DRAWING REVISION C (6 PAGES).pdf

BRANCH HD

ENGINEER

CHECKED

PREPARED

CODE/SHOP

B

SIZE REV

DATE

PHONE

CONCURRENCE

CONCURRENCE

PROCESS IMPROVEMENT OFFICE

SHOP 64/99

FACILITY / SERVICE REQUEST #:

DEPARTMENT OF THE NAVY PUGET SOUND NAVAL SHIPYARD

BREMERTON, WASHINGTON

REVISION

REV SHT DESCRIPTION BY

SHEET 1 OF 6

PI-99-05182022 CCONCURRENCE

CONCURRENCE

S/99 360-476-0318 NO DEVIATIONS SHALL BE MADE WITHOUT AUTHORIZATION UNLESS NOTED

OTHERWISE.

REFERENCE

THIS DRAWING DOES NOT REQUIRE A DISTRIBUTION STATEMENT. IN

ACCORDANCE WITH DOD5200.1-R THIS DOCUMENT IS UNCLASSFIED AND

DOES NOT WARRANT AN FOUO STATEMENT IAW DOD 5200.1-R AP3.2.1. THIS

DRAWING DOES NOT CONTAIN CRITICAL TECHNOLOGY AS DEFINED BY

NAVSEA 5230.12.

CAGE CODE DRAWING No.

82522

DATE APPROVED

DISTRIBUTION STATEMENT D: Distribution authorized to DOD and U.S.

DOD contractors only. Administrative/operational use. Other requests for this document shall be referred to COMNAVSEASYSCOM (SEA OOD)

/S/ K. VARNER 05/18/2022

/S/ J. BRAATEN 05/18/2022 WATER FILTER

BRACKET

A ALL

REVISED PC#2 DIMENSIONS AND

MOVED THE ADJUSTMENT SLOTS

TO ACCOMMODATE CURRENT

HARDWARE.

VARNER 05/20/2022 VARNER

B ALL

ADDED RECESS TO FILTER RINGS.

ADDED RETENTION CLIPS.

ADJUSTED HARDWARE LENGTH.

INCREASED MTRL THICKNESS OF

BACK SUPPORT.

VARNER 07/26/2022 BRAATEN

B ALL

CHANGED THE I.D. OF PC# 2 TO

" TO SUPPORT FILTER CHANGES

VARNER 05/03/2023 LEISCHNER

REV.

SHEET 2 OF 6

SIZE DRAWING NO.

PI-99-05182022B C

GENERAL NOTES

1. PURPOSE

1.1. THIS DRAWING WAS PRODUCED TO SUPPORT THE

MANUFACTURE OF A WATER FILTER BRACKET.

2. GENERAL

2.1. DIMENSIONAL TOLERANCES SHALL BE THE FOLLOWING UNLESS

OTHERWISE SPECIFIED:

2.1.1. 1/16” UP TO 12” INCLUSIVE

2.1.2. 1/8” OVER 12” UP TO 72” INCLUSIVE

2.1.3. ¼” OVER 72”

2.1.4. ¼ DEGREE ANGULAR

2.1.5. 1/32” FOR HOLES

2.2. WHERE MIL-SPECS, STANDARDS, PROCESS INSTRUCTIONS,

DRAWINGS ARE NOTED ON THIS DRAWING, THE LATEST REVISION

SHALL BE IN EFFECT UNLESS ADHERENCE TO A DEFINITE REVISION

IS NECESSARY AND SPECIFIED.

2.3. COPIES OF THIS DRAWING ARE AVAILABLE IN PDF FORMAT FROM

S/99, S/64 PROCESS IMPROVEMENT DRAWING OFFICE.

3. SAFETY

3.1. BREAK ALL EXPOSED SHARP EDGES AND CORNERS WITH A

MINIMUM OF A 1/16” ROUND/CHAMFER

3.2. ALL BURRS AND OTHER POTENTIALLY HARMFUL LEFTOVERS

FROM MANUFACTURING/MODIFYING SHALL BE REMOVED TO

PREVENT INJURY.

4. WELDING AND NDT REQUIREMENTS

4.1. UNLESS OTHERWISE STATED ALL STRUCTURAL JOINTS SHALL BE

WELDED TO A MINIMUM SIZE OF 3/16” FILLET/BEVEL WELD.

4.2. MANUFACTURED BY PSNS: ALL WELDING OF ALUMINUM SHALL

BE IN ACCORDANCE WITH (IAW) PSNS WELD PROCEEDURE WP-

FAC REV A. NON-DESTRUCTIVE TESTING (NDT) TO BE PRFORMED

ON ALL ROOT AND FINAL WELDS SHALL BE A VT. ALL WELDING OF

STRUCTURAL STEEL SHALL BE IN ACCORDANCE WITH (IAW) PSNS

WELD PROCEDURE WP-FAC REV A. NON-DESTRUCTIVE TESTING

(NDT) TO BE PERFORMED ON ALL ROOT AND FINAL WELDS SHALL

BE A VT.

4.3. MANUFACTURE BY CONTRACTOR: ALL WELDING SHALL BE IAW

AWS D1.1 FOR STEEL AND IAW AWS D1.2 FOR ALUMINUM.

5. CORROSION CONTROL

5.1. SURFACE PREPARATION: CLEAN FERROUS METALS BY SOLVENT

CLEANING PER SSPC-SP1, FOLLOWED BY NEAR WHITE METAL

BLAST CLEANING BARE METAL PER SSPC-SP10. LOCALIZED

SURFACE PREPS CAN BE ACCOMPLISHED UTILIZING POWER

TOOLS PER SSPC-SP11, OR HAND TOOLS PER SSPC-SP2.

5.2. PAINTING OR POWDER COAT OPTIONS:

5.2.1. MIL-PRF-23236 (2-PART EPOXY): APPLY TWO COATS. EACH

COAT 4-8 MILS DRY FILM THICKNESS (DFT). TOTAL 8-16

MILLS DFT. TOPCOAT SHALL BE A DIFFERENT COLOR THAN

THE PRIME COAT. FINAL COAT COLOR SHALL BE DESIGNATED

BY THE SHOP.

5.2.2. MIL-DTL-24441 TYPE IV (2-PART EPOXY): APPLY TWO COATS.

EACH COAT 4-6 MILS DFT. TOTAL 8-12 DFT. TOPCOAT SHALL

BE A DIFFERENT COLOR THAN THE PRIME COAT. FINAL COAT

COLOR SHALL BE DESIGNATED BY THE SHOP.

5.2.3. EPOXY OR POLYESTER POWDER COATINGS ARE ACCEPTABLE

ALTERNATIVES. USE POLYESTER POWDER COATING FOR

ITEMS/COMPONENTS EXPOSED TO ULTRAVIOLET LIGHT FOR

EXTENDED PERIODS. USE EPOXY POWDER COATING FOR

ITEMS/COMPONENTS NOT EXPOSED TO ULTRAVIOLET LIGHT

FOR EXTENDED PERIODS, SUCH AS THOSE NORMALLY

LOCATED INSIDE BUILDINGS OR STRUCTURES.

6. USE

6.1. INTENDED TO SUPPORT THE WATER FILTER ASSEMBLY FOR

DRINKING FOUNTAINS.

7. FOR TECHNICAL QUESTIONS OR COMMENTS, CONTACT S/99, S/64

PROCESS IMPROVEMENT DRAWING OFFICE BY PHONE 360-476-0318

SHEET 3 OF 6

SIZE DRAWING NO.

PI-99-05182022B C

MATERIALS LIST

PC QTY DESC MTL MTL SPEC COMMENT

1 1 PL 20" X 17" X 3/16" TH 6061-T6 ALUMINUM ASTM B221

2 2 PL 8" X 8" X 1" TH 6061-T6 ALUMINUM ASTM B221

3 2 ANGLE 4" X 2" X 1-1/2" X 1/4" TH 6061-T6 ALUMINUM ASTM B221

4 4 CAP SCREW, HEX HEAD, 5/16"-18 X 7/8" LONG 18-8 STAINLESS ASME B18.2.1

5 4 HEX NUT, 5/16"-18 THREAD 18-8 STAINLESS ASTM F594

6 4 CAP SCREW, HEX HEAD, 5/16"-18 X 1-1/8" LONG 18-8 STAINLESS ASME B18.2.1

HIDDEN HARDWARE

BEHIND PC#4

HIDDEN HARDWARE

BEHIND PC#2

SHEET 4 OF 6

SIZE DRAWING NO.

PI-99-05182022B C

20"

3"

8"

3" 10 7/8"

13 7/8"1 1/2"

1"

1 1/2" R 2"

R 2" 11/32"

7 37/64"

16 7/8"

3 55/64" 2 17/32"

PLAN VIEW

ELEVATION VIEW

PLAN VIEW

R 2 1/2"

3/4"

1 1/2"

R 2 21/64"

2 1/32"

3/8"

TYP

1/2"

TYP 2

DRILL AND TAP

5/16"- 18 THREAD

1" DEPTH

3/16"

ROUND OFF SLOT EDGES

FRONT AND BACK

O 4 1/4"

1"

SHEET 5 OF 6

SIZE DRAWING NO.

PI-99-05182022B C

O 11/32"

TYP

1 1/2"

1 1/2"

3/4"

TYP

3/8"

TYP

R 1/4"

TYP

4"

R 3/4"

TYP

ELEVATION SIDE

ELEVATION BACK

PLAN VIEW

SHEET 6 OF 6

SIZE DRAWING NO.

PI-99-05182022B C

MINIMUM DISTANCE MAXIMUM DISTANCE

LAYOUT SPECS

5 3/16" 8 1/16"