E70-0001 Shipping Container Requirement 221103.pdf

Shipping Container – Qty 2

Container type ISO CONTAINER WITH ONE FULL SIDE OPENING (DOUBLE BIFOLD SWING DOOR)

AND DOUBLE DOORS ON ONE END

Material 14 GAUGE STEEL External Dimension (LxWxH) 20’ x 8' x 9.5’ Minimum Internal dimension with Insulation (LxWxH): 229.69" x 90.25" x 102.52"

Minimum side door dimension (WxH): 229.69" x 100"

Minimum end door dimension (WxH): 89.57" x 97"

Flooring

THE CONTAINER FLOOR SHALL BE SKINNED WITH 0.5" FLAT STEEL PLATING (ASTM

A588 GRADE A) AND MUST BE WELDED/BOLTED TO THE BASE FRAME OF THE

CONTAINER. THE TOP OF THE FLOOR AND BOTTOM OF THE DOOR FRAMES SHALL

BE FLUSH WITHIN 0.13 INCHES

Insulation

A. CEILING AND WALL CONSTRUCTION OF THE CONTAINER SHALL INCLUDE AN

INSULATON BARRIER INSULATING FROM THE OUTER WALL TO 0.5" BEYOND

INNER WALL SURFACE.

B. INSULATION MATERIAL SHALL BE SUITABLE FOR USE IN MARINE ENVIRONMENT

AND SHALL BE FABRICATED FROM

MATERIAL THAT DO NOT GIVE OFF TOXIC FUMES OR SUPPORT COMBUSTION.

C. MINIMUM R FACTOR OF R-4.

D. INSULATION SHOULD INCLUDE 0.06" 5052 ALUMINUM RIGID INTERIOR

BARRIER.

E. IT IS NOT REQUIRED TO INSULATE INNER SURFACES OF PORTAL (DOOR

PERIMETER) AND INSULATION SHOULD BE

TERMINATED AT EDGES, AROUND FITTINGS AND FIXTURES.

Finish/Paint

INTERIOR STRUCTURE FINISH DETAILS: UNLESS OTHERWISE SPECIFIED, FOLLOW

ALL COATINGS MANUFACTURER'S COATING APPLICATION INSTRUCTIONS.

>SURFACE PREPARATION: ABRASIVE BLAST TO SSPC-SP10 (NEAR WHITE METAL).

>PRIMER COAT: ONE COAT OF MIL-PRF-23236D, TYPE V, CLASS 7, GRADE C. APPLY

PRIMER COAT TO BARE SURFACES ONLY IAW MANUFACTURER INSTRUCTIONS.

>STRIPE COAT: ONE COAT OF MIL-PRF -23236D, TYPE V, CLASS 7, GRADE C. APPLY

ON OUTSIDE CORNERS, EDGES, CREVICES, WELDS, AND OTHER IRREGULAR

SURFACES IAW MANUFACTURER INSTRUCTIONS.

>TOP COAT: ONE COAT OF MIL-PRF-24635F, TYPE V, CLASS 2, GRADE B,

COMPOSITION 2, COLOR WHITE (FED. STD. 595, COLOR CHIP NO. 27886.) APPLY

TO SURFACES PREPARED WITH PRIMER COAT IAW MANUFACTURER

INSTRUCTION.

EXTERIOR STRUCTURE FINISH DETAILS: UNLESS OTHERWISE SPECIFIED, FOLLOW

ALL COATINGS MANUFACTURER'S COATING APPLICATION INSTRUCTIONS.

>SURFACE PREPARATION: ABRASIVE BLAST TO SSPC-SP10 (NEAR WHITE METAL).

>PRIMER COAT: APPLY MIL-PRF-23236D, TYPE V, CLASS 7, GRADE C, IAW

MANUFACTURER INSTRUCTIONS. APPLY PRIMER AS NECESSARY TO ATTAIN A

TOTAL PRIMER DRY FILM THICKNESS (DFT) OF 12-16 MILS.

>TOP COAT: APPLY MIL-PRF-24635F, TYPE V, CLASS 2, GRADE B, COMPOSITION 2,

COLOR HAZE GRAY (FED. STD. 595, COLOR CHIP NO. 26270), IAW MANUFACTURER

INSTRUCTIONS. APPLY TOP COAT AS NECESSARY TO ATTAIN A TOTAL EXTERIOR

FINISH DFT OF 16-23 MILS.

Forklift Pockets SHALL BE IAW ISO 1496:1998.

Corner Fittings SHALL BE IAW ISO 1161:1984.

Shipping Container – Qty 2

Access Control

A. ALL LOCKING HARDWARE SHALL BE WITHIN EXTERIOR DIMENSION

BOUNDARIES SET FORTH BY ISO 1496:1998.

B. LOCKING HARDWARE REQUIREMENTS CAN BE MET BY USE OF A HIGH SECURITY

LOCK CONFIRMING TO MILITARY SPECIFICATION MIL-P-43607 (LATEST SERIES), OR

AS OTHERWISE LISTED IN APPENDIX D OF OPNAVINST 5530.13C.

C. THE LOCKS SHALL NOT REDUCE THE EFFECTIVE OPEN DOOR CLEARANCE FOR

LOADING/UNLOADING OPERATIONS.

D. CONTAINERS SHALL INCLUDE ANTI-TAMPERING MEASURES TO EFFECTIVELY

PROTECT CRITICAL TECHNOLOGIES

Door gaskets ALL CONTAINER OPENINGS SHALL BE SEALED WITH A CONTINUOUS GASKET IAW

ISO 1496:1998.

Transportation Certifications

CONTAINERS SHALL MEET TRANSPORTATION CERTIFICATIONS FOR ROAD, RAIL,

AND SEA IAW:

A. AMERICAN BUREAU OF SHIPPING (ABS) RULES FOR CERTIFICATION OF CARGO

CONTAINERS

B. INTERNATIONAL CONVENTION FOR SAFE CONTAINERS (CSC)