ATTMNT_02_FORM_462_Engineering_Data_Requirements.docx

REV:

ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

XXXXXXXXXXXXXXXX

2. PART NUMBER:

3. NATIONAL STOCK NUMBER:

1234-12-123-1234FG

4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC, WILL BE USED IN LIEU OF THE DATA INDICATED. THE SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO INDICATED.

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

NOSE CONE INSTL FS130.00 TO FS144.74 (A-10)

2. PART NUMBER:

160D111001-25

3. NATIONAL STOCK NUMBER:

1560-01-092-5700FJ

4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC., WILL BE USED IN LIEU OF THE DATA INDICATED. THE SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO INDICATED.

5. CONTRACTOR IS RESPONSIBLE TO COMPLETELY RESEARCH THESE MANUALS, SPECIFICATIONS, AND STANDARDS AND FULLY UNDERSTAND THE REQUIREMENTS NECESSARY FOR MANUFACTURE OF COMPONENT PARTS AND ASSEMBLIES. BEING ABLE TO READ AND INTERPRET A-10 LOFT DATA IS REQUIRED TO MANUFACTURE PART. ALL DEVIATIONS, MINOR AND MAJOR, FROM THE ENGINEERING DRAWING PACKAGE SHALL BE SUBMITTED TO 416 SCMS/GUMBA (A-10 STRUCTURES ENGINEERING).

6. WHEN MILITARY DOCUMENTS LISTED IN THE ENGINEERING DRAWING ARE CANCELLED THEY SHALL BE REPLACED BY THE INDUSTRY EQUIVALENT DOCUMENT SPECIFIED ON THE MILITARY DOCUMENT'S CANCELLATION NOTICE. THIS APPLIES TO THE ORIGINAL AIRCRAFT MANUFACTURER'S SPECIFICATIONS THAT ARE CITED IN THE DRAWING, AS WELL. THE CHARACTERISTICS OF TYPE, GRADE, CLASS, ETC. SPECIFIED IN THE CANCELLED MILITARY DOCUMENT SHALL BE MAINTAINED OR EXCEED THOSE CHARACTERISTICS WHEN APPLYING THE INDUSTRY EQUIVALENT DOCUMENT(S). WHEN THERE IS NO LISTED REPLACEMENT THE CONTRACTOR SHALL REQUEST AND RECOMMEND A SUBSTITUTE DOCUMENT FROM 416 SCMS/GUMBA (A-10 STRUCTURES ENGINEERING) THROUGH THE GOVERNMENT CONTRACTING OFFICIAL.

7. USE OF NORTHROP GRUMMAN SPECIFICATION Z-R701 IN CONJUNCTION WITH MIL-STD-130 IS MANDATORY TO ENSURE THE PROPER MARKING OF THE PARTS. (Z-R701 HAS UNLIMITED DATA RIGHTS IN JEDMICS)

8. THE FOLLOWING TOOLING IS IDENTIFIED FOR MANUFACTURE OF THIS PART:

TOOLING INFORMATION

160D111001-525ASF (ASSEMBLY FIXTURE)

LOCATION: AMARG, TUCSON, ARIZONA

LOCATED AT: 06A052E001F

ASSET #: 9A00797

BOX #: SI

TOOLING INFORMATION

160D111001-525SAF (SUBASSEMBLY FIXTURE)

LOCATION: AMARG, TUCSON, ARIZONA

LOCATED AT: 06A052G001F

ASSET #: 9A92080

BOX #: SI

9. THE TOOLING IS AVAILABLE AT AMARG, TUCSUN, ARIZONA. THIS TOOLING IS NOT REQUIRED BY THE GOVERNMENT FOR MANUFACTURING OF THIS PART. THE CONDITION OF THE TOOLING IS UNKNOWN. THE CONTRACTOR MAY USE THIS TOOLING AT THEIR OWN DISCRETION AND USEAGE WILL BE IN “AS IS CONDITION”. THE SHIPPING WILL BE AT CONTRACTOR’S EXPENSE. THE CONTRACTOR MAY DEVELOP/MANUFACTURE THEIR OWN TOOLING REQUIRED TO PRODUCE THIS PART. THE DEVELOPMENT OF NEW TOOLING WILL BE AT THE CONTRACTOR’S EXPENSE.

10. UPON COMPLETION OF THE CONTRACT THE CONTRACTOR WILL AT THEIR OWN EXPENSE RETURN SHIP ALL TOOLING TO HILL AIR FORCE BASE.

PREPARED BY:

RICHARD TILTON

OFFICE SYMBOL:

GBMAF

DATE:

20080411

PREPARED BY:

GREG BRODERICK

OFFICE SYMBOL:

416 SCMS/GUMBA

DATE:

20120502

HILL AFB FORM 462 Page 1 of 3 image1.jpeg image2.jpeg image3.jpeg