement provisions of law or Executive orders applicable to acquisitions of commercial items or components.

(1) X 252.203-7000, Requirements Relating to Compensation of Former DoD Officials (SEP 2011) (Section 847 of Pub. L. 110-181).

(2) ____ 252.203-7003, Agency Office of the Inspector General (DEC 2012)(section 6101 of Pub. L. 110-252, 41 U.S.C. 3509).

(3) ____ 252.205-7000, Provision of Information to Cooperative Agreement Holders (DEC 1991) (10 U.S.C. 2416).

(4) ____ 252.219-7003, Small Business Subcontracting Plan (DoD Contracts) (AUG 2012) (15 U.S.C. 637).

(5) ____ 252.219-7004, Small Business Subcontracting Plan (Test Program) (JAN 2011) (15 U.S.C. 637 note).

(6)(i) X 252.225-7001, Buy American and Balance of Payments Program (DEC 2012) (41 U.S.C. chapter 83, E.O. 10582).

(ii) ____ Alternate I (OCT 2011) of 252.225-7001.

(7) X 252.225-7008, Restriction on Acquisition of Specialty Metals (MAR 2013) (10 U.S.C. 2533b).

(8) X 252.225-7009, Restriction on Acquisition of Certain Articles Containing Specialty Metals (MAR 2013) (10 U.S.C. 2533b).

(9) ____ 252.225-7012, Preference for Certain Domestic Commodities (FEB 2013) (10 U.S.C. 2533a).

(10) ____ 252.225-7015, Restriction on Acquisition of Hand or Measuring Tools (JUN 2005) (10 U.S.C. 2533a).

(11) X 252.225-7016, Restriction on Acquisition of Ball and Roller Bearings (JUN 2011) (Section 8065 of Pub. L. 107-117 and the same restriction in subsequent DoD appropriations acts).

12) ____ 252.225-7017, Photovoltaic Devices (DEC 2012) (Section 846 of Pub. L. 111-383).

13)(i) ____ 252.225-7021, Trade Agreements (DEC 2012) (19 U.S.C. 2501-2518 and 19 U.S.C. 3301 note).

(ii) ____ Alternate I (OCT 2011) of 252.225-7021.

(iii) ____ Alternate II (OCT 2011) of 252.225-7021.

(14) ____ 252.225-7027, Restriction on Contingent Fees for Foreign Military Sales (APR 2003) (22 U.S.C. 2779).

(15) ____ 252.225-7028, Exclusionary Policies and Practices of Foreign Governments (APR 2003) (22 U.S.C. 2755).

(16)(i) ____ 252.225-7036, Buy American Act—Free Trade Agreements—Balance of Payments Program (DEC 2012) (41 U.S.C. chapter 83 and 19 U.S.C. 3301 note).

(ii) ____ Alternate I (JUN 2012) of 252.225-7036.

(iii) ____ Alternate II (NOV 2012) of 252.225-7036.

(iv) ____ Alternate III (JUN 2012) of 252.225-7036.

(v) ____ Alternate IV (NOV 2012) of 252.225-7036.

(vi) ____Alternate V (NOV 2012) of 252.225-7036.

(17) ____ 252.225-7038, Restriction on Acquisition of Air Circuit Breakers (JUN 2005) (10 U.S.C. 2534(a)(3)).

(18) ____ 252.225-7039, Contractors Performing Private Security Functions (JUN 2012) (Section 862 of Pub. L. 110-181, as amended by section 853 of Pub. L. 110-417 and sections 831 and 832 of Pub. L. 111-383).

(19) ____ 252.226-7001, Utilization of Indian Organizations, Indian-Owned Economic Enterprises, and Native Hawaiian Small Business Concerns (SEP 2004) (Section 8021 of Pub. L. 107-248 and similar sections in subsequent DoD appropriations acts).

(20) ____ 252.227-7013, Rights in Technical Data--Noncommercial Items (FEB 2012), if applicable (see 227.7103-6(a)).

(21) ____ 252.227-7015, Technical Data—Commercial Items (DEC 2011) (10 U.S.C. 2320).

(22) ____ 252.227-7037, Validation of Restrictive Markings on Technical Data (JUN 2012), if applicable (see 227.7102-4(c)))(10 U.S.C. 2321).

(23) X 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports (MAR 2008) (10 U.S.C. 2227).

(24) ____ 252.237-7010, Prohibition on Interrogation of Detainees by Contractor Personnel (NOV 2010) (Section 1038 of Pub. L. 111-84)

(25) ____ 252.237-7019, Training for Contractor Personnel Interacting with Detainees (SEP 2006) (Section 1092 of Pub. L. 108-375).

(26) ____ 252.243-7002, Requests for Equitable Adjustment (DEC 2012) (10 U.S.C. 2410).

(27) ____ 252.246-7004, Safety of Facilities, Infrastructure, and Equipment For Military Operations (OCT 2010) (Section 807 of Pub. L. 111-84).

(28) ____ 252.247-7003, Pass-Through of Motor Carrier Fuel Surcharge Adjustment to the Cost Bearer (SEP 2010) (Section 884 of Pub. L. 110-417).

(29)(i) ____ 252.247-7023, Transportation of Supplies by Sea (MAY 2002) (10 U.S.C. 2631).

(ii) ____ Alternate I (MAR 2000) of 252.247-7023.

(iii) ____ Alternate II (MAR 2000) of 252.247-7023.

(iv) ____ Alternate III (MAY 2002) of 252.247-7023.

(30) ____ 252.247-7024, Notification of Transportation of Supplies by Sea (MAR (2000) (10 U.S.C. 2631).

(31) X 252.247-7027, Riding Gang Member Requirements (OCT 2011) (Section 3504 of Pub. L. 110-417).

c) In addition to the clauses listed in paragraph (e) of the Contract Terms and Conditions Required to Implement Statutes or Executive Orders--Commercial Items clause of this contract (FAR 52.212-5), the Contractor shall include the terms of the following clauses, if applicable, in subcontracts for commercial items or commercial components, awarded at any tier under this contract:

(1) 252.225-7039, Contractors Performing Private Security Functions (JUN 2012) (Section 862 of Pub. L. 110-181, as amended by section 853 of Pub. L. 110-417 and sections 831 and 832 of Pub. L. 111-383).

2) 252.227-7013, Rights in Technical Data--Noncommercial Items (FEB 2012), if applicable (see 227.7103-6(a)).

(3) 252.227-7015, Technical Data--Commercial Items (DEC 2011), if applicable (see 227.7102-4(a)).

(4) 252.227-7037, Validation of Restrictive Markings on Technical Data (JUN 2012), if applicable (see 227.7102-4(c)).

(5) 252.237-7010, Prohibition on Interrogation of Detainees by Contractor Personnel (NOV 2010) (Section 1038 of Pub. L. 111-84).

(6) 252.237-7019, Training for Contractor Personnel Interacting with Detainees (SEP 2006) (Section 1092 of Pub. L. 108-375).

(7) 252.247-7003, Pass-Through of Motor Carrier Fuel Surcharge Adjustment to the Cost Bearer (SEP 2010) (Section 884 of Pub. L. 110-417).

(8) 252.247-7023, Transportation of Supplies by Sea (MAY 2002) (10 U.S.C. 2631).

(9) 252.247-7024, Notification of Transportation of Supplies by Sea (MAR 2000) (10 U.S.C. 2631).

(End of clause)

252.232-7006 WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (MAY 2013)

(a) Definitions. As used in this clause--

Department of Defense Activity Address Code (DoDAAC) is a six position code that uniquely identifies a unit, activity, or organization.

Document type means the type of payment request or receiving report available for creation in Wide Area WorkFlow (WAWF).

Local processing office (LPO) is the office responsible for payment certification when payment certification is done external to the entitlement system.

(b) Electronic invoicing. The WAWF system is the method to electronically process vendor payment requests and receiving reports, as authorized by DFARS 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports.

(c) WAWF access. To access WAWF, the Contractor shall--

(1) Have a designated electronic business point of contact in the System for Award Management at https://www.acquisition.gov; and

(2) Be registered to use WAWF at https://wawf.eb.mil/ following the step-by-step procedures for self-registration available at this Web site.

(d) WAWF training. The Contractor should follow the training instructions of the WAWF Web-Based Training Course and use the Practice Training Site before submitting payment requests through

WAWF. Both can be accessed by selecting the “Web Based Training” link on the WAWF home page at https://wawf.eb.mil/.

(e) WAWF methods of document submission. Document submissions may be via Web entry, Electronic Data Interchange, or File Transfer Protocol.

(f) WAWF payment instructions. The Contractor must use the following information when submitting payment requests and receiving reports in WAWF for this contract/order:

(1) Document type. The Contractor shall use the following document type(s).

(Contracting Officer: Insert applicable document type(s). Note: If a “Combo” document type is identified but not supportable by the Contractor's business systems, an “Invoice” (stand-alone) and

“Receiving Report” (stand-alone) document type may be used instead.)

(2) Inspection/acceptance location. The Contractor shall select the following inspection/acceptance location(s) in WAWF, as specified by the contracting officer.

(Contracting Officer: Insert inspection and acceptance locations or “Not applicable”.)

(3) Document routing. The Contractor shall use the information in the Routing Data Table below only to fill in applicable fields in WAWF when creating payment requests and receiving reports in the system.

Routing Data Table*

Field Name in WAWF

Data to be entered in WAWF

Pay Official DoDAAC

Issue By DoDAAC

Admin DoDAAC

Inspect By DoDAAC

Ship To Code

Ship From Code

Mark For Code

Service Approver (DoDAAC)

Service Acceptor (DoDAAC)

Accept at Other DoDAAC

LPO DoDAAC

DCAA Auditor DoDAAC

Other DoDAAC(s)

(*Contracting Officer: Insert applicable DoDAAC information or “See schedule” if multiple ship to/acceptance locations apply, or “Not applicable.”)

(4) Payment request and supporting documentation. The Contractor shall ensure a payment request includes appropriate contract line item and subline item descriptions of the work performed or supplies delivered, unit price/cost per unit, fee (if applicable), and all relevant back-up documentation, as defined in DFARS Appendix F, (e.g. timesheets) in support of each payment request.

(5) WAWF email notifications. The Contractor shall enter the email address identified below in the “Send Additional Email Notifications” field of WAWF once a document is submitted in the system.

(Contracting Officer: Insert applicable email addresses or “Not applicable.”)

(g) WAWF point of contact. (1) The Contractor may obtain clarification regarding invoicing in WAWF from the following contracting activity's WAWF point of contact.

(Contracting Officer: Insert applicable information or “Not applicable.”)

(2) For technical WAWF help, contact the WAWF helpdesk at 866-618-5988.

(End of clause)

5352.201-9101 OMBUDSMAN (AUG 2005) (AFFARS)

(a) An ombudsman has been appointed to hear and facilitate the resolution of concerns from offerors, potential offerors, and others for this acquisition. When requested, the ombudsman will maintain strict confidentiality as to the source of the concern. The existence of the ombudsman does not affect the authority of the program manager, contracting officer, or source selection official. Further, the ombudsman does not participate in the evaluation of proposals, the source selection process, or the adjudication of protests or formal contract disputes. The ombudsman may refer the party to another official who can resolve the concern.

(b) Before consulting with an ombudsman, interested parties must first address their concerns, issues, disagreements, and/or recommendations to the contracting officer for resolution. Consulting an ombudsman does not alter or postpone the timelines for any other processes (e.g., agency level bid protests, GAO bid protests, requests for debriefings, employee-employer actions, contests of OMB Circular A-76 competition performance decisions).

(c) If resolution cannot be made by the contracting officer, concerned parties may contact the Center/MAJCOM ombudsmen, Business & Mission Support Division Chief, Directorate of Contracting, OC-ALC/PKC, Tinker AFB OK 73145, Phone: 405-736-3273. Concerns, issues, disagreements, and recommendations that cannot be resolved at the MAJCOM/DRU level, may be brought by the concerned party for further consideration to the Air Force ombudsman, Associate Deputy Assistant Secretary (ADAS) (Contracting), SAF/AQC, 1060 Air Force Pentagon, Washington DC 20330-1060, phone number (703) 588-7004, facsimile number (703) 588-1067.

(d) The ombudsman has no authority to render a decision that binds the agency.

(e) Do not contact the ombudsman to request copies of the solicitation, verify offer due date, or clarify technical requirements. Such inquiries shall be directed to the Contracting Officer.

(End of clause)

TAFB 100-13. SHIPPING AND BILLING INFORMATION

IMPORTANT SHIPPING AND BILLING INFORMATION

SHIPPING/PACKAGING DOCUMENTATION:

The vendor shall identify and include on all packages and shipping documents pertaining to the order, in addition to other relevant information the following.

1) REQUISITION NUMBER – found in block # 1 of the purchase order (SF 1449)

NOTE: If the award has multiple line items, block # 1 will state “See Schedule”.

Refer to the individual line items for Purchase Request (Requisition) Number.

2) CONTRACT NUMBER – found in block # 2 of the purchase order (SF 1449)

INVOICES:

The vendor shall identify and include on their invoice, in addition to other relevant information the following.

1) REQUISITION NUMBER – found in block # 1 of the purchase order (SF 1449)

NOTE: If the award has multiple line items, block # 1 will state “See Schedule”.

Refer to the individual line items for Purchase Request (Requisition) Number.

2) CONTRACT NUMBER – found in block # 2 of the purchase order (SF 1449)

BE ADVISED THAT FAILURE TO PROVIDE THE ABOVE INFORMATION MAY RESULT IN A DELAY IN THE TIMELY PROCESSING OF YOUR INVOICE.

TAFB 100-17. “TRUCK ENTRY GATE” NOTICE

IMPORTANT DELIVERY INFORMATION

Tinker Air Force Base has constructed a “Truck Entry Gate” (Gate 33), which is located at the corner of 59th Street and Air Depot Blvd (southwest corner of the base). The gate will be opened beginning 15 September 2004.

Gate 33 shall be used for all deliveries by truck to this base.

(Trucks will not be allowed to gain access through any other gate.)

Since your firm’s delivery on this order is affected, please advise your delivery carrier to use the new gate. This should minimize the impact of your delivery.

DELIVERIES TO BUILDING 3001 (B / 3001)

Be advised that delivery vehicles destined for B / 3001 are prohibited from using “Staff Drive”.

Delivery vehicles may make deliveries only in designated unloading areas.

Since your firm’s delivery may be affected, ensure that your delivery carrier receives proper instructions on delivery / unloading requirements for B / 3001. Unloading in designated unloading areas will minimize any inconvenience, and, attendant ramifications, which may accrue, to your delivery / delivery carrier for failure to adhere to this requirement.