F2027051 - Statement of Work.pdf
PDF 150 KB Posted
- Attached to
- Purchase of Smooth Drum Compactor
- Solicitation number
- F2027051
- Issued by
- Tarrant County, Texas
About this file
This Statement of Work details Tarrant County's Invitation for Bid (IFB No. F2027051) for the purchase of two smooth drum compactors to be used for rolling, compacting, and patching road pavements. One compactor is designated for Tarrant County Precinct 2 (delivery to 1203 E Kennedale Parkway, Kennedale, TX 76060), and one for Precinct 4 (delivery to 601 Longhorn Road, Suite 100, Fort Worth, TX 76179). The award will be made to the lowest responsible bidder whose equipment meets or exceeds all stated specifications. The statement of work does not specify response dates, due dates, site visits, bidders' meetings, award dates, or contract terms.
The pricing terms require that all delivery costs be included in the base equipment cost, with fully assembled equipment delivered ready for use. Bidders must be full-service dealers capable of providing all service and repairs. Standard warranty information is preferred at bid submission, and extended warranty is required: a minimum of 1,500 hours/3 years for Precinct 2 and 3,000 hours/5 years for Precinct 4. Equipment specifications differ between the two precincts, with Precinct 2 requiring a larger compactor (22,000–29,000 pounds, 66-inch drum width, 130 HP diesel engine) and Precinct 4 requiring a smaller unit (10,300 pounds maximum, 52-inch drum width, 50 HP minimum). All equipment must meet Federal and State of Texas safety, health, lighting, and noise regulations and EPA emission requirements (Tier 4 final for Precinct 2). The statement does not identify any set-asides, funding sources, or incumbent information.
View the file
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
IFB No. F2027051 Page 1
STATEMENT OF WORK
I. BACKGROUND
A. Tarrant County is requesting bids for a smooth drum compactor B. Tarrant County intends to award to the lowest responsible bidder who meets or exceeds specifications based on price of the equipment including standard warranty and delivery costs.
II. GENERAL REQUIREMENTS
A. Awarded vendor must provide equipment that meets or exceeds all Federal and State of Texas safety, health, lighting, and noise regulations. Offered equipment must meet this requirement at time of bid submission
B. Awarded vendor must provide equipment that meets or exceeds all Environmental Protection Agency (EPA) emission requirements. Offered equipment must meet this requirement at time of bid submission
C. Awarded vendor must not begin production of requested equipment before receiving a Tarrant County purchase order.
D. Bidders must be a full-service dealer capable of all service and repairs on offered equipment.
E. It is preferred that Bidders include standard warranty information with their bid submission. Tarrant County reserves the right to require that vendors provide this information before proceeding with award.
F. It is preferred that Bidders include extended warranty information with their bid submission. Tarrant County reserves the right to require bidders to provide this information before proceeding with award. For Line 1 (Precinct 2), extended warranty must be for 1,500 hours /3 Years at a minimum. For Line 2 (Precinct 4) extended warranty must be for 3,000 hours /5 Years at a minimum.
G. It is preferred that Bidders include a detailed specification sheet with their bid submission. Specification sheets must include references to all specifications included in this Statement of Work at a minimum. Tarrant County reserves the right to require that vendors provide this information before proceeding with award.
III. DELIVERY REQUIREMENTS
A. Awarded vendor must include all delivery costs in base cost of the equipment.
B. Awarded vendor must deliver equipment fully assembled and ready to use.
C. Awarded vendor must not delete any equipment that is included as standard by the equipment manufacturer from delivered equipment.
IFB No. F2027051 Page 2
D. Awarded vendor must provide an operator’s manual for offered equipment at time of delivery. Tarrant County will accept a digital operator’s manual.
E. Awarded vendor must not include decals or advertisements on delivered equipment. The exception to this requirement are manufacturer standard markings.
IV. EQUIPMENT REQUIREMENTS - PRECINCT 2
A. Awarded vendors must provide equipment that meets or exceeds the following specifications at a minimum.
B. General Requirements
1. Locking engine components
2. Equipment weight with Roll Over Protection System (ROPS): 22,000 pounds to 29,000 pounds
3. Ground clearance (from bottom of chassis to ground): 11 inches minimum
4. Drum width: 66 inches maximum
5. Drum diameter: 51 inches maximum
6. Drum offset for decreased roller marks: 2 inches minimum
7. Inside turning radius: 120 inches minimum
8. Equipped with asphalt temperature sensors
9. Vibratory Frequency range (HZ): 51hz – 67hz
10. Dual vibrating drums (front and rear)
11. Hydrostatic Drive (front and rear)
C. Engine Requirements
1. 4-cylinder diesel engine
2. Liquid cooled engine
3. Gross horsepower: 130 HP minimum
4. Tier 4 final
5. Fuel Tank Capacity: 10 hours of operation minimum
6. Hydrostatic drive: Two (2) speed minimum
7. Travel speed: 11 miles per hour minimum
8. Traction speed range: 0-7.5 mph
D. Electrical Requirements
1. System voltage: 12 (twelve) volt or 24 (twenty-four) volt
2. Alternator: 80 amps minimum
IFB No. F2027051 Page 3
3. Easy access jump start terminal E. Water System Requirements
1. Polyethylene tank
2. Pressurized water feed with filtration system
3. 12V automatic water control pressurized system with self-draining sprinkler tubes and nozzles for front and rear drums with sprinkler timer
F. Safety Requirements
1. Roll Over Protection System (ROPS) and Fall Object Protective
Structure (FOPS) with fixed metal canopy, or approved equivalent
2. Back-up alarm
3. Back-up camera installed at the time of equipment manufacturing
(post-manufacturing installation is not acceptable)
4. LED strobe light mounted on ROPS/FOPS for front and rear visibility installed at the time of equipment manufacturing (post-manufacturing installation is not acceptable)
5. Front and rear working lights
6. Parking/emergency brake: multidisc front and rear drums
7. Slip resistant operator area floorboards
G. Additional Requirements
1. Comfort suspension operator seat
2. Capability to operate equipment from both sides (right and left) of equipment
3. Steering system: center point articulation design
4. Adjustable seat so driver can visually see the outside edge of drum on both sides of machine. Seat will have dual arm rest.
5. Dash panel warning lights/alarms. Engine oil pressure/temperature and fuel indicator
6. Vandalism guard for dash panel
7. Drum scrapers: front and rear
8. Operation, parts and service manuals
V. EQUIPMENT REQUIREMENTS - PRECINCT 4
A. Awarded vendors must provide equipment that meets or exceeds the following specifications at a minimum.
B. General Requirements
IFB No. F2027051 Page 4
1. Locking engine components
2. Equipment weight: 10,300 pounds maximum
3. Equipment height (from top of beacon light to ground): 106 inches maximum
4. Ground clearance (from bottom of chassis to ground): 11 inches minimum
5. Drum width: 52 inches maximum
6. Inside turning radius: 120 inches minimum
C. Engine Requirements
1. Inline 4-cylinder turbo charged diesel engine
2. Liquid cooled engine
3. Horsepower: 50 minimum
4. Fuel Tank Capacity: 10 hours of operation minimum
5. Hydrostatic drive: Two (2) speed minimum
6. Travel speed: 11 miles per hour minimum
D. Electrical Requirements
1. System voltage: 12 (twelve) volt or 24 (twenty-four) volt
2. Alternator: 80 amps minimum
3. Easy access jump start terminal
E. Water System Requirements
1. Polyethylene tank
2. Pressurized water feed with filtration system
3. Front drum pressurized sprinkler system with self-draining sprinkler tubes and nozzles
4. Rear drum pressurized sprinkler system with self-draining sprinkler tubes and nozzles F. Safety Requirements
1. Roll Over Protection System (ROPS) with canopy
2. Backup camera installed at the time of equipment manufacturing
(post-manufacturing installation is not acceptable)
3. Strobe light installed at the time of equipment manufacturing (post-manufacturing installation is not acceptable)
4. Gauges with audible alarms
5. Slip resistant operator area floorboards
IFB No. F2027051 Page 5
G. Additional Requirements
1. Comfort suspension operator seat
2. Capability to operate equipment from both sides (right and left) of equipment
3. Drive levers installed on both sides (right and left) of equi
File details come from the government source that posted it. Updated .