Engineering_Instructions.docx

REV:

ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

XXXXXXXXXXXXXXXX

2. PART NUMBER:

3. NATIONAL STOCK NUMBER:

1234-12-123-1234FG

4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC, WILL BE USED IN LIEU OF THE DATA INDICATED. THE SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO INDICATED.

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

COMBINER ASSEMBLY (F-16)

2. PART NUMBER:

048228

3. NATIONAL STOCK NUMBER:

1270-99-179-7577WF

4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC., WILL BE USED IN LIEU OF THE DATA INDICATED. THE SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO INDICATED.

5. MARK PER MIL-STD-130.

6. THE SOURCES/MATERIALS IF LISTED ON THE SPECIFICATION, STANDARDS AND DRAWINGS ARE THE ONLY SOURCES/MATERIALS FOR THOSE ITEMS. ANY SUBSTITUTIONS SHALL HAVE PRIOR APPROVAL BY THE COGNIZANT ENGINEERING ACTIVITY.

7. IUID (ITEM UNIQUE IDENTIFIER) REQUIREMENTS AND EXPECTATIONS WHICH THE CONTRACTOR MUST ENSURE ARE COMPLIED WITH.

A. CONTRACTORS DRAWINGS SHALL BE CHANGED OR SUPPLEMENTED BY CONTRACTOR FOR IUID COMPLIANCE.

B.. LABEL SHALL CONTAIN ALL DATA ON EXISTING LABEL, (IF EXISTING LABEL IS TO BE REPLACED), ONLY DELETE EXISTING LABEL WITH GOVERNMENT ENGINEERING PERMISSION.

C. USE HRI (HUMAN READABLE) AND MACHINE READABLE MATRIX. (USAF NOT EQUIPED TO READ BARCODE).

D. IUID MATRIX NEEDS TO BE HIGHLY VISIBLE, IN A LOCATION EASILY ACCESSIBLE.

E. IUID MARKING MUST BE PERMANENT.

F. MIL-STD-130, ANSI/AIM BCII, ISO 15434, ISO 15415, AND ISO 15418

G. IUID MARKING SPECIFICATIONS.

1. MINIMUM 1/8 INCH LETTERING ON HUMAN READABLE TO INCLUDE:

A. CAGE (17V)

B. P/N (1P)

C. SERIAL NUMBER (IS)

2. MINIMUM 1/4 INCH SQUARE ON MACHINE READABLE 2D MATRIX -CONSTRUCT 2 - TO INCLUDE

A. CAGE (17V)

B. P/N (1P)

C. SERIAL NUMBER (IS)

IF DEVIATIONS FROM THESE INSTRUCTIONS ARE REQUIRED OR DESIRED, PERMISSION FROM GOVERNMENT ENGINEER IS REQUIRED.

8. THIS IS AN AIRCRAFT PART. USE THE APPROPRIATE PORTION OF MIL-STD-2000 THAT APPLIES TO AIRCRAFT SOLDERING FOR ALL SOLDERING REQUIREMENTS. *NOTE: J-STD-001 MAY BE USED IN LIEU OF MIL-STD-2000, IF SPECIFICATION MEETS OR EXCEEDS MIL-STD-2000.

9. EFFECTIVE 9 MAY 2005 THE DEPARTMENT OF THE AIR FORCE ISSUED AN AIR WORTHINESS ADVISORY (M-05-01) REGARDING THE USE OF LEAD-FREE SOLDER IN ELECTRICAL AND ELECTRONIC MILITARY PRODUCTS. TO DATE, NO LEAD-FREE SOLDER FORMULATION HAS MATCHED THE RELIABILITY AND PERFORMANCE QUALITIES OF THE STANDARD LEADED SOLDERS. THEREFORE, UNTIL SUCH TIME AS A SUITABLE, RELIABLE LEAD-FREE SOLDER REPLACEMENT IS IDENTIFIED, ALL ELECTRONIC EQUIPMENT SUPPLIERS SHALL CONTINUE TO PROVIDE THE DEPARTMENT OF THE AIR FORCE WITH ITEMS WHICH MEET ALL PERFORMANCE, COMPATIBILITY, AND RELIABILITY STANDARDS PREVIOUSLY ESTABLISHED WITH LEADED SOLDERS. FAILURE TO DO SO, COULD ADVERSELY IMPACT THE PERFORMANCE AND RELIABILITY OF WEAPON SYSTEMS AFFECTING NATIONAL SECURITY.

PREPARED BY:

RICHARD TILTON

OFFICE SYMBOL:

GBMAF

DATE:

20080411

PREPARED BY:

JED FOY

OFFICE SYMBOL:

416 SCMS/GUEAA

DATE:

DEC. 6, 2021

HILL AFB FORM 462 Page 1 of 2