B08_Attachment_2_Statement_of_Work.pdf

Statement of Work

The Bureau of Land Management (BLM), Phoenix District Office (PDO), is seeking quotes from qualified vendor to decommission and upfit six (6) law enforcement vehicles as detailed below. The decommissioning and upfitting of all vehicles shall be done in three phases as detailed below.

Phases Decommission Vehicle IPlate Upfit Vehicle IPlate

1 2018 Dodge 2500 Power Wagon (PW) four door (4dr) four-wheel drive (4wd) trucks (all PWs are 2500 4dr, 4wd)

I622167 2023 Dodge

2500 PW

I624648

1 2018 Dodge 2500 PW I622249 2023 Dodge

2500 PW

I624612

2 2018 Dodge 2500 PW I622168 2024 Dodge

2500 PW

I624916

2 2019 Dodge 2500 PW I622876 2023 Dodge

2500 PW

I624611

3 2019 2500 Dodge PW I622826 2024 Dodge

2500 PW

I624917

3 2017 Chevy Tahoe 4dr 4wd sport utility vehicle (SUV).

I620866 2024 Chevy Tahoe

I625000

Decommissioning services shall include:

- Remove all emergency lights, aftermarket parts, radios and electrical components as necessary. Remove truck vault from bed/cargo area. Remove law enforcement stripes, markings, and badging. Plug holes (to prevent leakage) and reinstall OEM equipment back to factory condition. *Body and paint work (excluding damage done while in the contractor’s possession) are not the responsibility of the contractor. Final mechanical and body/paint rehabilitation (such as holes left from equipment removal) are not part of this contract.

If there are items that were supplied with the vehicle and determines the items will not be needed or needs replaced, the contractor will advise BLM. Any modification to the Statement of Work (SOW) must be approved by a BLM representative.

Upfitting services shall include:

Install and outfit emergency equipment, any other equipment such as but not limited to; prisoner cage, console, wire for radios, communication, ground positioning system (GPS), emergency lighting, storage racks, boxes or vaults, and any other equipment and/or electronic systems necessary for the vehicle to be fully operational and functional for law enforcement purposes.

Work Standards and Qualifications:

- Solder and shrink wrap all power connections, provide power protection for all devices, use proper hardware, terminals, and fasteners, protect wire bundles with loom, utilize quick disconnect plugs and sockets to shorten service, repair, removal, and replacement time. Also minimize connections to OEM wiring to eliminate OEM vehicle warranty issues. When required, all original equipment wiring connections are done in accordance with the manufacturer's vehicle upfitters guides. The contractor should be able to modify, adapt, troubleshoot, diagnose, and repair the majority of the equipment utilized in public safety vehicles rather than sending the equipment back to the manufacturer. The contractor should have metal fabrication capabilities and are able to design, build, modify, reinforce and repair metal related products such as weapons racks, mounts, brackets, partitions, and consoles. The contractor should retain woodworking skills to allow them to design, build, modify and repair wood products such as command centers, cargo boxes, mounting platforms and consoles. The contractor should be certified by Motorola and be authorized to sell, service, repair, install and remove all Motorola public safety products.

SERVICES:

Infrastructure, Metal Fabrication, Safety Equipment, Consoles, Light Systems, Equipment Mounting, Siren/Light Control Systems, Communication Site, Weapons Systems, Prisoner Transport Systems, Satellite Communication System, Bracketing, Reinforcing, Communications, Radios, mobile Two Way Radio, Prisoner Transport, Mobile Computers, Portable Two Way Radio, Repair, Mobile Video Systems, System Communication, Restoration, Mobile Chargers, Digital Communication, Wood Fabrication. Mobile Amplifiers, Local Area Network, Cabinets, Mobile Intercom Systems, Wide Area Network, Organizers, Mobile Storage Systems, Signal Enhancement, Modification, Mobile Power Protection Systems, WIFI, Mobile Signal Booster Systems, P/A Systems, Restoration, Mobile Command Systems, Paging Systems, Site Maintenance, Mobile Inverter / Converter Systems, Modems, Electrical, Mobile GPS Systems, Mobile Modems / Wireless Devices, Push Bumpers, Weatherproof Winches, Generator, Maintenance

(Vehicle 1, Phase One)

VEHICLES TO BE DECOMMISSIONED

Year: 2018 Make: Dodge Model: 2500 Vehicle License Plate: I622167 Vehicle Identification Number: 3C6TR5CJ9JG424592 Office/District: PDO

*Note: Pictures are representative and not always the exact vehicle or equipment. All Dodge 2500 Power Wagons are similarly equipped unless otherwise noted.

- All equipment not considered original equipment (OE) will be uninstalled (unless otherwise noted) and exterior holes plugged (leak prevention). Body and paint work to patch holes is not required.

o Emergency lights from front grill (x4), front/rear quarter panels (x4), tailgate/c-pillar (x4) and overhead lightbar o Spotlight o Radio antennas (x2) o SatRad antenna o PA system o Siren and Whelen control head o Motorola two-way radio o SatRad two-way radio o Havis computer mount and docking station.

o LED flashlight and charger o Aftermarket center consol and baseplate o Prisoner Cage o Interior white (x2) and red (x2) LED lights from headliner and switches from b-pillar.

o Truck Vault o Aftermarket light mount on front bumper o Ridgid scene lights in rear bumper to remain installed (does not need to function).

- Some emergency equipment from this vehicle will be transferred into I624648 (2023 Dodge 2500 PW) to include but not limited to:

o LED flashlight and charger o Truck vault.

o Motorola two-way radio, speaker, and antenna o SatRad Satellite two-way radio, speaker, and antenna o Ridgid LED light bar (front bumper) o Ridgid IR pods (front bumper) o Computer docking station (replacing mount)

Any equipment not being reused will be returned to the BLM and/or disposed of by contractor as determined by a BLM representative.

- Replacement of OE provided by BLM. Body parts such as grills, headliners etc will not be replaced as part of this contract. The items needing installation are listed below.

o Center Consol o HVAC ducting o Hook up right rear window/lock button for normal function.

- Remove all decals.

(Vehicle 2, Phase One)

Year: 2018 Make: Dodge Model: 2500 Vehicle License Plate: I622249 Vehicle

Identification Number: 3C6TR5CJ1JG424604 Office/District: PDO

- All equipment not considered original equipment (OE) will be uninstalled (unless otherwise noted) and exterior holes plugged. Body and paint work to patch holes is not required.

o Emergency lights from front grill (x2), front/rear quarter panels (x4), tailgate/c-pillar (x4), sideview mirrors (x2), between bumper and tailgate (x1) and overhead lightbar.

o Five (two red, three white) LED dome lights o Spotlight o Dash mounted radar unit o Angle armor ballistic panels in front doors.

o Radio antennas (x6) o SatRad antenna o PA system o Siren and Whelan control head o Motorola two-way radio o SatRad two-way radio o Havis computer mount and docking station.

o LED flashlight and charger o Aftermarket center consol and baseplate o Prisoner Cage o Interior white (x2) and red (x2) LED lights from headliner and switches from b-pillar.

o Juggernaut cell phone holder o Truck Vault o Secure idle/remote start o Setina push bumper o Amp power steps o Nuvi GPS navigation unit and mount (hard wired).

o Ridgid scene lights in rear bumper to remain installed (does not need to function).

- Some emergency equipment from this vehicle will be transferred into I624612 (2023 o LED flashlight and charger o Five (5) red and white LED dome lights o Truck vault.

o Motorola two-way radio, speaker, and antenna o SatRad Satellite two-way radio, speaker, and antenna o Ridgid white/amber LED light bar (front bumper) o IR pods (front bumper) o Computer docking station (replacing mount) o Angle armor ballistic panels in front doors o Amp power steps o Nuvi GPS navigation unit and mount o Juggernaut cell phone holder below.

o Center Consol

(Vehicle 3, Phase Two)

Year:2018 Make: Dodge Model: 2500 Vehicle License Plate: I622168 Vehicle

Identification Number: 3C6TR5CJ0JG424593 Office/District: PDO otherwise noted) and exterior holes plugged. Body and paint work to patch holes is not required.

o Emergency lights from front grill (x4), front/rear quarter panels (x4), tailgate/c-pillar (x4), sideview mirrors (x2) and overhead lightbar.

o Spotlight o IR light pod (behind grill) o Radio antennas (x1) o SatRad antenna o PA system o Siren and Whelan control head o Motorola two-way radio o Angel Armor ballistic panels in front doors o SatRad two-way radio o Havis computer mount and docking station.

o Prisoner Cage o Interior white (x2) and red (x2) LED lights from headliner and switches from b-pillar.

o Truck Vault o Amp power steps o Nuvi GPS navigation unit and mount o Ridgid scene lights in front grill and rear bumper to remain installed (does not need to function).

- Some emergency equipment from this vehicle will be transferred into I624916 (2024 o LED flashlight and charger o Truck vault.

o Motorola two-way radio, speaker, and antenna o SatRad Satellite two-way radio, speaker, and antenna o IR pod (front bumper) o Computer docking station (replacing mount) o Angel Armor ballistic panels in front doors o Amp power steps below.

o Center Consol

(Vehicle 4, Phase Two)

Year:2019 Make: Dodge Model: 2500 Vehicle License Plate: I622876 Vehicle

Identification Number: 3C6TR5CJXKG681584 Office/District: PDO not required.

o Emergency lights from front grill (x1 red/blue lightbar), front/rear quarter panels (x4), tailgate/c-pillar (x4), and overhead lightbar.

o Spotlight o Radio antennas (x2) o SatRad antenna o PA system o Siren and Whelen control head o Motorola two-way radio o SatRad two-way radio o Havis computer mount and docking station.

o Angel Armor ballistic panels in front doors.

o Interior white (x2) and red (x2) LED lights from headliner and switches from b-pillar.

o Truck Vault o Amp power steps o Nuvi GPS navigation unit and mount o IR pod from behind grill o Ridgid offroad lightbar and scene lights in front grill and rear bumper to remain installed (does not need to function).

- Some emergency equipment from this vehicle will be transferred into I624611 (2023 o LED flashlight and charger o Truck vault.

o Motorola two-way radio, speaker, and antenna o SatRad Satellite two-way radio, speaker, and antenna o Ridgid white/amber LED light bar (front bumper) o IR pods (front bumper) o Computer docking station (replacing mount) o Angel Armor ballistic panels in front doors.

o Amp power steps below.

o Center Consol

(Vehicle 5, Phase Three)

Year:2019 Make: Dodge Model: 2500 Vehicle License Plate: I622826 Vehicle

Identification Number: 3C6TR5CJ5KG666359 Office/District: PDO

- All equipment not considered original equipment (OE) will be uninstalled (unless otherwise noted) and exterior holes plugged. Body and paint work to patch holes is not required.

o Emergency lights from front grill (x1 red/blue chase bar), front/rear quarter panels (x4), tailgate/c-pillar (x4), and overhead lightbar.

o Spotlight o Radio antennas (x2) o SatRad antenna o PA system o Siren and Whelan control head o Motorola two-way radio o SatRad two-way radio o Havis computer mount and docking station.

o Angel Armor ballistic panels in front doors.

o LED flashlight and charger o Interior white (x2) and red (x2) LED lights from headliner and switches from b-pillar.

o Truck Vault o Amp power steps o Nuvi GPS navigation unit and mount o IR pod from behind grill o Ridgid offroad lightbar and scene lights in front grill and rear bumper to remain installed (does not need to function).

- Some emergency equipment from this vehicle will be transferred into I624917 (2024 o Truck vault.

o Amp power steps o Motorola two-way radio, speaker, and antenna o SatRad Satellite two-way radio, speaker, and antenna o Ridgid white/amber LED light bar (front bumper) o Computer docking station (replacing mount) below.

o Center Consol

(Vehicle 6, Phase Three)

Year:2017 Make: Chevy Model: Tahoe Vehicle License Plate: I620866 Vehicle

Identification Number: 1GNSKFEC4HR172510 Office/District: PDO

*Note: Pictures are representative and not always the exact vehicle or equipment.

not required.

o Emergency lights from front grill/bumper (x4), rear quarter panels (x2), rear hatch (x1 chase bar), and overhead lightbar.

o Spotlight o Radio antennas (x1) o SatRad antenna o PA system o Siren and control head o Motorola two-way radio o SatRad two-way radio o LED flashlight and charger o Aftermarket center consol and baseplate o Prisoner Cage o Truck Vault o Winch mount bumper.

o Rear door cover panels o Any remaining K-9 heat alert fan systems and wiring (partially decommissioned)

- Some emergency equipment from this vehicle will be transferred into I625000 (2024 Chevrolet Tahoe) to include but not limited to:

o Motorola two-way radio, speaker, and antenna o SatRad Satellite two-way radio, speaker, and antenna below.

o Center Consol o Both rear door panels o Hook up rear window/lock buttons for normal function.

(Vehicle 1, Phase One)

VEHICLES FOR EQUIPMENT UPFITTING

Year:2023 Make: Dodge Model: Ram 2500 Vehicle License Plate: I624648 Vehicle

Identification Number: 3C6TR5CJ1PG632488 Office/District: PDO

* Equipment showing R&I (remove and install) to be used from previous build. The cost of removing items should already be covered in the decommissioning estimate.

* Equipment showing P&I (purchase and install) to be sourced by the contractor. If a piece of equipment is needed to complete the installation, the contractor must include price of equipment in the contract costs. Some items will be supplied by the BLM (agency), they will show as “Install” and noted as provided. All other items such as brackets hardware wiring connectors etc. will be supplied by the contractor.

* Vehicles are resold at the end of service life. The agency is responsible to refurbish certain modifications before sale. Builder should avoid modifications to the body or factory wiring when/where feasible. This includes modifications that may affect the factory vehicle warranty.

If the contractor has suggestions to limit modifications, they should be discussed with the agency point of contact (POC).

FRONT GRILL/ FRONT QUARTER PANEL/REAR QUARTER PANEL (ON BED)

1. Remove and Install (R&I)- Ridged light bar on front bumper (fabrication as necessary, see

Picture #1).

2. R&I - Two IR lights in/on front bumper of vehicle (fabrication as necessary, see Picture #1).

3. Purchase and Install (P&I) – FOUR (4) surface mount/low profile red/blue LED flashing emergency lights on left and right front/rear quarter panels (see Picture #2).

4. P&I – Four (4) surface mount/low profile red/blue LED flashing emergency lights on grill (see Picture #1).

5. P&I - Siren speaker behind grill/bumper.

6. P&I - Two (2) Wig-Wag Flasher Control for Headlights (high beam) and/or similar OBD controlled flasher.

*Installation note – Do NOT install strobe lights in headlight housing. Historically any modification to the housing has resulted in moisture and dust being inadvertently introduced into the headlight.

REAR BED / TAILGATE / Bumper

1. P&I -TWO (2) surface mount/low profile red/blue/white LED flashing emergency lights on rear tailgate, upper right and upper left. White wired to switch for reverse/rear scene lighting control head multifunction or separate switches (see Picture #3).

2. P&I - Two (2) surface mount/low profile red/blue/white LED flashing emergency lights mounted to left and right C pillar facing rear. White wired to reverse/rear scene lighting control head multifunction or separate switches (see Picture #3)

3. R&I - Truck Vault rear bed cargo cabinet.

4. R&I - Cell booster, antenna to be installed behind the cab at the height of the bed rail

(fabricate brackets as necessary). Installation should not interfere with function (Antenna is spring mounted, should not collide with cab. Attempt to maximize cargo bed space).

ROOF

1. P&I – One (1) 55” SoundOff MPower low profile lightbar. Flashing Red & blue, one solid red (CA Compliant), full flood (white) with lights directly over driver and passenger seat or full flood (white) all forward facing (All White Forward-Facing Switch in Control Head).

2. R&I - Radio antennas (2+) as necessary (regular, SAT RAD and Motorola Radio).

Placement of antennas drivers’ side to passenger: First slot: SAT Radio, Second slot:

Motorola Radio.

3. P&I - One (1) “210” Large call sign decal on roof, black in color.

INTERIOR / DASH/ DOORS

1. P&I – Two (2) LED dome light (red, white) over center console to operate from switches located on Control Switch Panel (see Center Console #7).

2. P&I – Two (2) LED dome light (one red, one white) over backseat area on driver side (Operation from separate switches on passenger side B-pillar).

3. R&I - LED flashlight and charger on prisoner cage to the right of the passenger seat (see picture #9)

4. P&I – Power Invertor for external electrical outlets. Behind drivers front seat or drivers’ side rear seat area. Should be out of the way but reasonably accessible.

5. P&I – 5G Cell Booster. Sensor on dash or drivers side b-pillar.

6. Install - Radar unit. (provided by agency).

7. P&I - Havis heavy duty computer mount will be placed on the floor of the front passenger seat, as far left/next to center console (replacing worn mount). Panasonic Toughbook docking station (provided, reusing old unit) will be placed on top of the mount. Power supply wiring run to the mount (see picture #5).

8. P&I - Sound deadening material on interior roof panel to prevent adverse wind noise from overhead lightbar.

9. R&I – Angel Armor ballistic panels from front doors.

CENTER CONSOLE

*Keeping factory OE console, equipment to be placed as follows:

1. P&I - Emergency equipment/siren controller on headliner in front of overhead courtesy light console (see picture #4).

2. P&I – Two hour shut off timer for emergency equipment (does not included two-way radios or SatRad).

3. R&I - Motorola radio control head in depression top center of dash (see Picture #4).

4. P&I - Power cable for computer mount/docking station.

5. R&I - Motorola APX mobile radio under back seat. Radio needs to be wired per BLM specs. Brain/bricks needs battery constant to hold encryption. Radio Speaker mounted on PTC behind driver’s seat. (see picture #12).

*Installation note - Leg room in the front passenger seat is already limited due to the prisoner cage. Nothing should be installed that impedes the remaining seat adjustment.

6. P&I - PA mic/system mounted between console and dash on the driver’s side.

7. P&I - Axon signal unit (SKU 70112), set to activate on position three on Whelan control panel.

8. P&I - Switched “Blackout” to all exterior lighting including brake lights, rear bed lights and tow / trailer lights, AMP steps. No visible external light when “Blackout” engaged.

Switch in Whelen control head.

9. P&I - Control Switch Panel: 6 Rocker switches (or equivalent) minimum for:

a. Front off-road LED lightbar

b. Red LED above center console

c. White LED above center console

d. White LED Rear Prisoner

e. Rear scene white lights.

f. Empty

*Installation note - Placement in control panel is acceptable and preferred if space is available.

10. P&I - 12 volt, three plug auxiliary power ports x 2 (one mounted between dash and center console, one mounted in rear cargo area)

11. P&I - Motorola Handheld battery charger and wire to 12V ignition power.

12. P&I - Magnetic mic clip mount x 3 (Radio, PA, spare). Provide but do not install (to be determined by operator).

13. P&I - Ignition override / “Secure Idle” switch / remote start.

DRIVER SIDE AND BEHIND CONSOLE

1. P&I - Rifle and shotgun mount and two (2) locks with a 10 second timer. Both rifle mounts installed vertical behind center console in rear passenger area. Gun locking mechanisms need to be replaced with new items. Use of existing brackets is okay with serviceability inspection. Gun locks will be mounted onto a heavy-duty bracket and mounted to the prisoner cage at upper hoop and floor behind center console. This bracket will be made strong and sturdy to prevent theft, movement and rattling of weapons. A “safety stop” will be installed to prevent each rifle action from being charged (chambering a round) while the weapon is secured in the mount. Mount installation shall provide ample room for removal/installation, of firearms facing forward (for removal by a seated driver).

Shotgun (Remington 870) mounted on driver side; rifle (AR15) mounted on passenger side. Mounts should be adjustable for varying stock lengths. (see photo #9)

2. P&I - Two (2) Gun Release Switches to be hidden and located on: Location #1 -the DRIVER side area in the Whelen control head, lower righthand corner.

Location #2 - at the base of the "B" pillar, driver side, reachable from driver’s seat and REAR driver’s side door. B pillar gun release switch should be wired to battery positive. Switches must not interfere with seatbelt or safety devices.

UNDER REAR SEAT / UNDER HOOD

1. P&I - Auxiliary power/fuse block or box for all aftermarket electronics to access fuses that is easily accessible. Label all fuses.

2. P&I - Ignition override / “Secure Idle” safety switch / remote start override under hood OR dash for vehicle maintenance. Warning advisement sticker to be placed near vehicle battery.

*Installation note - Leg room in the front passenger seat is already limited due to the prisoner cage. Nothing should be installed that impedes the remaining seat adjustment.

Do not install fuse blocks or other accessories between the cage and front passenger seat.

PRISONER TRANSPORT CAGE

1. P&I – Setina (1K0574DRT192500WD) single prisoner transport cage (PTC) in right rear passenger seat position.

2. P&I - Steel window barrier in right rear passenger window.

3. Deactivate - Right rear passenger door lock and window controls but leave operable from driver door controls.

4. P&I - One (1) white LED dome light over prisoner seat (two switches; one accessible to the driver and one at passenger side b-pillar).

5. Install / Modify - Heating, ventilation, and air conditioning (HVAC) ducting from underneath the passenger seat and/or back of factory console into prisoner cage (see Picture #6).

*Installation Note: Temperatures in the prisoner cage have been difficult to maintain, especially in the summer months. Careful consideration should be taken to insure adequate HVAC and seatbelt function in the PTC. Some type of screen/louvers/grating should be installed to prevent objects being hidden or discarded in the vent.

REAR PASSENGER SEAT AREA

1. R&I - SAT RAD brain, fuse block and speaker (above head) to side of prisoner cage Plexiglass (see Picture #10).

2. R&I –Radio Speaker mounted on prisoner cage above head (see Picture #12)

3. Install – or fabricate a hanging hook at the top of plexiglass to hang jackets/body armor (see Picture #10).

VEHICLE STRIPING / DECALS

1. P&I - “210” Large Call Sign decal on roof, black in color (see Roof section).

2. Install - All vehicle striping / decals will be placed as in drawings included with striping kit.

(Provided). Remove decals from outgoing patrol vehicle.

Contractor supplied equipment:

Four (4) surface mounted dual color (red/blue) LEDs with white housings to be mounted on front and rear quarter panels.

Four (4) surface mounted dual color (red/blue) LEDs with black housings to be mounted on front grill.

Four (4) rear facing tri-color red/blue/white with white housings. Two rear-facing on c-pillar and two rear facing on tailgate.

Any equipment that is deemed out of date, damaged, and/or not working properly or is not compatible with the new patrol vehicle.

All wiring /switches, brackets, and any other parts necessary parts for installation, including a bracket with wiring to install a new SoundOff MPower 55” light bar.

Siren Speaker Headlight wigwag flasher to be install on high beam headlights.

Material needed to install call sign (210) on the roof of the patrol vehicle.

Sound Off Signal 55-inch MPower 6-inch lightbar (EMPLB00F6V-00K) One (1) white LED for illuminating the prisoner cage. These lights will be connected to a switch inside the rear door seal.

Power shut off timer (2 hour) for emergency equipment Control Switch Panel for Center Console.

PA Mic System.

Whelen Control Box.

Setina (1K0574DRT192500WD) Prisoner Cage (1-person quarter cage) and hardware.

SECURE IDLE / remote start, Secure-Idle Inc. or similar manufacture.

One (1) red LED for over driver’s compartment.

One (1) white LED for over driver’s compartment.

One (1) red LED for over driver side rear seat compartment.

One (1) white LED for over driver side rear seat compartment.

One (1) white LED for above prisoner cage.

One (1) 12-volt DC to 120-volt AC power inverter.

Two (2) two port USB charge socket.

Relays and equipment necessary for black out kit.

Two (2) three port 12-volt auxiliary plugs.

Three (3) radio Magnetic mic clips.

One (1) Dual Gun Rack for shotgun/rifle.

Sound deadening material for interior roof panel.

Black out kit 5G cell phone booster

***END ITEMS***

FRONT

SIDE

REAR

PICTURE #1

PICTURE #2

PICTURE #3

PICTURE #4

PICTURE #5

PICTURE #6

PICTURE #7

PICTURE #8

PICTURE #9

PICTURE #10

PICTURE #11

PICTURE #12

PICTURE #13

PICTURE #14

PICTURE #15

PICTURE #16

(Vehicle 2, Phase One)

Year:2023 Make: Dodge Model: Ram 2500 Vehicle License Plate: I624612 Vehicle Identification Number: 3C6TR5CJXPG632490 Office/District: PDO equipment in the contract costs. Some items will be supplied by the BLM (agency), they will when/where feasible. This includes modifications that may affect the factory vehicle warranty.

FRONT GRILL/ FRONT QUARTER PANEL/REAR QUARTER PANEL

1. Purchase and install (P&I) – One (1) Setina “Push Bumper” which includes Red and Blue

LED flashing lights.

2. Purchase and install – Two (2) low profile surface mount LED lights on front bumper or grill

3. R&I – Two IR lights in/on/ Setina Bumper.

4. P&I – Four (4) side facing Red and Blue LED light heads, surface mount / low profile lights (red/blue) on left and right quarter panels front and rear (White housing to match truck paint color).

5. P&I – Two (2) front facing Red and Blue LED light heads, surface mount on grill.

6. P&I – Two (2) front facing Red and Blue LED light heads, surface mount on mirrors.

7. P&I -Siren speaker behind grill / bumper.

8. P&I -Wig-Wag Flasher Control for Headlights TWO (high beam). Wired into headlights.

1. P&I -Two (2) surface mount / low profile Red and Blue LED flashing emergency lights on rear tailgate to side of LE emblems.

2. P&I - TWO red/blue LED lights surface mount / low profile (red/blue) mounted to left and right C pillar facing rear.

3. R&I - Truck Vault

4. P&I – Two (2) white LED Flood backup lights (IP68 minimum rated) mounted flush to rear bumper.

5. P&I – Three (3) Red and Blue LED strip lights mounted below the tailgate and above rear bumper. (See Picture #3)

1. P&I - 55” SoundOff MPower lightbar. Flashing Red & blue, one solid red (CA

Compliant), full flood (white) with lights directly over driver and passenger seat or full flood (white) all forward facing (All White Forward-Facing Switch in Whelen Control Head).

2. R&I - Radio antennas (3+) (regular, SAT RAD and Cell Booster)

Motorola Radio, Third slot: Cell Booster. (These will be behind the lightbar).

3. Install – “201” Large Call Sign decal on roof, black in color.

1. R&I - GPS navigation mount w/ power hard wired to main console power block

(Garmin Nuvi, etc., unit provided) overhead to upper windshield. Typically run 12 power outlet wire behind overhead liner. (See Picture #7)

2. R&I – LED Rigid dome lights as follows; Two LED Rigid dome light (one red driver side, one white passenger side) over center console (2 switches on center console Control Switch Panel). (See Picture #5 & #7)

3. R&I - LED Rigid dome light (one red, one white) x1 over backseat area on driver side

(2 switches on passenger side b pillar). (See Picture #11 & #13)

4. R&I – LED Rigid dome light (white only) installed over prisoner seat (2 switches; one switch at console and one at b-pillar). (See Picture #14)

5. R&I – Streamlight Ultra Stinger LED flashlight and charger. Behind passenger front seat on front of prisoner cage. (See Picture #8)

6. P&I – Power Invertor for external electrical outlets. Behind passenger front seat on front of prisoner cage. (See Picture #8)

7. P&I – 5G cell booster. Sensor on dash or drivers side b-pillar.

from overhead light bar.

9. P&I – Havis heavy duty computer mount will be placed on the floor of the front passenger seat, as far left/next to center console. (See Picture #4)

10. R&I - Panasonic Toughbook docking station will be placed on top of the mount. Power supply wiring run to the mount. (See Picture #4)

11. R&I – Juggernaut cell phone holder.

12. R&I – Angel Armor ballistic panels in front doors door.

1. P&I - Metal floor plate between seats for mounting console.

2. P&I – Center console.

3. P&I – Same style (as removed from I622249) console with swing arm installed as necessary. (See Picture #7)

4. P&I – Lockbox same width as console behind console or in the console as previous.

(See Picture #5)

5. P&I – Havis computer mount and power cord. (See Picture #4)

6. R&I – Computer docking station.

7. P&I - Master console power auto-off timer or Master Cut off switch. (See Picture #7)

8. R&I – Motorola APX mobile radio. Needs to be wired per BLM specs. Brain/bricks needs trickle charge to hold encryption. Radio speaker mounted on prisoner cage above driver’s head. (See Picture #12)

9. P&I – Whelen siren control box/panel.

10. P&I - PA mic/system and magnetic mic mount attached to center consol.

11. P&I – Control Switch Panel: 6 Rocker switches minimum on console for:

a. Front off-road driving lights-white

b. Front off-road driving lights-amber

c. Front IR Light

d. Cruise function (red and blue reduced power)

e. Red LED above center console

f. White LED above center console

g. White LED Rear Prisoner

h. Empty/Spare

12. P&I - Two (2) 12 volt, plug auxiliary power ports. One mounted on center console and one mounted in rear cargo area.

13. Install – Motorola handheld radio battery charger to side of console and wire to 12v ignition power. (Provided)

14. P&I – Radio MAGNETIC mic clip mount x 3 center console. Radio, PA System and radar remote.

15. P&I – Flush mount 2 port USB charge socket.

16. P&I – Ignition override / “Secure Idle” switch / remote start same as previous vehicle.

17. R&I – Motorola Bluetooth mic charger (PROVIDED).

18. P&I – Necessary components for switched “Blackout” to all exterior lighting including brake lights, rear bed lights and tow / trailer lights, AMP steps. No visible external light when “Blackout” engaged. Switch in Whelen Control Head.

*Installation note: Placement of equipment in consol front to back; First slot: Motorola Radio, Second slot: Whelen controller, Third slot: control switch panel, Fourth slot: open storage, Fifth slot: lockbox or placed behind console. (See Picture #4, #5, #7 & #8)

1. P&I - Rifle and shotgun mount and 2 locks on a 10 second timer. Both mounts configured vertically center console in rear passenger area. Driver should be able to retrieve rifles in a seated position facing forward.

2. P&I – Two (2) Gun Release Switches to be hidden and located on: Location #1on the driver’s side area of center console, in the Whelen control head. Location #2 at the base of the b-pillar, driver side, reachable from driver’s seat and rear passenger door (drivers’ side). This gun release switch will NOT be wired into master cut off switch. Shotgun mounted on driver side; rifle mounted on passenger side.

Switches must not interfere with seatbelt or safety devices.

*Installation Note: Gun Locks will be mounted onto a heavy duty-built bracket and mounted to the prisoner cage at floor, and behind center console with bracket. This bracket will be made strong and sturdy to prevent movement and rattling of weapons.

Bracket mount will provide ample room for removal of firearms. Shotgun mounted on driver side; rifle mounted on passenger side. (See PICTURE #6)

BEHIND FRONT PASSENGER SEAT / UNDER REAR SEAT / UNDER HOOD

1. P&I - Master auxiliary power/fuse block or box for all aftermarket electronics to access fuses (all fuses labeled) that are easily accessible.

2. P&I - Ignition override / “Secure Idle” switch / remote start

1. P&I - Setina (1K0574DRT192500WD) single prisoner transport cage (PTC) in right rear

2. Deactivate - Remove inside door handle, window roll down and locking system in door.

3. P&I - Steel window barrier in right rear passenger window.

4. Deactivate - Right rear passenger door lock and window controls but leave operable from driver door controls.

5. R&I - Rear / downward facing white and red LED flush / low profile mounted into prisoner cage area ceiling aimed at prisoner’s face & body.

6. P&I – Sufficient venting / air flow to prisoner transport area. (See Picture #14 &15)

1. P&I – Install flat deck cargo plate with 2” side rails over seat.

2. R&I – SAT RAD brain, fuse block and speaker (above head) to side of prisoner cage

Plexiglass. (See Picture #10)

3. R&I - Radio Speaker mounted on Prisoner cage above head. (See PICTURE #12)

4. P&I - Hanging hook at the top of plexiglass to hang jackets/body armor. (See Picture #10)

1. P&I – “201” Large Call Sign decal on roof, black in color.

2. Install / Modify- All vehicle striping / decals will be placed as in drawings included with striping kit. (Provided)

Vender supplied equipment:

Eight (8) surface mounted dual color (red/blue) LEDs to be mounted on (4) front and rear quarter panels, (2) rear facing c pillar and (2) rear facing on tailgate. (with white housing).

Two (2) surface mounted dual color (red/blue) LEDs to be mounted on front grill.

Two (2) surface mounted dual color (red/blue) LEDs to be mounted on front mirrors.

Setina “push bumper” (PV540L) with four red/blue LEDs.

Armrest pad with a Havis armrest pad and mounting brackets.

Havis computer stand and hardware.

Any equipment that is deemed out of date, damaged, and/or not working properly or is not compatible with the new patrol vehicle.

All wiring /switches, brackets, and any other parts necessary parts for installation, including a bracket with wiring to install a new SoundOff MPower 55” light bar.

Two (2) rear Rigid bumper lights.

Siren Speaker Three (3) Red/Blue LED strip lights for above bumper below tailgate in crevis.

One (1) 20” or similar bar: White and Amber LED off-road light Two (2) Headlight wigwag flasher to be install on high beam headlights.

Material needed to install call sign (201) on the roof of the patrol vehicle.

Sound Off Signal 55-inch MPower 6-inch lightbar (EMPLB00F6V-00K Center Console (same or like what is in vehicle) and hardware to mount, with Lockbox.

One (1) white LED for illuminating the prisoner cage. These lights will be connected to switches inside the rear door seal.

Master Cut Off switch attached to console.

Control Switch Panel for Center Console.

PA Mic System.

Whelan Control Box Setina (1K0574DRT192500WD) Prisoner Cage (1-person quarter cage) and hardware.

Secure Idle / remote start, Secure-Idle Inc. or similar manufacture.

One (1) red LED for over driver’s compartment.

One (1) white LED for over driver’s compartment.

One (1) red LED for over driver side rear seat compartment.

One (1) white LED for over driver side rear seat compartment.

One (1) white LED for above prisoner cage.

Power inverter.

One (1) two port USB charge socket.

Black out kit.

12 Volt plug auxiliary x2

3 radio Magnetic mic clips.

Gun Rack shotgun/rifle – vertical.

5G cell phone booster with 13’ antenna.

(Vehicle 3, Phase Two)

Year:2024 Make: Dodge Model: Ram 2500 Vehicle License Plate: I624916 Vehicle

Identification Number: 3C6TR5CJ1RG226617 Office/District: PDO equipment in the contract costs. Some items will be supplied by the BLM (agency), they will when/where feasible. This includes modifications that may affect the factory vehicle warranty.

1. Purchase and Install (P&I) - 20” Ridged white/amber +light bar on front bumper

(fabrication as necessary, see Picture #1).

3. R&I - Two IR lights in/on front bumper of vehicle (fabrication as necessary, see Picture

4. P&I - Four (4) surface mount/low profile red/blue LED flashing emergency lights on left and right front/rear quarter panels (see Picture #2).

5. P&I - Four (4) surface mount/low profile red/blue LED flashing emergency lights on grill

6. P&I - Siren speaker behind grill/bumper.

7. P&I - Two (2) Wig-Wag Flasher Control for Headlights (high beam) and/or similar OBD

8. Remove and Install (R&I) - Amp power steps

1. P&I -Two (2) surface mount/low profile red/blue/white LED flashing emergency lights

3. P&I - One (1) “209” Large call sign decal on roof, black in color.

mounted on PTC behind driver’s seat. (see picture #12).

*Installation note - Leg room in the front passenger seat is already limited

d. White LED Rear Prisoner

2. P&I - Rifle and shotgun mount and two (2) locks with a 10 second timer. Both locking mechanisms need to be replaced with new items. Use of existing brackets is okay with serviceability inspection. Gun locks will be mounted onto a heavy-duty bracket and mounted to the prisoner cage at upper hoop and floor behind center console. This bracket will be made strong and sturdy to prevent theft, movement and rattling of weapons. A “safety stop” will be installed to prevent each rifle action from being charged (chambering a round) while the weapon is secured in the mount. Mount installation shall provide ample room for removal/installation, of firearms facing forward (for removal by a seated driver).

Shotgun (Remington 870) mounted on driver side; rifle (AR15) mounted on

3. P&I - Two (2) Gun Release Switches to be hidden and located on: Location #1 -

Location #2 - at the base of the "B" pillar, driver side, reachable from driver’s seat

2. P&I - Ignition override / “Secure Idle” safety switch / remote start override under hood

OR dash for vehicle maintenance. Warning advisement sticker to be placed near vehicle battery.

*Installation note - Leg room in the front passenger seat is already limited due to the

3. Deactivate - Right rear passenger door lock and window controls but leave operable from driver door controls.

Picture #6).

*Installation Note: Temperatures in the prisoner cage have been difficult to maintain, especially in the summer months. Careful consideration should be taken to insure

1. P&I - “209” Large Call Sign decal on roof, black in color (see Roof section).

2. Install - All vehicle striping / decals will be placed as in drawings included with striping kit. (Provided). Remove decals from outgoing patrol vehicle.

Contractor supplied equipment: Items per vehicle unless otherwise noted.

Four (4) surface mounted dual color (red/blue) LEDs with black housings to be mounted on front grill.

Four (4) rear facing tri-color red/blue/white with white housings. Two rear-facing on c-pillar and two rear facing on tailgate.

Any equipment that is deemed out of date, damaged, and/or not working properly or is not compatible with the new patrol vehicle.

All wiring /switches, brackets, and any other parts necessary parts for installation, including a bracket with wiring to install a new SoundOff MPower 55” light bar.

Siren Speaker Headlight wigwag flasher to be install on high beam headlights.

Material needed to install call sign (209) on the roof of the patrol vehicle.

Sound Off Signal 55-inch MPower 6-inch lightbar (EMPLB00F6V-00K) One (1) white LED for illuminating the prisoner cage. These lights will be connected to a switch inside the rear door seal.

Control Switch Panel for Center Console.

PA Mic System.

Whelen Control Box.

Setina (1K0574DRT192500WD) Prisoner Cage (1-person quarter cage) and hardware.

SECURE IDLE / remote start, Secure-Idle Inc. or similar manufacture.

One (1) red LED for over driver’s compartment.

One (1) white LED for over driver’s compartment.

One (1) red LED for over driver side rear seat compartment.

One (1) white LED for over driver side rear seat compartment.

One (1) white LED for above prisoner cage.

One (1) 12-volt DC to 120-volt AC power inverter.

Two (2) two port USB charge socket.

Relays and equipment necessary for black out kit.

Two (2) three port 12-volt auxiliary plugs.

Three (3) radio Magnetic mic clips.

One (1) Dual Gun Rack for shotgun/rifle.

Black Out Kit Sound deadening material for interior roof panel.

One (1) 20” white/amber spot/flood off-road type lightbar One (1) IR LED pod lights (Note: keeping one of the IR pods off one previous build and installing both on front bumper).

(Vehicle 4, Phase Two)

Year:2023 Make: Dodge Model: Ram 2500 Vehicle License Plate: I624611 Vehicle Identification Number: 3C6TR5CJ3PG632489 Office/District: PDO equipment in the contract costs. Some items will be supplied by the BLM (agency), they will when/where feasible. This includes modifications that may affect the factory vehicle warranty.

1. Purchase and Install (R&I) – 20” Ridged white/amber light bar on front bumper

2. P&I - Two IR lights in/on front bumper of vehicle (fabrication as necessary, see Picture

3. P&I - Four (4) surface mount/low profile red/blue LED flashing emergency lights on left

4. P&I - Four (4) surface mount/low profile red/blue LED flashing emergency lights on grill

7. Remove and Install (R&I) - Amp power steps.

3. P&I - One (1) “203” Large call sign decal on roof, black in color.

mounted on PTC behind driver’s seat. (see picture #12).

*Installation note - Leg room in the front passenger seat is already limited locking mechanisms need to be replaced with new items. Use of existing brackets is okay with serviceability inspection. Gun locks will be mounted onto a heavy-duty bracket and mounted to the prisoner cage at upper hoop and floor behind center console. This bracket will be made strong and sturdy to prevent theft, movement and rattling of weapons. A “safety stop” will be installed to prevent each rifle action from being charged (chambering a round) while the weapon is secured in the mount. Mount installation shall provide ample room for removal/installation, of firearms facing forward (for removal by a seated driver).

Shotgun (Remington 870) mounted on driver side; rifle (AR15) mounted on

Location #2 - at the base of the "B" pillar, driver side, reachable from driver’s seat battery.

*Installation note - Leg room in the front passenger seat is already limited due to the

Picture #6).

*Installation Note: Temperatures in the prisoner cage have been difficult to maintain, especially in the summer months. Careful consideration should be taken to insure

1. P&I - “203” Large Call Sign decal on roof, black in color (see Roof section).

Four (4) surface mounted dual color (red/blue) LEDs with black housings to be mounted on front grill.

Four (4) rear facing tri-color red/blue/white with white housings. Two rear-facing on c-pillar and two rear facing on tailgate.

Any equipment that is deemed out of date, damaged, and/or not working properly or is not compatible with the new patrol vehicle.

All wiring /switches, brackets, and any other parts necessary parts for installation, including a bracket with wiring to install a new SoundOff MPower 55” light bar.

Siren Speaker Headlight wigwag flasher to be install on high beam headlights.

Material needed to install call sign (203) on the roof of the patrol vehicle.

Sound Off Signal 55-inch MPower 6-inch lightbar (EMPLB00F6V-00K) One (1) white LED for illuminating the prisoner cage. These lights will be connected to a switch inside the rear door seal.

Control Switch Panel for Center Console.

PA Mic System.

Whelen Control Box.

Setina (1K0574DRT192500WD) Prisoner Cage (1-person quarter cage) and hardware.

SECURE IDLE / remote start, Secure-Idle Inc. or similar manufacture.

One (1) red LED for over driver’s compartment.

One (1) white LED for over driver’s compartment.

One (1) red LED for over driver side rear seat compartment.

One (1) white LED for over driver side rear seat compartment.

One (1) white LED for above prisoner cage.

One (1) 12-volt DC to 120-volt AC power inverter.

Two (2) two port USB charge socket.

Relays and equipment necessary for black out kit.

Two (2) three port 12-volt auxiliary plugs.

Three (3) radio Magnetic mic clips.

One (1) Dual Gun Rack for shotgun/rifle.

Black Out Kit Sound deadening material for interior roof panel.

One (1) 20” white/amber spot/flood off-road type lightbar One (1) IR LED pod lights (Note: keeping one of the IR pods off one previous build and installing both on front bumper).

(Vehicle 5, Phase Three)

Year: 2024 Make: Dodge Model: Ram 2500 Vehicle License Plate: I624917 Vehicle

Identification Number: 3C6TR5CJ4RG226627 Office/District: PDO equipment in the contract costs. Some items will be supplied by the BLM (agency), they will when/where feasible. This includes modifications that may affect the factory vehicle warranty.

1. Purchase and Install (R&I) – 20” Ridged white/amber light bar on front bumper

2. P&I - Two IR lights in/on front bumper of vehicle (fabrication as necessary, see Picture

3. P&I - Four (4) surface mount/low profile red/blue LED flashing emergency lights on left

4. P&I - Four (4) surface mount/low profile red/blue LED flashing emergency lights on grill

7. Remove and Install (R&I) - Amp power steps.

3. P&I - One (1) “207” Large call sign decal on roof, black in color.

mounted on PTC behind driver’s seat. (see picture #12).

*Installation note - Leg room in the front passenger seat is already limited due to the locking mechanisms need to be replaced with new items. Use of existing brackets is okay with serviceability inspection. Gun locks will be mounted onto a heavy-duty bracket and mounted to the prisoner cage at upper hoop and floor behind center console. This bracket will be made strong and sturdy to prevent theft, movement and rattling of weapons. A “safety stop” will be installed to prevent each rifle action from being charged (chambering a round) while the weapon is secured in the mount. Mount installation shall provide ample room for removal/installation, of firearms facing forward (for removal by a seated driver).

Shotgun (Remington 870) mounted on driver side; rifle (AR15) mounted on

Location #2 - at the base of the "B" pillar, driver side, reachable from driver’s seat battery.

*Installation note - Leg room in the front passenger seat is already limited due to the

Picture #6).

*Installation Note: Temperatures in the prisoner cage have been difficult to maintain, especially in the summer months. Careful consideration should be taken to insure

1. P&I - “207” Large Call Sign decal on roof, black in color (see Roof section).

Four (4) surface mounted dual color (red/blue) LEDs with black housings to be mounted on front grill.

Four (4) rear facing tri-color red/blue/white with white housings. Two rear-facing on c-pillar and two rear facing on tailgate.

Any equipment that is deemed out of date, damaged, and/or not working properly or is not compatible with the new patrol vehicle.

All wiring /switches, brackets, and any other parts necessary parts for installation, including a bracket with wiring to install a new SoundOff MPower 55” light bar.

Siren Speaker Headlight wigwag flasher to be install on high beam headlights.

Material needed to install call sign (207) on the roof of the patrol vehicle.

Sound Off Signal 55-inch MPower 6-inch lightbar (EMPLB00F6V-00K) One (1) white LED for illuminating the prisoner cage. These lights will be connected to a switch inside the rear door seal.

Control Switch Panel for Center Console.

PA Mic System.

Whelen Control Box.

Setina (1K0574DRT192500WD) Prisoner Cage (1-person quarter cage) and hardware.

SECURE IDLE / remote start, Secure-Idle Inc. or similar manufacture.

One (1) red LED for over driver’s compartment.

One (1) white LED for over driver’s compartment.

One (1) red LED for over driver side rear seat compartment.

One (1) white LED for over driver side rear seat compartment.

One (1) white LED for above prisoner cage.

One (1) 12-volt DC to 120-volt AC power inverter.

Two (2) two port USB charge socket.

Relays and equipment necessary for black out kit.

Two (2) three port 12-volt auxiliary plugs.

Three (3) radio Magnetic mic clips.

One (1) Dual Gun Rack for shotgun/rifle.

Black Out Kit Sound deadening material for interior roof panel.

One (1) 20” white/amber spot/flood off-road type lightbar Two (2) IR LED pod lights

(Vehicle 6, Phase Three)

Year:2024 Make: Chevrolet Model: Tahoe Vehicle License Plate: I625000 Vehicle

Identification Number: IGNSKLED3RR199481 Office/District: PDO equipment in the contract costs. Some items will be supplied by the BLM (agency), they will when/where feasible. This includes modifications that may affect the factory vehicle warranty.

1. Purchase and Install (P&I) - 52" MPower light bar with a Clear lens kit and traffic advisory.

2. P&I - Metal bracket with flag mount attached to light bar mount.

3. Remove and Install (R&I) -Radio antennas (2) (two-way radio, SatRad)

4. P&I – 5G cell booster antenna

ELECTRONICS

1. R&I - Motorola Radio in center console.

2. P&I - 5G cell phone booster

3. P&I - LED lighting on rear hatch for cargo area

4. P&I - Red/White dome light front head liner

5. P&I - Protection system / timer / relay, black out relays horn, siren control siren, park kill, flasher system for headlights and backup lights integrated into electrical components.

6. P&I - Inverter AC/DC With Two USB Ports and Two outlets 400-Watt placement to be determined.

7. P&I - Two (2) weapons release timer and switches 10 second delay one on driver’s side siren control panel and the other on driver’s side b-pillar. B-pillar wired to battery positive constant. Insure

8. P&I - 6 rocker switches commercial grade on faceplate located on center console.

9. P&I - 4 CLA and faceplate W 2 USB Inserts on center console.

CONSOLE

1. P&I - Install metal floorplate between seats for mounting console, vehicle specific.

2. P&I - Havis/Troy/Jotto (or other) metal console with cup holders, storage box, with driver side arm rest.

3. Install – Factory original equipment auxiliary/USB plug outlet in console or dash as necessary (provided with vehicle).

4. R&I - Motorola mobile radio faceplate

5. R&I- SatRad satellite radio mic/controller on magnetic mic mount (location on console

TBD)

6. Install - Handheld radio battery vehicle charger (provided).

7.