20261015 - Environmental Special Conditions - Division 1-01 57-1C_3 Rev 0.pdf

PDF 774 KB Posted

Attached to
Gas Line Repair
Solicitation number
FA460027Q0011
Issued by

About this file

This document is Section 01 57 19, Environmental Special Conditions for the Offutt Air Force Base, Revision 15, October 2026. It establishes comprehensive environmental compliance requirements that contractors must follow when conducting work on Offutt AFB property.

The specification mandates contractor compliance with all current Air Force, Department of Defense, Federal, State, and local environmental laws, regulations, and permits. Key requirements include submitting Safety Data Sheets for all hazardous materials fifteen working days prior to bringing materials onto the base; obtaining government authorization through the Environmental Element (55 CES/CEIE) for all hazardous materials via the EESOH-MIS database; and implementing Hazardous Material Storage Plans with secondary containment holding at least 110% of the largest container volume. For regulated wastes, contractors must operate Satellite Accumulation Points approved by the government, maintain hazardous waste training documentation, and dispose of all waste through authorized methods, with no waste permitted to remain on base after project completion. Spill reporting must occur immediately via 911, followed by written reports to 55 CES/CEIE, with contractors bearing all cleanup and remediation costs.

Additional environmental obligations include Storm Water Pollution Prevention Plans (SWPPP) for projects disturbing one acre or more, requiring NPDES permits from the Nebraska Department of Water, Environmental, and Energy (NDWEE); dewatering operation permits from NDWEE; Spill Prevention Control and Countermeasure (SPCC) Plans for petroleum storage; and dust control measures. Contractors must divert at least fifty percent of construction and demolition debris from landfills and submit quarterly waste diversion reports. Special procedures apply to excavation activities where contractors must immediately cease work and report findings of unusual materials (contaminated soils, spills, containers, debris) to the Contracting Officer Representative or call 911. The specification includes requirements for EPA stormwater training certification, archaeological discovery protocols, testing using standardized EPA methods, environmental training via the TEACH platform, jurisdictional wetland permits from the U.S. Army Corps of Engineers, and radioactive source authorization from the Radiation Safety Officer. The 55 CES/CEIE Environmental Compliance office serves as the primary point of contact at 402-294-4087 during duty hours or 402-650-5685 for emergencies.

View the file

Other files

File Type Posted
Wage Determination - Heavy - NE20260051.pdf PDF
PWS Gas Line Repairs rev3.pdf PDF
Solicitation - FA460027Q0011.pdf PDF
Site Conditions.pdf PDF

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

Offutt Air Force Base Rev 15 Oct 2026-0

01 57 19-1

DoD Unified Specs: https://www.wbdg.org/ffc/dod/unified-facilities-guide-specifications-ufgs

Note 1. 55 CES/CEIE Environmental Special Condition specs utilize the above weblink or DoD unified specs as a boiler plate and then incorporates regulatory requirements for local/state/federal that are unique to Offutt

AFB.

Note 2. All permits and regulatory driven documentation must first be coordinated with 55 CES/CEIE – Environmental Compliance, 402-294-4087.

Note 3. Radioactive source authorization, reference Section 1.18 must be coordinated through 55 OMRS/SGXB - Bioenvironmental Engineering Flight, 402-294-6319.

SECTION 01 57 19

ENVIRONMENTAL SPECIAL CONDITIONS

PART 1 – GENERAL

1.1 ENVIRONMENTAL COMPLIANCE

1.1.1 The Contractor shall comply with all current Air Force, Department of Defense, Federal, State and local laws, regulations, instructions, policies and permits relating to environmental compliance. DAFMAN32-7002:

4.2.4. AF organizations that oversee government-owned, contractor-operated (GOCO) facilities shall ensure that the contracts include provisions that obligate the contractor to: all applicable federal, state, and local requirements (including permits). afman32-7002.pdf

1.1.2 Unfamiliarity or disregard by the Contractor of such laws, regulations, instructions, policies and permits shall not constitute a defense for violations issued by Federal, State or local compliance authorities. The cost of any fine, penalty or remediation for violations shall be borne fully by the Contractor communicated through/to the Contract Officer Representative (COR).

1.1.3 The 55th Civil Engineer Squadron’s (55 CES) Environmental Element (CEIE) is the subject matter POC for environmental compliance on Offutt Air Force Base and its associated properties. CEIE can be accessed by the 55th Contracting Squadron (55 CONS) or the Air Force Contracting Officer’s Representative (COR) in reference to contracting activities/questions at 402-294-4087 during duty hours or 402-650-5685 after duty hours for emergent issues (AF CORs should relay any USACE activities/questions per AFCEC/CFDO).

1.1.4. Federal Acquisition Regulation (FAR) Clauses to Consider in all contracts:

• FAR Clause 52.223-3, Hazardous Material Identification and Material Safety Data

• FAR Clause 52.223-5, Pollution Prevention and Right-to-Know Information

• FAR Clause 52.223-7, Notice of Radioactive Materials

• FAR Clause 52.223-19, Compliance with Environmental Management Systems

• AF FAR Supplement Clause 5352.223-9001, Health and Safety on Government Installations

1.2 SAFETY DATA SHEETS (formerly called: MATERIAL SAFETY DATA SHEETS)

1.2.1 Definitions

‘Enterprise Environmental, Safety and Occupational Health – Management Information System’ (EESOH-MIS) is a single point validated entry, which provides a secure, scalable development environment based on Oracle 9l, that is platform independent. Database allows ESOH to effectively manage multiple years of information and enables users to retrieve historical information regarding hazmat usage and environmental reporting.

https://www.wbdg.org/ffc/dod/unified-facilities-guide-specifications-ufgs https://static.e-publishing.af.mil/production/1/af_a4/publication/afman32-7002/afman32-7002.pdf

01 57 19-2

‘Priority chemical’ means a chemical identified by the interagency Environmental Leadership as such.

‘Toxic chemical’ means a chemical or chemical category listed in 40 CFR Chapter 1, Subpart D, § 372.65.

‘Hazardous material’ includes the following:

• Hazardous materials as defined by The Department of Transportation in 49 CFR 172

• Hazardous substances, extremely hazardous substances, toxic chemicals and hazardous waste as defined by EPA in Title III of the Superfund Amendments and Reauthorization Act and the Resource Conservation and Recovery Act, in 40 CFR

• Hazardous Chemicals and Hazardous Substances as defined by the Occupational Safety and Health Administration (OSHA) in 29 CFR 1910, Subpart H – “Hazardous Materials”

1.2.2 Federal facilities must comply with the provisions of the Emergency Planning and Community Right-to- Know Act of 1986 (EPCRA) (42 U.S.C. 11001-11023) and elements of the Pollution Prevention Act of 1990 (PPA) section 6607 (42 U.S.C. 13106).

The Contractor Reporting sections of Federal Acquisition Regulation (FAR) 52.223-5 (Pollution Prevention and Right-to-Know Information), require Contractors to provide all information needed by the Federal facility to comply with the following:

(1) The emergency planning reporting requirements of Section 370 of EPCRA;

(2) The emergency notice requirements of Section 302 of EPCRA;

(3) The list of Safety Data Sheets required by Section 311 of EPCRA;

(4) The emergency and hazardous chemical inventory forms of Section 312 of EPCRA; and

(5) The toxic chemical release inventory of Section 313 of EPCRA, which includes the reduction and recycling information required by Section 6607 of the Pollution Prevention Act of 1990.

1.2.3 Safety Data Sheets (SDS)

Fifteen (15) working days prior to bringing hazardous materials onto Offutt AFB the Contractor shall submit the Safety Data Sheets and usage information on all hazardous materials they (including all Sub-Contractors) intend to use throughout the life of the contract. The COR/KORS will review the information with the Environmental Element.

1.2.4 Storage and Handling

All hazardous materials shall be stored and handled in accordance with all Occupational Safety and Health Administration (OSHA) and National Fire Prevention Association (NFPA) requirements. In addition to those requirements, all storage and staging areas shall be provided with secondary containment and shall be located away from traffic areas and protected from any incursion into the area that could damage the containers or cause a spill. Secondary containment shall be provided by the Contractor to contain at least 110% of the volume of the largest container stored so as to contain any spills or leaks. When stored outdoors, all hazardous materials shall be covered to avoid contact with the elements and to keep precipitation from entering the secondary containment structure.

A Hazardous Material Storage Plan shall be submitted for approval by the Government from the Environmental Element prior to beginning any project. Upon Government approval, a copy shall be kept on site and available at all times.

1.2.5 Spill Reporting

The Contractor responsible shall immediately report all spills (typically greater than two feet in any linear direction and unplanned, on soil, or enter a stormwater inlet or stormwater drainage ditch) by calling 911 and you will be placed in contact with the Offutt AFB Fire Department at 402-294-3582.

The report shall include the following information:

• Identification of the hazardous material spilled

• Injuries that require medical attention

01 57 19-3

• Location of release

• Material released

• Time of release

• Cause of release

• Amount released

• Corrective actions taken

Note, the Contractor responsible and their personnel will clean up the spill and will pay for cleanup materials, potential waste analysis characterization, waste containers, and proper disposal typically through the Defense Logistics Agency (DLA). The project COR/KOR will provide spill cleanup oversight.

A written report containing the same information as the verbal report shall be submitted to 55 CES/CEIE immediately. The Contractor is responsible for the cost of all clean up associated with any release. The Government will file all reports required for environmental regulatory compliance. The Contractor is responsible for the cleanup of all spilled material, including restoration of all areas contaminated by the spill, and for costs incurred by the Government for any assistance or remedial action taken by the Government on behalf of the Contractor. All clean up and restoration shall be done to the satisfaction of the Government. A copy of all clean up and restoration reports shall be submitted for Government recordkeeping via AF Form 66.

Handling and disposal of spill clean-up material shall be in accordance with Paragraph 1.5.4.

1.3 SUBMITTALS

a. Safety Data Sheets (reference paragraph 1.2.3)

b. Hazardous Material Storage Plan (reference paragraph 1.2.4)

c. Spill Reporting (reference paragraph 1.2.5)

d. Contractor Hazardous Request Form (reference paragraph 1.4)

e. Certificate of Hazardous Waste Training (reference paragraph 1.5.1)

f. Waste Analysis Reports (reference paragraph 1.5.4)

g. Request for Disposal (reference paragraph 1.5.4)

h. Test Results (reference paragraph 1.5.4)

i. SPCC Plan (reference paragraph 1.6.2)

j. Petroleum Container Storage Plan (reference paragraph 1.6.2)

k. Report of Waste Water Discharges (reference paragraph 1.7)

l. NPDES Weekly and Post Rain Event Inspection Reports (reference paragraph 1.8)

m. NPDES CSW-NOI Permit and SWPPP (reference paragraph 1.8.1)

n. Project Plan to Control Sediment and Other Contaminants (reference paragraph 1.8.4)

o. NPDES/SWPPP Termination Letter (reference paragraph 1.8.5)

p. NPDES NOI Dewatering Permit (reference paragraph 1.9)

q. NPDES NOI Dewatering Permit Required Reports and Test Results (reference paragraph 1.9)

r. Dewatering Method of Disposal (reference paragraph 1.9)

s. Nonhazardous Solid Waste Diversion Volumes (reference paragraph 1.11)

t. Environmental Training (reference paragraph 1.15)

u. US Army Corps of Engineers Section 404 Permit (reference paragraph 1.16)

1.4 HAZARDOUS MATERIAL AUTHORIZATION - PRIOR TO INSTALLATION ACCESS

Per AFMAN32-7002 para 3.3.3., afman32-7002.pdf 55 CES/CEIE (Environmental Element) Ensures hazardous materials brought onto the installation by contractors via their COR are properly authorized, managed, and tracked, to include completion of appropriate contract close-out actions to remove left-over HAZMAT(s) from the installation. 55 CES/CEIE assists CORs to develop installation-specific contract language procedures. The Contractor shall submit the entire list of potential hazardous chemicals/materials either handwritten; or, in Word or Excel format through the COR. 30 days prior to any construction activity, the COR will submit a copy of the Contractor Hazardous Material List and current Safety Data Sheets to the Environmental Office for authorization and assignment of a government hazmat tracking database number within the Enterprise Environmental, Safety and Occupational Health – Management Information System (EESOH-MIS). Once authorized, the Environmental Office will return the authorized list back to the COR.

For convenience only, the Contractor may utilize the Contractor HAZMAT Request form provided at the end of this document pg. 01 57 19-17.

01 57 19-4

FAR Clause 52.223-3 Hazardous Material and Material Safety Data Identification states as follows:

(a) Hazardous material, as used in this clause, includes any material defined as hazardous under the latest version of Federal Standard No. 313 (including revisions adopted during the term of the contract).

(b) The offeror must list any hazardous material, as defined in paragraph (a) of this clause, to be delivered under this contract. The hazardous material shall be properly identified and include any applicable identification number, such as National Stock Number or Special Item Number. This information shall also be included on the Safety Data Sheet submitted under this contract.

(c) This list must be updated during performance of the contract whenever the Contractor determines that any other material to be delivered under this contract is hazardous.

1.5 DISPOSAL OF REGULATED WASTES

The Contractor shall comply with all current Air Force, Department of Defense, Federal, State and local laws, regulations, policies and permits concerning the proper handling, accumulation, and disposal of regulated wastes. These include, but are not limited to:

• Title 40 Code of Federal Regulations (CFR) Parts 260/282 (40 CFR 260-282) Federal solid and hazardous waste regulations.

• Title 49 Code of Federal Regulations (CFR) Parts 171-173 (49 CFR 171-173) Federal transportation regulations.

• Title 40 Code of Federal Regulations (CFR) Part 112 (40 CFR 112) Spill Prevention Control and Countermeasure Plan

• State of Nebraska Administrative Code Title 128 State solid and hazardous waste regulations.

• City of Omaha Code Chapter 31 City of Omaha sewer standards

• Offutt AFB Hazardous Waste Management Plan Summarizes the hazardous waste accumulation and storage requirements.

1.5.1 Hazardous Waste Training

The Contractor is responsible for ensuring all contract personnel who handle or are exposed to hazardous waste are trained in accordance with applicable regulations and requirements. The Contractor shall maintain hazardous waste training records for all contract personnel. These records will be maintained at the jobsite and available to Government personnel upon request.

1.5.2 Accumulation, Storage, and Sampling Wastes

Contractor activities that generate hazardous waste must operate a Satellite Accumulation Point (SAP) for the collection of wastes. The IAP must have its citing approved by the Government (Offutt Fire Department, Ground Safety, Bioenvironmental Engineering and Environmental Compliance). The operation of the IAP must conform to 40 CFR 262.15 and the Offutt AFB Hazardous Waste Management Plan (HWMP). Waste sampling shall be accomplished by the Contractor at an accredited laboratory at no additional cost to the Government. Waste analysis records shall be maintained by the Contractor and forwarded to the Government. Waste accumulated at the IAP shall be correctly disposed of by the contractor. No contractor waste is to be left behind. Contractor waste shall not be left behind to include partially used or unused Hazardous Materials, even if they plan to return to a similar project at a later time during the year or the following years. The contractor will be contacted to remove and dispose of the same at their expense.

1.5.3 Containers and Containment

The Contractor shall supply all waste storage containers, which shall be new or refurbished and labeled as Department of Transportation (DOT) approved. Containers shall be compatible with the material/waste stored in them. Secondary containment, as required in Paragraph 2.4, for all containers shall be provided by the Contractor. All additional storage and handling requirements of the Offutt AFB HWMP shall be followed.

01 57 19-5

1.5.4 Disposal Procedures

The Contractor shall dispose of all hazardous wastes in accordance with all current applicable regulations and policies. Waste Analysis Reports, including but not limited to, sampling results, safety data sheets and waste stream information will be provided to the Government via AF Form 66. Waste may not be accumulated in excess of 55 gallons.

Fluorescent lamps, bulbs, and all batteries except lead acid (recycled) may be reused by base facility users if still in working condition; otherwise, these items are considered a Universal Waste and must be removed from equipment or fixtures and placed in an approved container for proper disposal through a Universal Waste handler and disposal facility. Note, Universal Waste items cannot go in a solid waste dumpster or landfill.

Prohibited wastes are liquids or liquids containing solids that are prohibited by the City of Omaha Code from being disposed of to the sanitary sewer. The Contractor shall submit test results for the Government to determine proper disposal.

Special waste (e.g. fuel-contaminated soil) is waste which may be disposed of at specially designated landfills, with the landfill's prior approval. The Contractor must submit a Request for Disposal at the landfill along with any landfill-required Testing Analysis and receive Government approval for disposal of special wastes to a landfill. The Contractor is responsible for all costs associated with disposal of special wastes.

Non-regulated waste shall be disposed of at a Nebraska Department of Water, Environmental, & Energy (NDWEE) approved landfill. The Contractor is responsible for all costs associated with the disposal of non-regulated wastes.

1.5.5 Soil Relocation and Analysis

Any soil not placed in the same excavated location must be sampled for the following parameters as follows:

• EPA Method 8015 - Total Extractable Hydrocarbons

• EPA Method 3050B - Barium

• EPA Method 8260D - Volatile Organic Compounds by GC/MS

• EPA Method 8270E - Semi-volatile Organic compounds by TCLP

• EPA Method OA-2 Iowa (or equivalent) - Extractable Petroleum Hydrocarbons (GC)

• EPA Method 6010C - Metals (ICP) - TCLP

• EPA Method 7470 - Mercury (CVAA) - TCLP

• EPA Method 1633 - 40 PFAS Compounds

1.6 SPILL PREVENTION CONTROL AND COUNTERMEASURES (SPCC) PLAN

1.6.1 Condition of Equipment

All Contractor equipment (including containers and vehicles) shall be kept in good condition while on Offutt AFB property. Any equipment found leaking or dripping any hazardous material shall be taken out of service immediately until repaired and all spilled material shall be cleaned up in accordance with the requirements of Paragraph 1.2.5.

1.6.2 SPCC Plan

The Contractor is responsible for handling, using, and storing all regulated petroleum oil (including fuel) on the facility in accordance with the requirements of 40 CFR 112 and Offutt’s Integrated Contingency Plan (ICP).

Prior to bringing any petroleum storage container on base the Contractor shall submit certification for Government approval that the owner of the container has in-place a Spill Prevention Control and Countermeasures (SPCC) Plan in accordance with 40 CFR 112 and that the container is a part of that plan.

The Contractor shall submit a Petroleum Container Storage Plan for Government approval prior to transporting or storing any petroleum-based products on Offutt AFB. The plan shall include the following information:

(a) Site plan with the location of containers

(b) Capacity of each container

(c) Contents of each container

(d) Containers must have secondary containment that will contain at least 110% of the capacity of the

01 57 19-6 container. If secondary containment is not available, the container must be labeled with a certification that it has passed integrity testing performed in accordance with 40 CFR 112 within the past two years.

(e) List (type and quantity) of spill control and clean-up materials in sufficient quantity to contain and clean up the quantity of regulated petroleum products stored, and

(f) Certification that the tanks meet the following requirements:

• The capacity of the tank shall not exceed 12,000 gal (45,420 L).

• All piping connections to the tank shall be made above the normal maximum liquid level.

• Means shall be provided to prevent the release of liquid from the tank by siphon flow.

• Means shall be provided for determining the level of liquid in the tank. This means it should be accessible to the delivery operator.

• As a minimum, all fuel storage tanks shall have as a minimum a functioning fuel level site gauge, when the fuel storage tank reaches about 90 percent full by visual observation, the person responsible for issuing fuel shall stop further fueling processes for that storage tank. Otherwise, a means shall be provided to prevent overfilling by sounding an alarm when the liquid level in the tank reaches 90 percent of capacity and by automatically stopping delivery of liquid to the tank when the liquid level in the tank reaches 95 percent of capacity. In no case shall these provisions restrict or interfere with the proper functioning of the normal vent or the emergency vent.

1.6.1.2 Automatic Tank Gauging System(s) for USTs

Owners/operators of underground storage tanks (USTs) with an automatic tank gauging system (ATGS) shall report any alarm that cannot be cleared to 55 CES/CEIE - environmental compliance office within duty hours or the next duty day. In turn, 55 CES/CEIE will notify the Nebraska state fire marshals (SFM) office regarding this alarm failure. In the event this ATGS alarm cannot be cleared, and a loss of product is confirmed, tank owner/operators must call “4911” and report a spill to the 55 CES/CEF - Offutt AFB fire department.

1.7 WASTEWATER DISCHARGES

The Contractor shall not discharge any wastewater onto “the ground” or into any Waters of the State (including all storm water inlets and open drainage ditches) unless expressly permitted to do so by NDWEE and 55 CES/CEIE. Request for wastewater discharge to the “sanitary sewer” must first be coordinated and approved through 55 CES/CEIE at (402) 294-4087, weblink: C:\Users\1150063961C\OneDrive - United States Air Force\ENGv2\03. CEI\CEIE\CEIEC\WATER Quality\02 - Waste\11-DISCHARGE TO SANITARY.

. Any release of wastewater onto the ground or into Waters of the State (including all storm water inlets and open drainage ditches) from Offutt’s sanitary sewer collection system shall be immediately reported to the Government via the Environmental Element at 402-294-4087 during duty hours or 402-650-5685 after duty hours for emergent issues.

The report shall include the following information:

• Location of release

• Time of release

• Cause of release

• Amount released

• Corrective actions taken

The Contractor is responsible for the cost of all clean up associated with any release. A written report containing the same information as the verbal report shall be submitted for Government records within 24-hours of the release.

1.8 NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM (NPDES) PERMITS FOR

CONSTRUCTION ACTIVITIES

Construction activities (including other land-disturbing activities) that disturb one (1) acre or more are regulated under the NPDES storm water program and require a NPDES Permit for Storm Water Discharges from a Construction Site. This includes smaller sites that are part of a larger common plan of development that will or has the potential to disturb ground and cause sedimentation to nearby stormwater inlets and flow paths. The Contractor is responsible for all material and labor costs associated with the required permit and/or placing stormwater sediment controls even when a construction storm water permit is not required. A

01 57 19-7 copy of the standard permit for construction sites is available on the NDWEE web site. The Contractor shall submit to the Government all Weekly Inspection Reports as well as required inspections after rain events in .pdf format and upload to a log on the required website submittal system. Note that where state and Environmental Protection Agency (EPA) guidelines conflict, the more stringent shall apply on federal installations.

1.8.1 Permit Application

Operators of regulated construction sites equal to or greater than one (1) acre are required to obtain permit coverage from the Nebraska Department of Water, Environmental, and Energy (NDWEE) and to develop and implement a Storm Water Pollution Prevention Plan (SWPPP) in accordance with the permit. A copy of the Construction Storm Water - Notice of Intent (CSW-NOI) submittal and the SWPPP required by NDWEE shall be submitted for approval by the Government to the Environmental Element prior to beginning any project.

Upon approval from the Government and receipt of the CSW Permit issued by NDWEE, a copy shall be submitted to the Government for recordkeeping and a copy shall be kept on site and available at all times.

1.8.2 Storm Water Pollution Prevention Plan (SWPPP) for State-regulated sites.

In addition to the NPDES requirements in the SWPPP, the following items shall also be addressed:

• Spill prevention and control for materials and wastes,

• Construction debris and litter management,

• Concrete waste management (including rinsing concrete from trucks),

• Sanitary/septic waste management,

• Liquid waste management.

Contractors shall use the EPA SWPPP Template available at https://www.epa.gov/npdes/construction-general-permit-resources-tools-and-templates for all SWPPP submittals, and Contractors shall reference the City of Omaha storm water website, www.omahastormwater.org and the Omaha Regional Storm Water Design Manual, http://omahastormwater.org/orsdm/ in their preparation. SWPPP samples and guides are available at these websites, and additional questions regarding the creation and approval of the SWPPP should be directed via the COR or 55 CONS to the Environmental Element’s Storm Water Program Manager at 402-294-4087 during duty hours or 785-221-3404 after duty hours for emergent issues.

Prior to beginning construction, the Contractor shall have both a NDWEE CSW-NPDES Permit and approval of the SWPPP from the Government.

1.8.3 Grading and Erosion Control

Temporary and permanent structural practices shall be installed in accordance with the City of Omaha Soil Erosion and Sediment Control Manual (copies available from the city of Omaha Public Works Department) and maintained in accordance with the issued NPDES permit requirements to eliminate sediment and other contaminants from leaving the construction site.

Documentation of all inspections required by the permit shall be kept on site in accordance with the permit and copies of all documentation shall be submitted for Government recordkeeping within two (2) days of the completion of the document. Any deficiencies with the SWPPP discovered during the course of the project shall be corrected immediately.

1.8.4 Construction Activities Less Than One Acre

Beyond industry standard best management practices, construction activities that disturb less than one acre normally do not require any special plans or submittals. The Government, at its discretion, reserves the right to require a submittal for Government approval of a project plan addressing the installation and maintenance of temporary and permanent structural devices and practices (conforming to the City of Omaha Soil Erosion and Sediment Control Manual) to eliminate sediment and other contaminants from leaving the construction site. If the Government requires this plan, the Contractor shall have 30 days to complete submission to the Government and inspections of the control structures are required at the same frequency as if a permit was received from the State of Nebraska.

https://www.epa.gov/npdes/construction-general-permit-resources-tools-and-templates https://www.epa.gov/npdes/construction-general-permit-resources-tools-and-templates http://www.omahastormwater.org/ http://omahastormwater.org/orsdm/

01 57 19-8

1.8.5 EPA Construction Stormwater Training

Offutt AFB construction projects require EPA stormwater training or equivalent training for project PMs and individuals responsible for maintaining stormwater BMPs (silt fencing, wattles, check dams, etc). Completed stormwater training certificates must be available upon request by federal, state, and local stormwater compliance assessors.

EPA Construction Inspection Training Course (five modules) at weblink:

https://www.epa.gov/npdes/construction-inspection-training-course

1.8.5.1 Non-EPA Construction Stormwater Inspector Trainings

Weblink as follows: https://www.epa.gov/npdes/construction-general-permit-inspector-training

There are a number of existing state and third-party stormwater courses that offer alternatives to the inspector training program provided by EPA for the 2022 CGP. If the non-EPA course covers the minimum topics listed in Part 6.3.b of the CGP, an individual completing the course and having an up-to-date certification of completion can rely on the course to comply with the CGP’s requirements. EPA's review of the following non- EPA training programs found that the course materials appeared to address these minimum topics:

There are a number of existing state and third-party stormwater courses that offer alternatives to the inspector training program provided by EPA for the 2022 CGP. If the non-EPA course covers the minimum topics listed in Part 6.3.b of the CGP, an individual completing the course and having an up-to-date certification of completion can rely on the course to comply with the CGP’s requirements. EPA's review of the following non- EPA training programs found that the course materials appeared to address these minimum topics:

Training Provider Specific Training Name

Alaska Certified Erosion & Sediment Control Lead

Alaska Certified Erosion & Sediment Control Lead (AK-CESCL) Training Program

CISEC Inc. Certified Inspector of Sediment and Erosion Control (CISEC)

CWT Training Academy Construction Activity Stormwater Manager (CASM)

Envirocert Certified Erosion, Sediment, & Storm Water Inspector (CESSWI)

Florida Department of Environmental Protection

Florida Stormwater, Erosion, and Sedimentation Control Inspector (FSESCI) Program

Kansas State University Polytechnic Campus

Construction Stormwater Training

National Stormwater Center Certified Stormwater Inspector Construction (CSI-Construction)

StormwaterONE Qualified Compliance Inspector of Stormwater (QCIS)

StormwaterONE Qualified Preparer of Stormwater Pollution Prevention Plans (QPSWPPP) (also includes QCIS)

University of Minnesota Erosion and Stormwater Management Certification Program Construction Site Management Certification and Recertification

Because EPA does not recommend or endorse individual products or vendors, EPA's reference to the above training programs does not constitute an Agency approval of any individual course, or any broader Agency recognition beyond having addressed the required minimum topics in CGP Part 6.3.b. EPA may update this list from time to time as it learns of additional training programs that may meet the CGP Part 6.3.b requirements. If you are aware of any training programs not listed here that you believe satisfy these requirements, you may contact EPA to provide information for the Agency’s consideration.

Note: If one of the minimum training topics from the CGP Part 6.3.b list (e.g., installation and maintenance of pollution prevention practices) is not covered by a non-EPA training program, you may consider supplementing that training program with the analogous module of the EPA course (e.g., Module 4) that covers the missing minimum training topic.

https://www.epa.gov/npdes/construction-inspection-training-course https://www.epa.gov/npdes/construction-general-permit-inspector-training http://www.ak-cescl.com/ http://www.ak-cescl.com/ https://cisecinc.org/ https://www.cwtacademy.com/wus0118 https://envirocertintl.org/cesswi/ https://floridadep.gov/dear/florida-stormwater-erosion https://floridadep.gov/dear/florida-stormwater-erosion https://polytechnic.k-state.edu/research-training/training-professional-development/certified-inspector-training/courses/construction-stormwater-training.html https://npdes.com/class-descriptions/csi-construction-2day https://stormwaterone.com/erosion-control https://stormwaterone.com/storm-water-pollution-prevention-plans-and-stormwater-management-plans https://stormwaterone.com/storm-water-pollution-prevention-plans-and-stormwater-management-plans https://erosion.umn.edu/courses-registration https://erosion.umn.edu/courses-registration

01 57 19-9

1.8.6 NPDES / SWPPP Termination Letter

Per the State of Nebraska requirements, termination of the permit is required in writing at the completion of construction. A copy of the Contractor’s letter to the state and the State’s response shall be submitted to the Government. If the site is less than 1 acre and a State permit is not required, the Contractor shall submit a letter to the Government terminating their SWPPP.

1.9 NPDES PERMIT FOR DEWATERING OPERATIONS

All dewatering operations (including, but not limited to, pumping from an excavation, lowering the groundwater level via well points, hydrostatic testing, etc.) require dewatering permits issued by NDWEE. The Contractor is responsible for obtaining and meeting all the requirements of dewatering permits. A copy of the NOI for the Dewatering Permit shall be submitted to the Government for review and approval. No dewatering operation shall occur until a permit has been issued by NDWEE to the Contractor and submitted to the Government for verification. Copies of all reports, inspections, analytical testing, etc. required as part of the permit requirements shall be submitted to the Government within two (2) days of completion. If any of these items are to be submitted to NDWEE, a copy of the submittal letter to NDWEE will accompany the Government submittal. For dewatering in areas with contaminated groundwater, the Contractor shall be responsible for weekly sampling and analysis for priority pollutants (Volatile Organic Chemicals [VOCs] and semi-VOCs, metals, etc.) in accordance with the permit requirements. In addition, the Contractor shall submit for Government approval the Method of Disposal of the water. If analysis indicates contamination levels below the permit limits, the Contractor, upon Government approval, can discharge the water to the storm sewer.

The Contractor shall be responsible for all the material and labor cost associated with the requirements of the permit and discharging the water to either type of sewer based on the weekly analytical results. The Contractor is not responsible for any sewer fees for disposal of effluent from an approved dewatering operation to the sanitary sewer.

1.10 AIR PROGRAM REQUIREMENTS

New equipment install(s) that may use a fuel source, store a fuel source, or evaporation cooling such as a generator with tank, boiler, cooling tower/evaporator, and storage tank must first be coordinated through 55 CES/CEIE, 402-294-4087. The Contractor shall ensure compliance with all current Air Force, Department of Defense, Federal, State and local laws, regulations, instructions, policies and permits, including Nebraska Administrative Code (NAC) Title 129, relating to Air Quality, prior to beginning construction work.

Any questions regarding Air Quality requirements should be directed via 55 CONS or the COR to the Environmental Element’s Air Quality Program Manager at 402-294-4087 during duty hours or 402-650-5685 after duty hours for emergent issues.

The 55 CONS, 55 CE/55 CE CORs to include US Army Corps of Engineers (USAGE) CORs, and their contractors or staff shall apply for a Nebraska of Environment and Energy (NDWEE) Air Quality Construction permit, 30+ days prior to construction, anytime a new or modified generator or cooling tower is installed on Offutt AFB IAW Offutt AFB’s Air Quality (AQ) Synthetic Minor Permit. Also 30+ days prior notification to NDWEE is required IAW title 129/AQ Synthetic Minor Permit before the generator/cooling tower goes online or is tested. The CORs/staff members can keep the Instillation AQ Manager up to date with NDWEE correspondence and decision making during the permitting process. “Air Quality Construction Permits” http://dee.ne.gov/Publica.nsf/pages/05-165 and “What is Potential to Emit (PTE)?”

http://dee.ne.gov/Publica.nsf/pages/18-005. Paper copies of forms and guidance documents are available on request or downloadable via the Department’s website: http://dee.ne.gov/ .

1.11 NONHAZARDOUS SOLID WASTE DIVERSIONS

In keeping with the Air Force solid waste diversion rate goal, the Contractor shall divert at least 50% of the construction and demolition debris generated during the project. The waste may be reused, recycled, sent to a waste-to-energy incinerator, or managed in another approved manner that keeps it from going to a landfill.

The Contractor shall track and report the amount of construction and demolition debris disposed in a landfill, recycled, or sent to a waste-to-energy incinerator each quarter. The following form shall be completed and submitted to the Government no later than the first working day after the end of each quarter (31 Dec, 31 Mar, http://dee.ne.gov/Publica.nsf/pages/05-165 http://dee.ne.gov/Publica.nsf/pages/18-005 http://dee.ne.gov/

01 57 19-10

30 Jun, and 30 Sept of any year). DAFMAN 32-7002 Environmental Compliance and Pollution Prevention, para 6.9.2, Installation civil engineering must ensure weight and cost data for C&D debris diverted and disposed are documented and reported to the Office of the Secretary of Defense in accordance with DoDI 4715.23.

NON-HAZARDOUS SOLID WASTE DIVERSION

1.12 EXCAVATION ENVIRONMENTAL RESPONSE PROCEDURES

In the past, burial /dumping was an industry accepted practice often used to dispose of materials no longer needed or wanted. Accidental spills also occurred periodically. Since the mid-1980’s, the OAFB environmental program has been identifying, investigating, and remediating as necessary, waste disposal and spill sites. During any grading or excavation there is potential to uncover previously unknown waste or spilled material.

Known contaminated sites and groundwater contaminant plumes are identified in Figure 1, below. The areas currently under investigation for PFAS are identified in Figure 2 and highly subject to change since the plume delineation work is on-going. Work affecting soil or groundwater must first be coordinated with the Offutt Environmental Restoration Program Manager (AFCEC/CZOM) located in Building 88 at 402-294-1387.

Contact Information

Name

Phone

Date

Fiscal Year Quarter Q1 =October 1 - December 31 Q2 = January 1 - March 31 Q3= April 1 - June 30 Q4 = July 1 - September 30

Project Name(s) (e.g. construction of Wing Headquarters)

Construction and demolition related solid waste disposal data (Do not include base-wide routine solid waste picked up by BFI)

Total solid waste disposed (cost and tons)

Cost:

Tons:

Construction and demolition related recycling data (Do not include base-wide, routine recycling such as aluminum cans and paper.)

Total recycled (tons and cost)

Cost:

Tons:

Materials recycled (provide cost and tonnage)

Asphalt Cost: Tons:

Concrete Cost: Tons:

Wood scrap Cost: Tons:

Metal Cost: Tons:

Soil Cost: Tons:

Other recycling (Do not include base-wide, routine recycling such as aluminum cans and paper.) Describe and provide tonnage.

Items reused that would otherwise be disposed. Describe and provide tonnage.

01 57 19-11

Response - If the contractor encounters unusual materials* during excavation or grading, the contractors shall:

1. Immediately stop the excavation or grading operation.

2. Shut down the equipment and leave it in its present location.

3. Do not attempt to determine the contents of any bottles, containers, boxes, etc.

4. Withdraw personnel from the equipment and the excavation a distance of at least 50 feet upwind or cross wind or as directed.

5. Contact the escort, inspector, contracting officer or the contracting officer’s designated representative immediately, or call 911.

6. Remain in the area until released by the CO or designated representative.

*Unusual Material - Unusual material as used in this section shall mean any materials other than soils, rock or bedrock encountered during excavation that is not specifically identified as part of the work in the contract document. This includes but is not limited to: stained soils; free product fuels, oils, etc.; suspicious odors;

bottles, cans, drums, or other containers; wooden, metal, or cardboard boxes; rags, gloves, or personal protective equipment; trash or common landfill debris; concrete, concrete block, wood, metal, or other building materials and construction debris; or any other unidentified materials.

Every contractor and subcontractor employee shall be briefed on the response procedures in this section prior to beginning work on OAFB. Training shall be documented by the employee signing and dating a training log sheet. Log sheet shall be maintained on the immediate jobsite in the contractor’s project office and shall be available for inspection by the contracting officer or designated representative. Response procedures review shall be included in the contractor’s periodic safety meetings.

01 57 19-12

01 57 19-13

01 57 19-14

1.13 ARCHEOLOGICAL DISCOVERIES

If archeological discoveries are encountered during construction, the Contractor shall immediately cease operations and report their findings to the COR who will consult with the installation Cultural Resource Manager (CRM) in the Environmental Element at 402-294-4087 during duty hours or 402-650-5685 after duty hours for emergent issues.

1.14 TESTING

The Contractor shall analyze and test environmental samples using standardized methods in current editions of approved testing references such as SW-846, “Test Methods for Evaluating Solid Wastes, Physical/Chemical Methods”; 40 CFR 136, “Guidelines Establishing Test Procedures for the Analysis of Pollutants”; and “Standard Examination of Water and Wastewater”. The Contractor shall ensure the defensibility of test and analytical results through execution of sound scientific principles.

EPA SW-846: https://archive.epa.gov/epawaste/hazard/testmethods/web/html/index-2.html

For soil or water sampling, recommend contacting Midwest Labs, (402) 334-7770, for prepackaged sample containers and cooler to meet EPA SW-846 plus sampling PFAS.

1.15 DUST CONTROL

Control of dust during construction, demolition activities, debris removal and any other activities required as a part of the work under this contract must be thorough and complete. For outdoors construction, dust and/or particulate matter associated with the construction process shall not become airborne in such quantities and concentrations that it remains visible in the ambient air beyond the boundaries of the construction site. Dust control shall be addressed in the Storm Water Pollution Prevention Plan (SWPPP) as required by Section 1.8, above.

1.16 ENVIRONMENTAL MANAGEMENT SYSTEM

The Air Force has implemented an Environmental Management System (EMS). Every contract employee that will physically work on the installation is required to be familiar with and understand the installation Environmental Policy which is posted on Offutt AFB public web page at https://www.offutt.af.mil/Portals/97/Resources/Environmental/EMS%20Tri-fold%202024v2.pdf?ver=KmXIzZbAzyMZCoCMQK7Duw%3d%3d&timestamp=1719348624502

The acronym P.I.C.K. may be useful in remembering and demonstrating familiarization with this policy. The policy contains overarching commitments that include Pollution Prevention, Improving Continuously, Compliance with applicable environmental laws and policies, and Know how one’s job impacts the environment.

Additionally, every contract employee that will physically work on the installation is required to know the environmental requirements that apply to their duties and receive appropriate environmental training.

In the event the contracting officer determines it to be necessary, the Contractor shall provide proof of completion of such training by employees and subcontractors to the contracting officer.

Publically accessible web-based training is available at no cost at The Environmental Awareness Course Hub, otherwise known as TEACH, (https://usaf.learningbuilder.com).

1.17 JURISDICTIONAL WETLANDS

The Contractor shall obtain approval from the Government prior to conducting any work in, or potentially impacting, a ditch, stream, or other body of water which may be classified as a jurisdictional wetland on Offutt AFB property, per 33 CFR 328 and 40 CFR 230 Section 404(b). If the area is deemed to be a jurisdictional wetland, a section 404(b) permit must be obtained by the Contractor from the US Army Corps of Engineers prior to the start of any work. If applicable, a copy shall be submitted to the Government for recordkeeping and a copy shall be kept on site and available at all times.

https://archive.epa.gov/epawaste/hazard/testmethods/web/html/index-2.html https://www.offutt.af.mil/Portals/97/Resources/Environmental/EMS%20Tri-fold%202024v2.pdf?ver=KmXIzZbAzyMZCoCMQK7Duw%3d%3d&timestamp=1719348624502 https://www.offutt.af.mil/Portals/97/Resources/Environmental/EMS%20Tri-fold%202024v2.pdf?ver=KmXIzZbAzyMZCoCMQK7Duw%3d%3d&timestamp=1719348624502 https://usaf.learningbuilder.com/

01 57 19-15

Wetland maps from a 2009 wetland inventory at Offutt AFB can be found at Appendix E of the Integrated Natural Resources Management Plan at:

https://usaf.dps.mil/teams/10624/Offutt/Shared%20Documents/Natural%20Resources%20(NR)/2020%20INR MP%205-Year%20Review_Completed%20Signatures.pdf The National Wetlands Inventory (NWI) is contained on maps produced by the USFWS of the Department of the Interior.

1.18 RADIOACTIVE SOURCES

AFMAN 40-201 para 2.19. Requiring Activities (for contractor work), shall:

2.19.1. Coordinate with the IRSO to obtain information necessary to develop a Performance Work Statement/Statement of Work for compliance with all applicable statutes, regulations and instructions for managing RAM in the USAF. (T-1).

2.19.2. Ensure, as appropriate, the Performance Work Statement/Statement of Work includes the requirement for the contractor to submit: (T-0).

2.19.2.1. An NRC or Agreement State license. (T-0). For those areas of exclusive Federal jurisdiction, a copy of both the NRC Form 241, Report of Proposed Activities in NonAgreement States, Areas of Exclusive Jurisdiction or Offshore Waters, and Agreement State license must be submitted. (T-0). For those areas of concurrent or proprietary jurisdiction in an agreement state, the respective Agreement State license is a valid authorization; or

2.19.2.2. A valid NRC Master Materials License-issued RAM permit from the US Navy or Veterans Affairs (T-0). Note: The Navy, Veterans Affairs, and AF are the only entities that hold a NRC Master Materials License which can issue permits; 2.19.2.3. Written certification from DOE organizations or DOE prime contractors that they are exempt from NRC license requirements; and (T-0).

2.19.2.4. Written approval from the IRSO to transfer, transport, or use temporary storage areas for RAM on the installation. (T-1).

Any Contractor that will bring any "Radioactive Sources" that require NRC or State radioactive materials permit license onto Offutt AFB property must have prior written approval from the Offutt AFB Radiation Safety Officer (RSO), located in the Bioenvironmental Engineering Flight. The RSO can be reached at (402) 294- 6319. A copy of the written permission shall be always kept on site and available.

Contractor must provide the following documentation, which is necessary for bioenvironmental engineering to provide a written authorization for licensed radioactive materials on base:

- Company, POC, address, and phone number of the prime contractor for the project

- Company, name, and phone number of the person responsible for overseeing operations involving the licensed radioactive material

- Location of the base work site, include contract number

- Location where the source will be stored, if on base, on weekends, holidays, and after duty hours

- Description of the radioactive sources (isotope and activity)

- Name, organization, POC, and phone number of the AF (DoD) contract monitor

- Dates (start and finish dates) when the radioactive sources will be on base

- Copy of the Radioactive Material License for the sources coming on base

- Copy of contractor’s radiation safety plan

- Copy of hazardous materials shipping paper

- Copy of contractor’s radioactive materials emergency action plan

- List of authorized users of the radioactive sources

- Inventory of the radioactive sources being used

- Latest leak test results for the sources being brought on base https://usaf.dps.mil/teams/10624/Offutt/Shared%20Documents/Natural%20Resources%20(NR)/2020%20INRMP%205-Year%20Review_Completed%20Signatures.pdf https://usaf.dps.mil/teams/10624/Offutt/Shared%20Documents/Natural%20Resources%20(NR)/2020%20INRMP%205-Year%20Review_Completed%20Signatures.pdf

01 57 19-16

1.19 REGULATORY INSPECTIONS

The Contractor shall immediate report inform regulatory inspections to the Environmental Element office, 55 CES/CEIE, at 294-4087 that is coordinated through the Contracting Officer’s Representative assigned to the project. Written notices of noncompliance from regulatory agencies are reported in accordance with AFI 32- 7001, paragraphs 2.31.10 and 2.31.11.

1.20 ENDOPHYTE FESCUE GRASS IMPLEMENTATION

Within runway security fencing and where possible at the end of runways, Endophyte fescue grass MUST be utilized to reduce potential aircraft bird air strikes.

1.21 BUILDING FOUNDATION AND TERMITE CONTROL

During new building construction and any alterations near existing building foundations must utilize Fipronil pesticide to maintain a permanent continuous barrier necessary to prevent termite infestation. Reference DoDI 4150.07 DoD Pest Management Program, effective 26 Dec 2019, para 1.2 Policy. The DoD: c. Uses AFPMB-approved, Environmental Protection Agency (EPA)-registered pesticides applied by trained and certified pesticide applicators. https://www.esd.whs.mil/portals/54/documents/dd/issuances/dodi/415007p.pdf

Note, Premise isn’t on the DoD Approved Insecticide list.

https://extranet.acq.osd.mil/eie/afpmb/cac/standardlists/DOD_PEST_MANAGEMENT_MATERIAL_LIST.pdf

Reference DoDI 4150.07, Vol 1, 22 Jan 2020, Section 4.3 PEST MANAGEMENT MATERIEL PESTICIDE ACQUASITION, b. After receiving Pest Management Consultant approval, authorities may locally procure pest management materiel that complies with applicable federal, State, local, and HN requirements if that procurement is in response to an emergency or a unique local situation, or when the materiel is to be used in such small quantities that NSN assignment is not feasible.

https://www.esd.whs.mil/Portals/54/Documents/DD/issuances/dodm/415007_vol1.pdf?ver=2020-01-22- 132922-467

UFGS-31 31 16.13, Aug 2022, Part 1 General, modification of this section, including materials, concentrations, or rates of application, which are considered necessary because climatic conditions, porosity of soil to be treated, type of termite, or heavy infestation of termites, will be in accordance with the guidance contained in the installation pest integrated management plan.

1.22 ALL STORAGE TANKS THAT WILL CONTAIN OIL/FEUL, 55 GALLON AND LARGER

Requirement. NE Title 153 Chapter 7 (dated 31 Dec 1991) and NE Title 158.

New tanks must first be coordinated through 55 CES/CEIE, 402-294-4087. Reference weblinks below, complete Nebraska state fire marshal (SFM) storage tank installation application forms, $50 application fee, and storage tank…

This is the start of the file's text. The full file is on GovTribe.

File details come from the government source that posted it. Updated .