Attachment_1_-_Statement_of_Work_-_PMB_Extended_Svs.pdf

Attachment 1 Solicitation # FA3022-18-Q-0017

STATEMENT OF WORK

OF

PERIODIC MAINTENANCE OF PLASTIC MEDIA BLASTING EQUIPMENT

AT

COLUMBUS AFB, MS

FY19

1 August 2018

REQUIREMENTS:

• Require a 1 year, plus 4 option years, contract for a service provider to provide all tools, labor, material, and transportation and disposal required to perform periodic preventive maintenance on the PMB equipment located in building 414 as required, but not to exceed, the stated intervals of this SOW.

• The contractor shall remove the used oil/air filter elements from the properly supported positions respective to the type of filter elements and replace and install new filter elements to their properly supported positions respective to the type of element.

• The contractor is also responsible for all shipping costs to Columbus AFB.

• The contractor shall perform this service in accordance with this Statement of Work and adhere to all LOCAL, STATE and FEDERAL regulations that apply while performing this service.

• Upon the first year of a contract award a service of each serviceable item will be accomplished to baseline all servicing schedules.

BUILDING REQUESTED INTERVAL

LOCATION SERVICE OF SERVICE

414 3-Week Interval Services:

Clean SIMCO-ION Blue Bar HL Static Neutralizer 3 Wks

Monthly-Interval Services:

Dust Collector Inspect inside dust collector for worn cartridges Monthly

Inspect inside of dust collector for moisture Monthly Check dust collector bearing lubrication Monthly Verify operation of dust collector pulse Monthly Heavy Particle Separator Inspect feed control/air control rods inside hood/remove build-up Monthly Inspect ducting and inspect for wear Monthly Inspect deck for wear and blockage Monthly Inspect and adjust drive belts Monthly Inspect shaft bearings Monthly

Attachment 1 Solicitation # FA3022-18-Q-0017

3-Month Interval Services:

Pneumatic Recovery and Storage Equipment

Inspect wear plate and inside of reclaimer for wear/replace if req’d 3 Mos.

Inspect reclaimer door gasket for wear and damage/replace if req’d 3 Mos.

Inspect wear plate in transition elbow for wear 3 Mos.

Bucket Elevator Lubricate all idler bearings 3 Mos.

Inspect upper/lower pulleys for wear/replace if req’d 3 Mos.

Abrasive Cleaner Lubricate idler bearing 3 Mos Rotary Airlock Inspect rotors and rotor tips/check clearance 3 Mos Lubricate gearbox (speed reducer) as required 3 Mos Lubricate main motor drive and non-drive end bearings 2000 Hrs/3 Mos

6-Month Interval Services:

Rebuild condensate solenoid valves using field kits 4000 Hrs./6 Mos.

Inspect blowdown silencers and replace if necessary 4000 Hrs./6 Mos.

Clean gearcase breather 4000 Hrs./6 Mos.

Check calibration of pressure transducers 6 Mos.

Change air filter element 6 Mos.

1-Year Interval Services:

Inspect starter contactors 8000 Hrs./1 Yr.

Replace check valve seat and spring using field kit 8000 Hrs./1 Yr.

Rebuild blowdown valve using field kit 8000 Hrs./1 Yr.

Clean condensate strainers 8000 Hrs./1 Yr.

Change lubricating oil and filter element 8000 Hrs./1 Yr.

Fully inspect condensate separators/external surfaces/fittings 8000 Hrs./1 Yr.

Remove safety valves from compressor, inspect and recalibrate 1 Yr.

2-Year Interval Services:

Rebuild hydraulic cylinder using field kit 16000 Hrs./2 Yr.

4-Year Interval Services:

Replace all hoses 4 Yrs.

5-Year Interval Services:

Replace discharge check valve 40000 Hrs./5 Yr.

LOCATION SERVICE OF SERVICE