D040-M1_DR001 Precip Stick.pdf
PDF 28 KB Posted
- Attached to
- Spare Precipitation Measurement Sticks for the National Logistics Support Center in Grandview, MO
- Solicitation number
- 142082-26-0102
About this file
This is an engineering drawing specification for a Measuring Stick used in rain gauges, issued by the National Weather Service, National Oceanic & Atmospheric Administration, U.S. Department of Commerce.
The measuring stick shall be manufactured from plastic thermosetting phenolic high-pressure laminate (NEMA Grade X) in black color, sourced from Norplex/Oak in Lacrosse, Wisconsin or equivalent. The stick measures 25.00 inches ±0.06 inches in length with specific dimensional requirements including width of 0.56 ±0.03 inches and thickness of 0.093 inches. Graduations and lettering must be imprinted with permanent, waterproof, hard white ink or paint directly onto the measuring surface. The stick shall be finished using 200-grit or finer abrasive on both sides to remove shiny finish and achieve a wettable measuring surface. Critical workmanship standards require the lower end be trimmed square and even, with warpage not exceeding 0.15 inch when laid flat in any direction. Accuracy specifications limit scale error to 0.04 inches from the measuring end to any index mark and between any two index marks greater than 2 inches apart. The sticks shall be packed in cartons containing ten units each, separated by paper sheets with snug-fitting packaging to prevent damage. Drawing number D040-M1-DR001 was last revised on 12/17/04, with the metric rule removed from the back as of 8/12/04.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| PHOTO_NLSC_CLS View Precip Stick 6660-00-909-0331.jpg | JPG image | |
| Photo of Precip Stick 0.625 Inch width.jpeg | JPEG file | |
| 1305M226Q0194.pdf | ||
| Shipping Instructions.pdf |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
REVISIONS
APP'DDATEDESCRIPTIONLTRZONE
2 PLACES DECIMALS ±.02
3 PLACES DECIMALS ±.005
TOLERANCES, ANGLES, ±.5°
DIMENSIONS ARE IN INCHES
UNLESS OTHERWISE SPECIFIED:
FILESHEETSCALE
D
DRAWING NO.DATESIZE
DESIGN
APPROVED
CHECKED
PREPARED
SILVER SPRING, MD. 20910
ENGINEERING DIVISION
LIST OF MATERIAL
NATIONAL WEATHER SERVICE
NATIONAL OCEANIC & ATMOSPHERIC ADMINISTRATION
U.S. DEPARTMENT OF COMMERCE
U .S
.DEPARTMEN
ECREMMOCFOT
OSPHERI C
ADMI NI STRAT
IONNA
T
IO
NA
L
OC
EA
NI
C AND
ATM
FIND
NO. DES
ELEC REF NOMENCLATURE
OR DESCRIPTION
QTY
REQD
PART OR
IDENTIFYING
DWG
SIZE
CODE
IDENT
SPECIFICATION
OR MATERIAL
MEASURING STICK,
RAIN GAUGE
R.E.B. 03/93
1 OF 1 D040-M1
D040-M1-DR001
NOTES:
1. MATERIAL:
2. GRADUATIONS:
3. WORKMANSHIP:
4. PACKING:
5. DRAWING STANDARD:
A MATERIAL CHANGED, ETC. 8/86
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
2.10
2.30
2.20
6. FINISH:
PLASTIC, THERMOSETTING, PHENOLIC,
HIGH PRESSURE LAMINATE, NEMA GRADE X, COLOR
BLACK. STOCK SHALL BE FLAT AND UNWARPED.
NORPLEX/OAK, LACROSSE, WI 54602
(608) 784-6070 OR EQUAL.
MEASURING STICK WITH PERMANENT , WATERPROOF,
BE AS SHOWN AND SHALL BE IMPRINTED ONTO THE
TOLERANT TO FLEXING OF THE STICK WITHOUT
HARD, WHITE, INK OR PAINT. THE MARKINGS SHALL BE
NUMERALS, GRADUATIONS, AND LETTERING SHALL
THE LOWER END OF THE STICK SHALL BE TRIMMED
STICK SHALL BE FREE FROM DEFECTS THAT COULD
SQUARE AND EVEN. THE STICK WHEN LAID ON A
FLAT SURFACE WITH ITS WIDTH FACE (.56) DOWN
SHALL NOT EXHIBIT WARPAGE GREATER THAN 0.15
SHALL NOT BE GREATER THAN 0.15 INCH.
THICKNESS FACE ( .093 ) DOWN THE WARPAGE
INCH AT ANY POINT, AND WHEN LAID WITH ITS
IMPAIR ITS ACCURACY OR SERVICEABILITY.
A STRAIGHT AND UNWARPED CONDITION.
DAMAGE TO THE STICKS AND TO KEEP THEM IN
OF STICKS PACKED; THE PURPOSE BEING TO PREVENT
AS TO PROVIDE A SNUG FIT FOR THE EXACT NUMBER
BE OF SUITABLE MATERIAL AND OF SUCH DIMENSIONS
IN CARTONS CONTAINING TEN (10) EACH. THE CARTONS SHALL
THE STICKS SHALL BE PACKED BETWEEN PAPER SHEETS
INTERPRET DRAWING IN A/W DOD-STD-100
STICK SHALL BE FINISHED USING 200 GRIT OR FINER
ABRASIVE ON BOTH SIDES TO REMOVE SHINY FINISH.
MEASURING SURFACES SHALL BE WETABLE
NO
AA
WE
AT
HE
R
NA
TI
ON
AL
SE
RV
IC
E
IN
CH
ES
RA
IN
25.00 ±.06
24.00
1.00 TYP.
0.50 TYP.
0.10 TYP.
ALL
GRADUATIONS
.030
.020WIDE
SEE NOTES 2 & 5
.030
.19 DIA
-A-
.03 R
A .010
DRAWING NO. CHANGED FROMB 10/86D040-DR005 TO
D040-M1-DR001
NEXT
ASSY
QTY
REQDAPPLICATION
USED ON NEXT ASSY
1D040-DR001
.56 ±.03
.25 ±.03 .44 ±.03
.12 ±.03
TYP.
TYP.
TYP.
TYP.
.18 ±.03
.03R
.09 TYP.
.28
0.38
.093 STOCK
12/17/04
REMOVE METRIC RULE FROM BACKC 8/12/04
David Desrosiers
TYP.
FLAKING OR CRACKING.
MARKS GREATER THAN 2 INCHES APART SHALL NOT EXCEED
STICK TO ANY INDEX MARK AND FOR ANY TWO INDEX
THE SCALE ERROR FROM THE MEASURING END OF THE
7. ACCURACY:
0.04 INCHES.
ADD NOTE 7: ACCURACY AND REVISE NOTE 2.D 12/17/04
Model
File details come from the government source that posted it. Updated .