Attachment_1_-_SOW_(1_June_17).pdf

STATEMENT OF WORK

BASE CARPET AND FLOORING

Blanket Purchase Agreement

Mountain Home AFB, ID

1 June 2017

SECTION I

DESCRIPTION OF SERVICES

1. Scope: The contractor shall provide all personnel, equipment, tools, materials, supervision, administration, and services necessary to remove, dispose of, purchase, and install floor coverings and accessories as specified in each call. The work occurs in various facilities and commercial applications, on Mountain Home Air Force Base (MHAFB). All work to be performed will be in accordance with recommended manufacturer’s commercial specifications.

All references to specifications within this Statement of Work (SOW) require the use of the most current edition of the referenced material.

1.1. Coordination of Work: The contractor shall coordinate all removals and installations with the identified project manager (PM). Written work schedules detailing the performance and installation dates and estimated date of completion shall be submitted to the PM identified by the government prior to performance start. A copy of the building drawings depicting areas receiving services will be supplied to the contractor upon contractor acceptance of the call.

Contractor is responsible to field verify exact measurements and quantities of the area(s) to receive installation.

1.2. Removal of Floor Materials: The contractor shall remove all flooring materials to accommodate the installation of new materials. The contractor shall clean and prepare existing substrates to receive new materials in accordance with manufacturer’s published installation procedures.

1.3. Floor Preparation: Before any work begins, the contractor shall remove top layer of existing flooring and correct all defects such as rough or spalling concrete, low spots, high spots, and uneven surfaces to ensure a smooth, true, and level plane except where indicated as a sloped area. Concrete curing compounds, paint, varnish, oils, release agents, sealers, waxes, and adhesives shall be completely removed. Fill holes and cracks with a latex filler. Provide a latex under-layment to fill depressions and for smoothing, leveling, or to create a feathered edge.

Latex filler/under-layment shall have a minimum compressive strength of 2,500 Pounds per Square Inch. After cleaning and removal of loose particles, prime chalky or dusty surfaces with primer. If contractor determines that floating of floor is necessary, immediately contact the authorized callers prior to commencement of work. All adhesives under existing broadloom carpet shall be removed prior to new broadloom carpet or carpet tiles/squares installation. Floor preparation for carpet tiles/squares replacing existing carpet squares/tiles will be performed according to the manufacturer’s published installation procedures.

1.4. Floor Coverings: Floor covering are defined as carpet, tile, laminate or other items that cover the floor. Contractor shall attempt to match the color of the flooring material being removed.

1.5 Ordering Procedures:

1.5.1. IAW FAR 13.303-3(a)(2) All calls will be competed among Blanket Purchase Agreement (BPA) contractors at MHAFB. As the need exists for performance under the terms of the BPAs, the 366th Contracting Squadron (CONS) will notify the contractors of the new requirement and provide the contractors with a SOW for the project.

IAW FAR 13.303-3(a)(3) see 13.303-5(b) There will be a specified dollar limitation for each individual purchase under the BPA. The call limitation for each individual purchase is $25,000.00.

1.5.2. After receipt of this notification, a site visit with BPA contractors, Civil Engineering Squadron (CES) personnel, and CONS personnel will be held within three (3) business days.

The purpose of the site visit is scope validation, during which the following will be discussed:

Project number and title/work order Site investigation Methods and alternatives for accomplishing work Definition and refinement or requirements Scope of work Requirements for plans, sketches, shop drawings, etc.

Preliminary quantities

1.5.3. Upon completion of the site visit, the government will provide an updated project SOW as necessary to all BPA contractors, detailing any changes deemed necessary during the site visit.

The contractor shall then prepare a detailed quote in accordance with the project SOW for submission to CONS within three (3) business days of the site visit using the Contracting Officer (CO) approved price list.

1.5.4. Special Provisions for Measurements: The contractor’s unit-priced line items and their associated quantities shall be determined using the project SOW, measurements taken from the provided drawings and using field measurements taken at the site. In the absence of drawings, the contractor will be provided a detailed description of the proposed work and must perform measurements in the field during the site visit to verify the quantities of each unit priced item necessary to complete the work as described. Adequacy of quotes, to include quantities, will be determined by CES personnel during Technical Evaluations with the CO. Contractors will be asked to adjust quantities as necessary following Technical Evaluations. After the final quote is submitted, no changes to the agreed upon quantities will be made and no additional unit-priced line items will be added unless differing site conditions are encountered and the drawings and/or description of the work is modified by the CO with the concurrence of the contractor. The contractor is responsible for notifying the CO immediately upon encountering differing site conditions. No separate payment will be made for compliance with any provision of “Special Provisions for Measurement” as stated above. A 10% allowance for waste is authorized during measurement.

1.6. Blanket Purchase Agreement Calls:

1.6.1. Call Issuance: The government intends to issue a call, IAW FAR 13.303-3(a)(5), to the contractor that provides the lowest priced quote that is considered acceptable in accordance with the project SOW. Each call will designate the contract line items, quantities, extended amounts, period of performance, building number, and drawings. The contractor may be required to perform floor covering installation on multiple calls at one time.

1.6.2. Performance Time: Installation will commence within the agreed number of calendar days after contractor acceptance of the call. If floor covering material requires more delivery time from the manufacturer than the agreed performance period allows, the contractor shall provide a letter from the manufacturer stating the estimated date of shipment to contractor. The CO will coordinate a revised installation start date with contractor and PM. Upon agreement, written documentation of the change will be provided by the CO to the PM and contractor.

Installation shall normally be accomplished during normal duty hours of 7:30 A.M. to 4:30 P.M.

local time, Monday through Friday excluding federal holidays or when the Government facility is closed due to Base down days. Local or national emergencies may also affect access to base facilities. The contractor shall request, in writing, for performance periods outside the normal working hours. The contractor has 24 hours to respond regarding repair or replacement of damaged flooring materials caused by installation problems. A repair/replacement time will be coordinated with the CO and PM.

1.6.3. Pre-Installation Requirements: The contractor shall notify the PM immediately of any condition(s) that will prevent the suitable completion of the delivery order, such as sub-floor conditions preventing a proper installation, etc.

1.6.4. Post-Installation Requirements: The contractor shall notify the PM immediately after each call is complete and quality control has been performed to schedule an acceptance inspection.

1.6.5. Invoicing Instructions: IAW FAR 13.303-3(a)(6) A summary invoice shall be submitted at least monthly or upon expiration of this BPA, whichever occurs first, for all deliveries made during a billing period, identifying the delivery tickets covered therein, stating their total dollar value, and supported by receipt copies of the delivery tickets.

1.7. Flooring Materials:

1.7.1. Non-Reimbursable Materials: The contractor shall furnish adhesives, seam sealer, seam tape, tack strips, seam sticks, welding rods etc. for installation of floor covering materials at no additional cost to the government. Cost for these items shall be included in the price for the appropriate line item. Ancillary products used during installation must be in accordance with the manufacturer’s published installation instructions for the primary product.

1.7.2. Color and Material Selections:

1.7.2.1. The contractor shall submit, for government selection, the manufacturer's full range of applicable colors, patterns, and textures for the various materials that are required by the agreement and within the guidelines stated in this SOW. The government will require product samples or swatches and the manufacturer’s published installation instructions.

1.7.2.2. No color selections and no material selections will be made by the government until the contractor submits all samples of all materials requiring color selections to the government. In addition, prior to the government selecting colors, the contractor shall certify in writing that all colors and samples submitted are current.

1.7.2.3. In the event that discontinued, non-current, or non-applicable colors, textures, or samples are submitted by the contractor to the government and their selection is made by the government, the contractor shall bear all labor and material correction costs for fabrication, shipping, restocking, removal, repair of damaged materials, and installing of all materials required by the government to correct the project.

1.7.2.4. The contractor shall provide initially, and maintain current in the office of CES and CONS samples reflecting the full range of materials offered under this SOW.

1.7.2.5. Carpet Pad: Carpet padding shall meet moderate to extra heavy commercial standards, minimum 1/4” thickness, 25 pound, anti-microbial density. Carpet padding for commercial applications shall be installed using the double glue or double stick down method and the standard for commercial carpet CRI – 104. Recycled padding shall be used to the greatest extent possible.

1.7.2.6. Commercial Carpet and Carpet Tile: Carpet/Carpet Tile for commercial applications shall be installed using the standard for commercial carpet CRI – 104.

1.7.2.7. Ceramic, Quarry Pavers, and Accessories: All flooring shall be Class IV-Heavy Traffic or Class IV Plus-Extra Heavy Traffic as rated by the manufacturer when tested in accordance with American Society for Testing Materials (ASTM) C 1027 and ASTM C 1028.

1.7.2.8. Vinyl Composition Tile: Vinyl composition tile shall be asbestos free and conform to ASTM F 1066. Materials shall be from the same lot and have the same shade and pattern. Solid vinyl tiles shall be asbestos free and conform to ASTM F 1700. Stair treads/nosings shall be one piece.

1.7.2.9. Vinyl/Rubber Base Cove: Surfaces on which new base cove is to be applied shall be patched and be free of all foreign materials. Rubber tile and products shall conform to ASTM F 1344. Base cove material shall be manufacturer’s standard 120’ coils. Color shall be identified in the project SOW for each call. Manufacturer’s preformed inside and outside corners shall match the straight length of base cove. The contractor shall not use straight lengths of base cove that are bent, folded, tucked or creased around corners.

1.7.2.10. Wood Products/Accessories: Commercial grade products shall be provided, and installed in accordance with manufacturer’s printed instructions. Finishes will be applied to match existing construction.

1.8. Other Floor Cover Services: Contractor shall provide labor, modify/cut wood doors, seal grout and burnish vinyl composition tile (VCT) as necessary.

1.9. Furniture Moving:

1.9.1. Furniture Moving: The contractor will be responsible for the removal and reinstallation of the following furniture type items: desks, bookcases, cabinets, credenzas, tables, boxes, chairs, trash cans, and dormitory furnishings. Contractor will not be responsible for the moving of computer equipment, telephones, vending machines, personal items, safes, pool tables, or wall hangings. Furniture moved by the contractor shall be returned to its original location.

1.9.2. System and Modular Furniture: Defined as furniture set in square/cubicle patterns with desks/tables/cabinets built integrally into or hung onto the wall system. The contractor shall only lift and reset system and modular furniture to the extent necessary for tucking carpet tile under walls/legs. Units may be inter-connected. Contractor will not disassemble/reassemble modular/system furniture.

1.10. Government Surveillance: Government will perform inspections during and at the completion of each project. Work performance will be measured against the standards in this SOW and the project SOW.

1.11. Cleanup and Disposal: Vacuum newly installed carpet using a machine with a face-beater bar element. Remove spots or stains and replace flooring materials where spots cannot be removed. Clean base cove of all foreign materials. Clean all other flooring materials according to the manufacturer recommendations and specifications. The contractor is responsible for removing all waste materials and debris from the installation site and discarding at a state permitted disposal site. Clean completed tile surfaces in accordance with manufacturer’s approved cleaning instructions.

1.12. Warranty: Warranties under this agreement will include standard warranties offered by the manufacturers to the general public. The contractor is responsible for replacing items within an appropriate period of such warranty for all floor covering products covered in this SOW. In addition to the manufacturer’s warranties, the contractor shall provide an initial warranty of 1 year on all materials and installations.

SECTION II

GOVERNMENT FURNISHED PROPERTY AND SERVICES

2. Government-Furnished Property and Services: Electricity, sewage, and water will be made available where existing. The contractor shall ensure all employees practice utilities conservation. All alterations or temporary connections to government utilities shall be the responsibility of the contractor; and shall be restored to the original condition upon completion of each call. No temporary connections will be allowed until the contractor has submitted a detailed plan for the connection and has received approval from the government for the connection as planned. The plan shall include a detailed description on how the connection will be restored to its original condition or better.

SECTION III

GENERAL INFORMATION

3.1. Personnel: The contractor shall provide a contract manager who shall be responsible for the performance of the work. The name of this person and alternate(s) who shall act for the contractor when the manager is absent shall be designated in writing to the CO prior to performance.

3.1.1. The contract manager or alternate shall be available during BPA call performance within 2 hours to meet on the installation with government personnel to discuss work requirements or problem areas.

3.1.2. The contract manager and alternate must be able to converse in English, both orally and in writing.

3.1.3. Employees are expected to comply with reasonable dress and grooming standards based on comfort, productivity, health, and types of positions occupied. Attire shall be in good repair and shall not be considered offensive, disruptive, or unsafe. Contractor personnel shall be easily recognizable while on the installation in conjunction with this contract. This shall be accomplished through the wear of distinctive clothing, overcoats, or hats bearing the company name or logo. The coloring or design of the items selected should be such that the item identifies personnel easily and quickly for reasons of safety and personal protection. The Government is authorized to restrict base access to any contractor employee or prospective contractor employee who is identified as a potential threat to the health, safety, security, general wellbeing, or operational mission of the installation and its population. In addition, at any time a contractor employee maybe asked to provide proof of a government-issued badge and must accommodate such request. In the case of a contractor employee only working on the base on a temporary base they will have to show their temporary pass showing they are on base legally.

3.1.4. Contractor shall provide a foreman who is currently certified by the International Certified Floor Covering Installers Association, (ICFCIA) Commercial II or higher. All workers shall maintain certification by the IFCIA or manufacturer for the product being installed. The foreman shall be on Mountain Home AFB at all times while work is being performed. Contractor shall provide copies of certification to the CO within 90 days of BPA issuance.

3.2. Contractor Vehicles

3.2.1. Vehicles: The contractor shall provide and maintain vehicles for transportation to meet the requirements of this contract. All vehicles used in the performance of this contract shall have the company name prominently displayed on both sides of the vehicle and be maintained to present a clean, neat, and professional appearance at all times.

3.3. General

3.3.1. The contractor shall comply with security regulations imposed by the Installation Commander and the agency occupying the space where work is to be performed, including any necessary security clearances.

3.3.2. The contractor shall be responsible for safeguarding all government property provided. At the close of each work period, facilities, equipment and materials shall be secured.

3.4. Performance of Services during Crisis: Floor covering services at MHAFB are not considered mission essential and only limited service will continue in the event of crisis, whether declared by the National Command Authority under provisions of DoDI 3020.37, or otherwise.

Contractor employees, with approved background checks, will be allowed unescorted access to the base for performance of work in all Force Protection Conditions except “Delta”. The CO will notify the contractor of a “Delta” condition as soon as possible after security procedures have been implemented.

3.5. Holidays: The contractor is not required to provide services on the following holidays:

New Year’s Day, Martin Luther King’s Birthday, President’s Day, Memorial Day, Independence Day, Labor Day, Columbus Day, Veterans Day, Thanksgiving Day, and Christmas Day.

APPENDIX 1: GENERAL SECURITY REQUIREMENTS FOR UNCLASSIFIED

CONTRACTS

A1. GENERAL:

A1.1. SCOPE: These standards apply to all new construction, demolition, rehabilitation, alteration, modification, repair, and maintenance contracts for existing facilities.

A1.2. GENERAL REQUIREMENTS: Compliance with Laws: The contractor shall comply, and ensure that all subcontractor(s) comply with all applicable Federal, State, and Local laws, regulations, ordinances and standards related to safety and security matters at Mountain Home Air Force Base.

A1.3. PASS AND IDENTIFICATION REQUIREMENTS:

A1.3.1. All contractors who work on base must submit an SFS Form 30 to request base access.

An AF Form 75 will be issued for periods of up to 30 days, and a contractor pass will be issued when access is required in excess of 30 days. A complete background check will be conducted on all employees. Contractor passes will not exceed a period of 1 year.

A1.3.2. Delivery vehicles will be granted access to the base upon presentation of a valid bill of lading and/or delivery slip indicating delivery destination and point of contact. Work orders are not acceptable for access.

A1.3.3. Refusal to provide personal information on the SFS Form 30 will result in denial of access.

A1.3.4. Current driver’s license, vehicle registration, and insurance documents must be maintained in vehicles and presented upon request.

A1.3.5. Base access will be contingent upon the receipt of a favorable background check, conducted by Security Forces. Access may be denied based upon the results of the background check. Unfavorable access decisions may be appealed to the 366 MSG/CC. "Favorable" background checks will not contain any of the following negative screening criteria (i.e., "disqualifying factors"):

- U.S. citizenship, immigration status, or Social Security Number cannot be verified

- Barred from entry/access to any military installation or facility

- Wanted by federal or civil law enforcement authorities, regardless of offense/violation

(i.e., an "order to arrest" has been issued by a judge)

- Conviction of a firearms or explosives violation within the past 3 years

- Incarceration for 12 months or longer within the past 3 years, regardless of offense/violation

- Conviction for espionage, sabotage, treason, terrorism, murder, sexual assault, armed assault/robbery, rape, or child molestation

- Name appears on any federal agency's "watch list" or "hit list" for criminal behavior or terrorist activity

A1.3.6. Retrieving Identification Media: The contractor shall retrieve all identification media, from employees who depart for any reason before the contract expires, e.g., terminated for cause, retirement, etc., and return badges/media to the CO. Report lost passes and identification badges immediately to Security Forces and the CO.

A1.4. LISTING OF EMPLOYEES: The contractor shall maintain a current listing of employees. The list shall include employee's name, social security number, and date of investigation if contract work involves unescorted entry to Air Force restricted or other sensitive areas designated by the Installation Commander. The list shall be validated and signed by the contractor representative with the authority to bind the contractor, and provided to the CO prior to the contract start date. Updated listings shall be provided when an employee's status or information changes.

A1.5. REPORTING REQUIREMENTS: The contractor shall comply with Air Force Instruction (AFI) 71-101, Volume-1, Criminal Investigations, and Volume-2, Protective Service Matters, requirements. Contractor personnel shall report to the CO any information or circumstances of which they are aware that may pose a threat to the security of DOD personnel, contractor personnel, resources, and classified or unclassified defense information. Contractor employees shall be briefed by their immediate supervisor upon initial on-base assignment and as required thereafter.

A1.6. TRAFFIC LAWS: The contractor and employees shall comply with base traffic regulations in accordance to the provisions of AFI 31-204.

A1.7. BASE EXERCISES: Upon implementation of a base exercise, the contractor will be required to present a MHAFB contractors badge indicating they are exempt. When determined to be in the best interest of the government, the 366 SFS will release the contractor to continue their work.

APPENDIX 2: SPECIFICATIONS

CLIN Description 0001AA Remove Carpet Glue Down

Remove existing product and prepare surface for application of new product in accordance with manufacturer’s specifications. Dispose materials off-base.

0001AB Remove Rubber Cove Base Remove existing product and prepare surface for application of new product in accordance with manufacturer’s specifications. Dispose materials off-base.

0001AC Remove Carpet Cove Base Remove existing product and prepare surface for application of new product in accordance with manufacturer’s specifications. Dispose materials off-base.

0001AD Remove Vinyl Tile Remove existing product and prepare surface for application of new product in accordance with manufacturer’s specifications. Dispose materials off-base.

0001AE Remove Sheet Vinyl Remove existing product and prepare surface for application of new product in accordance with manufacturer’s specifications. Dispose materials off-base.

0001AF Remove Double Stick Pad Remove existing product and prepare surface for application of new product in accordance with manufacturer’s specifications. Dispose materials off-base.

0001AG Remove Wood Base Board Remove existing product and prepare surface for application of new product in accordance with manufacturer’s specifications. Dispose materials off-base.

0001AH Remove Laminate Floor Remove existing product and prepare surface for application of new product in accordance with manufacturer’s specifications. Dispose materials off-base.

0001AJ Remove Ceramic Floor Tile Remove existing product and prepare surface for application of new product in accordance with manufacturer’s specifications. Dispose materials off-base.

0001AK Remove Ceramic Cove Base Remove existing product and prepare surface for application of new product in accordance with manufacturer’s specifications. Dispose materials off-base.

0001AL Remove Carpet Squares Remove existing product and prepare surface for application of new product in accordance with manufacturer’s specifications. Dispose materials off-base.

0001AM Remove Commercial Stair Tread Remove existing product and prepare surface for application of new product in accordance with manufacturer’s specifications. Dispose materials off-base.

0001AN Remove Commercial Stair Riser Remove existing product and prepare surface for application of new product in accordance with manufacturer’s specifications. Dispose materials off-base.

0001AP Remove Commercial Stair Stringers Remove existing product and prepare surface for application of new product in accordance with manufacturer’s specifications. Dispose materials off-base.

0001AQ

Broadloom Carpet Installed Shaw Constellation or Equal Construction Type Pattern Loop Face Fiber EcoSolution Q Nylon Gauge 1/10 Stitches 10 Density 7,800 Yarn Weight 26 oz.

Pile Thickness (ASTM D-418) .120 inches Backing Structure TekLok Recycled Content 10.3% pre-consumer Cradle to Cradle Certified Fiber must be MBDC Cradle to Cradle Certified Width 12' Base Color Method 70% solution dyed/30% yarn dyed

0001AR

Carpet-Broadloom Self Padded Installed Shaw Scepter II or equal Fiber Content: 100% Piece Dyed Fiber Type: Nylon Face Construction: Solid Cut Pile Gauge: 1/10 Stitches: 12.0 Pile Thickness: .243 inch Surface Pile Weight: 42.0 oz/sq. yd.

Density: 6,222 Primary Backing: Synthetic Secondary Backing: ClassicBac Width: 12 ft. Broadloom Critical Radiant Flux Classification: Class 1 Carpet must be CRI Green Label Certified

0001AS

Carpet Squares Installed Shaw Constellation EW24 or equal Construction Type Graphic Loop Face Fiber 100% EcoSolution Q BCF SD nylon 6 Yarn Treatment Shaw Soil Protection Gauge 1/10 Stitches 10.0

Pile Density (UM 44D) 8,727 oz/yd³ Weight Density 209,448 Yarn Weight 24 oz/yd² Pile Thickness (ASTM D-418) .099 in.

Backing Structure 67.9 oz/yd² EcoWorx polyolefin recyclable composite.

Total Weight 102.3 oz/yd² Total Thickness .273 in.

Size 24 in. x 24 in.

Base Color Method 55% solution dyed; 45% yarn dyed Antimicrobial Florsept Antimicrobial

0001AT Carpet Indoor/Outdoor Installed Coronet, Harmony or equal.

Construction: Heavy Hobnail Fiber: 100% UV Olefin Dye Method: Solution Oz. Per Square Yard: 24 OZ.

Average Pile Height: 5 MM Density: N/A Secondary Backing: Unitary Latex Pattern Repeat: N/A Flammability: Class II Fade Warranty, Indoor: 3 Year Fade Warranty, Outdoor: 2 Year Wear Warranty, Indoor: 3 Year Wear Warranty, Outdoor: 2 Year

0001AU Vinyl Composite Tile 12" X 12" Installed Armstrong Imperial Texture Standard Excelon or equal.

12 in Wide x 12 in Length Gauge: 1/8” ASTM F 1066 Class 2 - through-pattern ASTM E 648 Critical Radiant Flux Class I - 0.45 or more watts/cm2 ASTM E 662 Smoke Developed 450 or less Static Load Limit: ASTM F 970 125 psi

001AV Tile Grout Sealer Applied Apply DuPont™ StoneTech® Professional Grout Sealer or equal to grout joints in floor tile, taking care to protect baseboards and other adjacent surfaces. Clean excess sealer from tile surfaces.

0001AW Ceramic Floor Tile Installed American Olean Tile Co Series: Amiata or equal.

5/16 inch thick, grout width 1/4 inch.

Specification: ANSI A137.1 - Specifications for Ceramic Tile Static Coefficient of Friction: Tile on walkway surfaces will meet or exceed the following values as determined by testing in conformance with ASTM C 1028.

0001AX Quarry Tile Installed Quarry tile for floor and base will be domestic, standard grade, slip resistant by American Olean, Dal-Tile, Crossville, or Summitville Specification: ANSI A137.1.

ADAAG slip resistance coefficient of 0.6 on static surfaces and 0.8 on ramps, Thickness: ½” thickness Base will be cove, bull nose top 6" x 5" x ½" to match floor.

0001AY Laminate Floor Installed Pergo Commercial Grade “Select” or equal Wear Resistant Rating: AC5 Resistance to Staining: Class 5 Laminate Thickness: 0.7 mm.

Total Plank Thickness: 10mm.

Warranty: Limited 10 year Commercial

0001AZ Laminate Trim Finish Sticks 8' Installed Install transitions, reducers, and other accessories needed to complete installation of laminate floor using products from the same manufacturer as the floor surface.

0001BA Sheet Vinyl Installed Mannington CustomSpec II or equal Gauge: Overall Nominal Thickness -- .085" Wearlayer Thickness: .020" Average Weight: 3.8 lbs/s.y.

Width: 12' Recommended Load Limit: Static Load Limit -- 100 p.s.i.

Reference Specifications: ASTM F-1303-97 - Type I, Grade 1, Class A Traffic: Moderate Warranty: CustomSpec II Limited 5-Year Commercial Warranty. Limited 5-Year AquaLoc® Moisture Protection Warranty against Discoloration Caused by Alkali and Mildew.

0001BB Cove Base Rubber 4" Installed Installation of rubber cove base on vertical surfaces, measured in linear feet. Unit price includes accessories items for inside and outside corners from same manufacturer.

Roppe 700 Series Rubber Wall Base or equal Type: TP Thermoplastic Rubber TPR 700 Series Base ASTM Specification: F-1861 Height: 4” Thickness: 1/8”

0001BC Binding Carpet Cove Base, 4" Installed Labor and materials to cut, seam, bind, and install carpet vertically around perimeter of rooms.

Carpet yardage measured and provided in other CLINs. Unit price includes seaming of one joint and binding of one side, measured in linear feet

0001BD Ceramic Wall base Bullnose Installed 6" x 5" X 1/2" Install Wall base matching product used for floor area, with appropriate accessories at inside and outside corners.

0001BE Stair Nosing Metal/Rubber Installed Roppe #204/206 or Equal Undercut/Double undercut stair nose Description: Heavy-duty for 1/4" and 5/16" carpet Type: TP Thermoplastic Rubber

0001BF Wood Base Board 3"1/4 Installed Install Trimco Millwork Oak TM444 or equal on walls after installation of floor covering. Paint or stain to match

0001BG Wood 1/4 Round Installed Install Trimco Millwork Oak 3/4”x3/4” quarter round on walls, cabinets after installation of floor covering. Paint or stain to match

0001BH Carpet Plush, Installed Shaw Terra UMPC or Equal Primary Backing: Synthetic Secondary Backing: Ultraloc MPC Width: 12’

Carpet must be CRI Green Label Certified Critical Radiant Flux Classification: Class 1 Optical Density of Smoke(flaming) not more than 450 per ASTM E662-97 Electrostatic Propensity no greater than 3.0 as per AATCC 134-1991 Colorfastness to Crocking: Not less than 4, wet and dry, per AATCC-165.

Colorfastness to Light: Not less than 4 after 40 AFU (AATCC fading units) per AATCC-16.

Antimicrobial Activity: Not less than 2-mm halo of inhibition for gram-positive bacteria; not less than 1-mm halo of inhibition for gram-negative bacteria; no fungal growth; per AATCC- 174.

0001BJ Reducer/ Metal or Rubber Installed Install Armstrong Commercial Floor products VT0 1/4" Carpet to 1/8" Tile Reducer or equal to provide a smooth transition between different height floor finishes.

0001BK Thresholds Metal Installed 0001BL Knapp Lock Metal Installed

Install M-d Products 1-3/8" Aluminum Floor & Carpet Gripper With Teeth, Model #: 43886 or equal to provide a finished transition between carpet and other floor surfaces

0001BM Commercial Stair Tread Installed Install Armstrong Floor Products STAIR TREAD, or equal, ASTM F 2169

Type TS, Class 2

(Supercedes FS RR-T-650 Composition A, Type 2)

Low profile raised elements that have chamfered shoulders with sharply defined edges at the top. The solid color is uniform throughout the entire thickness of the tread, risers and tile. Color pigments are insoluble in water and resistant to cleaning agents and light.

0001BN Commercial Stair Riser per Installed Install Armstrong Floor Products STAIR RISER, or equal, ASTM F 2169

Type TS, Class 2 (Supercedes FS RR-T-650 Composition A, Type 2) Low profile raised elements that have chamfered shoulders with sharply defined edges at the top. The solid color is uniform throughout the entire thickness of the tread, risers and tile. Color pigments are insoluble in water and resistant to cleaning agents and light.

0001BP Commercial Stair Stringers Installed Install Roppe commercial grade stair stringer material of same thickness as risers, height and length after cutting to fit risers and treads and to cover stair stringers; produced by same manufacturer as treads and recommended by manufacturer for installation with treads.

0001BQ Carpet Border Installed Labor and materials to cut, seam, and install carpet around perimeter of rooms, as an accent stripe, or to highlight an area. Carpet yardage measured and provided in other CLINs. Unit price includes seaming of one joint measured in linear feet

0001BR Carpet Steps Labor and materials to fit and install carpet, also known as upholstering, on stairways. Unit price includes one tread and one riser. Carpet yardage measured and provided in other CLINs.

0001BS Trim Doors

Trim bottom of wood/metal door, taking care to protect finish, to allow for thickness of new floor covering

0001BT General Labor/ Floor Prep etc.

Provide labor proficient in the required tasks to perform tasks necessary to facilitate installation of new floor coverings.

0001BU Burnish/Polish New VCT Prepare tile surface, apply manufacturer’s recommended commercial grade polish, and mechanically buff to a high gloss finish

0001BV Moving light Furniture Move and replace items such as lamps, trash cans, chairs, etc. under 75 lbs.

0001BW Moving Heavy Furniture Move and replace items such as desks, bookcases, credenzas, etc. over 75 lbs.

0001BX Moving Systems Furniture Lift and replace one cubicle/workspace of systems furniture

0001BY Cove Base Rubber 6” Installed Installation of rubber cove base on vertical surfaces, measured in linear Feet. Unit price includes accessories items for inside and outside corners from same manufacturer.

Roppe 700 Series Rubber Wall Base or equal Type: TP Thermoplastic Rubber TPR 700 Series Base ASTM Specification: F-1861 Height: 6” Thickness: 1/8”