DWDT-1000600C-1170LAN-VER-1.pdf

1170LAN

A A

B B

C C

D D

E E

F F

G G

H H

+.004/-.002

+.005/-.002

+.006/-.002

+.008/-.002

+.010/-.002

+.012/-.002

.0135- .125

.126- .250

.251- .500

.501- .750

.751-1.000

1.001-2.000

HOLE SIZE

NOT TO BE USED FOR MANUFACTURE

UNLESS APPROVED FOR THE

UNITED STATES POSTAL SERVICE

SIGNATURE DATE

FOR THE

UNITED STATES POSTAL SERVICE DO NOT SCALE DRAWING SHEET

REMOVE ALL BURRS & SHARP EDGES

COMPUTER AIDED DESIGN SYSTEM DRAWING

DO NOT REVISE MANUALLY

SCALE:

DRAWN BY

CHECKED BY

APPROVED BY

PROJECT ENGR

CAGE NO.

UNLESS OTHERWISE SPECIFIED:

ALL DIMENSIONS ARE IN INCHES

DECIMALS--.XX----`

DECIMALS--.XXX--`

FRACTIONS---------`

ANGLES--------------`

T O L E R A N C E

TOLERANCE

MAIL COLLECTION BOX,

1170LAN

1 of 1 1 / 4

27085

11/15/2017

11/27/2017

11/27/2017

11/27/2017

J. DEWNANDAN

M. SPEARS

J. SHENHAR

J. DEWNANDAN

W. TARTAL

11/27/2017

.04

.020

Copyright © 2017 United States Postal Service.

All rights reserved.

APPLICATION

DASH NEXT ASSY USED ONDASH NEXT ASSY USED ON

APPLICATION

SIZE:

E

DWG NO.

DT-1000600C

NOTES:

1. THIS DRAWING PREPARED IN ACCORDANCE WITH THE

STANDARDS LISTED IN ASME Y14.100-2013, SECTION 2.

2. THE FINISH OF THE 1170LA COLLECTION MAIL BOX

SHALL CONSIST OF THE FOLLOWING:

TOP COAT APPLICATION (FINAL):

AFTER THE UNIT HAS BEEN FULLY ASSEMBLED

AND CAULKED, A FINAL EXTERIOR APPLICATION OF

THE ANTI-GRAFFITI POWDER COAT SHALL BE APPLIED

IN ACCORDANCE WITH USPS-P-1170, TYPE II

POLYESTER-BASED COATING, BLUE, COLOR CHIP

NO. 15050 IN ACCORDANCE WITH FED-STD-595.

3. BEFORE THE FINAL FINISH PROCESS, APPLY SEALANT,

ITEM 55, TO ALL SEAMS. DO NOT USE SEALANT AROUND

SIDES AND REAR OF BOTTOM WHEN INSTALLING MAIN

DOOR ASSY, ITEM 6.

4. INSTALL INSTRUCTIONAL LABEL, ITEM 7, AT THE APPROXIMATE

POSITION SHOWN AFTER APPLYING FINAL FINISH.

5. BRAND NAME OR EQUAL, INTERCHANGEABILITY REQUIRED

FOR ALL COMMERCIAL ITEMS.

6. MATERIAL: (ITEM 2) IRON, DUCTILE, FOR CASTING, IN

ACCORDANCE WITH ASTM A536-84 GRADE 65-45-12.

7. UNLESS OTHERWISE SPECIFIED:

SURFACE ROUGHNES SHALL BE AS CAST.

ALL FILLETS RADII SHALL MANUFACTURER'S MINIMUM.

CORNER RADII SHALL BE MANUFACTURER'S MINIMUM.

8. PRE-FINISH: E-COAT ALL SURFACES IN ACCORDANCE WITH

DOCUMENT USPS2000923.

9. MATERIAL: (ITEM 3) STAINLESS STEEL BAR, ROUND, CONDITION A,

COLD FINISHED, .375 DIA STK IN ACCORDANCE WITH

ASTM A276-17, TYPE 304.

10. MATERIAL: STAINLESS STEEL SHEET, NO. 2B FINISH,

COLD ROLLED, ANNEALED AND PICKLED, .0751 (14 GA) STK

IN ACCORDANCE WITH ASTM A240-18, TYPE 304.

11. MATERIAL: (ITEM 21) GREY DUCTILE IRON, GRADE 65-45-12,

BHN RANGE 156-217 IN ACCORDANCE WITH ASTM A536.

12. MATERIAL: (ITEM 62) STAINLESS STEEL SHEET, NO. 2B FINISH,

COLD ROLLED, ANNEALED AND PICKLED, .0751 THK (14 GA)

IN ACCORDANCE WITH ASTM A 240. TYPE 316.

13. MATERIAL: (ITEMS 25, 26) STEEL SHEET, COLD ROLLED,

COMMERCIAL QUALITY, EXPOSED, TEMPER ROLLED,

MATTE FINISH, .0598 (16 GA) STK IN ACCORDANCE WITH

ASTM A1008/1008M-16 CS TYPE B.

PRE-FINISH: E-COAT ALL SURFACES IN ACCORDANCE WITH

DOCUMENT USPS2000923.

14. MATERIAL: (ITEMS 27, 28) STEEL SHEET, COLD ROLLED,

COMMERCIAL QUALITY, CS TYPE B, EXPOSED, TEMPER ROLLED,

MATTE FINISH, .0598 (16 GA) STK IN ACCORDANCE WITH ASTM

A1008/A1008M-16.

EMBOSS AT A DEPTH OF .045-.065 INCHES, IN POSITION SHOWN,

"USPS" IN 1.00 INCH HIGH, UPPER CASE, ARIEL STYLE

CHARACTERS, IN ACCORDANCE WITH SAE AS478 METHOD 1C.

EMBOSS AT A DEPTH OF .045-.065 INCHES, IN POSITION SHOWN.

THE MONTH / YEAR OF MANUFACTURE AND MANUFACTURER'S

NAME / STATE IN .75 INCH HIGH, UPPER CASE, ARIEL

STYLE CHARACTERS, IN ACCORDANCE WITH SAE AS478

METHOD 1C.

PRE-FINISH: E-COAT ALL SURFACES IN ACCORDANCE WITH

DOCUMENT USPS2000923.

15. MATERIAL: (ITEM 29) STEEL SHEET, COLD ROLLED, COMMERCIAL

QUALITY, CS TYPE B, EXPOSED, TEMPER ROLLED,

MATTE FINISH, .1046 (12 GA) STK IN ACCORDANCE

WITH ASTM A1008-16.

PRE-FINISH: E-COAT ALL SURFACES IN ACCORDANCE WITH

DOCUMENT USPS2000923.

FINAL FINISH: APPLY FINAL FINISH ONLY TO THE INSIDE OF

PART, IN ACCORDANCE WITH SPECIFICATION USPS-P-1170,

TYPE II POLYESTER-BASED COATING, BLUE, COLOR CHIP

NO. 15050 IN ACCORDANCE WITH FED-STD-595. UNLESS

OTHERWISE SPECIFIED, ALL DIMENSIONS ARE

APPLICABLE AFTER FINAL FINISH.

"INSIDE" REFERS TO ALL SURFACES HIDDEN AFTER

INSTALLATION AT THE TOP ASSEMBLY, AND WOULD NOT

BE EXPOSED TO A FINAL PAINT FINISH.

16. MATERIAL: (ITEMS 22, 31) STAINLESS STEEL SHEET, NO. 2B

FINISH, COLD ROLLED, ANNEALED AND PICKLED,

.1200 THK (11 GA) IN ACCORDANCE WITH ASTM A 240. TYPE 316.

MATERIAL: (ITEM 31) STAINLESS STEEL SHEET, NO. 2B FINISH,

COLD ROLLED, ANNEALED AND PICKLED, .1054 THK (12 GA)

IN ACCORDANCE WITH ASTM A 240. TYPE 316.

MATERIAL: (ITEM 31) STAINLESS STEEL BAR, ROUND, ANNEALED

AND COLD FINISHED, .3125 DIA IN ACCORDANCE WITH

ASTM A276. TYPE 316.

MATERIAL: (ITEM 31) STAINLESS STEEL BAR, ROUND, ANNEALED

AND COLD FINISHED, .625 DIA IN ACCORDANCE WITH

ASTM A276. TYPE 316.

17. MATERIAL: (ITEM 5) STEEL SHEET, COLD ROLLED, COMMERCIAL

QUALITY, EXPOSED, TEMPER ROLLED, MATTE FINISH,

.0598 (16 GA) STK IN ACCORDANCE WITH

ASTM A1008-16 CS TYPE B.

PRE-FINISH: E-COAT ALL SURFACES IN ACCORDANCE WITH

DOCUMENT USPS2000923.

FINAL FINISH: APPLY FINAL FINISH ONLY TO THE ENTIRE

PART, IN ACCORDANCE WITH SPECIFICATION USPS-P-1170,

TYPE II POLYESTER-BASED COATING, BLUE, COLOR CHIP

NO. 15050 IN ACCORDANCE WITH FED-STD-595. UNLESS

OTHERWISE SPECIFIED, ALL DIMENSIONS ARE

APPLICABLE AFTER FINAL FINISH.

DO NOT APPLY FINISH TO THREADS OF ITEM 2.

18. MATERIAL: (ITEM 6) STEEL STRIP, HOT ROLLED, COMMERCIAL

QUALITY, PICKLED, OILED, SLIT EDGE, .1793 (7 GA) STK

IN ACCORDANCE WITH ASTM A1011/A1011M-15

CS TYPE B.

19. MATERIAL: STEEL SHEET, HOT ROLLED, PICKLED AND

OILED, .0747 (14 GA) STK IN ACCORDANCE WITH

ASTM A1011/A1011M-15, CS TYPE B.

20. MATERIAL: STAINLESS STEEL BAR, ROUND, CONDITION A,

COLD FINISHED, .312 DIA STK IN ACCORDANCE WITH

ASTM A276-17, TYPE 304.

FINISH: PASSIVATE IN ACCORDANCE WITH ASTM A967-13.

21. MATERIAL: STEEL SHEET, COLD ROLLED, COMMERCIAL

STEEL, EXPOSED, TEMPER ROLLED, MATTE FINISH,

.1196 (11 GA) STK IN ACCORDANCE WITH ASTM A1008

CS TYPE B.

MATERIAL: STEEL SHEET, COLD ROLLED, COMMERCIAL

STEEL, EXPOSED, TEMPER ROLLED, MATTE FINISH,

.0598 (16 GA) STK IN ACCORDANCE WITH

ASTM A1008-16 CS TYPE B.

SPOT WELDING SHALL BE IN ACCORDANCE WITH

AWS C1.1:2012.

PRE-FINISH: E-COAT ALL SURFACES IN ACCORDANCE WITH

DOCUMENT USPS2000923.

FINAL FINISH: APPLY FINAL FINISH TO THE ENTIRE PART, IN

ACCORDANCE WITH SPECIFICATION USPS-P-1170,

TYPE II POLYESTER-BASED COATING, BLUE, COLOR CHIP

NO. 15050 IN ACCORDANCE WITH FED-STD-595.

UNLESS OTHERWISE SPECIFIED, ALL DIMENSIONS ARE

APPLICABLE AFTER FINAL FINISH.

REVISIONS

LTR DESCRIPTION DATE APPROVAL

THE INFORMATION CONTAINED ON THIS DOCUMENT IS THE

CONFIDENTIAL PROPERTY OF THE UNITED STATES POSTAL

SERVICE AND SHALL NOT BE COPIED OR REPRODUCED IN

ANY MANNER OR DISCLOSED TO THIRD PARTIES WITHOUT

THE EXPRESS, WRITTEN PERMISSION OF THE UNITED STATES

POSTAL SERVICE AND SHALL NOT BE USED FOR ANY

PURPOSE WHATSOEVER, INCLUDING THE MANUFACTURER OF

THE PRODUCT DISCLOSED, FOR ANYONE OTHER THAN THE

UNITED STATES POSTAL SERVICE.

C NEW DESIGN

15.64

20.03

49.51

REFERENCE DRAWING:

USPS-P-1170 DRY POWDER COATINGS.

21.53