FSCS Wire Diagrams.ppt

Com1: Limnoscale Com2: Touch Screen Com3: Large Scale Com4: Flow Scale Com5: Sling Scale Com6: Bar Code Reader Com7: Small Scale Com8: Scantrol Fish Board Com9: Calipers Com10: Label Printer 1200, o, 7,1 none 9600,n,8,1 xon/xoff 9600nn,8,1 none 1200,n,8,1 xon/xoff 9600n,,8,1 none 9600,n,8,1 hardware 9600,n,8,1 none 9600,n,8,1 none 4800,e,7,2 none 9600,n,8,1 none NOAA ship Henry B. Bigelow FSCS station port listing Not all devices are connected at every station April, 2007. ST Wood N:\Survey\System_Diagrams\FSCS_Wire_Diagrams.ppt

USB

Speaker to ‘audio in’

COM 2:

Video Output 1 Video Pass through Keyboard and Mouse Keyboard, Mouse and Video output from switch Two CAT6 wires between micro extender boxes;

(Computer room to Wet Lab) for each FSCS work station CAT6 wire KVM Micro Extender FSCS programming station.

on port side of acoustic lab.

Switches among FSCS computers.

Each FSCS workstation is plugged Into the FSCS video switch.

From this switch each may be connected With the FSCS programming station in the acoustic lab at the same time that it is connected through the USB micro Extender to the touchscreen In the wet lab.

Acoustic Lab 1-38-2 Wet (fish) Lab 1-58-1 Video to touchscreen monitor at FSCS workbench Serial COM 2:

to touchscreen touch feature Speaker Speaker Overhead ‘J’ Box 2 monitors, 1 serial port 1 speaker, and 4 USB ports are available from each computer through this micro extender KVM Micro Extender NOAA Ship Henry B. Bigelow Fish Scientific Computing System (FSCS) May 1st, 2007

Block diagram of each workstation’s Video, keyboard, USB, Speaker and Com2 configuration.

Com 1, and Com 3 through 10 are extended to the ‘J’ boxes in the wet lab through the wago punch blocks.

FSCS Video Switch N:\Survey\System_Diagrams\FSCS_Wire_Diagrams.ppt COMS 1: and 3: through 10:

Wago Block Cable between Wago terminal blocks USB for outboard Touch screen

FSCS computer

USB Micro Extender

USB Micro Extender

Data to PC Data from PC Signal Ground Com port In FSCS ---computer 3 pin Fishboard Scale SL2 SmallScale 5 pin 3 pin 5 pin Bar-Code Reader + 5 Volts Scantrol Fish Board Large SL1 Small Scales SL2- 4 + 12 Volts 4 pin + 12 Volts Limnoscale 5 pin Label Printer Gnd Hardware interrupt +20 volts Printer PS In ‘J’ box Flow Scale, Station 1 Sling Scale, Station 1 Printer hardware interrupt:

Pins 6&8 on printer wired to pins 6&8 on computer (green, blue) WAGO Block in FSCS ‘J’ Box; NOAA ship Henry Bigelow, March, 2007 4 pin Caliper Lumberg connector on side of ‘J’ box Caliper Hardware interrupt:

4&7 on caliper db9 to pins 4&7 on computer (orange, blue)

Forward

5 pin male Pin 2 Pin 3 Pin 5 Data from printer Data to printer Ground Pins 6&8 Interrupt from printer

+12 volts from printer PS

Printer power connector

DB 9 M

To printer Zebra TLP 2844 receipt printer cable

Fowler Ultra-Cal IV caliper adapter cable

DB 9 M

To caliper cable 4 pin male Cartridges Pin 2 Pin 3 Pin 5 Pins 7 & 4

Small Scale data cable to FSCS diagram

Inside of Scale Display

GND

3 Pin Male

TX

RX

COM1

RX

GND

TX