Attachment 1 Salient Characteristics (Rev.1) 20 May 2024.pdf

SALIENT CHARACTERISTICS

FOR

Weapon Storage Racks

May 2024

FA462024QA310

Attachment 1 Salient Characteristics (Rev. 1) 20 May 24

Salient Characteristics For

Weapon Storage Racks

Fairchild AFB, WA

1. BACKGROUND: The 92d Security Forces Squadron (SFS) has a requirement for a weapon storage rack upgrade storage capabilities for additional weapons. The weapon rack room area is 18 ft x 36 ft. All government provided dimensions are estimated. It is the responsible of the contractor to verify all dimensions provided before install.

2. OBJECTIVES: Obtain storage racks and panels that will be used to store weapons and equipment as outlined in the Requirements section, as well as the removal of existing SpaceSaver mobile storage racks, static rifle racks, and repair of structure floor where existing mobile rack system is established.

3. REQUIREMENTS: The contractor shall deliver and install storage racks, storage panels, and 150 plastic bins IAW the characteristics provided below:

ITEM 1: Storage Racks

• Dimensions shall be at or within 85x36x15 to 85x42x15

• One set of doors per rack

• Doors perforated to enable visual weapon inventory while secured

• Full piano hinge

• Reverse bi-folding security door

• 9 Point locking system

• 8 internal lock rods

• Hinged lock bar for use with padlock

• Recessed Handles (Twisting or Turning Handles Not Acceptable)

• Non-marring weapon bases for all identified weapon types and quantities

• Rack Base must be slotted with 23 groves for multi-position base inserts

• Weapons must be able to be stored vertically and laterally within the rack

• Saddles and Bungee retainers for all identified weapon types and quantities to ensure weapons cannot fall out of rack (to ensure Armorer safety and mitigate risk of damage to optics)

• Racks shall be configured to store weapons and equipment in the following quantities: *Note:

individual rack configuration is at the Vendor’s discrepancy unless specified by User.

- 250 - M4A1 Carbine and M18 Pistol as a set, with associated ammunition (4 rifle magazines and 2 pistol magazines) stored on shelving that divides the upper and lower tiers of weapons within the rack structure. *Note: Rifles require 5” in width due to optics/accessories

- 60 – M4 Carbine with associated ammunition (4 rifle magazines) stored on shelving that divides the upper and lower tiers of weapons within the rack structure. *Note: No increased width due to accessories

- 60 – Pistols, Various (Sig/Beretta/Glock) with associated ammunition (2 magazines each) *Note: may be stored on pegs that fit the ID of the barrel but must not mar the barrel

- 5 – M110A1 Rifle with associated suppressors

- 16 – M240B Machine Guns with spare barrels which must remain with host weapon

- 26 – M249 Automatic Rifles with spare barrels which must remain with host weapon

- 40 – M320 Grenade Launchers, detached

- 10 – M870 Shotguns

- 42 – X26 Tasers with two cartridges each

FA462024QA310

- 88 – AN/PVS-31 NVG’s

- 40 – Binoculars (various)

- 10 – Thermal Monoculars

- 6 – Thermal Sights in cases

- Misc. Storage, rack must contain adjustable shelving to accommodate various equipment

- Do Not Arm Rack: Single rack must be capable of storing up to 14 M4A1 Rifles (5” width) and Pistol Sets, not including ammunition

• Racks shall be bolted and welded to structure floor

*The specific number of panels and their specific configuration is to be determined by the contractor based on the space available within the facility and the ability to store the equipment listed above.

ITEM 2: Panel

• Dimensions shall be any of the sized: 48” x 36”, 48” x 30”, 36” x 36”, or 36” x 30

• The back panel must be fully slotted on 1” vertical increments to enable adjustability of components within the rack

• Panels shall be mounted with hardware suitable for use in cinder block walls

• Shall be able to support a weight of at least 300 lbs

*The specific number of panels and their specific configuration is to be determined by the contractor based on the space available within the facility and the ability to store plastic bins being provide under item 3.

ITEM 3: Plastic Bin (150 EA)

• 150 Bins shall be approximately 6 in. W x 7 in. L to accommodate radio and baton storage and be mountable to ITEM 2: Panel.

4. APPENDICES:

Appendix A: Old Weapons Rack Removal Appendix B: Floor Plan of Facility

FA462024QA310

The contractor shall remove and dispose of the old weapon rack equipment which includes:

Spacesaver System: 5 Mobile Racks, 1 Static Rack, (Racks are approximately 11 ft W x 7 ft T 6 Static Military Racks for M16/M4 Underground Motor that moves racks The contractor is responsible for repair of any floor damage that occurs as a result of the removal of the old weapon rack system.

FA462024QA310

-./01 2345�67�

89�

:;<=>?@ABCDE F

GHIJ� K�L� M5N�7� OP�Q�R� S�TUVW� X�Y�

Z�����[�Z����\[� ]������ _̂̀�� �aa b�b

K� c� d�FA462024QA310