Statement_of_work_2.DOCX

1. Power Soak Model No. POWER SOAK with custom fit (length available is approximately 255”)

LEFT TO RIGHT X 34" FRONT TO BACK AS FOLLOWS:

2" left end splash (finished) 123" soiled drainboard (with cut‐out for scrap collector) 36" wash tank x 21" deep (with sheet pan racks) 24" rinse sink x 14" 24" sanitize sink x 14" 42" clean drainboard 2" right end splash (finished) To consist of the following details:

1 ea POWERSOAK‐PSK POWERSOAK 1 ea ub‐s34‐jbz‐psk gen 3 utensil basket jbz 1 ea ws‐36‐21‐28.75‐g3‐l‐psk 36" gen‐3 wash sink, 21" deep 1 ea width‐34‐psk standard 34 inches front to back system 35 inch a deck‐height‐psk deck height 1 ea ss‐24‐14‐28.75‐l‐psk 24" wide sanitizer sink, 14" deep 1 ea dc‐psk disposer cone, includes control panel bracket and welding 1 ea sdb‐48‐34‐psk 43‐48" soiled drain board 1 ea bes‐f‐l‐sld‐34‐psk 2" backsplash‐style end splash with filled end, soiled left...

1 ea rs‐24‐14‐28.75‐l‐psk 24" wide rinse sink, 14" deep 1 ea cdb‐42‐34‐psk 37‐42" clean drain board 1 ea bes‐r‐cln‐34‐psk 2" backsplash‐style end splash, clean right end 1 ea ps‐200‐h‐3ph‐208v‐2hp‐l‐psk ps‐200 208v/3ph control with automatic wash tank heat 3 ea drebv‐psk drain ball valve rear outlet 1 ea pr‐1‐psk pre‐rinse 1/2" spray valve 2 ea hff‐wm‐psk 3/4" high flow faucet wall‐mount t&s #bf‐0299‐ps 1 ea 123” cdb‐xx‐psk custom drainboard 1 ea sprs‐36‐l‐psk gen 3 sheet pan rack system for a 36" wash tank

2. Waste Collector: Salvajor Model No. P914 Pot/Pan Scrap Collector™, scrapping, pre‐flushing & collecting system (widely accepted in areas where disposers are restricted), NEMA 4 HYDROLOGIC® control panel with patented operator sensor, two water saving modes (timed run & auto start/stop), safety line disconnect, LCD readout, salvage basin & silverware trap, scrap basket, 3/4 HP corrosion‐resistant pump, pump intake screen, stainless steel construction, UL, CSA, CE, NSF. Custom collector top. Include 1 additional scrap basin (992011) and scrap basket (992013).

Power requirement: 208v/60/3‐ph, 3.2 amps

3. INSTALLATION: Complete all necessary work to remove the existing sink, disposer, and any other items necessary to prepare for new equipment installation (leave the wall cladding and shelf). Move existing equipment to location specified by facility manager to remain government property.

Install new power soaker with scraper, assemble table and seal, and make all final connections to utilities. Dispose of all debris in facility supplied container. Complete any other work necessary for new equipment to function as designed. Start up and test for proper operation. Provide an initial operations demonstration and submit any necessary paperwork to begin the warranty coverage period for all equipment. Provide manuals and warranty information to the facility manager. All finalized equipment and installation must be safe to use in a commercial kitchen setting.

Supplier will be responsible for obtaining advance approval of installation dates. Equipment may be stored on site up to 72 hours prior to install. Supplier will retain ownership/responsibility for all equipment until installation is complete. Supplier will be responsible for unloading and moving equipment as necessary to complete installation.