Combined_Synopsis_Solicitation_Membrane_Test_Skid_July_25.pdf

Solicitation Number: 140R8125Q0209

Combined Synopsis/Solicitation Template eFile – C05

(04/2023)

COMBINED SYNOPSIS/SOLICITATION TEMPLATE (FAR 12.603)

This is a combined synopsis/solicitation for commercial products or services prepared in accordance with the format in subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; quotes are being requested and a written solicitation will not be issued. Solicitation number

140R8125Q0209 is issued as a request for quotation (RFQ). The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition

Circular 2025-04. It is the responsibility of the contractor to be familiar with the applicable clauses and provisions. They may be accessed in full text at the following websites: https:/www.acquisition.gov/far/ and https://www.acquisition.gov/diar. The associated North American Industrial Classification System (NAICS) code for this procurement is 334516 with an associated small business size standard of 1000.

CLIN Description Qty Unit of

Measure

Unit

Price

Total

Price

00010 Automated Hybrid Test Skid, 316 ss 1 Each

00020 1812 Spiral Wound Housing, 316 ss 2 Each

00030 SEPA CF Flat Sheet Membrane

Housing, 316

2 Each

00040 Hydraulic Hand Pump for SEPA Cell

Holder

1 Each

00050 SEPA Acrylic Flat Sheet Membrane

Housing

2 Each

00060 Miscellaneous Accessories Including

Shim

1 Each

00070 Delivery/Shipping 1 Each

00080 Installation and Training 1 Each

Total price shall be inclusive of all applicable fees and taxes. The required delivery date is not later than 30 September 2025. Inspection and acceptance will be performed by the

Government at destination. F.O.B. Destination at:

http://www.acquisition.gov/far/ http://www.acquisition.gov/diar eFile – C05

(04/2023)

Solicitation Number: 140R8125Q0209

Bureau of Reclamation-DO

Building 67, Entrance E3, Room 165

6th Avenue & Kipling Street

Denver Federal Center

Denver CO 80225-0007

The provision at 52.212-1, Instructions to Offerors – Commercial Products and Commercial Services, applies to this acquisition. The provision at 52.212-1, Instructions to Offerors – Commercial Products and Commercial Services, applies to this acquisition. Addendum to 52.212-1 substitutes the term “quote” where the term “offer” appears in the provision.Offeror must provide quote on company letterhead with contact information which documents all salient characteristics of the products being offered. Quote must include an automated membrane test unit capable of testing microfiltration, ultrafiltration, nanofiltration and reverse osmosis at the bench-scale to inform full-scale design parameters for drinking water and water reuse applications.

--Addendum to 52.212-1--

Substitutes the term “quote” where the term “offer” appears in the provision.

Offeror must provide quote on company letterhead with contact information which documents all salient characteristics of the product being offered. Quotes submitted shall include the warranty in full text. Quotes without the inclusion of the full text warranty will not be accepted. Quotes that do not meet the specifications listed in the line-item description will not be accepted.

52.252-1 Solicitation Provisions Incorporated by Reference

This solicitation incorporates one or more solicitation provisions by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. The offeror is cautioned that the listed provisions may include blocks that must be completed by the offeror and submitted with its quotation or offer. In lieu of submitting the full text of those provisions, the offeror may identify the provision by paragraph identifier and provide the appropriate information with its quotation or offer. Also, the full text of a solicitation provision may be accessed electronically at this/these address(es):

https:/www.acquisition.gov/far/ https://www.acquisition.gov/diar

52.204-7 System for Award Management

52.204-16 Commercial and Government Entity Code Reporting

52.252-5 Authorized Deviations in Provisions

DIAR 1452.215-71 Use and Disclosure of Proposal Information--Department of the Interior (APR 1984)

--End of Addendum to 52.212-1--

The provision at 52.212-2, Evaluation – Commercial Products and Commercial Services, applies to this acquisition. The specific evaluation criteria to be included in paragraph (a) of that provision is as follows: Lowest

Price.

(End of Provision)

52.212-3 Offeror Representations and Certifications Commercial Products and Commercial Services

(MAY 2024) (DEVIATION FEB 2025), must be completed and be active online at http://www.sam.gov.

Prospective contractor is advised to ensure that the NAICS code identified for this procurement is contained in its online representations and certifications in the System for Award Management registry.

(04/2023)

--Addendum to 52.212-3—

52.204-24 REPRESENTATION REGARDING CERTAIN TELECOMMUNICATIONS

AND VIDEO SURVEILLANCE SERVICES OR EQUIPMENT (NOV 2021), the offeror must indicate their 889 representation on SAM.gov.

(End of provision)

---End of Addendum to 52.212-3---

The clause at 52.212-4, Contract Terms and Conditions – Commercial Products and

Commercial Services, applies to this acquisition along with an addenda that includes the following clauses applicable to this procurement:

--Addendum to 52.212-4--

52.252-2 Clauses Incorporated by Reference

This contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at this/these address(es):

https:/www.acquisition.gov/far/

52.204-13 System for Award Management Maintenance

52.204-18 Commercial and Government Entity Code Maintenance

52.252-6 Authorized Deviations in Clauses

DOI-AAAP-0028 Electronic Invoicing and Payment Requirements - Invoice Processing

Platform (IPP) (FEB 2021)

Payment requests must be submitted electronically through the U. S. Department of the

Treasury's Invoice Processing Platform System (IPP).

"Payment request" means any request for contract financing payment or invoice payment by the

Contractor. To constitute a proper invoice, the payment request must comply with the requirements identified in the applicable Prompt Payment clause included in the contract, or the clause 52.212-4 Contract Terms and Conditions - Commercial Items included in commercial item contracts. The IPP website address is: https://www.ipp.gov.

Under this contract, the following documents are required to be submitted as an attachment to the

IPP invoice:

The Contractor shall attach a hard copy of their IPP invoice to their IPP submission.

Failure to attach a hard copy invoice to IPP may result in rejection of your payment request.

The Contractor must use the IPP website to register access and use IPP for submitting requests for payment. The Contractor Government Business Point of Contact (as listed in

SAM) will receive enrollment instructions via email from the Federal Reserve Bank of

St. Louis (FRBSTL) within 3 - 5 business days of the contract award date. Contractor assistance with enrollment can be obtained by contacting the IPP Production Helpdesk via email IPPCustomerSupport@fiscal.treasury.gov or phone (866) 973-3131.

If the Contractor is unable to comply with the requirement to use IPP for submitting invoices for payment, the Contractor must submit a waiver request in writing to the

Contracting Officer with its proposal or quotation.

(End of local clause)

--End of Addendum to 52.212-4—

The following select clauses at 52.212-5 Contract Terms and Conditions Required to

Implement Statutes or Executive Orders—Commercial Products and Commercial

Services (Jan 2025) (DEVIATION FEB 2025) apply to this acquisition:

(a) The Contractor shall comply with the following Federal Acquisition Regulation

(FAR) clauses, which are incorporated in this contract by reference, to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services:

(1) 52.203-19, Prohibition on Requiring Certain Internal Confidentiality Agreements or

Statements (Jan 2017) (section 743 of Division E, Title VII, of the Consolidated and

Further Continuing Appropriations Act, 2015 (Pub. L. 113-235) and its successor provisions in subsequent appropriations acts (and as extended in continuing resolutions)).

(2) 52.204-23, Prohibition on Contracting for Hardware, Software, and Services

Developed or Provided by Kaspersky Lab Covered Entities (Dec 2023) (Section 1634 of

Pub. L. 115-91).

(3) 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video

Surveillance Services or Equipment. (Nov 2021) (Section 889(a)(1)(A) of Pub. L. 115-

232).

(4) 52.209-10, Prohibition on Contracting with Inverted Domestic Corporations (Nov

2015).

(5) 52.232-40, Providing Accelerated Payments to Small Business Subcontractors (Mar

2023) ( 31 U.S.C. 3903 and 10 U.S.C. 3801).

(6) 52.233-3, Protest After Award (Aug 1996) (31 U.S.C. 3553).

(7) 52.233-4, Applicable Law for Breach of Contract Claim (Oct 2004) (Public Laws

108-77 and 108-78 ( 19 U.S.C. 3805 note)).

b) The Contractor shall comply with the FAR clauses in this paragraph (b) that the Contracting

Officer has indicated as being incorporated in this contract by reference to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services:

X (9) 52.204-27, Prohibition on a ByteDance Covered Application (Jun 2023) (Section 102 of

Division R of Pub. L. 117-328).

X (10) 52.204-28, Federal Acquisition Supply Chain Security Act Orders—Federal Supply

Schedules, Governmentwide Acquisition Contracts, and Multi-Agency Contracts. (Dec 2023) (

Pub. L. 115–390, title II).

X (18)(i) 52.219-6, Notice of Total Small Business Set-Aside (Nov 2020) (15 U.S.C. 644).

X (i) 52.219-28, Post award Small Business Program Re-representation (Jan 2025) (15 U.S.C.

632(a)(2)).

X (31) 52.222-3, Convict Labor (Jun 2003) (E.O.11755).

X (32) 52.222-19, Child Labor—Cooperation with Authorities and Remedies (Jan 2025)( E.O.

13126).

X (36) (i) 52.222-36, Equal Opportunity for Workers with Disabilities (Jun 2020) ( 29 U.S.C.

793).

X (39)(i) 52.222-50, Combating Trafficking in Persons (Nov 2021) (22 U.S.C. chapter 78 and

E.O. 13627).

X (46) 52.223-23, Sustainable Products and Services (May 2024) (DEVIATION FEB 2025) ( 7

U.S.C. 8102, 42 U.S.C. 6962, 42 U.S.C. 8259b, and 42 U.S.C. 7671l).

X (48)(i) 52.225-1, Buy American-Supplies (Oct 2022) (41 U.S.C. chapter 83).

X (51) 52.225-13, Restrictions on Certain Foreign Purchases (Feb 2021) (E.O.’s, proclamations, and statutes administered by the Office of Foreign Assets Control of the Department of the

Treasury).

X (55) 52.226-8, Encouraging Contractor Policies to Ban Text Messaging While Driving (May

2024) ( E.O. 13513).

X (59) 52.232-33, Payment by Electronic Funds Transfer-System for Award Management

(Oct2018) ( 31 U.S.C. 3332).

X (63) 52.240-1, Prohibition on Unmanned Aircraft Systems Manufactured or Assembled by

American Security Drone Act-Covered Foreign Entities (Nov 2024) (Sections 1821-1826, Pub.

L. 118-31, 41 U.S.C. 3901 note prec.).

(c) The Contractor shall comply with the FAR clauses in this paragraph (c), applicable to commercial services, that the Contracting Officer has indicated as being incorporated in this contract by reference to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services:

(d) Comptroller General Examination of Record. The Contractor shall comply with the provisions of this paragraph (d) if this contract was awarded using other than sealed bid, is in excess of the simplified acquisition threshold, as defined in FAR 2.101, on the date of award of this contract, and does not contain the clause at 52.215-2, Audit and Records-Negotiation.

(1) The Comptroller General of the United States, or an authorized representative of the

Comptroller General, shall have access to and right to examine any of the Contractor’s directly pertinent records involving transactions related to this contract.

(2) The Contractor shall make available at its offices at all reasonable times the records, materials, and other evidence for examination, audit, or reproduction, until 3 years after final payment under this contract or for any shorter period specified in FAR subpart 4.7, Contractor

Records Retention, of the other clauses of this contract. If this contract is completely or partially terminated, the records relating to the work terminated shall be made available for 3 years after any resulting final termination settlement. Records relating to appeals under the disputes clause or to litigation or the settlement of claims arising under or relating to this contract shall be made available until such appeals, litigation, or claims are finally resolved.

(3) As used in this clause, records include books, documents, accounting procedures and practices, and other data, regardless of type and regardless of form. This does not require the

Contractor to create or maintain any record that the Contractor does not maintain in the ordinary course of business or pursuant to a provision of law.

(e)

(1) Notwithstanding the requirements of the clauses in paragraphs (a), (b), (c), and (d) of this clause, the Contractor is not required to flow down any FAR clause, other than those in this paragraph (e)(1), in a subcontract for commercial products or commercial services. Unless otherwise indicated below, the extent of the flow down shall be as required by the clause-

(i) 52.203-13, Contractor Code of Business Ethics and Conduct (Nov 2021) (41 U.S.C. 3509).

(ii) 52.203-17, Contractor Employee Whistleblower Rights (Nov 2023) ( 41 U.S.C. 4712).

(iii) 52.203-19, Prohibition on Requiring Certain Internal Confidentiality Agreements or

Statements (Jan 2017) (section 743 of Division E, Title VII, of the Consolidated and Further

Continuing Appropriations Act, 2015 (Pub. L. 113-235) and its successor provisions in subsequent appropriations acts (and as extended in continuing resolutions)).

(iv) 52.204-23, Prohibition on Contracting for Hardware, Software, and Services Developed or

Provided by Kaspersky Lab Covered Entities (Dec 2023) (Section 1634 of Pub. L. 115-91).

(v) 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video

Surveillance Services or Equipment. (Nov 2021) (Section 889(a)(1)(A) of Pub. L. 115-232).

(vi) 52.204-27, Prohibition on a ByteDance Covered Application (Jun 2023) (Section 102 of

Division R of Pub. L. 117-328).

(vii)

(A) 52.204–30, Federal Acquisition Supply Chain Security Act Orders—Prohibition.

(Dec 2023) ( Pub. L. 115–390, title II).

(B) Alternate I (Dec 2023) of 52.204–30.

(viii) 52.219-8, Utilization of Small Business Concerns (Jan 2025) ( 15 U.S.C. 637(d)(2) and (3)), in all subcontracts that offer further subcontracting opportunities. If the subcontract (except subcontracts to small business concerns) exceeds the applicable threshold specified in FAR 19.702(a) on the date of subcontract award, the subcontractor must include 52.219-8 in lower tier subcontracts that offer subcontracting opportunities.

(ix) [Reserved]

(x) [Reserved]

(xi) 52.222-35, Equal Opportunity for Veterans (Jun 2020) (38 U.S.C. 4212).

(xii) 52.222-36, Equal Opportunity for Workers with Disabilities (Jun 2020) (29 U.S.C.

793).

(xiii) 52.222-37, Employment Reports on Veterans (Jun 2020) (38 U.S.C. 4212).

(xiv) 52.222-40, Notification of Employee Rights Under the National Labor Relations

Act (Dec 2010) (E.O. 13496). Flow down required in accordance with paragraph (f) of

FAR clause 52.222-40.

(xv) 52.222-41, Service Contract Labor Standards (Aug 2018) ( 41 U.S.C. chapter 67).

(xvi)

(A) 52.222-50, Combating Trafficking in Persons (Nov 2021) (22 U.S.C. chapter 78 and

E.O 13627).

(B) Alternate I (Mar 2015) of 52.222-50 (22 U.S.C. chapter 78 and E.O. 13627).

(xvii) 52.222-51, Exemption from Application of the Service Contract Labor Standards to Contracts for Maintenance, Calibration, or Repair of Certain Equipment-Requirements

(May 2014) (41 U.S.C. chapter 67).

(xviii) 52.222-53, Exemption from Application of the Service Contract Labor Standards to Contracts for Certain Services-Requirements (May 2014) (41 U.S.C. chapter 67).

(xix) 52.222-54, Employment Eligibility Verification (Jan 2025) ( E.O. 12989).

(xx) 52.222-55, Minimum Wages for Contractor Workers Under Executive Order 14026

(Jan 2022).

(xxi) 52.222-62, Paid Sick Leave Under Executive Order 13706 (Jan 2022) (E.O. 13706).

(xxii)

(A) 52.224-3, Privacy Training (Jan 2017) ( 5 U.S.C. 552a).

(B) Alternate I (Jan 2017) of 52.224-3.

(xxiii) 52.225-26, Contractors Performing Private Security Functions Outside the United States

(Oct 2016) (Section 862, as amended, of the National Defense Authorization Act for Fiscal Year

2008; 10 U.S.C. Subtitle A, Part V, Subpart G Note).

(xxiv) 52.226-6, Promoting Excess Food Donation to Nonprofit Organizations (Jun 2020) (42

U.S.C. 1792). Flow down required in accordance with paragraph (e) of FAR clause 52.226-6.

(xxv) 52.232-40, Providing Accelerated Payments to Small Business Subcontractors (Mar 2023)

( 31 U.S.C. 3903 and 10 U.S.C. 3801). Flow down required in accordance with paragraph (c) of

52.232-40.

(xxvi) 52.240-1, Prohibition on Unmanned Aircraft Systems Manufactured or Assembled by

American Security Drone Act-Covered Foreign Entities (Nov 2024) (Sections 1821-1826, Pub.

L. 118-31, 41 U.S.C. 3901 note prec.).

(xxvii) 52.247-64, Preference for Privately Owned U.S.-Flag Commercial Vessels (Nov 2021) (

46 U.S.C. 55305 and 10 U.S.C. 2631). Flow down required in accordance with paragraph (d) of

FAR clause 52.247-64.

(2) While not required, the Contractor may include in its subcontracts for commercial products and commercial services a minimal number of additional clauses necessary to satisfy its contractual obligations.

(End of clause)

NOTICE:

System updates may lag policy updates. The System for Award Management (SAM) may continue to require entities to complete representations based on provisions that are not included in agency solicitations, including 52.223-22, Public Disclosure of Greenhouse Gas

Emissions and Reduction Goals—Representation, and paragraph (t) of 52.212-3, Offeror

Representations and Certifications—Commercial Products and Commercial Services.

Agencies will not consider or use these representations. Entities are not required to, nor are they able to, update their entity registration to remove these representations in SAM.

Written, signed quote on company letterhead with contact information are due no later than Monday, July 28th at 12pm Eastern Time by email to ksingleton@usbr.gov . For information regarding this RFQ, please contact Keith Singleton at ksingleton@usbr.gov.

Attachment: 1) Statement of Work mailto:ksingleton@usbr.gov

STATEMENT OF WORK

Title: Bench Scale Membrane Treatment Unit

Requestor: Miguel Arias-Paic, mariaspaic@usbr.gov

1.0 Background

Reclamation’s Water Treatment Laboratory (WTL) is purchasing an automated membrane test unit capable of testing microfiltration, ultrafiltration, nanofiltration and reverse osmosis at the bench-scale to inform full-scale design parameters for drinking water and water reuse applications. The WTL does not have this current capability.

2.0 Scope

The scope is to acquire an automated bench scale membrane test unit.

Equipment includes the membrane skid and necessary accessories, including feed tank, human machine interface, temperature control, flow control, and pressure control, instrumentation, membrane housings, modulating membrane recovery control valves and mobile stainless-steel cart where the entire unit is contained, all to conduct water treatment testing.

3.0 Objectives

An automated bench scale membrane test unit capable of testing nanofiltration and reverse osmosis at the bench-scale in flat sheet and spiral wound configurations and micro and ultrafiltration membrane filtration if it fits into the 1812 housing is required. Delivery, assembly, and onsite training at TSC laboratories are included in equipment acquisition.

4.0 Tasks

A bench scale membrane test unit and accessories to meet the technical specifications as follows:

1. Automated Hybrid Test Skid and accessories with the following salient characteristics (Sterlitech or equal):

a. Automated Hybrid Test Skid with 316 stainless steel materials contacting water

i. Automated pressure, flow, and feed water recovery control

ii. Feed flow rate up to 11.7 liters per minute (LPM)

iii. Maximum system operating pressure 1000 pounds per square inch

(psi)

iv. Electrical: 110/230V, 50/60Hz, 1 Phase

v. Capability, including all required mounting and piping hardware, to test microfiltration, ultrafiltration, nanofiltration and reverse osmosis membranes in spiral wound (1812 element) or cross flow flat sheet

(SEPA or equal) configurations with solenoid-controlled parallel process lines

vi. Capability, including all required hardware, to optionally operate two cross flow membrane cells in series (SEPA or equal)

vii. Pump: Diaphragm Pump with motor (Hydra-Cell with Leeson

Washdown Motor or equal)

viii. Gas Cannister/Compressor pressure delivery greater than 1000 psi

ix. Integrated chiller and heat exchange capable of temperature control -

10 to 20 degrees Celsius for recirculating feed water when the feed tank is operating containing the largest and smallest operational volume

x. Auto shutoff enabled by

1. High pressure

2. Low liquid level

xi. All required instrumentation, hardware, tubing, and controls to enable data collection and download capability for:

1. Conductivity: Feed and flexible location

2. Flow: Feed / Concentrate

3. Feed Water Recovery based on calculated permeate flow

4. Pressure: Feed, concentrate, transmembrane

5. Temperature: Feed and flexible location

6. Permeate Flux

xii. Digital Control Panel operable by ethernet cable (without WiFi connectivity) with capability to preset setpoints or modify during run

xiii. Feed Tank: 20 liters with cover

xiv. Equipment mounted on mobile cart

xv. Spare equipment including:

1. Conductivity sensor, Quantity one (1)

2. Pressure sensor, Quantity one (1)

3. Flow meter, Quantity one (1)

4. Temperature sensor, Quantity one (1)

xvi. One spare actuated valve for each actuated valve present on the skid.

b. Spiral wound 1812 membrane housing, Quantity two (2), with the following characteristics:

i. Material: Stainless Steel 316

ii. Maximum operating pressure: 600 psi

iii. 1/2” tube fittings with female adapters

iv. O-ring material: EPDM

c. Cross flow flat sheet stainless steel membrane housing, Quantity two (2), with the following characteristics (SEPA or equal):

i. 75mil channel depth

ii. 140 cm2 membrane area

iii. Material: Stainless Steel 316

iv. Maximum operating pressure: 1000 psi

v. 3/8” Tube Fitting for Feed Inlet and Outlet

vi. 1/4” tube fitting for Permeate Outlet

vii. O-ring material: EPDM

d. Aluminum cell holder, Quantity two (2), with the following characteristics:

i. Compatible with cross flow stainless steel cell

ii. Maximum operating pressure: 1000 psi

iii. quick release fittings

iv. O-ring material: Buna-N

e. Hydraulic hand pump compatible with Aluminum Cell Holder, Quantity one

(1), including parts to connect to two cross flow cells with single hand pump

f. Cross flow flat sheet acrylic membrane housing, Quantity two (2), with the following characteristics (SEPA or equal):

i. 75 mil channel depth

ii. 140 cm2 membrane area

iii. Material: Acrylic

iv. Maximum operating pressure: 220 psi

v. 3/8” Tube Fitting for Feed Inlet and Outlet

vi. 1/4” tube fitting for Permeate Outlet

vii. O-ring material: EPDM

g. Recovery kit to fully drain automated membrane test system.

h. Steel die template to cut membranes to cross flow membrane housing size, Quantity one (1)

i. Stainless steel shims for cross flow membrane housing cell, including:

i. 2 mil, Quantity one (1)

ii. 3 mil, Quantity one (1)

iii. 4 mil, Quantity one (1)

iv. 5 mil, Quantity one (1)

v. 10 mil, Quantity three (3)

vi. 15 mil, Quantity three (3)

j. One year warranty period from receipt, assembly and training covering defects in material and workmanship when operated in accordance with written instructions for all parts. Material compatibility with liquids is not covered by warranty.

2. Delivery per section 5.0

3. Assembly of automated test skid

4. Training for WTL staff following assembly, minimum two staff days by qualified vendor engineer / technician.

5.0 Delivery

The supplier is responsible for the delivery and assembly of the instrument.

Training by the manufacturer is required for WTL staff.

6.0 Qualifications

Technician / engineer has one year of experience working with vendor supplied units.

6.0 Government-Furnished Property

The Government is furnishing a government-issued computer and compatible gas cylinders as part of this acquisition.

7.0 Security

The Supplier is responsible for ensuring the shipment passes all security requirements. The supplier will need to provide all necessary documentation to pass all security checks.

8.0 Place of Performance

The equipment is to be delivered to:

Grace Scarim

Building 56, Door S-6

Bureau of Reclamation

Denver Federal Center

Denver, CO 80225

9.0 Period of Performance

The system shall be ready to be delivered within 90 days of contract award.

10.0 Photos of bench scale membrane test unit

Sterlitech Automated Hybrid Test Skid

Figure 1. Automated hybrid test skid