Design_Intent_Document_Revised_6.10.2025.pdf

Design Intent Document Sign Design Details and Specifications 20 June, 2024 - Revised 10 June, 2025

City of St. Cloud Downtown Wayfinding

System

Table of Contents

General Specifications 3

Graphic Standards

Sign Palette

Sign Details

Sign Location and Messages

Sign Type B - Large Vehicular Sign

Sign Type C - Small Vehicular Sign

Sign Type D - Parking Directional

Sign Type E - Pedestrian Kiosk

Sign Type F - Pedestrian Directional & Map

Sign Type G - Pedestrian Directional

Legend - Labels

Location Plan & Message - Sign Type A

Location Plan & Message - Sign Type B

Location Plan & Message - Sign Type C

Location Plan & Message - Sign Type D

Location Plan & Message - Sign Type E & G

Sign Maintenance and Longevity

Construction Details

General Specifications

4City of St. Cloud Wayfinding System General Specifications 06/10/2025

PART 1 - GENERAL SPECIFICATIONS

1.1 SUMMARY

A.This Section includes:

1. Aluminum signs and supports.

2. Wayfinding signs and directionals.

3. Gateway Signs.

4. Mapping & branding signage.

1.2 PERFORMANCE REQUIREMENTS

A. Structural Performance: Provide signs and anchorage points capable of withstanding the effects of gravity, wind, snow, and seismic loads and stresses, as indicated in the General Notes of the Structural Drawings determined according to the local building code and authorities having jurisdiction, reference specification section 01 40 00 Quality for Engineer.

1. Deflection of signs and supports in vertical and horizontal direction shall be no greater than 1/360 of clear span or .75-inch (19 mm), whichever is smaller.

B. Thermal Movements: Provide post and panel signs that allow for thermal movements resulting from the following maximum change (range) in ambient and surface temperatures by preventing buckling, opening of joints, overstressing of components, failure of connections, and other detrimental effects. Base engineering calculation on surface temperatures of materials due to both solar heat gain and nighttime-sky heat loss.

1. Temperature Change (Range): 120 deg F (67 deg C), ambient;

180 deg F (100 deg C), material surfaces.

C. Moisture Resistance: Provide signs and supports that are designed to withstand the detrimental effects of moisture, preventing corrosion, rotting, warping, delamination, or other forms of deterioration, as follows:

1. The materials used in the construction of the signs and supports shall be resistant to moisture or adequately protected against it by suitable coatings, sealants, or barriers.

2. All joints, connections, and fasteners shall be designed to prevent water infiltration and to allow for the expansion and contraction of materials due to changes in moisture content.

3. The sign shall be installed with a suitable slope to allow for the drainage of water and prevent ponding or accumulation of moisture on any surface of the sign or support.

D. Sign lifespan requirements: Provide the following minimum requirements:

1. UV resistance: The sign should have a UV resistance rating of at least 7, as measured by the Xenon-Arc test (ASTM G155 or equivalent).

2. Lifespan: The sign should have a minimum lifespan of 5 years under normal outdoor conditions, as determined by the accelerated weathering test (ASTM G155 or equivalent).

3. Color retention: The sign should maintain its original color and appearance for the duration of its lifespan under normal outdoor conditions, with no significant fading or discoloration.

1.3 SUBMITTALS

A. Product Data: Submit manufacturer’s technical data and installation instructions relative to materials, dimensions of individual components, profiles, and finishes for each type of material required.

B. Shop Drawings: Submit shop drawings for fabrication and installation/ mounting method for each typical sign type, or display type. Include plans, elevations, Iso views and large scale details of each element.

Include large scale sections of typical members and other components. Show fabrication joints, seams, grain direction and fasteners. Show anchors, grounds, reinforcement, accessories, layout, and installation details.

1. For items required to comply with design loads, include structural analysis data signed and sealed by the licensed professional engineer responsible for their preparation if not previously provided by the client.

2. Submit graphic layouts for verification, including outline of sign face, character spacing, line spacing, and copy composition.

3. Engineering, document & sample review, fabrication, and construction schedule.

4. Submit drawings in 11-inch by 17-inch format unless otherwise requested by the client.

material showing finishes, colors, surface textures and qualities of manufacturer and design of each component including graphics. One sample set to be kept by Client, contractor, and client as a record to later match against items in the field.

1. Submit full-size sample first article units, per Section 3.6, before production run is commenced. Acceptable units may be installed as part of the work.

D. Maintenance Data: Provide a Maintenance and Operating Manual comprised of cleaning and operations needs for each sign/graphic/ display type. This shall include information on repair due to common vandalism, changing of messages and parts replacement needs per material vendor requirements. Include manufacturers’ brochures and parts lists describing the actual materials used in the work, including metal alloys, finishes, electrical components and other major components. Provide working art file templates to the client for future use.

1.4 QUALITY ASSURANCE

A. Professional Engineer Qualifications: A professional engineer who is legally qualified to practice in jurisdiction where Project is located and who is experienced in providing engineering services of the kind indicated. Engineering services are defined as those performed for design and installations of signs, and miscellaneous supports that are similar to those indicated for this project.

B. Manufacturer Qualifications: All fabrication within this section shall be performed by a manufacturer with a minimum of five (5) years experience producing and installing Clientural signs, and a minimum of five (5) years experience producing compliant signs as specified in ANSI 117.1 (1986), Manual on Uniform Traffic Control Devices (MUTCD), Minimum Guidelines and Requirements for Accessible Design (MGRAD), Uniform Federal Accessibility Standards (UFAS) and Americans with Disabilities Act Accessibility Guidelines (ADAAG).

C. Drawings and Specifications: The Client will provide electronic files of typical sign layout drawings in Adobe Illustrator CC format. For electronic files requested in any format other than Adobe Illustrator CC, the Contractor shall reimburse the Client, for additional services required of the Client for converting the electronic files. Client will provide electronic files indicating fonts, icons, designs, and key visual parameters of the design intent. Fabricator shall develop and produce final, high resolution production-ready artwork based on these guides and the details on the Drawings – this includes any up-sampling or interpolation required for large scale photo based graphics.

1. Drawings and specifications indicate spacing of members, sizes of components, profile, dimensions, materials, and design, assembly and fabrication requirements for the signs.

2. Requests for deviations from indicated dimensions and profiles will be considered provided that the intended aesthetic effect is not modified, as judged and approved solely by the client. If modifications are proposed, submit comprehensive explanatory data to client for review.

D. Uniformity of Manufacturer: For each separate type of material, finish or sign or display type, obtain signs from a single manufacturer to ensure consistency.

5City of St. Cloud Wayfinding System General Specifications 06/10/2025

1. Manufacturer’s name, trade name, or trade mark shall not appear on any visible surface.

E. Adhesion Testing – For all applied graphic films and vinyl products, perform adhesion tests on accordance with manufacturer’s specifications. Provide results of adhesion testing to the client and the contractor for approval.

F. Welding Standards: Qualify procedures and personnel according to the following:

G. Aesthetic Requirements: Provide copy with straight and true edges;

space characters with tracking and leading as indicated; reproduce type faces accurately with square corners and even curves; provide uniform letters and symbols; and provide smooth finishes with no visible imperfections.

H. Regulatory Requirements – Comply with applicable requirements of the applicable laws and authorities. Obtain necessary approvals and permits from all such authorities as required.

I. ADA Accessibility Guidelines: All signage shall comply with the ADA Accessibility Guidelines where applicable. Characters and graphics, including but not limited to, copy height, letter stroke, symbols, materials, and finishes indicated on the Drawings are intended as guidelines for compliance. Implement each applicable ADA Guideline.

Should conflicts arise, notify the Client before proceeding.

J. Mockups: Provide one mockup sign of each type indicated in the schedule at the end of this Section.

K. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, Article 100, by a testing agency acceptable to authorities having jurisdiction, and marked for intended use.

1.5 PROJECT CONDITIONS

A. Field Measurements: Verify dimensions of install locations for all items by field measurement before fabrication and indicate measurements, and any obstructions on Shop Drawings.

1. Established Dimensions: Every effort shall be made to verify dimensions in the field before production. In the case where field measurements cannot be made without significantly delaying the Work, the Fabricator is to review the established installation location and dimensions with the contractor and the client. The Contractor is responsible to provide an installation surface that accommodates the established dimensions identified.

1.6 COORDINATION AND SCHEDULE

A. Installation: Coordinate installation with the Contractor for all sign and renovation projects. For items supported by or anchored to permanent construction, coordinate specific requirements for types and placement of anchorage devices and similar items to be used for attaching signs and displays.

1. For any items supported by, anchored to or mounted to permanent construction, furnish templates to the Contractor for installation of blocking, anchorage devices, and electrical conduits.

B. Prepare a schedule indicating engineering, sample and material reviews, print proofs, fabrication, delivery, installation, and final inspection of the Work. Submit this schedule to the client for approval and coordination with other work at the Project Site.

1.7 DELIVERY, STORAGE AND HANDLING

damage, soiling, and deterioration. Minor damage to finishes may be repaired provided the final finishes are equal to the original finishes, are without noticeable flaws, and are acceptable to the Client. If not in like-new condition, or if not acceptable to the Client, remove and replace damaged items with new signs.

C. Coordinate delivery and storage of sign materials with the Contractor in advance. Schedule delivery to minimize storage requirements.

Materials stored at the Project Site without prior approval may have to be relocated at the Fabricator’s expense.

1.8 MAINTENANCE

A. Furnish a list of cleaning materials appropriate for maintenance of signs, graphics and displays to both the Client and the Contractor.

Provide written instructions for proper maintenance, electrical access, and character and lighting replacement procedures. Include recommended methods for removal of residual adhesives from wall surfaces after removal of adhered items.

PART 2 - PRODUCTS

2.1 MATERIALS, GENERAL

A. Use materials of size and thickness indicated or, if not indicated as required to produce strength and durability in finished product for use intended. Work to dimensions shown or accepted on shop drawings, using proven details of fabrication and support. Use type of materials shown or specified for various components of work.

B. All materials shall be free from defects impairing strength, durability, and appearance. No fabrication or installation materials or procedures shall be used that will in any way change the usual quality or in any manner have an adverse effect on existing materials and surfaces.

All materials shall be new stock, unless the Client has specified a reclaimed or recycled material.

C. Graphic Content and Style: Provide graphic layouts and sign copy that complies with requirements indicated in this document and Signage Message Schedule and on preliminary artwork supplied by Client for size, fonts, style, spacing, content, mounting height and location, materials, finishes, and colors.

2.2 MATERIALS

A. General: For the fabrication of exposed metal work, use only materials which are smooth and free of surface blemishes including pitting, roughness, seam marks roller marks, and trade names. Do not use materials which have stains or discolorations.

temper recommended by aluminum producer and finisher for type of use and finish indicated, and with at least the strength and durability properties of alloy 5005-H15.

1. Thickness: Provide aluminum sheets and plates in sizes specified or indicated on the Drawings.

C. Aluminum Extrusions: ASTM B 221 (ASTM B 221M), alloy and temper recommended by aluminum producer and finisher for type of use and finish indicated, and with at least the strength and durability properties of alloy 6063-T5.

D. Stainless Steel: Grade and type designated below for each form required:

6City of St. Cloud Wayfinding System General Specifications 06/10/2025

E. General: Plastic shall be free of imperfections from forming or fabrication. All surfaces shall be free from scratches and shall be cleaned and polished per manufacturer’s instructions at completion of installation. Edges shall be flame polished, free of saw marks and chips, and be eased, unless otherwise noted.

F. General: Provide vinyl graphic film suitable for interior and exterior applications of types indicated below.

removable adhesive is specified).

3. Overlaminate: Include a Matte overlaminate for all interior vinyl graphic films unless otherwise indicated in this document.

4. Installation: Use minimum overlapping seams advised by the manufacturer.

G. Basis-of-Design Products: The design is based on the products named. Subject to compliance with requirements, provide either the named products or comparable product by one of the other specified manufacturers. Comparable products are subject to review and approval through the submittal process specified. Note: All film/ vinyl materials require an adhesion test prior to printing to confirm successful adhesion.

1. Opaque Vinyl Film: Non-reflective, pre-spaced die-cut letters and film, supplied in specified typeface, color, and spacing on a quick-release backing sheet.

2. Transparent Vinyl Film: 3M Scotchcal™ Clear Graphic Film 8626

ES.

3. Translucent Vinyl Film: 3M Scotchcal™ Translucent Graphic Film

8628 ES.

4. Opaque Imaging Media for smooth surfaces: 3M Controltac Graphic Film with Comply v3 Adhesive IJ180CV3-10 with 3M Scotchcal Matte Overlaminate 8510M

a. Provide alternate pricing for 3M Scotchcal Graphic Film with Comply Adhesive IJ40C-10R with 3M Scotchcal Matte Overlaminate 8510M

5. 3M Scotchcal™ for Textured Surfaces; Series IJ8624 with 3M Luster Overlaminate 8524.

H. Available Manufacturers: Subject to compliance with requirements, manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following:

2.3 HARDWARE, FASTENERS, AND ADHESIVES

A. Fasteners: Unless otherwise indicated, use concealed fasteners fabricated from metals that are non-corrosive to either the sign material or the mounting surface. If concealed fasteners are not practical or possible, provide vandal-resistant fasteners.

B. Fabricate brackets and fittings for bracket-mounted signs from materials compatible with panel sign construction and mounting conditions indicated. Factory-paint brackets in color matching background color of panel sign.

1. Steel Tubing: Cold-formed steel tubing complying with ASTM A 500, Grade B.

2. Structural Steel Shapes, Plates, and bars: Cold formed steel fabrications complying with ASTM A36.

C. Anchors and Inserts: Use non-ferrous metal or hot-dipped galvanized anchors and inserts for exterior installations and elsewhere as required for corrosion resistance. Use toothed steel or lead expansion bolt devices for drilled-in-place anchors. Furnish inserts, as required, to be set into concrete or masonry work.

1. For attachment to metal panels, use #12 stainless steel, Type 410, self-tapping screws with integral neoprene washers.

D. Adhesives: Provide products equal to “Depend 330” as manufactured by Loctite Acrylic Adhesives. (216)881-2828. Fabricator shall verify with painting manufacturer compatibility of the adhesive to the paint.

E. Very High Bond (VHB) Tape: Provide 3M (or approved equal) VHBm tape at the appropriate thickness/strength required for the weight and size of each item installed.

F. Silicone Adhesive: Provide liquid silicone adhesive (sealant) with a methanol or acetic cure as recommended by the sign fabricator.

G. VOC Content of Interior Sealants: Sealants and sealant primers used inside the weatherproofing system shall comply with the following limits for VOC content when calculated according to 40 CFR 59, Subpart D (EPA Method 24):

H. Spacers: Provide Manufacturer’s standard spacers when necessary.

2.4 GRAPHIC REQUIREMENTS

design intent shown in this document. Some variation in tracking and character width to ensure messages fit, may be acceptable.

Any variations to be reviewed and approved by the Client.

2. Characters indicated on the Drawings are intended as guide lines for layouts and font size only, and are based on scale calculations of the message lengths within given and estimated sign areas. The actual copy required on individual signs is indicated in the signage message schedule. Should conflicts arise in the final message layout, notify the Client before proceeding.

3. Spelling and punctuation shall be correct. Should an error in spelling or punctuation be found, or the spelling appears questionable notify the Client before proceeding.

4. Align letter forms to maintain a baseline parallel to the sign format, unless otherwise indicated. Maintain uniform margins in sign layouts.

5. Building Identification Signs with Name and Tenants: Client will determine names for each individual suite or office.

6. Provide digital proofs of final signage layouts to the Client for approval before fabrication.

B. Production-Ready Artwork: This document includes specifications for all visual elements including, but not limited to, type, symbols, logos, photography, artwork, and arrows. The Fabricator is to create final production-ready artwork necessary to complete all signs and graphics based on the design intent included in this document.

1. Production-ready artwork is to be high enough resolution to provide crisp edges and lines for all vector artwork, and to avoid any visible blurring or pixelation of photographic images.

Fabricator to interpolate and up-sample photographic artwork as required for the installation location and viewing distance.

Do not use the construction documents as production art. The Fabricator is to provide printed proofs of all graphics to ensure color and resolution are acceptable – samples to include a swatch of the 100% full size graphic as well as a scaled version of the entire art work – printed on the specified substrate.

2. Silkscreens shall be executed from photoscreens or negatives.

Pattern cut screens may be used where non-repeat copy is re-quired; however, copy mask shall be equivalent to photoscreen quality. Do not use construction documents as production art.

7City of St. Cloud Wayfinding System General Specifications 06/10/2025

2.5 FABRICATION, GENERAL

A. General: Fabricate signs to comply with requirements indicated on drawings for materials, thicknesses, finishes, colors, designs, shapes, sizes, and details of construction.

1. Form exposed faces and sides of signs to produce surfaces free from warp, distortion, and “oil canning.”

a. Include internal bracing for stability and attachment of mounting accessories as required.

b. Cut metal edges on a continuous line and sand smooth.

Seams shall be straight and symmetrical.

c. Form exposed connections with hairline joints, flush, and smooth.

d. Form exposed work true to line and level with sharp angles, surfaces, and edges. Ease exposed edges to a radius of approximately .03125-inch (0.8 mm) unless otherwise indicated. Form bent-metal corners to smallest radius possible without causing grain separation or cracking of applied finishes.

2. Welding, when necessary, shall be of the appropriate type to minimize permanent distortions of flat surfaces. Remove welding flux, oxides and discolorations by pickling or grinding, so that these areas match the finish of the adjacent areas. Repair damage caused by the fabrication by grinding, polishing, or buffing.

a. Weld corners and seams continuously, complying with AWS recommendations. At connections, grind exposed welds smooth and flush to match and blend with adjoining surfaces.

3. Cut, reinforce, drill, and tap miscellaneous metal work as indicated to receive finish hardware and similar items.

4. Produce smooth, even, level sign panel surfaces, constructed to remain flat under installed conditions within a tolerance of plus or minus one percent measured diagonally from corner to corner.

5. Fabricate, brackets and fittings for signs to suit sign panel construction and mounting conditions indicated. Connections, angles, shapes and details shown are suggestive and are to be sized, reinforced and detailed as required. Details not shown are to be equal in quality to those detailed. Factory paint brackets in color matching background color of sign panel.

6. Provide concealed access to internal components for relamping and service. Service access shall be waterproof and secured against vandalism.

weatherproofing construction, including weather-stripping, weeping, and venting provisions for condensation control.

B. Metal signs facing and cladding shall be aluminum unless otherwise indicated or specified in this document.

C. Where galvanized steel and aluminum meet, the materials shall be materially isolated from one another to prevent electrolytic action.

Aluminum joints and connections shall be heli-arc welded and flush, true, ground, and polished smooth and without defects. Character forms shall be cut true to typeface with no burns or imperfections of any kind.

D. Internal Structure: Provide completely hidden, internal structures for support and anchorage, unless indicated otherwise on the drawings.

Primary support structure shall hot dipped galvanized steel or aluminum.

2.6 PANEL SIGNS

A. Exterior Plaque Sign: Unless otherwise specified in this document, provide products fabricated from 0.125-inch aluminum plate with

0.030 inch thick double face tape mounting and silicone adhesive. All exterior signage is to include weep/drain holes as required.

0.125-inch- (3.2-mm-) thick aluminum sheet.

2. Panel Finish: Unless otherwise specified in this document, baked enamel.

a. Panel Finish: Manufacturer’s standard semigloss finish with UV inhibitors.

b. Provide clips welded to back of panels for installation without visible fasteners.

3. Frame Material: Unless otherwise specified in this document, extruded aluminum, fabricated to profile indicated; comply with the following:

8City of St. Cloud Wayfinding System General Specifications 06/10/2025

PART 3 - EXECUTION

3.1 PREPARATION

A. General: Examine area, surfaces and conditions under which the work is to be installed. Notify the Contractor in writing of conditions detrimental to the proper and timely completion of the work. Starting work implies acceptable surfaces and conditions.

3.2 INSTALLATION

A. General: Locate signs, graphics and displays where shown on Sign Location Plan, attaching to substrates in accordance with manufacturer’s instructions, unless otherwise indicated.

1. Install signs level, plumb, and at heights indicated, with surfaces free from distortion and other defects in appearance.

B. Surfaces under adhesive applied units shall be smooth, clean, and free of dust, grease, fingerprints, or other foreign matter. All adhesives required shall be used in accordance with recommendations made by the manufacturer of the material to be laminated or adhered. No adhesives that will fade, discolor, or delaminate because of ultraviolet light or heat shall be used. Adhesives shall not change the color of or deteriorate the materials to which they are to be applied. The adhesives shall be of a non-staining, non-yellowing quality. All visible joints shall be free from air bubbles and other defects.

C. Within one week of scheduled completion of installation, prepare a punch list itemizing:

D. Repair or replace damaged units as required after client’s final inspection.

3.3 PATCH AND ADJUST

A. Patch existing surfaces damaged because of work under this section. Patch with same materials as existing. Fabricator shall paint and harmoniously blend and contour all repairs to match adjoining conditions so that they are not noticeable to view.

B. Touch-up any marks or nicks in painted finishes of all signs and adjacent structures. Touch-up shall be the same paint product as used for this sign finish. Touch up areas should blend with surrounding areas and not be noticeable to view.

C. Corrosion Protection: Coat concealed surfaces of aluminum that will be in contact with grout, concrete, masonry, wood, or dissimilar metals with a heavy coat of paint.

D. Galvanized Surfaces: Clean field welds, bolted connections, and abraded areas and repair galvanizing to comply with ASTM A 780, Annex A2.

3.4 CLEANING AND PROTECTION

A. At completion of installation, clean exposed surfaces in accordance with the manufacturer’s instructions. All items shall be free of glue, fingerprints, dirt, grease, or any other imperfections.

B. Evidence of installation work or damages incurred on other surfaces shall be cleaned or repaired prior to completion of work. Protect units from damage until acceptance by Client.

C. Remove all packing and construction materials from site. Leave premises clean, ready for work under other contracts or ready for use.

D. Instruct the Client in writing as to the correct operation and maintenance of all signs and sign components per materials and manufacturer requirements.

3.5 SCHEDULE OF MOCKUPS

A. Provide a physical and digital mock-up (partial for large items;

complete for smaller items) of each sign/display type requested at the fabrication facility for review. The requested mock-ups shall be coordinated with Client o verify selections made under sample submittals and to demonstrate aesthetic effects and set quality standards for materials and fabrication.

B. When accepted, mock-up shall serve as the standard for materials, workmanship, and appearance for the work throughout the project.

C. Provide work-in-progress sign elements reviews. Scheduled or unscheduled viewings at the Fabrication Facility may be initiated by the Client’s Representative as deemed necessary to ensure continued quality control and make any adjustments required during fabrication.

Unsatisfactory items are to be corrected by the Fabricator as directed by the Client or client’s representative.

D. Scaled mock up of graphic artwork + Full size print swatch of all graphic prints.

3.6 WARRANTY

A. Submit to the Client a 1-year written warranty (effective the date of final acceptance/inspection `— see 3.2.D) covering all signs fabricator will agree to repair or replace defective signs. Upon notification of such defective signs within the warranty period, make necessary repairs or replacement at the convenience of the Client’s Representative.

B. Submit to the Client a 1 year written warranty, based on ASTM set standards, warranting that the factory-applied finishes will not develop fading or non-uniformity of color or shade. Stating that is the signs crack, peel, pit, corrode or otherwise fail because of defects in materials or workmanship within the following defined limits, the fabricator shall rectify the defects. Upon notification of such defects within the warranty period, the fabricator shall be responsible to make all necessary repairs or replacement at the convenience of the client.

Graphic Standards

10Scale: NTS

DATE OF ISSUE

REVISION

06/20/2024

#1 - 06/10/2025

City of St. Cloud Wayfinding System St. Cloud, FL

A GAI Consultants, Inc. Service Group

618 E. South Street Suite 700 Orlando, Florida 32801 T 407.423.8398 gaiconsultants.com/communitysolutions

Graphic Standards

TYPOGRAPHY &

TYPEFACES

This page provides a reference for the typefaces for the Wayfinding Signage System. Typefaces may not be changed.

During fabrication, the height and width ratio of letter forms must be maintained proportionately.

Vehicular Signage:

Marquee, Vehicular Directional, and Parking Directional Signs typeface for vehicular signs is Highway Gothic Type D. Signs placed on roads with a speed limit of over 25MPH shall have 6” high type.

Signs placed on roads with a speed limit of 25MPH and lower shall have 4” high type. Type should be upper and lower case.

Pedestrian Signage:

Minimum 1” high copy is recommended for pedestrian directional and kiosk signs.

Typeface A - Highway Gothic Type D (FOR VEHICULAR USE ONLY)

ABCDEFGHIJKLMNOPQUSTUVWXYZ

abcdefghijklmnopqrstuvwxyz� 1234567890

Typeface C - Grange Heavy Condensed

ABCDEFGHIJKLMNOPQUSTUVWXYZ

abcdefghijklmnopqrstuvwxyz� 1234567890

Typeface D - Grange Medium

ABCDEFGHIJKLMNOPQUSTUVWXYZ

abcdefghijklmnopqrstuvwxyz� 1234567890

Typeface E - Grange DemiBold

ABCDEFGHIJKLMNOPQUSTUVWXYZ

abcdefghijklmnopqrstuvwxyz� 1234567890

Typeface E - Grange Bold

ABCDEFGHIJKLMNOPQUSTUVWXYZ

abcdefghijklmnopqrstuvwxyz� 1234567890

Typeface E - Grange Heavy

ABCDEFGHIJKLMNOPQUSTUVWXYZ

abcdefghijklmnopqrstuvwxyz� 1234567890

Typeface B - Grange Medium Condensed

ABCDEFGHIJKLMNOPQUSTUVWXYZ

abcdefghijklmnopqrstuvwxyz� 1234567890

11Scale: NTS

REVISION

06/20/2024

#1 - 06/10/2025

City of St. Cloud Wayfinding System St. Cloud, FL

A GAI Consultants, Inc. Service Group

618 E. South Street Suite 700 Orlando, Florida 32801 T 407.423.8398 gaiconsultants.com/communitysolutions

Graphic Standards

COLORS &

MATERIALS

Consistent use of a color palette creates a recognizable “system”.

The Color Palette found on the following pages provides a reference for specifying a paint color or material.

The Fabricator is required to submit painted color chips and material samples for approval prior to sign fabrication.

The ADA requires a minimum of 70% contrast between text and background for legibility.

Paint Colors Vinyl Colors

Color/Code Color/Code

White WhitePMS White 3M Scotchcal

Surface applied, exterior sign paint and protective top coat: Acrylic Polyurethane w/ UV inhibitor, finished with Clear Coat Satin finish.

Engineer-grade retro reflective vinyl meeting or exceeding FDOT require-ments for day and night driving.

Surface applied, exterior sign paint and protective top coat: Acrylic Polyurethane w/ UV inhibitor, finished with Clear Coat Satin finish.

Background & Characters 3M cus-tom inks applied directly to 3930 with 3M approved clear UV/Graffiti Vinyl Over-laminates.

Background & Characters 3M cus-tom inks applied directly to 3930 with 3M approved clear UV/Graffiti Vinyl Over-laminates.

Surface applied, exterior sign paint and protective top coat: Acrylic Polyurethane w/ UV inhibitor, finished with Clear Coat Satin finish.

Surface applied, exterior sign paint and protective top coat: Acrylic Polyurethane w/ UV inhibitor, finished with Clear Coat Satin finish.

Surface applied, exterior sign paint and protective top coat: Acrylic Polyurethane w/ UV inhibitor, finished with Clear Coat Satin finish.

Surface applied, exterior sign paint and protective top coat: Acrylic Polyurethane w/ UV inhibitor, finished with Clear Coat Satin finish.

PMS 7692 C

3M Scotchcal

3M Scotchcal

PMS 412 C

PMS 364 C

PMS 533 C

PMS Black

Blue Blue

Navy Blue

Green

Navy Blue

Black

Orange

Name NameSpecification SpecificationProcess Process

P1 V1

V2

V3P3

P2

P4

P5

P6

Sign Palette

DISTRICT NAME

Public Parking

City Hall Downtown

Aquatics Ctr Civic Center

DISTRICT NAME

City Hall Aquatics Ctr

Civic Center

City of St. Cloud Wayfinding System St. Cloud, FL 13DATE OF ISSUE

REVISION

06/20/2024

#1 - 06/10/2025

A GAI Consultants, Inc. Service Group

618 E. South Street Suite 700 Orlando, Florida 32801 T 407.423.8398 gaiconsultants.com/communitysolutions

Scale: NTS Sign Palette

B C D Large Vehicular Sign

(FDOT roads) Small Vehicular Sign

(City roads) Parking Directional

Destination

STREET NAME

STREET NAME

Destination Destination DestinationDestination Destination

DOWNTOWN ENTERTAINMENT DISTRICT

DOWNTOWN ENTERTAINMENT DISTRICT

STREET NAME

13TH STREET / US HIGHWAY 192

13TH STREET / US HIGHWAY 192 13TH STREET / US HIGHWAY 192

12TH STREET12TH STREET 12TH STREET

11TH STREET 11TH STREET11TH STREET

10TH STREET10TH STREET 10TH STREET

9TH STREET9TH STREET 9TH STREET

M

AS

SA

CH

US

ET

TS

A

VE

NU

E

K

EN

TU

CK

Y

AV

EN

UE

K

EN

TU

CK

Y

AV

EN

UE

NE

W

YO

RK

A

VE

NU

E

NE

W

YO

RK

A

VE

NU

E

PE

NN

SY

LV

AN

IA

A

VE

NU

E

PE

NN

SY

LV

AN

IA

A

VE

NU

E

FL

OR

ID

A

AV

EN

UE

FL

OR

ID

A

AV

EN

UE

OH

IO

A

VE

NU

E

M

AS

SA

CH

US

ET

TS

A

VE

NU

E

8TH STREET 8TH STREET 8TH STREET

58 25

73 80

9 24

Handyman Hardware Old Fashion Cigar Southern Roots Antiques Oro D’Italia Sincerely Yours

The Pink Paisley Boutique Gun Store

Solana’s Handmade Cake Pasteries & More

Chime & Time Clock Repair Blissology

Kuppa Thyme Tea Room Phyre Saloon & Steakhouse Crust & Crumb Social House Sweet Spot Snoballs

Chimento’s Spaghetti House Loading Gastrobrunch Garage Bar Island Cloud Grill Granny's Southern Smokehouse Breeze Madilynns Craft Coffee Shop

Nutrition Zone Savvy Sweets Bakery Fortuna Bakery & Cafe The Black Squirrel Bookstore & Speakeasy

10th Street Produce and Deli

Lafontaine French Macarons LLC

Blush Boutique and Salon The Color Loft Rayzor Edge Soul 2 Sole Massage Salon Emvy

Creative Printing Services Lewis and Massey. PA State Farm Insurance Snow Construction Arnco Construction Godwin Realty Group Pro Auto Detailing 3 Lil Birds Tattoo Gallery Andy’s Auto Service LLC Cloud Care Medicine Family Dentistry- James Chen Family Dentistry of St. Cloud Fisk Funeral Home Elite Metro Hemphill Accounting Services Homepride Group at EXP Realty Joe's Auto Services Center Inc Keystone Residential Group Kisselback Insurance Agency

Precision Hearing Aids

Insurance Office of America

Gio Meza Esthetician & Academy Lymphatic Drainage & Aesthetics, Post-Op Recovery Massage & Care

Johnson’s Martial Art The Stained Glass Lady JMB Dance Academy Just A Glazin New Journey Jiu Jitsu

American Legion

VFW

Healthy Start Coalition

Morse Market

Askew Jewelers Five Point Funiture & Auction

Smart Devices 911 Jammers Music Center

Batch of Music Hodgins Home Appliance Store 34 Fireflies Sudz Bath + Body Essentials 3Beez Honey Farm

Curios Cottage Kisselback Ford The Lavender Patch Goat Card Shop

49 WAXX Bar H & Wes Jaleisha Dee Nail Salon & Spa MBK Beauty Spa

RETAIL SERVICES

ENTERTAINMENTFOOD/BAR

COMMUNITY

GROCERY

SALON/SPA

The St. Cloud Hotel The Hunters Arms Hotel

LODGING

Main St.

O�ce

Main St.

O�ce

St. Cloud Twin

St. Cloud Twin

Camber of Commerce Camber of Commerce

The Woman’s Club of St. Cloud

The Woman’s Club of St. Cloud

Veteran’s Memorial Park

Veteran’s Memorial Park

Heritage MuseumHeritage Museum

City Hall

DOWNTOWN

ENTERTAINMENT

DISTRICT

Veterans of Foreign Wars

Veterans of Foreign Wars

Centennial Park

Centennial Park

Community Garden

Community Garden

Lorem ipsum dolor sit amet, consectetuer adipiscing elit, sed diam nonummy nibh euismod tincidunt ut laoreet dolore magna aliquam erat volutpat. Ut wisi enim ad minim veniam, quis nostrud exerci tation ullamcorper suscipit lobortis nisl ut aliquip ex ea commodo consequat. Duis autt accumsan et .

SCAN HERE FOR...

13TH STREET / US HIGHWAY 192

13TH STREET / US HIGHWAY 192 13TH STREET / US HIGHWAY 192

12TH STREET12TH STREET 12TH STREET

11TH STREET 11TH STREET11TH STREET

10TH STREET10TH STREET 10TH STREET

9TH STREET9TH STREET 9TH STREET

M

AS

SA

CH

US

ET

TS

A

VE

NU

E

K

EN

TU

CK

Y

AV

EN

UE

K

EN

TU

CK

Y

AV

EN

UE

NE

W

YO

RK

A

VE

NU

E

NE

W

YO

RK

A

VE

NU

E

PE

NN

SY

LV

AN

IA

A

VE

NU

E

PE

NN

SY

LV

AN

IA

A

VE

NU

E

FL

OR

ID

A

AV

EN

UE

FL

OR

ID

A

AV

EN

UE

OH

IO

A

VE

NU

E

M

AS

SA

CH

US

ET

TS

A

VE

NU

E

8TH STREET 8TH STREET 8TH STREET

58 25

73 80

9 24

Handyman Hardware Old Fashion Cigar Southern Roots Antiques Oro D’Italia Sincerely Yours

The Pink Paisley Boutique Gun Store

Solana’s Handmade Cake Pasteries & More

Chime & Time Clock Repair Blissology

Kuppa Thyme Tea Room Phyre Saloon & Steakhouse Crust & Crumb Social House Sweet Spot Snoballs

Chimento’s Spaghetti House Loading Gastrobrunch Garage Bar Island Cloud Grill Granny's Southern Smokehouse Breeze Madilynns Craft Coffee Shop

Nutrition Zone Savvy Sweets Bakery Fortuna Bakery & Cafe The Black Squirrel Bookstore & Speakeasy

10th Street Produce and Deli

Lafontaine French Macarons LLC

Blush Boutique and Salon The Color Loft Rayzor Edge Soul 2 Sole Massage Salon Emvy

Creative Printing Services Lewis and Massey. PA State Farm Insurance Snow Construction Arnco Construction Godwin Realty Group Pro Auto Detailing 3 Lil Birds Tattoo Gallery Andy’s Auto Service LLC Cloud Care Medicine Family Dentistry- James Chen Family Dentistry of St. Cloud Fisk Funeral Home Elite Metro Hemphill Accounting Services Homepride Group at EXP Realty Joe's Auto Services Center Inc Keystone Residential Group Kisselback Insurance Agency

Precision Hearing Aids

Insurance Office of America

Gio Meza Esthetician & Academy Lymphatic Drainage & Aesthetics, Post-Op Recovery Massage & Care

Johnson’s Martial Art The Stained Glass Lady JMB Dance Academy Just A Glazin New Journey Jiu Jitsu

American Legion

VFW

Healthy Start Coalition

Morse Market

Askew Jewelers Five Point Funiture & Auction

Smart Devices 911 Jammers Music Center

Batch of Music Hodgins Home Appliance Store 34 Fireflies Sudz Bath + Body Essentials 3Beez Honey Farm

Curios Cottage Kisselback Ford The Lavender Patch Goat Card Shop

49 WAXX Bar H & Wes Jaleisha Dee Nail Salon & Spa MBK Beauty Spa

RETAIL SERVICES

ENTERTAINMENTFOOD/BAR

COMMUNITY

GROCERY

SALON/SPA

The St. Cloud Hotel The Hunters Arms Hotel

LODGING

Main St.

O�ce

Main St.

O�ce

St. Cloud Twin

St. Cloud Twin

Camber of Commerce Camber of Commerce

The Woman’s Club of St. Cloud

The Woman’s Club of St. Cloud

Veteran’s Memorial Park

Veteran’s Memorial Park

Heritage MuseumHeritage Museum

City Hall

DOWNTOWN

ENTERTAINMENT

DISTRICT

Veterans of Foreign Wars

Veterans of Foreign Wars

Centennial Park

Centennial Park

Community Garden

Community Garden

Lorem ipsum dolor sit amet, consectetuer adipiscing elit, sed diam nonummy nibh euismod tincidunt ut laoreet dolore magna aliquam erat volutpat. Ut wisi enim ad minim veniam, quis nostrud exerci tation ullamcorper suscipit lobortis nisl ut aliquip ex ea commodo consequat. Duis autt accumsan et .

SCAN HERE FOR...

City of St. Cloud Wayfinding System St. Cloud, FL 14Scale: 1/2” = 1’

DATE OF ISSUE

REVISION

06/20/2024

#1 - 06/10/2025

A GAI Consultants, Inc. Service Group

618 E. South Street Suite 700 Orlando, Florida 32801 T 407.423.8398 gaiconsultants.com/communitysolutions

Sign Palette

E F GPedestrian Kiosk * Pedestrian Directional & Map *

Pedestrian Directional * Sign type F is an alternate for E and serve the same wayfinding function. City to determine which type shall be used.

Sign Details

City Hall Aquatics Ctr

Civic Center

DISTRICT NAME

City Hall Aquatics Ctr

Civic Center

Detail - Sign Face scale: 1”=1’

Front View Side View

10 3/4"

6"

6 1/2"

3/4" 1'-3"

6 1/4"

2 3/4"

6 1/4"

6" 6"

2 3/4"

Vector logo to be provided by Designer or Client

2'-8"

10 3/4"

1'-5 1/2"

5"

1'-5"1'-5"1'-5"

2 3/4" 11 1/2"

7 1/4"

1"

1"

DISTRICT NAME

Public Parking

City Hall Downtown

Aquatics Ctr Civic Center

DISTRICT NAME

City Hall Aquatics Ctr

Civic Center

P1

V1

P3

P2

V2

P4

P5

P6

V3

City of St. Cloud Wayfinding System St. Cloud, FL 16DATE OF ISSUE

REVISION

06/20/2024

#1 - 06/10/2025

A GAI Consultants, Inc. Service Group

618 E. South Street Suite 700 Orlando, Florida 32801 T 407.423.8398 gaiconsultants.com/communitysolutions

Scale: 1/2” = 1’ Sign Type B - Large Vehicular Sign

P4

P3

P2

V1

V2

P6

V2

V2

V1

V1

P1

P5

P1

For copy and arrow

For copy and arrow

For copy and arrow

SEE PAGE 34

FOR VINYL

OVERLAY DETAILS

Aquatics Ctr

Civic Center

2'-8"

10 3/4"

1'-5 1/2"

Front View

9 1/4"

6" 4 1/2"

2 3/4"

4'-2"

4'-2 1/2"

5'-6"

5"

4'-2"

8'-0"

City of St. Cloud Wayfinding System St. Cloud, FL 17DATE OF ISSUE

REVISION

06/20/2024

#1 - 06/10/2025

A GAI Consultants, Inc. Service Group

618 E. South Street Suite 700 Orlando, Florida 32801 T 407.423.8398 gaiconsultants.com/communitysolutions

Scale: 1/2” = 1’ Sign Type B - Large Vehicular Sign

SIGN TYPE B

LARGE VEHICULAR SIGN

Fabrication Details:

1 1/4” aluminum backer panel with routed out custom graphics painted with Matthews automotive grade paint and UV and anti-graffiti protective clear coat.

2 Custom aluminum bracket to mechanically attach the sign face to the sign pole.

3 1/8” front aluminum individual destination panels painted with Matthews automotive grade paint with retro-reflective vinyl and background color overlay.

4 Custom aluminum brackets to attach front panel to backer panel.

5 1/8” logo panel attached to backer panel using VHB tape and dp805.

6 5” capped aluminum pole with decorative base cover painted with Matthews automotive grade paint and UV and anti-graffiti protective clear coat.

7 Decorative base cover.

8 Sign face single sided painted background color and graphics.

Foundation per Florida and City Building Code requirements

Downtown

Aquatics Ctr Civic Center

Front View Side View

DISTRICT NAME

City Hall Downtown

Aquatics Ctr Civic Center

Detail - Sign Face scale: 1”=1’

8"

4"

4" 4 1/4"

4 3/4"

9" 5 1/2"

2 1/4"

4 1/2"

4 3/4"

4"

5 1/2" 1'-0"

4" 4"

11"

6"

3 1/2"

9"

7 1/2"

3/4" 10 3/4" 3/4"

2"

1'-0" 1'-0" 1'-0"

2"

Vector logo to be provided by Designer or Client

P1

V1

P3

P2

V2

P4

P5

P6

V3

DISTRICT NAME

Public Parking

City Hall Downtown

Aquatics Ctr Civic Center

DISTRICT NAME

City Hall Aquatics Ctr

Civic Center

City of St. Cloud Wayfinding System St. Cloud, FL 18DATE OF ISSUE

REVISION

06/20/2024

#1 - 06/10/2025

A GAI Consultants, Inc. Service Group

618 E. South Street Suite 700 Orlando, Florida 32801 T 407.423.8398 gaiconsultants.com/communitysolutions

Scale: 1/2” = 1’ Sign Type C - Small Vehicular Sign

P4

P3

P2

V1

V1

V2

V2

V2

V1

V1

P1

P5

P1

For copy and arrow

For copy and arrow

For copy and arrow

For copy and arrow

SEE PAGE 34

FOR VINYL

Downtown

Aquatics Ctr Civic Center

Front View

6 1/2"

4 3/4"

7 1/2"

1'-10 3/4"

2 1/4"

1'-0"

3'-0"

3'-11"

3'-7 3/4"

5"

8'-0"

Side View

City of St. Cloud Wayfinding System St. Cloud, FL 19Scale: 1/2” = 1’

DATE OF ISSUE

REVISION

06/20/2024

#1 - 06/10/2025

A GAI Consultants, Inc. Service Group

618 E. South Street Suite 700 Orlando, Florida 32801 T 407.423.8398 gaiconsultants.com/communitysolutions

Sign Type C - Small Vehicular Sign

SIGN TYPE C

SMALL VEHICULAR SIGN

Fabrication Details:

1 1/4” aluminum backer panel with routed out custom graphics painted with Matthews automotive grade paint and UV and anti-graffiti protective clear coat.

2 Custom aluminum bracket to mechanically attach the sign face to the sign pole.

3 1/8” front aluminum individual destination panels painted with Matthews automotive grade paint with retro-reflective vinyl and background color overlay.

4 Custom aluminum brackets to attach front panel to backer panel.

5 1/8” logo panel attached to backer panel using VHB tape and dp805.

6 5” capped aluminum pole with decorative base cover painted with Matthews automotive grade paint and UV and anti-graffiti protective clear coat.

7 Decorative base cover.

8 Sign face single sided painted background color and graphics.

Foundation per Florida and City Building Code requirements

Parking

Public Parking

Detail - Sign Face scale: 1”=1’

Front View Side View

7"

6 1/2"

4 3/4"

5 3/4"6"5 3/4"

4" 2" 4"

4 1/2"

2'-1"

7"

4 3/4"

4 3/4"

4"

2"

4"

3"

4 1/2"

EQEQ EQ EQ

P1

V1

P3

P2

V2

P4

P5

P6

V3

DISTRICT NAME

Public Parking

City Hall Downtown

Aquatics Ctr Civic Center

DISTRICT NAME

City Hall Aquatics Ctr

Civic Center

City of St. Cloud Wayfinding System St. Cloud, FL 20Scale: 1/2” = 1’

DATE OF ISSUE

REVISION

06/20/2024

#1 - 06/10/2025

A GAI Consultants, Inc. Service Group

618 E. South Street Suite 700 Orlando, Florida 32801 T 407.423.8398 gaiconsultants.com/communitysolutions

Sign Type D - Parking Directional

P4

P3

P2

V1

V2

V1

V1

V1

P5

V3

SEE PAGE 34

FOR VINYL

Side View

Parking

9"

4 3/4"

2'-1"

1 3/4"

6" R

3'-4 1/2"

5'-7"

4"

1'-5 1/2"

1'-9 3/4"

Front View

City of St. Cloud Wayfinding System St. Cloud, FL 21Scale: 1/2” = 1’

DATE OF ISSUE

REVISION

06/20/2024

#1 - 06/10/2025

A GAI Consultants, Inc. Service Group

618 E. South Street Suite 700 Orlando, Florida 32801 T 407.423.8398 gaiconsultants.com/communitysolutions

Sign Type D - Parking Directional

SIGN TYPE D

PARKING DIRECTIONAL SIGN

Fabrication Details:

1 1/4” aluminum backer panel with routed out custom graphics painted with Matthews automotive grade paint and UV and anti-graffiti protective clear coat.

2 Custom aluminum bracket to mechanically attach the sign face to the sign pole.

3 1/8” front aluminum individual destination panels painted with Matthews automotive grade paint with retro-reflective vinyl and background color overlay attached to backer panel using VHB tape and dp805.

4 1/8” symbol panel attached to backer panel using VHB tape and dp805.

5 4” capped aluminum pole with decorative base cover painted with Matthews automotive grade paint and UV and anti-graffiti protective clear coat.

6 Decorative base cover.

7 Sign face single or double sided (depending on location) painted background color and graphics.

Foundation per Florida and City Building Code requirements

DOWNTOWN ENTERTAINMENT DISTRICT

STREET NAME

DOW

NTOW

N ENTERTAINM

ENT DISTRICT

DOWNTOWN ENTERTAINMENT DISTRICT

STREET NAME

20” x 29” District

Map

20” x 29” District

Map

Destination Destination Destination

Destination Destination Destination

Destination Destination Destination

Detail - Sign Face scale: 1”=1’

Front View Side View

53 3/4"

4 1/2"

4 1/2"

8 5/8"

1/4"

2 5/8"

8 3/4"

1 1/4" 3/4"

3 3/4"

8 3/8"

19 1/4"

1"

24"

2"

1"

1 5/8" 1 1/8"

5/8"

8 1/4" 8 1/4"8 1/4"

2"

1 1/2"

25"

7 1/2"

2 1/8"

29"

29"

20"

Destination Destination Destination

Destination Destination Destination

Destination Destination Destination

DISTRICT NAME

Destination

STREET NAME

STREET NAME

Destination Destination DestinationDestination Destination

DOWNTOWN ENTERTAINMENT DISTRICT

DOWNTOWN ENTERTAINMENT DISTRICT

STREET NAME

13TH STREET / US HIGHWAY 192

13TH STREET / US HIGHWAY 192 13TH STREET / US HIGHWAY 192

12TH STREET12TH STREET 12TH STREET

11TH STREET 11TH STREET11TH STREET

10TH STREET10TH STREET 10TH STREET

9TH STREET9TH STREET 9TH STREET

MA

SSA

CH

USE

TTS

AV

ENU

E

KE

NTU

CKY

AV

ENU

E

KE

NTU

CKY

AV

ENU

E

NEW

YO

RK

AVE

NU

E

NEW

YO

RK

AVE

NU

E

PEN

NSY

LVA

NIA

AV

ENU

E

PEN

NSY

LVA

NIA

AV

ENU

E

FLO

RID

A A

VEN

UE

FLO

RID

A A

VEN

UE

OH

IO A

VEN

UE

MA

SSA

CH

USE

TTS

AV

ENU

E

8TH STREET 8TH STREET 8TH STREET

58 25

73 80

9 24

Handyman Hardware Old Fashion Cigar Southern Roots Antiques Oro D’Italia Sincerely Yours

The Pink Paisley Boutique Gun Store

Solana’s Handmade Cake Pasteries & More

Chime & Time Clock Repair Blissology

Kuppa Thyme Tea Room Phyre Saloon & Steakhouse Crust & Crumb Social House Sweet Spot Snoballs

Chimento’s Spaghetti House Loading Gastrobrunch Garage Bar Island Cloud Grill Granny's Southern Smokehouse Breeze Madilynns Craft Coffee Shop

Nutrition Zone Savvy Sweets Bakery Fortuna Bakery & Cafe The Black Squirrel Bookstore & Speakeasy

10th Street Produce and Deli

Lafontaine French Macarons LLC

Blush Boutique and Salon The Color Loft Rayzor Edge Soul 2 Sole Massage Salon Emvy

Creative Printing Services Lewis and Massey. PA State Farm Insurance Snow Construction Arnco Construction Godwin Realty Group Pro Auto Detailing 3 Lil Birds Tattoo Gallery Andy’s Auto Service LLC Cloud Care Medicine Family Dentistry- James Chen Family Dentistry of St. Cloud Fisk Funeral Home Elite Metro Hemphill Accounting Services Homepride Group at EXP Realty Joe's Auto Services Center Inc Keystone Residential Group Kisselback Insurance Agency

Precision Hearing Aids

Insurance Office of America

Gio Meza…