B08 Solicitation - Statement of Work - Exterior Painting.pdf

PEVI – 224362, 224363 09 91 10 - 1

EXTERIOR PAINTING AND TRANSPARENT FINISHES

Perry’s Victory and International Peace Memorial

93 Delaware Ave. Put in Bay, Ohio 43456

Paint Exterior of Buildings 50, 80. And 100

PMIS 224362

Paint Exterior of Buildings 60 and 90

PMIS 224363

PROJECT SPECIFICATIONS

NATIONAL PARK SERVICE

April 29th 2020

PEVI – 224362, 224363 09 91 10 - 2

SECTION 09 91 10 - EXTERIOR PAINTING AND TRANSPARENT FINISHES

PART 1 - GENERAL

1.1 SUMMARY

A. This portion of the project represents the painting of all exterior surfaces of two single family homes and three duplex apartments. Many of the painted surfaces show signs of cracking and pealing. The five structures were constructed in 1993, 15 years after lead based paint was outlawed. Lead base paint is not suspect. See the end of this section for a Color Schedule and the Drawings for colors and locations. Samples must be provided in the field for Contracting Officer’s approval prior to removal of the existing paint and prior to the application of any new paint. Allow maximum time for review, do NOT hold to last minute close to arrival at site.

B. This Section includes surface preparation and the application of paint systems on the following exterior substrates:

1. Steel doors

2. Cedar wood trim

3. Cedar wood lapboard sidings.

1.2 SUBMITTALS

A. Product Data: For each type of product indicated, include manufacturer’s printed statement of VOC content.

B. Samples: Provide drawdown for each finish, each color, and for each texture specified, include formula for each combination. See Color Schedule at end of this specification.

C. Product List: Printout of current "MPI Approved Products List" for each product category specified in Part 2, with the proposed product highlighted.

1.3 QUALITY ASSURANCE

A. MPI Standards:

1. Products: Complying with MPI standards indicated and listed in "MPI Approved Products List."

2. Preparation and Workmanship: Comply with requirements in "MPI Architectural Painting Specification Manual" for products and paint systems indicated.

B. Mockups: Apply benchmark samples of each paint system indicated and each color and finish selected to verify preliminary selections made under sample submittals and to demonstrate aesthetic effects and set quality standards for materials and execution.

1. Contracting Officer will select one surface to represent surfaces and conditions for application of each paint system specified in Part 3.

PEVI – 224362, 224363 09 91 10 - 3

a. Vertical and Horizontal Surfaces: Provide samples of at least 100 sq. ft.

b. Other Items: Contracting Officer will designate items or areas, as required.

2. Final approval of color selections will be based on benchmark samples.

a. If preliminary color selections are not approved, apply additional benchmark samples of additional colors selected by Contracting Officer at no added cost to the Government.

1.4 EXTRA MATERIALS

A. Furnish extra materials described below that are from same production run (batch mix) as materials applied and that are packaged for storage and identified with labels describing contents.

1. Quantity: Furnish additional paint for each material and color as outlined below:

a. P1: Siding, each color – 1 gallon

b. P2: Door, Windows, edge trim each color – 1 gallon

c. P3: Vinyl shutters each color– 1 pint

PART 2 - PRODUCTS

2.1 PAINT, GENERAL

A. Material Compatibility:

1. Provide materials for use within each paint system that are compatible with one another and substrates indicated, under conditions of service and application as demonstrated by manufacturer, based on testing and field experience.

2. For each coat in a paint system, provide products recommended in writing by manufacturers of topcoat for use in paint system and on substrate indicated.

B. Manufacturer:

1. PPG Paints systems are basis of design. Other approved systems by Sherwin Williams, Benjamin Moore, Diamond Vogel, Tenemec (p-6) will be reviewed. Note: include total number of finish coats that may vary pending upon the supplied system.

C. Colors: As selected, see end of this Section for Color Schedule or by Contracting Officer from manufacturer's full range to match existing exterior paint colors.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates and conditions, with painting subcontractor present, for compliance with requirements for maximum moisture content and other conditions affecting performance of work.

PEVI – 224362, 224363 09 91 10 - 4

B. Maximum Moisture Content of Substrates: When measured with an electronic moisture meter as follows:

1. Wood: 15 percent maximum.

C. Verify suitability of substrates, including surface conditions, and compatibility with existing finishes and primers.

D. Replace decayed cedar trim boards around doors windows.

E. Begin coating application only after unsatisfactory conditions have been corrected and surfaces are dry.

F. Beginning coating application constitutes Contractor's acceptance of substrates and conditions.

3.2 PREPARATION AND APPLICATION

A. Comply with manufacturer's written instructions and recommendations in "MPI Architectural Painting Specification Manual" applicable to substrates and paint systems indicated.

B. Clean substrates of substances that could impair bond of paints, including dirt, oil, grease, and incompatible paints.

1. Remove incompatible primers and re-prime substrate with compatible primers as required to produce paint systems indicated.

C. Apply paints by brush after spraying to produce surface films without cloudiness, spotting, holidays, laps, brush marks, runs, sags, ropiness, or other surface imperfections. Cut in sharp lines and color breaks.

D. Protect work of other trades against damage from paint application. Correct damage to work of other trades by cleaning, repairing, replacing, and refinishing, as approved by Contracting Officer, and leave in an undamaged condition.

E. At completion of construction activities of other trades, touch up and restore damaged or defaced painted surfaces.

F. All exterior woodwork is to be primed, including all exposed cut edges and back-primed prior to the application of topcoat.

PEVI – 224362, 224363 09 91 10 - 5

3.3 EXTERIOR PAINT COLOR LOCATION AND SCHEDULE

1. All colors to match existing colors. Each building is unique and must be field verified utilizing a color meter.

3.4 EXTERIOR PAINTING SYSTEM SCHEDULE

** PPG Paints following systems are basis of design. Other approved systems by Sherwin Wil-liams, Benjamin Moore, Diamond Vogel, Tenemec (p-6) will be reviewed. Note: include total number of finish coats that may vary pending upon the supplied system.

A. Wood Substrate: P-1: Siding,

a. Prime Coat: Not Necessary for this technology.

b. Topcoat: PPG Paints’ Manor Hall Exterior Urethane Modified Acrylic Latex, 70-300

Sat-in series or approved equal B. Dressed Lumber Substrates: P-2: Porch Fascia, Door, Windows, Edge Trim Typical, P-4: Window and Door Screens, Door Exterior

a. Latex over Alkyd System:

i. Prime Coat (Prime any bare wood): PPG Paints’ Seal-Grip Exterior Wood Primer, 17-941NF series or approved equal

ii. Topcoat: PPG Paints’ Manor Hall Exterior Urethane Modified Acrylic Latex, 70-500 series or approved equal

C. Wood lapboard Substrate (excluding roofs): P-3 Misc Trim Details.

a. Prime Coat: Not Necessary for this technology.

b. Topcoat: PPG Paints’ Exterior Urethane Modified Acrylic Latex, 70-300 Satin series or approved equal

Warranty:

1 year Construction Warranty shall be based on date of final acceptance of the project for workmanship.

Period of performance:

Work shall be completed within 90 calendar days after issuance of the notice to proceed.

Project Location: Perry’s Victory & International Peace Memorial

1. 50 Park Avenue, Put-in-Bay, OH 43456.

2. 60 Park Avenue, Put-in-Bay, OH 43456.

3. 80 Park Avenue, Put-in-Bay, OH 43456.

4. 90 Park Avenue, Put-in-Bay, OH 43456.

5. 100 Park Avenue, Put-in-Bay, OH 43456.

END OF SECTION 09 91 10

1. All colors to match existing colors. Each building is unique and must be field verified utilizing a color meter.