B08 - Attachment 0002 - Specifications Checklist.xlsx
XLSX spreadsheet 15 KB Posted
- Attached to
- Ampliroll Hook Lift System Federal contract opportunity
- Solicitation number
- W52P1J-20-Q-3024
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| B08 - Attachment 0004 - Provisions and Clauses Applied to this Acquisitionlz.pdf | ||
| B08 - Attachment 0001 - Statement of Work.pdf | ||
| B08 - Request for Quotation W52P1J-20-Q-3024lz.pdf | ||
| B08 - Attachment 0003 - Price Matrix.XLSX | XLSX spreadsheet |
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Sheet1
| MUNICIPAL ENTITY |
| SPECIFICATIONS FOR |
| 65,000 LBS HOOKLIFT |
| Vendor Name: |
| DUNS: |
| CAGE Code: |
| Specification Instructions: Indicate compliance to the specifications on the "COMPLY YES/NO" line by each specification. | ||||
| Indicate any deviations from the specifications whether the minimum specifications are met or not on the | ||||
| "SPECIFICATIONS DEVIATIONS" line. Failure to comply with bid specifications may result in rejection of the bid. | ||||
| COMPLY | SPECIFICATION | |||
| YES | NO | DEVIATIONS | ||
| 1) HookLift System: reference model Ampliroll ALR 160/2000RT-22 | ||||
| a) The lift system shall implement a "roll off" type hook, to load, dump and unload a removable body. The loading apparatus must be hydraulically operated with no cables directly involved in the loading, dumping or unloading. | ||||
| b) Minimum capacity of 65,000 pounds | ||||
| c) HookLift length shall be 223" from loading pin to center of rear loading roller, and a truck CT of 188". | ||||
| d) Minimum dumping angle of 57 degrees | ||||
| e) HookLift shall be double articulating, pivoting at the rear most point to achieve a true dump. | ||||
| f) HookLift must have a sliding Jib arm to allow unit to slide a body forward to permit the HookLift to load and dump bodies shorter than its length. Body lengths usable shall be 16 to 24 ft. | ||||
| g) The sliding Jib shall be form fit into the main arm, with no less than 1/16" gap, top to bottom and left to right. Jibs with steel or nylon wear pads will not be permitted. | ||||
| h) HookLift must have a safety valve that does not allow the Jib to be retracted while in the dump mode. | ||||
| i) HookLift must have mechanical locks to create a rigid frame work while dumping. The latches must be engage within the first 4" of the forward travel of the Jib. This is to allow shorter bodies to dumped. | ||||
| j) All cylinders shall be equipped with counter balance valves, and bypass system lock, so that cylinders will hold their position in the event of pressure failure. | ||||
| k) HookLift shall have dual dump cylinders for better stability while dumping. | ||||
| l) HookLift sub-frame shall be Z-formed to give the greatest strength while also being able to flex with the truck frame to reduce cracks from stress. The sub-frame shall be a maximum height of 13.4" | ||||
| m) Rear body locks shall be pass through type to allow flexibility for placement of the body to maximize weight distribution. | ||||
| n) All pivot points shall have brass bushing, harden steel pins, and grease fitting for lubrication. | ||||
| o) Weight of HookLift shall not exceed 6420 pounds. | ||||
| p) Hook height shall be 61 3/4" from bottom of container rails to bottom of lifting pin. | ||||
| q) Rear roller stabilizer to be lowered during the loading faze to keep the front of the chassis from raising. | ||||
| 2) Hydraulic system shall be of high pressure type to minimize | ||||
| system weight and maximize payload. | ||||
| a) System components to be rated for 5200 psi with system relief set at 5000 psi. | ||||
| b) Pump to axial piston direct mount. | ||||
| c) Hydraulic flow 23 GPM at 1200 rpm. | ||||
| d) Hydraulic tubing shall be used everywhere practical. Lines are anchored to prevent vibration and wear. | ||||
| e) Reservoir 17gal capacity with 10 micron in tank filter. | ||||
| f) Cab controls shall be triple low pressure hydraulic to offer full feathering capabilities. |
Point of Contact Name
Point of Contact Phone Number
Pont of Contact Email Address
Signature of Individual Authorized to Bind the Organization to a quote submitted to the USG
Title of Signing Representative
Date Signed
File details come from the government source that posted it. Updated .