DWG.PKG.01.R400-3A10C3.Part.Number.2200693-A (1).pdf

CAGE CODE 0WY55 DWG NO. 2200693 SHEET 1 OF 4

SIZE CAGE CODE DWG NO. REV

A 0WY55 2200693 A

SCALE: NONE SHEET 1 OF 4

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

1313 HALLEY CIRCLE

NORMAN, OKLAHOMA 73069-8480

MILLIMETERS

1 PL

2 PL

ANGLES 2

INCHES

2 PL .02

3 PL .010

NOMENCLATURE

CAPACITOR, FIXED, PAPER DIELECTRIC, SCR COMM

APPROVALS

DWN CLS 240213 RMT DTH 240213

CHK JLM 240213 DOC MDW 240213

ENGR KAM 240213 CM

QA ROC

VENDOR ITEM CONTROL DRAWING

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

1D20990 WSR-88D

A 240213

ECP 0912

ECO A10359

INITIAL RELEASE KAM

CAGE CODE 0WY55 DWG NO. 2200693 SHEET 2 OF 4

SCALE: NONE SHEET 2 OF 4

GENERAL NOTES:

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

SPECIFICATION IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR FUTURE AVAILABILITY

AS A SOURCE OF SUPPLY FOR THE ITEM(S).

1.2. THE USE OF A DIFFERENT PART FROM A LISTED SUGGESTED SOURCE OF SUPPLY OR A PART FROM A

NON-LISTED SUGGESTED SOURCE OF SUPPLY WHICH MEETS THE SPECIFICATIONS HEREIN SHALL OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR- 88D RADAR OPERATIONS CENTER (ROC) AS WELL AS ACCEPTANCE INSPECTION BY THE NATIONAL

RECONDITIONING CENTER (NRC).

2. REQUIREMENTS:

2.1. CONSTRUCTION

2.1.1. THE CAPACITOR SHALL BE OF POLYPROPYLENE / PAPER DIELECTRIC, EXTENDED FOIL

CONSTRUCTION. THE CAPACITOR SHALL BE IMPREGNATED WITH A NON-TOXIC BIODEGRADABLE

MATERIAL.

2.1.2. CAPACITOR CASE: ELECTRO-TIN PLATED, STEEL CASE, HERMETICALLY SEALED.

2.1.3. MOUNTING HARDWARE: THE SUPPLIER SHALL PROVIDE PROPER FLAT WASHER, LOCK WASHER, AND

NUT ON EACH STUD.

2.2. ELECTRICAL

2.2.1. CAPACITANCE: 50 μF ± 10.0 PCT

2.2.2. VOLTAGE: 600 V PEAK

2.2.3. CURRENT: 60 AMP RMS MAX (50 uSEC PULSE WIDTH)

2.3. MECHANICAL

2.3.1. OUTLINE AND DIMENSIONS:

2.3.1.1. CAPACITOR (-201): PER FIGURE 1

2.4. ENVIRONMENTAL:

2.4.1. INDOOR:

2.4.1.1. OPERATING TEMPERATURE: -40°C (-40°F) TO +75°C (167°F).

2.4.1.2. NON-OPERATING TEMPERATURE: -55°C (-67°F) TO +90°C (194°F).

2.4.1.3. OPERATING HUMIDITY: 20 TO 80%.

2.4.1.4. NON-OPERATING HUMIDITY: 15 TO 95%.

2.4.2. ALTITUDE: UP TO 3300 METERS (10,826 FEET) ABOVE MEAN SEA LEVEL.

2.5. PART IDENTIFICATION:

CAGE CODE 0WY55 DWG NO. 2200693 SHEET 3 OF 4

SCALE: NONE SHEET 3 OF 4

2.5.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR. PART NUMBER

MAY BE APPLIED TO PACKAGING.

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

4. THE PART NUMBER IS THE DRAWING NUMBER SUFFIXED WITH THE APPLICABLE DASH NUMBER

SHOWN IN TABLE II.

5. SUGGESTED SOURCE(S) OF SUPPLY (MANUFACTURER(S)):

CORNELL DUBILIER ELECTRONICS (CDE) (CAGE CODE 2D829)

NEW BEDFORD, MA

PART NO.: PER TABLE II

GE GRID SOLUTIONS, LLC (GE) (CAGE CODE 7FD21)

ATLANTA, GA

PART NO.: PER TABLE II

TABLE II

DASH

NO.

ITEM MFR. PART NO. (CO.)

NOTE

NO.

-201 CAPACITOR, FIXED, PAPER DIELECTRIC, SCR COMM

SCRN232R-F (CDE)

A97F8676SC (GE)

SEE NOTE 1

NOTES:

1. THE -201 CONFIGURATION IS USED FOR PROCUREMENT.

CAGE CODE 0WY55 DWG NO. 2200693 SHEET 4 OF 4

SCALE: NONE SHEET 4 OF 4

6. FIGURES AND DIAGRAMS

FIGURE 1