CDRL_Drawing_21-58157_Rev_AJ.pdf

PREVIOUS EDITION MAY BE USED.

DD FORM 1423, FEB 2024 Page 1 of 4

UNCLASSIFIED

UNCLASSIFIED

CONTRACT DATA REQUIREMENTS LIST

A. CONTRACT LINE ITEM NO.

B. EXHIBIT

A

C. CATEGORY:

TDP TM OTHER

D. SYSTEM/ITEM

Drawing 21-58157

E. CONTRACT/PR NO.

FD20202600227-01

F. CONTRACTOR

BOEING

1. DATA ITEM NO.

A004

2. TITLE OF DATA ITEM

PRODUCT ENGINEERING DESIGN DATA AND LISTS

3. SUBTITLE

Drawing 21-58157 Rev AJ

4. AUTHORITY (Data Acquisition Document No.)

DI-SESS-81000/T (See block 16)

5. CONTRACT REFERENCE 6. REQUIRING OFFICE

414 GUEAA

7. DD 250 REQ

DD

8. APP CODE

A

9. DIST STATEMENT

REQUIRED

D

10. FREQUENCY

See block 16

11. AS OF DATE

See block 16

12. DATE OF FIRST SUBMISSION

See block 16

13. DATE OF SUBSEQUENT

SUBMISSION

See block 16

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

Draft Final

Reg Repro

16. REMARKS

1. Mark the contract number this drawing was delivered under on the front page of the drawing. If the drawing has an existing contract number, copy that to the new revision of the drawing for historical traceability.

2. Per DoDI 5200.48 CUI markings for unclassified DoD documents will include the acronym “CUI” in the banner and footer of every page of the document. *NOTE: Date of determination is the date the distribution statement is added to the document.

Data submittal shall be marked with the following on the cover page:

Distribution Statement D: Distribution authorized to the Department of Defense and U.S. DoD contractors only CTI & Export Controlled *(date of determination). Other requests for this document must be referred to Minuteman III Program Office, Hill AFB, UT 84056.

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Section 2751 of Title 22, United States Code) or the Export Control Reform Act of 2018 (Chapter 58 Sections 4801-4852 of Title 50, United States Code). Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoD Directive 5230.25 and DoD Instruction 2040.02.

DESTRUCTION NOTICE: For classified documents follow the procedures in DoD 5220.22-M, National Industrial Security Program Operating Manual (NISPOM), Section 5-705, or DoD 5200.1-R, Information Security Program, Chapter 6. For unclassified documents destroy by any method that will prevent disclosure of contents or reconstruction of the document.

Controlled by: DEPARTMENT OF THE AIR FORCE Controlled by: AFNWC/NIMPL CUI Category: Controlled Technical Information/ Export Controlled Distribution/Dissemination Control: Distribution Statement D POC: Jeannea Plagge, jeannea.plagge.1@us.af.mil

3. The applicable issue of any documents cited herein, including their approval dates and dates of any applicable amendments, notices, and revisions, shall be as specified in the contract. This CDRL is applicable to both software and hardware drawings.

4.Engineering Changes to Air Force Drawings.

a. Contractor shall document any changes to existing Air Force Drawings using AFMC Forms 3925, 3926, and 3927 (Engineering Order Forms). Final approval and release of engineering orders shall be a function of the U.S. Government.

b. Delivery of Engineering Orders – Contractor shall submit DRAFT engineering order forms to the Government as they occur. The Government requires 15 working days for review and approval.

Contractor shall incorporate comments and provide corrected copies within 10 working days of receipt.

Draft delivery shall be in PDF format.

c. Instructions for completing engineering orders (AFMC Forms 3925, 3926, & 3927) can be found on the form.

Email electronic copies to the following list:

jeannea.plagge.1@ 1 1 us.af.mil naomi.strickler@ 1 1 us.af.mil khalid.snounou@ 1 us.af.mil nathan.rieske.1@ 1 us.af.mil

15.TOTAL 2 4

17. PRICE GROUP

NSP

18. ESTIMATED

TOTAL PRICE

0.00

DD FORM 1423, FEB 2024 Page 2 of 4

UNCLASSIFIED

UNCLASSIFIED

1. DATA ITEM NO. 2. TITLE OF DATA ITEM 3. SUBTITLE

4. AUTHORITY (Data Acquisition Document No.) 5. CONTRACT REFERENCE 6. REQUIRING OFFICE

7. DD 250 REQ

8. APP CODE

9. DIST STATEMENT

REQUIRED

10. FREQUENCY

11. AS OF DATE

12. DATE OF FIRST SUBMISSION

13. DATE OF SUBSEQUENT

SUBMISSION

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

Draft Final

Reg Repro

16. REMARKS

5. Control Drawings. Contractor shall prepare control drawings for commercial or vendor items IAW

ASME Y14.24.

6. New drawings. For newly created Drawings and Associated Lists, DI-SESS-81000D/T and Technical Data Package Option Selection Worksheet (defined in MIL-STD-31000) are applicable. Tailoring to DID shall be per TDP Option Selection Worksheet (Atch 1).

All newly created Drawings and Associated Lists shall be IAW the following tailored documents: ASME Y14.100-2017 (including Appendices B, C, D, E), ASME Y14.3, ASME Y14.5, and ASME Y14.35.

Tailoring to these documents as indicated on this DD form 1423. The following documents are used in whole: ASME Y14.1, ASME Y14.2, ASME Y14.24, and ASME Y14.34.

9. Tailoring to ASME documents:

ASME Y14.100

(1) (Application Data) para 4.6 – Application Data is required on first sheet of Drawing and Associated List. General use or multi-use notations is allowed.

(2) (Drawing Notes) para 4.27 – Drawing Notes shall be on first sheet of drawing.

ASME Y14.35

(1) (Recreated Datasets) – shall be IAW para 4.4, sub-para 4.4.1

(2) (Recording Revisions) – shall be IAW para 6 Contractor shall maintain revision history in its entirety.

(3) (Revision Letters) – Shall be IAW para 5.2

(4) (Revision Status of Sheets Block) – shall be IAW para 7.5

(5) (Adding or Deleting Sheets) – shall be IAW para 7.6

ASME Y14.5

(Dimensioning and Tolerancing) – shall be IAW para 4.2.2 and shall be decimal inch.

ASME Y14.100 INVOKED APPENDICES

Appendix B – Noncommercial Drawing Practices Appendix B – for para B5 see TDP Option Selection Worksheet Appendix C – Drawing Titles Appendix D – Numbering, Coding, and Identification Appendix E – Makings on Engineering Drawings Appendix E – for para E7 see DD1423 Block 16

15.TOTAL

17. PRICE GROUP

18. ESTIMATED

TOTAL PRICE

DD FORM 1423, FEB 2024 Page 3 of 4

UNCLASSIFIED

UNCLASSIFIED

1. DATA ITEM NO. 2. TITLE OF DATA ITEM 3. SUBTITLE

4. AUTHORITY (Data Acquisition Document No.) 5. CONTRACT REFERENCE 6. REQUIRING OFFICE

7. DD 250 REQ

8. APP CODE

9. DIST STATEMENT

REQUIRED

10. FREQUENCY

11. AS OF DATE

12. DATE OF FIRST SUBMISSION

13. DATE OF SUBSEQUENT

SUBMISSION

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

Draft Final

Reg Repro

16. REMARKS

9. Drawing deliveries:

Draft/preliminary drawings shall be delivered 30 working days prior to the First Article Inspection in PDF format if changes are made during production. The Government shall provide comments to the drawings 10 working days prior to each review/audit. Agreed to comments shall be incorporated into the drawing prior to the next review/audit.

J-size drawings (if applicable) shall be split into frames and submitted as E-size sheets.

Final Delivery: Delivery of the final drawing package shall be made 30 working days after closeout of the First Article Inspection. Final delivery media for Drawings and Associated Lists shall be in PDF format.

Drawings can be submitted as a single file for each drawing (multiple sheets per file) or as a single file for each sheet. Associated lists (specs, PLs, AL, WLs, etc) may be submitted as A-size sheets provided all information and borders for each sheet of the document are formatted to print within an 8 ½ X 11 sheet of paper. If any sheet of the document runs over to another page the file cannot be accepted. Associated Lists shall be submitted as one file for the complete document.

1 Attachment

1. TDP Selection Worksheet

15.TOTAL

17. PRICE GROUP

18. ESTIMATED

TOTAL PRICE

G. PREPARED BY

Naomi Strickler

H. SIGNED ON 20260817 I. APPROVED BY

Michael Loveless

J. SIGNED ON 20260817

STRICKLER.NAO

MI.M.1507327296

Digitally signed by

STRICKLER.NAOMI.M.1507327296

Date: 2026.08.17 07:56:37 -06'00'

LOVELESS.MICHAE

L.ALAN.1519342827

Digitally signed by

LOVELESS.MICHAEL.ALAN.151934

Date: 2026.08.17 07:49:09 -06'00'