Attch_1_Salient_Characteristics.pdf

Attachment 1

Requirements for Tunable YIG Filters: 0001

1. 40-MHz Ku-Band Downlink YIG Filter

a. Representative Products (or equivalent):

i. Micro Lambda Wireless – MLFP-1665PA

ii. OmniYIG – M3171D

b. Tunable YIG Filter:

i. Tuning Bandwidth: 10.95 GHz to 12.75 GHz

ii. 3-dB Filter Bandwidth: 35 MHz min, 45 MHz max, across tuning bandwidth

iii. Number of Filter Stages: 4 poles/stages min, 6 poles/stages max

iv. Insertion Loss: 7 dB max

v. Power Limiting Level: +5 dBm min

vi. Thermal Effects: Minimum variation in tuned center frequency with temperature

c. Connectors:

i. SMA Male or 3.5-mm Male connectors, both input & output

d. Control:

i. Integrated Analog Driver for YIG Filter

ii. 0-10 Volt DC Control Voltage Range

1. 0 V: Lower end of tuning range (10.95 GHz)

2. 10 V: Upper end of tuning range (12.75 GHz)

e. Electrical:

i. DC Power Supplies Available: +24V (heater), +15V / -15V (YIG driver)

ii. Interface: single DB-9 connector for all power and control connections

f. Mechanical:

i. Form Factor: 3.1” long, 1.7” wide, 2.0” height, excluding connectors (max)

ii. Mounting Holes: 6-32 tapped mounting holes on 1.8” x 1.3” pattern

2. 80-MHz Ku-Band Downlink YIG Filter

a. Representative Products (or equivalent):

i. Micro Lambda Wireless – MLFP-1666PA

ii. OmniYIG – M3172D

b. Tunable YIG Filter:

i. Tuning Bandwidth: 10.95 GHz to 12.75 GHz

ii. 3-dB Filter Bandwidth: 70 MHz min, 90 MHz max, across tuning bandwidth

iii. Number of Filter Stages: 4 poles/stages min, 6 poles/stages max

iv. Insertion Loss: 7 dB max

v. Power Limiting Level: +5 dBm min

vi. Thermal Effects: Minimum variation in tuned center frequency with temperature

c. Connectors:

i. SMA Male or 3.5-mm Male connectors, both input & output

d. Control:

i. Integrated Analog Driver for YIG Filter

ii. 0-10 Volt DC Control Voltage Range

1. 0 V: Lower end of tuning range (10.95 GHz)

2. 10 V: Upper end of tuning range (12.75 GHz)

e. Electrical:

i. DC Power Supplies Available: +24V (heater), +15V / -15V (YIG driver)

ii. Interface: single DB-9 connector for all power and control connections

f. Mechanical:

i. Form Factor: 3.1” long, 1.7” wide, 2.0” height, excluding connectors (max)

ii. Mounting Holes: 6-32 tapped mounting holes on 1.8” x 1.3” pattern

3. 40-MHz C-Band Downlink YIG Filter

a. Representative Products (or equivalent):

i. Micro Lambda Wireless – MLFP-1667PA

ii. OmniYIG – M3181D

b. Tunable YIG Filter:

i. Tuning Bandwidth: 3.6 GHz to 4.2 GHz

ii. 3-dB Filter Bandwidth: 35 MHz min, 45 MHz max, across tuning bandwidth

iii. Number of Filter Stages: 4 poles/stages min, 6 poles/stages max

iv. Insertion Loss: 7 dB max

v. Power Limiting Level: +5 dBm min

vi. Thermal Effects: Minimum variation in tuned center frequency with temperature

c. Connectors:

i. SMA Male or 3.5-mm Male connectors, both input & output

d. Control:

i. Integrated Analog Driver for YIG Filter

ii. 0-10 Volt DC Control Voltage Range

1. 0 V: Lower end of tuning range (3.6 GHz)

2. 10 V: Upper end of tuning range (4.2 GHz)

e. Electrical:

i. DC Power Supplies Available: +24V (heater), +15V / -15V (YIG driver)

ii. Interface: single DB-9 connector for all power and control connections

f. Mechanical:

i. Form Factor: 3.1” long, 1.7” wide, 2.0” height, excluding connectors (max)

ii. Mounting Holes: 6-32 tapped mounting holes on 1.8” x 1.3” pattern

4. 80-MHz C-Band Downlink YIG Filter

a. Representative Products (or equivalent):

i. Micro Lambda Wireless – MLFP-1668PA

ii. OmniYIG – M3182D

b. Tunable YIG Filter:

i. Tuning Bandwidth: 3.6 GHz to 4.2 GHz

ii. 3-dB Filter Bandwidth: 70 MHz min, 90 MHz max, across tuning bandwidth

iii. Number of Filter Stages: 4 poles/stages min, 6 poles/stages max

iv. Insertion Loss: 7 dB max

v. Power Limiting Level: +5 dBm min

vi. Thermal Effects: Minimum variation in tuned center frequency with temperature

c. Connectors:

i. SMA Male or 3.5-mm Male connectors, both input & output

d. Control:

i. Integrated Analog Driver for YIG Filter

ii. 0-10 Volt DC Control Voltage Range

1. 0 V: Lower end of tuning range (3.6 GHz)

2. 10 V: Upper end of tuning range (4.2 GHz)

e. Electrical:

i. DC Power Supplies Available: +24V (heater), +15V / -15V (YIG driver)

ii. Interface: single DB-9 connector for all power and control connections

f. Mechanical:

i. Form Factor: 3.1” long, 1.7” wide, 2.0” height, excluding connectors (max)

ii. Mounting Holes: 6-32 tapped mounting holes on 1.8” x 1.3” pattern

Requirements for Fairview Microwave Components: 0002

1. Fairview Microwave SFI0418 Isolator, or equivalent

a. RF Isolator Specs:

i. Frequency Range: 5.8-14.5 GHz (min)

ii. Isolation: 15 dB (min)

iii. Insertion Loss: 1.5 dB (max)

iv. VSWR: 1.5:1 (max)

v. Power Handling: 1 Watt (min), forward or reverse

vi. Connectors: SMA or 3.5-mm Female Connectors

b. Mechanical:

i. Dimensions: 1.0” wide x 2.6” length x 1.0” height (max), excluding connectors

2. Fairview Microwave SFI3512 Isolator, or equivalent

a. RF Isolator Specs:

i. Frequency Range: 3.6-12.75 GHz (min)

ii. Isolation: 15 dB (min)

iii. Insertion Loss: 2.2 dB (max)

iv. VSWR: 1.5:1 (max)

v. Power Handling: 1 Watt (min), forward or reverse

vi. Connectors: SMA or 3.5-mm Female Connectors

b. Mechanical:

i. Dimensions: 1.2” wide x 2.0” length x 1.0” height (max), excluding connectors

3. Fairview Microwave SFI0818 Isolator, or equivalent

a. RF Isolator Specs:

i. Frequency Range: 8-18 GHz (min)

ii. Isolation: 16 dB (min)

iii. Insertion Loss: 1.0 dB (max)

iv. VSWR: 1.5:1 (max)

v. Power Handling: 1 Watt (min), forward or reverse

vi. Connectors: SMA or 3.5-mm Female Connectors (or one Male / one Female)

b. Mechanical:

i. Dimensions: 0.5” wide x 0.5” length x 0.7” height (max), excluding connectors

4. Fairview Microwave SFI2040 Isolator, or equivalent

a. RF Isolator Specs:

i. Frequency Range: 2-4 GHz (min)

ii. Isolation: 18 dB (min)

iii. Insertion Loss: 0.5 dB (max)

iv. VSWR: 1.35:1 (max)

v. Power Handling: 1 Watt (min), forward or reverse

vi. Connectors: SMA or 3.5-mm Female Connectors (or one Male / one Female)

b. Mechanical:

i. Dimensions: 0.8” wide x 1.3” length x 1.4” height (max), excluding connectors

5. Fairview Microwave SFI1020 Isolator, or equivalent

a. RF Isolator Specs:

i. Frequency Range: 1-2 GHz (min)

ii. Isolation: 19 dB (min)

iii. Insertion Loss: 1 dB (max)

iv. VSWR: 1.4:1 (max)

v. Power Handling: 1 Watt (min), forward or reverse

vi. Connectors: SMA or 3.5-mm Female Connectors (or one Male / one Female)

b. Mechanical:

i. Dimensions: 2.6” wide x 2.5” length x 1.2” height (max), excluding connectors

6. Fairview Microwave MP0218-2 SMA Two-Way RF Power Divider, or equivalent

a. RF Specs:

i. Two-Way Power Divider

ii. Frequency Range: 2-18 GHz (min)

iii. Insertion Loss: 1.2 dB (max)

iv. Isolation: 16 dB (min)

v. Connectors: SMA or 3.5-mm Female Connectors

b. Mechanical:

i. Dimensions: 1” wide x 1.9” length x 0.4” height (max), excluding connector

7. Fairview Microwave MP0208-2 SMA Two-Way RF Power Divider, or equivalent

a. RF Specs:

i. Two-Way Power Divider

ii. Frequency Range: 2-8 GHz (min)

iii. Insertion Loss: 0.6 dB (max)

iv. Isolation: 18 dB (min)

v. Connectors: SMA or 3.5-mm Female Connectors

i. Dimensions: 1.2” wide x 1.2” length x 0.4” height (max), excluding connector

8. Fairview Microwave SA35110SMA Variable Step Attenuator, or equivalent

a. Frequency Range: 0-3 GHz, minimum

b. Attenuation:

i. Range: 0-69 dB (min)

ii. Step Size: 1 dB increments

iii. Manual Control (for example, 10-dB knob & 1-dB knob)

c. Mechanical Configuration:

i. Concentric control knobs, if applicable (if there are separate 10-dB and 1-dB attenuation knobs, they must be concentric)

ii. Bulkhead-mount attenuator – suitable for installation on front panel of test equipment, such that control knobs and the body of the attenuator, with RF connectors, are on opposite sides of the panel to which the attenuator is mounted)

iii. Dimensions:

1. Length of attenuator body not to exceed 4.5” from panel-mounting plane, excluding connectors

2. Diameter of attenuator body not to exceed 1.75”, excluding connectors

d. RF Connectors:

i. SMA or 3.5-mm Female Connectors

9. Fairview Microwave SA18H-1 SMA Attenuators, or equivalent

a. RF Specs:

i. Frequency Range: 0-18 GHz (min)

ii. Insertion Loss: Nominal Attenuation = 1 dB

iii. Connectors: SMA or 3.5-mm Connectors, One Male and One Female

b. Mechanical:

i. Coaxial Insertion Component, 1.1” in Length (max)

10. Fairview Microwave SA18H-3 SMA Attenuators, or equivalent

a. RF Specs:

i. Frequency Range: 0-18 GHz (min)

ii. Insertion Loss: Nominal Attenuation = 3 dB

iii. Connectors: SMA or 3.5-mm Connectors, One Male and One Female

b. Mechanical:

i. Coaxial Insertion Component, 1.1” in Length (max)

11. Fairview Microwave SA18H-5 SMA Attenuators, or equivalent

a. RF Specs:

i. Frequency Range: 0-18 GHz (min)

ii. Insertion Loss: Nominal Attenuation = 5 dB

iii. Connectors: SMA or 3.5-mm Connectors, One Male and One Female

i. Coaxial Insertion Component, 1.1 inch in Length (max)

12. Fairview Microwave SA18H-10 SMA Attenuators, or equivalent

a. RF Specs:

i. Frequency Range: 0-18 GHz (min)

ii. Insertion Loss: Nominal Attenuation = 10 dB

iii. Connectors: SMA or 3.5-mm Connectors, One Male and One Female

b. Mechanical:

i. Coaxial Insertion Component, 1.1 inch in Length (max)

13. Fairview Microwave SA18H-20 SMA Attenuators, or equivalent

a. RF Specs:

i. Frequency Range: 0-18 GHz (min)

ii. Insertion Loss: Nominal Attenuation = 20 dB

iii. Connectors: SMA or 3.5-mm Connectors, One Male and One Female

14. Fairview Microwave SA18H-30 SMA Attenuators, or equivalent

i. Frequency Range: 0-18 GHz (min)

ii. Insertion Loss: Nominal Attenuation = 30 dB

iii. Connectors: SMA or 3.5-mm Connectors, One Male and One Female

15. Fairview Microwave SM4237 N-Type to SMA Adapter, or equivalent

i. Frequency Range: 0-15 GHz (min)

ii. Connectors: N-Type Female and SMA Female

b. Mechanical:

i. Bulkhead-mount coaxial adapter

ii. Preferred: Hermetically sealed

16. Fairview Microwave SM4242 N-Type to SMA Adapter, or equivalent

a. RF Specs:

i. Frequency Range: 0-12 GHz (min)

ii. Connectors: N-Type Female and SMA Female

b. Mechanical:

i. Bulkhead-mount coaxial adapter

ii. Preferred: Hermetically sealed

17. Fairview Microwave ST-SMA3 SMA Fixed Torque Wrench, or equivalent

a. Mechanical:

i. Wrench-Style Torque Wrench

ii. Fixed Torque: 8 in-lbs

iii. Click-Style Torque Indicator (clicks when 8 in-lbs achieved)

iv. 5/16 Drive Suitable for SMA Connectors

18. Fairview Microwave ST-SMA8 SMA Fixed Torque Wrench, or equivalent

a. Mechanical:

i. Screwdriver-Style Torque Wrench

ii. Fixed Torque: 8 in-lbs

iii. Click-Style Torque Indicator (clicks when 8 in-lbs achieved)

iv. 5/16 Drive Suitable for SMA Connectors

19. Fairview Microwave SCA1814-0505-60 RG-402 Coax Cable with N-Type Connectors, or equivalent

a. RF Specs:

i. Frequency Range: 0-18 GHz (min)

ii. Cable Type: RG-402, or equivalent

iii. Length: 60” (nominal)

iv. Insertion Loss: 4 dB (0.8 dB/ft) at 18 GHz

v. Connectors: N-Type Male Connectors, Both Ends

20. Fairview Microwave SCA1814-0101-60 RG-402 Coax Cable with SMA Connectors, or equivalent

a. RF Specs:

i. Frequency Range: 0-18 GHz (min)

ii. Cable Type: RG-402, or equivalent

iii. Length: 60” (nominal)

iv. Insertion Loss: 4 dB (0.8 dB/ft) at 18 GHz

v. Connectors: SMA Male Connectors, Both Ends

Requirements for Mini-Circuits Components: 0003

1. Mini-Circuits ZVE-3W-183+ Medium-Power Amplifier, or equivalent

a. RF Specs:

i. Frequency Range: 6-18 GHz (min)

ii. Gain: 35 dB (nominal)

iii. Output Power: +31 dBm P1dB (min)

iv. Connectors: SMA or 3.5-mm Female Connectors

b. Electrical:

i. Power Supply: +15 V DC

ii. Current Draw: 2.2 Amps (max)

c. Mechanical:

i. With heat sink (7.5” wide x 2.0” length x 2.85” height (max))

ii. Dimensions: 7.5” wide x 2.0” length x 3.6” height (max), excluding connectors

2. Mini-Circuits ZVE-3W-183X+ Medium-Power Amplifier, or equivalent

a. RF Specs:

i. Frequency Range: 6-18 GHz (min)

ii. Gain: 35 dB (nominal)

iii. Output Power: +31 dBm P1dB (min)

iv. Connectors: SMA or 3.5-mm Female Connectors

b. Electrical:

i. Power Supply: +15 V DC

ii. Current Draw: 2.2 Amps (max)

c. Mechanical:

i. No heat sink attached

ii. Dimensions: 2.5” wide x 2.0” length x 0.8” height (max), excluding connectors

3. Mini-Circuits ZX60-183-S+ Wide-Band Amplifier, or equivalent

a. RF Specs:

i. Frequency Range: 6-18 GHz (min)

ii. Gain: 24 dB (nominal)

iii. Output Power: +18 dBm P1dB (nominal)

iv. Connectors: SMA or 3.5-mm Female Connectors

b. Electrical:

i. Power Supply: +5 V DC

ii. Current Draw: 300 mA (max)

c. Mechanical:

i. Dimensions: 0.8” wide x 0.8” length x 0.5” height (max), excluding connectors

4. Mini-Circuits ZHL-42 Medium-Power Amplifier, or equivalent

i. Frequency Range: 0.7-4.2 GHz (min)

ii. Gain: 30 dB (nominal)

iii. Output Power: +28 dBm P1dB (min)

iv. Connectors: SMA or 3.5-mm Female Connectors

b. Electrical:

i. Power Supply: +15 V DC

ii. Current Draw: 0.9 Amps (max)

c. Mechanical:

i. Dimensions: 3.25” wide x 7” length x 2.2” height (max), excluding connectors

5. Mini-Circuits ZRON-8GX+ Wide-Band Amplifier, or equivalent

a. RF Specs:

i. Frequency Range: 2-8 GHz (min)

ii. Gain: 20 dB (nominal)

iii. Output Power: +20 dBm P1dB (nominal)

iv. Connectors: SMA or 3.5-mm Female Connectors

b. Electrical:

i. Power Supply: +15 V DC

ii. Current Draw: 310 mA (max)

c. Mechanical:

i. Dimensions: 1.1” wide x 1.1” length x 0.5” height (max), excluding connectors

6. Mini-Circuits ZVA-183X-S+ Wide-Band Amplifier, or equivalent

a. RF Specs:

i. Frequency Range: 1-18 GHz (min)

ii. Gain: 26 dB (nominal)

iii. Output Power: +21 dBm P1dB (min)

iv. Connectors: SMA or 3.5-mm Female Connectors

b. Electrical:

i. Power Supply: +12 V DC

ii. Current Draw: 400 mA (max)

c. Mechanical:

i. Dimensions: 1.2” wide x 0.7” length x 0.5” height (max), excluding connectors

7. Mini-Circuits ZX05-153LH-S+ Wide-Band Frequency Mixer, or equivalent

a. RF Specs:

i. RF/LO Frequency Range: 3-15 GHz (min)

ii. IF Frequency Range: 0.1-4 GHz (min)

iii. LO Drive Power Level: +10 dBm (nominal)

iv. Conversion Loss: 6-7 dB (nominal)

v. LO/RF Isolation: 15 dB (min), 25 dB (nominal)

vi. Connectors: SMA or 3.5-mm Female Connectors

i. Dimensions: 0.9” wide x 0.8” length x 0.5” height (max), excluding connectors

8. Mini-Circuits VLM-63-2W+ 0-6 GHz Limiter, or equivalent

a. RF Specs:

i. Frequency Range: 3-6 GHz (min)

ii. Power-Limiting Threshold: +12 dBm (nominal)

iii. Maximum Power Leakage: +14 dBm (max)

iv. Insertion Loss: 1.0 dB (max)

v. Connectors: SMA or 3.5-mm Connectors (one male, one female)

b. Mechanical:

i. Coaxial insertion component, less than 1.5” in length

9. Mini-Circuits ZFSC-2-11+ Two-Way Power Divider, or equivalent

a. RF Specs:

i. Two-Way Power Divider

ii. Frequency Range: 10-2000 MHz (min)

iii. Insertion Loss: 2 dB (max)

iv. Isolation: 15 dB (nominal)

v. Connectors: 50-ohm BNC Female Connectors

10. Mini-Circuits ZAPD-21+ Two-Way Power Divider, or equivalent

a. RF Specs:

i. Two-Way Power Divider

ii. Frequency Range: 500-2000 MHz (min)

iii. Insertion Loss: 1 dB (max)

iv. Isolation: 18 dB (nominal)

v. Connectors: 50-ohm BNC Female Connectors

b. Mechanical:

i. Dimensions: 2” wide x 2” length x 0.8” height (max), excluding connector

11. Mini-Circuits ZB4PD1-2000+ Four-Way Power Divider, or equivalent

a. RF Specs:

i. Four-Way Power Divider

ii. Frequency Range: 800-2000 MHz (min)

iii. Insertion Loss: 1.2 dB (max)

iv. Isolation: 18 dB (nominal)

v. Connectors: 50-ohm BNC Female Connectors

i. Dimensions: 3.5” wide x 2.2” length x 0.9” height (max), excluding connector

12. Mini-Circuits HAT-1 50-Ohm BNC Attenuators, or equivalent

i. Frequency Range: 0-2000 MHz (min)

ii. Insertion Loss: Nominal Attenuation = 1 dB

iii. Connectors: 50-ohm BNC Connectors, One Male and One Female

b. Mechanical:

i. Coaxial Insertion Component, 2” in Length (max)

13. Mini-Circuits HAT-3 50-Ohm BNC Attenuators, or equivalent

a. RF Specs:

i. Frequency Range: 0-2000 MHz (min)

ii. Insertion Loss: Nominal Attenuation = 3 dB

iii. Connectors: 50-ohm BNC Connectors, One Male and One Female

b. Mechanical:

i. Coaxial Insertion Component, 2” in Length (max)

14. Mini-Circuits HAT-5 50-Ohm BNC Attenuators, or equivalent

a. RF Specs:

i. Frequency Range: 0-2000 MHz (min)

ii. Insertion Loss: Nominal Attenuation = 5 dB

iii. Connectors: 50-ohm BNC Connectors, One Male and One Female

b. Mechanical:

i. Coaxial Insertion Component, 2” in Length (max)

15. Mini-Circuits HAT-10 50-Ohm BNC Attenuators, or equivalent

a. RF Specs:

i. Frequency Range: 0-2000 MHz (min)

ii. Insertion Loss: Nominal Attenuation = 10 dB

iii. Connectors: 50-ohm BNC Connectors, One Male and One Female

b. Mechanical:

i. Coaxial Insertion Component, 2” in Length (max)

16. Mini-Circuits HAT-20 50-Ohm BNC Attenuators, or equivalent

a. RF Specs:

i. Frequency Range: 0-2000 MHz (min)

ii. Insertion Loss: Nominal Attenuation = 20 dB

iii. Connectors: 50-ohm BNC Connectors, One Male and One Female

i. Coaxial Insertion Component, 2” in Length (max)

17. Mini-Circuits HAT-30 50-Ohm BNC Attenuators, or equivalent

i. Frequency Range: 0-2000 MHz (min)

ii. Insertion Loss: Nominal Attenuation = 30 dB

iii. Connectors: 50-ohm BNC Connectors, One Male and One Female

b. Mechanical:

i. Coaxial Insertion Component, 2” in Length (max)

18. Mini-Circuits ANNE-50+ SMA Load, or equivalent

a. RF Specs:

i. Frequency Range: 0-18 GHz (min)

ii. 50-ohm Termination

iii. Connectors: SMA Male Connector

19. Mini-Circuits KARN-50-18+ N-Type Load, or equivalent

a. RF Specs:

i. Frequency Range: 0-18 GHz (min)

ii. 50-ohm Termination

iii. Connectors: N-Type Male Connector

20. Mini-Circuits BTRM-50+ BNC-Type Load, or equivalent

a. Quantity: 128

b. RF Specs:

i. Frequency Range: 0-2 GHz (min)

ii. 50-ohm Termination

iii. Connectors: BNC-Type Male Connector

Requirements for RF Lambda Components: 0004

1. RF Lambda RFLT2W2G18G SMA Two-Way RF Power Divider, or equivalent

a. RF Specs:

i. Two-Way Power Divider

ii. Frequency Range: 2-18 GHz (min)

iii. Insertion Loss: 1 dB (max)

iv. Isolation: 16 dB (min)

v. Connectors: SMA or 3.5-mm Female Connectors

b. Mechanical:

i. Dimensions: 1” wide x 1.9” length x 0.4” height (max), excluding connector

2. RF Lambda RFLT4W2G18G SMA Four-Way RF Power Divider, or equivalent

a. RF Specs:

i. Two-Way Power Divider

ii. Frequency Range: 2-18 GHz (min)

iii. Insertion Loss: 1.8 dB (max)

iv. Isolation: 16 dB (min)

v. Connectors: SMA or 3.5-mm Female Connectors

b. Mechanical:

i. Dimensions: 2.8” wide x 2.6” length x 0.4” height (max), excluding connectors

3. RF Lambda RFLT2W2G18GN N-Type Two-Way RF Power Divider, or equivalent

a. RF Specs:

i. Two-Way Power Divider

ii. Frequency Range: 2-18 GHz (min)

iii. Insertion Loss: 1.2 dB (max)

iv. Isolation: 16 dB (min)

v. Connectors: N-Type Female Connectors

4. RF Lambda RFDC2G18G30 30-dB Directional Coupler, or equivalent

a. RF Specs:

i. Directional Coupler

1. Coupling Factor: 30 dB (nominal)

2. Directivity: 10 dB (min)

ii. Frequency Range: 2-18 GHz (min)

iii. Insertion Loss: 1 dB (max)

iv. Isolation: 16 dB (min)

v. Connectors: SMA or 3.5-mm Female Connectors

5. RF Lambda RFLI101M24M40 UHF-Band Isolator, or equivalent

i. Frequency Range: 240-400 MHz (min)

ii. Insertion Loss: 1 dB (max)

iii. Isolation: 18 dB (min)

iv. Power Handling: 1 W (min), in either direction

v. Connectors: SMA or 3.5-mm Female Connectors

b. Mechanical:

i. Dimensions: 2.4” wide x 2.1” length x 1.1” height (max), excluding connectors

6. RF Lambda RFLT2W08025 SMA Two-Way IF Power Divider, or equivalent

a. RF Specs:

i. Two-Way Power Divider

ii. Frequency Range: 0.8-2.5 GHz (min)

iii. Insertion Loss: 0.5 dB (max)

iv. Isolation: 20 dB (min)

v. Connectors: SMA or 3.5-mm Female Connectors

b. Mechanical:

i. Dimensions: 1.2” wide x 1.4” length x 0.4” height (max), excluding connectors

7. RF Lambda RFLT4W08025 SMA Four-Way IF Power Divider, or equivalent

a. RF Specs:

i. Four-Way Power Divider

ii. Frequency Range: 0.8-2.5 GHz (min)

iii. Insertion Loss: 0.7 dB (max)

iv. Isolation: 20 dB (min)

v. Connectors: SMA or 3.5-mm Female Connectors

b. Mechanical:

i. Dimensions: 2.2” wide x 2.0” length x 0.4” height (max), excluding connectors

8. RF Lambda RFLT2W0002GS SMA Two-Way IF Power Divider, or equivalent

a. RF Specs:

i. Two-Way Power Divider

ii. Frequency Range: 20-2000 MHz (min)

iii. Insertion Loss: 0.8 dB (max)

iv. Isolation: 17 dB (min)

9. RF Lambda RFLT2W0002GN N-Type Two-Way IF Power Divider, or equivalent

i. Two-Way Power Divider

ii. Frequency Range: 20-2000 MHz (min)

iii. Insertion Loss: 1.2 dB (max)

iv. Isolation: 15 dB (min)

v. Connectors: N-Type Female Connectors

10. RF Lambda RFLT4W0502G SMA Four-Way IF Power Divider, or equivalent

a. RF Specs:

i. Four-Way Power Divider

ii. Frequency Range: 500-2000 MHz (min)

iii. Insertion Loss: 0.8 dB (max)

iv. Isolation: 20 dB (min)

Requirements for Pasternack Components: 0005

1. Pasternack PE8024 6-18 GHz Limiter, or equivalent

a. RF Specs:

i. Frequency Range: 13-15 GHz (min)

ii. Power-Limiting Threshold: +10 dBm (nominal)

iii. Maximum Power Leakage: +16 dBm (max)

iv. Insertion Loss: 2.5 dB (max)

v. Connectors: SMA or 3.5-mm Connectors (one male, one female)

b. Mechanical:

i. Coaxial insertion component, less than 1.5” in length

2. Pasternack PE8023 4-8 GHz Limiter, or equivalent

a. RF Specs:

i. Frequency Range: 5-7 GHz (min)

ii. Power-Limiting Threshold: +10 dBm (nominal)

iii. Maximum Power Leakage: +16 dBm (max)

iv. Insertion Loss: 1.5 dB (max)

v. Connectors: SMA or 3.5-mm Connectors (one male, one female)

b. Mechanical:

i. Coaxial insertion component, less than 1.5” in length

3. Pasternack PE7144 Single-Pole Double-Throw (SPDT) RF Relay Switch, or equivalent

a. RF Specs:

i. Frequency Range: 5-15 GHz (min)

ii. Insertion Loss: 0.5 dB (max)

iii. VSWR: 1.5:1 (max)

iv. Connectors: SMA or 3.5-mm Female Connectors

b. Control Specs:

i. Switching Control Voltage: 12 Volts DC

ii. Self-Cutoff Feature: control circuit to cut off DC current flow to the relay coil after the position switch (no continuous current flow through coil)

iii. Latching Feature: relay position latches in one position until explicitly switched to the opposite position

c. Mechanical:

i. Dimensions: 1.4” wide x 1.5” length x 0.6” height (max), excluding connectors

Requirements for Frequency Synthesizers: 0006

1. Phase Matrix FSL-0010 Frequency Synthesizer, or equivalent

a. RF Output:

i. Frequency Tuning Range: 1-3 GHz (min)

ii. Frequency Step Resolution: 1 kHz (max)

iii. Output Power: +10 dBm (min)

iv. Output Waveform: CW (no need for stepped sweep or modulation)

v. Connector: SMA or 3.5-mm Female Connector

b. Frequency Reference:

i. Internal Frequency Reference (no external reference provided)

ii. Frequency Stability: ±1 ppm

c. Control:

i. Can be controlled via USB or Ethernet interface

ii. Suitable Graphical User Interface (GUI) or Web Interface provided so that synthesizer can be controlled using a standard laptop computer (without end-user programming)

d. Electrical:

i. DC Power Supply: +12-V DC

ii. Power Draw: 25 Watts or 2 Amps (max)

e. Mechanical:

i. Dimensions: 4” wide x 4” length x 1” height (max), excluding connectors

Requirements for Manual Step Attenuators: 0007

1. Areoflex/Weinschel AF9003-69-11 Variable Step Attenuator, or equivalent

a. Frequency Range: 0-15 GHz, minimum

b. Attenuation:

i. Range: 0-69 dB

ii. Step Size: 1 dB increments

iii. Manual Control (for example, 10-dB knob & 1-dB knob)

c. Mechanical Configuration:

i. Concentric control knobs, if applicable (if there are separate 10-dB and 1-dB attenuation knobs, they must be concentric)

ii. Bulkhead-mount attenuator – suitable for installation on front panel of test equipment, such that control knobs and the body of the attenuator, with RF connectors, are on opposite sides of the panel to which the attenuator is mounted)

iii. Dimensions:

1. Length of attenuator body not to exceed 4” from panel-mounting plane, excluding connectors

2. Diameter of attenuator body not to exceed 1.75”, excluding connectors

d. RF Connectors:

i. SMA or 3.5-mm Female Connectors

ii. For Aeroflex/Weinschel AF9003-69, use “-11” option to provide:

1. Front (panel-side) connector: straight SMA female

2. Back (end of attenuator) connector: straight SMA female

Requirements for Internal RF Cables: 0008

High-Speed Interconnects - RF Coax Cable or equivalent (Ref Exhibit A Line Item #s 000801-000807)

a. Coax Cable Requirements:

i. 50-ohm Coax Cable

1. Suitable for mode-free operation up to 15 GHz

2. Low-loss cable, attenuation less than 40 dB per 100 feet at 15 GHz

ii. Nominal outer diameter approximately 0.2” (5 mm)

iii. Bend radius down to 2” (or less) supported without damaging cable

iv. Suitable for 90° bend within 4” from mating connector, including connector

b. Connectors:

i. Straight Male SMA connectors on each end

ii. Appropriate strain relief at connector

c. Lengths & Quantities:

000801: 6”, Quantity 34 000802: 12”, Quantity 24 000803: 18”, Quantity 20 000804: 48”, Quantity 20 000805: 72”, Quantity 16 000806: 96”, Quantity 6 000807: 240”, Quantity 16

Requirements for Internal L-Band Cables: 0009

L-Com L-Band Coax Cable or equivalent (Ref Exhibit A Line Item #s 00001-000914)

a. Coax Cable Requirements:

i. 50-ohm Coax Cable, Type RG-142

1. Suitable for operation up to 2 GHz

2. Attenuation less than 20 dB per 100 feet at 2 GHz

ii. Nominal outer diameter approximately 0.2” (5 mm)

iii. Bend radius down to 2” (or less) supported without damaging cable

iv. Suitable for 90° bend within 4” from mating connector, including connector

b. Connectors:

i. Straight Male BNC, N-Type, SMA or TNC connectors on each end

ii. Appropriate strain relief at connector

c. Connectors, Lengths & Quantities:

000901: BNC Male to BNC Male, 6”, Quantity 90 000902: BNC Male to BNC Male, 12”, Quantity 144 000903: BNC Male to BNC Male, 18”, Quantity 16 000904: BNC Male to BNC Male, 48”, Quantity 118 000905: BNC Male to BNC Male, 72”, Quantity 15 000906: BNC Male to BNC Male, 96”, Quantity 68 000907: BNC Male to BNC Male, 240”, Quantity 24 000908: SMA Male to SMA Male, 72”, Quantity 1 000909: SMA Male to BNC Male, 72”, Quantity 18 000910: SMA Male to BNC Male, 96”, Quantity 4 000911: N-Type Male to BNC Male, 72”, Quantity 24 000912: N-Type Male to BNC Male, 96”, Quantity 3 000913: N-Type Male to BNC Male, 144”, Quantity 6 000914: BNC Male to TNC Male, 300” (25’), Quantity 2

Requirements for Coax Cable Reels: 0010

1. Tacticom USA RG-435/U Cable Reel, or equivalent

a. Cable Reel Requirements:

i. Tubular Metal Reel

ii. Suitable for spooling 150’ of 0.3” diameter cable

iii. Access / notch for coaxial connection to interior end of cable without unspooling

iv. Compatible for use with Cable Reel Stand (below)

2. Tacticom USA RL-31-E Cable Reel Stand, or equivalent

a. Cable Reel Stand Requirements:

i. Metal Cable Reel Stand

ii. Portable, Foldable A-Frame

iii. Integrated Crank for spooling in cable

iv. Capable of supporting two Cable Reels (above)

v. Divided Axle – independent rotation of two installed Cable Reels

vi. Cable Reels can be removed from stand after spooling/unspooling

vii. Compatible for use with Cable Reels (above)

Requirements for RF Interface Cables: 0011

1. Florida RF Labs Armored & Weatherproofed Lab-Flex 290 Coax Cable, or equivalent

a. Coax Cable Requirements:

i. 50-ohm Coax Cable (Florida RF Labs Lab-Flex 290 or equivalent)

1. Suitable for mode-free operation up to 15 GHz

2. Low-loss cable, attenuation less than 20 dB per 100 feet at 15 GHz

ii. Armored & Weatherized cable for outdoor use / laying on unimproved surface

iii. 150’ Length

iv. Equivalent Florida RF Labs Part Number: NMSED-290AW-1800.0-NMSED

b. Connectors:

i. Straight Male N-Type Connectors on each end

ii. Appropriate weatherproofing at connector

iii. Appropriate strain relief at connector