Attachments.pdf

For the best experience, open this PDF portfolio in

Acrobat X or Adobe Reader X, or later.

Get Adobe Reader Now!

http://www.adobe.com/go/reader

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

A. CONTRACT LINE ITEM NO. B. EXHIBIT C. CATEGORY:

TDP TM OTHER NDTI

D. SYSTEM/ITEM

6135011862891ES*

E. CONTRACT/PR NO.

FD2020-22-51240

F. CONTRACTOR

1. DATA ITEM NO.

B001

2. TITLE OF DATA ITEM

Test Procedure

3. SUBTITLE

First Article Inspection Report, Contractor Test

4. AUTHORITY (Data Acquisition Document No.)

DI-NDTI-80603A

5. CONTRACT REFERENCE

Airmunition Specification

6. REQUIRING OFFICE

AFLCMC/EBHJ

7. DD 250 REQ

SD

9. DIST STATEMENT

REQUIRED

B

10. FREQUENCY

1TIME

12. DATE OF FIRST SUBMISSION

BLK 16

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

8. APP CODE

N/A

11. AS OF DATE

13. DATE OF SUBSEQUENT

SUBMISSION

ASREQ

Draft

Final

Reg Repro

16. REMARKS

BLK 4: Contractor's format required. Follow content preparation instructions per the Data Item Description. Incorporate the following applicable requirements:

a. Dimension and tolerances specified on the manufacturing data shall be listed in one column with the actual corresponding reading obtained from inspection of the part, listed in another column.

b. Material utilized in the manufacture of "First Article" item shall be identified and certified as conforming to applicable data requirements.

c. Certification that identification markings, i.e. part number per MIL-STD-130 and Federal Supply manufacturer (FSCM) per H4-1 Cataloging Handbook (if applicable) have been complied with.

e. The test report will be certified by the responsible DCMA/QAR.

(Authorization for any deviations from the requirements specified by the manufacturing data must be obtained from the procuring agency prior to inclusion in the test report).

BLK 7: The electronic receiving report shall be annotated with the Lot Number, National Stock Number, and Nomenclature. Electronic receiving report required via internet Wide Area Work Flow (WAWF) at https://wawf.eb.mil. The electronic receiving report shall be used only for this data item; do not combine other data item submittals with this requirement.

BLK 9: DISTRIBUTION STATEMENT B. Distribution authorized to U.S.

Government agencies, (Administrative/Operational Use) (Date of Contract Award). Other requests for this document shall be referred to AFLCMC/EBHJ.

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec.

2751, et seq.) or the Export Administration Act of 1979(Title 50, U.S.C. App. 2401 et seq.), as amended. Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoD Directive 5230.25.

DESTRUCTION NOTICE - Destroy by any method that will prevent disclosure of contents or reconstruction of the document.

BLK 12: Submit no later than 30 days after completion of First Article Acceptance Testing. Submit through WAWF under DoDAAC FA8213.

*135015254446ES.

FOB DESTINATION

EBH 22-124-002

Terry McCurdy, AFLCMC/EBHEC, 586-0535

WAWF 0 1 0

DoDAAC, FA8213

15. TOTAL 0 1 0

G. PREPARED BY

mccurdy.terry.d.1075978215

H. DATE

2022/05/04

I. APPROVED BY

hargrove.eric.v.1167016843

J. DATE

18. ESTIMATED

TOTAL PRICE

DD FORM 1423-1, FEB 2001 PREVIOUS EDITION MAY BE USED Page 1 of 1 Pages

17. PRICE GROUP

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. Please do not return your form to the above organization. Send completed form to the

B002

First Article Qualification Test Plan and Procedures

Qualification Test Plan

DI-NDTI-81307A

Airmunitions Specification

DD

A

BLK4: Contractor's format required. Follow content preparation instructions per the Data Item Description.

Lot Number, National Stock Number and Nomenclature. Electronic receiving report required via internet Wide Area Work Flow (WAWF) at:

https://wawf.eb.mil. The electronic receiving report shall be used only for this data item; do not combine other data item submittals

BLK 8: Comments/approval/disapproval will be submitted within 30 working days of receipt by AFLCMC/EBHJ.

Government agencies (Administrative/Operational Use) (Date of restricted by the Arms Export Control Act (Title 22, U.S.C. Sec 2751, et seq.) or the Export Administration Act of 1979 (Title 50, U.S.C, App. 2401 et seq.), as amended. Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoD Directives 5230.25.

BLK 10, 11, 12, 13: The contractor shall provide a Qualification Test Plan/Procedures 30 days after contract award, allowing for 30 days approval time. No changes to previously approved government Test Plans shall be made without prior approval from AFLCMC/EBHJ Engineering approval, IAW Airmunitions Specification.

BLK 14: Submittals shall be in Microsoft Office software or PDF format. Submit through WAWF, DoDAAC, FA8213.

*6135015254446ES.

EBH 22-124-001

ITEM DESCRIPTION

NSN

6135011862891ES

CAGE

81855

REFERENCE NUMBER

EAP-12294

NOUN

BATTERY,THERMAL

END ITEM

AGM-86 Cruise Missile

TCTO NUMBER TO NUMBER

11A15-1-387

CRITICALITY CODE

F

DEMILITARIZATION CODE

G

SECURITY CODE

MDC

WZH

ES CODE

W4

REMARKS

INITIATOR

NAME

KEOME.L.MADDEN1

ORGANIZATION / OFFICE SYMBOL

AFLCMC / EBHJ

DSN PHONE

775-4367

COMMERCIAL PHONE

801-775-4367

ITEM DESCRIPTION DATA

LENGTH ( IN )

8.1000

WIDTH ( IN )

4.4500

HEIGHT ( IN )

7.4500

WEIGHT ( LB )

12.0000

OTHER DIMENSIONS

ITEM MATERIAL

Thermal battery is a dual cell stack battery with an electrolyte that remains in a solid state prior to battery activation.

ITEM FUNCTION

Acft signal fire batteryy which in turns supply electrical powert to missile during flight

SAFETY CRITICAL SCREW

THREADED COMPONENT

ESD CEMS SENSITIVE DATA

STATEMENT OF HELIUM CONTENT (%) 0 PRECIOUS METAL INDICATOR CODE

GFM REQUIRED GFE REQUIRED GFP REQUIRED

JEWEL BEARING JEWEL BEARING RELATED

LEGACY ITEM DESCRIPTION

Page 1 of 1ITEM DESCRIPTION Version 2Generated by PRPS using Jasper Reports on 07 Apr 2022

ITEM DESCRIPTION

NSN

6135015254446ES

CAGE

4CF82

REFERENCE NUMBER

425000

NOUN

END ITEM

AGM-86 Cruise Missile

TCTO NUMBER TO NUMBER

11A15-1-387

CRITICALITY CODE

F

DEMILITARIZATION CODE

SECURITY CODE

U

MDC

WZH

ES CODE

W4

REMARKS

INITIATOR

NAME

KEOME.L.MADDEN1

ORGANIZATION / OFFICE SYMBOL

AFLCMC / EBHJ

DSN PHONE

775-4367

COMMERCIAL PHONE

801-775-4367

ITEM DESCRIPTION DATA

LENGTH ( IN )

8.1000

WIDTH ( IN )

4.4500

HEIGHT ( IN )

7.4500

WEIGHT ( LB )

12.0000

OTHER DIMENSIONS

ITEM MATERIAL

a dual cell stack battery with an electrolyte

ITEM FUNCTION

Acft sends signal that fire the battery which in turn provides electrical power to missile during flight

SAFETY CRITICAL SCREW

THREADED COMPONENT

ESD CEMS SENSITIVE DATA

STATEMENT OF HELIUM CONTENT (%) 0 PRECIOUS METAL INDICATOR CODE

GFM REQUIRED GFE REQUIRED GFP REQUIRED

JEWEL BEARING JEWEL BEARING RELATED

LEGACY ITEM DESCRIPTION

Page 1 of 1ITEM DESCRIPTION Version 4Generated by PRPS using Jasper Reports on 07 Apr 2022

REPSHIP Data Requirements for Individual Shipments of Hazardous Material (HAZMAT) and Inert Component Parts - Continental United States (CONUS) to CONUS, CONUS to Overseas or From All

Overseas Locations FROM: Shipping Activity To: Domestic Customer or Transshipping Activity Clearance Authority (Ocean) or Customer Service

Branch (CSB) (Air) or CONUS Sea Terminal

INFO: GACP TRANSPORTATION, HILL AFB UT - (AFLCMC / EBHMB)

email: ooalc.gacp.transportation@us.af.mil or FAX (801) 777-1089.

INFO: Sponsoring Service Accountable Supply Activity Ultimate Consignee/ Final Destination

SUBJ: Report of Shipment (REPSHIP)

1. Shipment Date written as a three-digit day of the year (Julian)

2. Estimated Time of Arrival (ETA) written as a three-digit day of the year (Julian) (Observe Standard Transit

Time (STT), if CONUS Truck Shipment and no Required Delivery Date (RDD) identified)

3. Required Delivery Date (RDD) or Delivery Date (DD), if specified

4. Carrier

5. Bill of Lading (BL) Number (Notes 1, 2, 3, 4)

6. Military Traffic Expediting-Greater Security (MTX-GS) Service Number (Notes 1, 2, 3)

7. Air Release Number (Notes 1, 2, 3) or for Surface Shipments, Export Traffic Release (ETR) Number and

Vessel Name and/or Voyage Document Number

8. Shipment (Cargo) Name (Example: Bombs)

9. Container and Seal Number (if applicable):

a. Container Transportation Control Number (TCN)

b. Total Weight of Contents

c. Rounds, Pieces, Weight, Cube, Condition code, and Lot Numbers (Note 4)

10. Security Risk Category (SRC), (E.G., Security Risk Category I, II, III, IV, Unclassified, Confidential, Secret, None)

11. Controlled Item Inventory Code (CIIC)

12. Total Net Explosive Weight (NEW)

13. Hazard Classification (s)

14. Department of Defense Identification Code / Navy Ammunition Logistic Code (DODIC/NALC). (Note 4).

15. Name, address, and phone number of person responsible for information contained in REPSHIP

NOTES:

1. When the conveyance contains more than one shipment unit, repeat the data elements in separately lettered paragraphs for each shipment unit.

2. Cargo for more than one vessel or flight, but shipped to Port of Embarkation (POE) in a single conveyance, is included in a single REPSHIP. When cargo for a single vessel is moved to the Seaport of Embarkation (SPOE) in more than one conveyance, repeat all the data elements as above in separate numbered paragraphs for each conveyance or REPSHIP.

3. A separate REPSHIP is used for each mode of shipment to the POE.

4. Lot number, DODIC and NALC are not mandatory fields. If available, they may be provided in the electronic

RESHIP or in the template above. If a CBL is used, the lot number and ammunition condition code should be included in the remarks section. Weapons must be identified on the CBL by each serial number contained within the shipment.

5. DODIC and NALC are codes used specifically for logistic administration and control of ammunition.

Attachment 1 mailto:ooalc.gacp.transportation@us.af.mil

1. Shipment Date written as a three-digit day of the year (Julian)

2. Estimated Time of Arrival (ETA) written as a three-digit day of the year (Julian) (Observe Standard Transit Time (STT), if CONUS Truck Shipment and no Required Delivery Date (RDD) identified)

3. Required Delivery Date (RDD) or Delivery Date (DD), if specified

4. Carrier

5. Bill of Lading (BL) Number (Notes 1, 2, 3, 4)

6. Military Traffic Expediting-Greater Security (MTX-GS) Service Number (Notes 1, 2, 3)

7. Air Release Number (Notes 1, 2, 3) or for Surface Shipments, Export Traffic Release (ETR) Number and Vessel Name and/or Voyage Document Number ...

8. Shipment (Cargo) Name (Example: Bombs)

9. Container and Seal Number (if applicable):

a. Container Transportation Control Number (TCN)

b. Total Weight of Contents

c. Rounds, Pieces, Weight, Cube, Condition code, and Lot Numbers (Note 4)

10. Security Risk Category (SRC), (E.G., Security Risk Category I, II, III, IV, Unclassified, Confidential, Secret, None)

11. Controlled Item Inventory Code (CIIC)

12. Total Net Explosive Weight (NEW)

13. Hazard Classification (s)

15. Name, address, and phone number of person responsible for information contained in REPSHIP

NOTES:

Statement of Work March 2021

PRESERVATION, PACKAGING & MARKING REQUIREMENTS

The contractor shall develop, implement and maintain the preservation, packaging and packing of all items to be delivered under the terms of this contract. Packaging procedures will be established in accordance with AFMCI 24-201, specifically Paragraph 3.7 and MIL-STD-2073-1, Standard Practice for Military Packaging, Packaging requirements are identified in the AFMC Form 158, Packaging Requirements submitted by the responsible packaging specialist. All “markings and labeling” of shipments shall conform to MIL-STD-129, DoD Standard Practice, Military Marking for Shipment and Storage. The contractor shall affix a completed DD Form 1574, Serviceable Tag-Materiel or DD Form 1574-1, Serviceable Label- Materiel to each unit pack or intermediate container and prime outer container(s). The tag or label will indicate the condition(s) of the materiel and to identify the individual article or contents, bundle, container to which they are securely attached.

INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES

(ISPM 15) REQUIREMENTS

The contractor shall use the wood packaging material regulation for international trade which describes Phytosanitary (including treatments) that have been approved for wood packaging material and provides for the approval of new or revised treatments. Use the latest revision of (ISPM 15), and the following statement complies with the United Nations-implemented restrictions on wood packaging material (WPM).

“This requirement is specifically concerned with invasive species such as pinewood nematode. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frames, and cleats. The statement below cites the requirements in detail and covers lumber for building containers and pallets used for deliveries resulting in worldwide shipments (direct vendor deliveries, Air Logistics complex (ALC), Container Consolidation Points (CCP), Aerial Ports, Water Ports, or other DoD installations).

ELECTROSTATIC MATERIAL (When Applicable) The Contractor shall apply provisions of MIL-STD-2073-1, when identifying all solid-state devices and modules containing diodes, translators, integrated circuits and/or other microelectronic components sensitive to electrostatic forces. All such items shall be packaged IAW MIL-STD-2073-1 in conjunction with ANS/ESD S20.20, using electrostatic free barrier materials and shall clearly bear “Electrostatic Sensitive Device” labels IAW MIL-STD-129, Department of Defense Standard Practice Military Marking for Shipment and Storage.

PALLETIZED UNIT LOADS

The Contractor shall apply provisions and methods of MIL-STD-147, Palletized Unit Loads to contracts requiring the preparation and shipment of bonded palletized unit loads for DoD facilities when applicable.

SPECIALIZED SHIPPING CONTAINERS

The contractor shall apply provisions of MIL-STD-648, Department of Defense Design Criteria Standard, Specialized Shipping Containers. This standard establishes general design guidelines and associated tests for specialized shipping containers used by the Department of Defense. Definitive requirements for specific containers will be defined by the individual specification, acquisition, or task order. This standard is intended to be used as the basic reference document in all specifications and standards prescribing performance requirements to be applied to a specialized shipping container. Compliance with this intent is expected through normal application of the specification or standard preparation and revision processes.

Statement of Work (Cont)

HAZARDOUS MATERIALS (When Applicable) The contractor shall ensure Hazardous shipments comply with International Civil Aviation Organization (ICAO), U.S. Code of Federal Regulations (CFR) Title 49, International Air Transport Association (IATA) Dangerous Goods Regulation, International Maritime Dangerous Goods Code (IMDG, Annex 1), and AFMAN 24-604, Preparing Hazardous Materials for Military Air Shipments. Packaging shall meet “DOT specification or a United Nation (UN) specification ” manufactured in accordance with 49 CFR, Part 178 and the final packages assembled IAW 49 CFR, Parts 100-185 as applicable. A Competent Authority Approval (CAA) shall be acquired from the responsible Associate Administrator or other designated Department official to perform a function requiring prior consent under the Hazardous Material Regulation (HMR). Package(s) shall be marked IAW MIL-STD-129, DoD Standard Practice, Military Marking for Shipment and Storage.

The contractor shall affix a completed DD Form 1574, Serviceable Tag-Materiel or DD Form 1574-1, Serviceable Label- Materiel to each unit pack or intermediate container and prime outer container(s). The tag or label will indicate the condition(s) of the materiel and to identify the individual article or contents, bundle, container to which they are securely attached. If a symbol is used to represent the manufacturer or the approval agency certifying compliance with 49 CFR 178, subparts L and M, the symbol must be registered with the U.S. Department of Transportation. A copy of the Contractor’s Test Report and signed certification that the package configuration meets both CFR and UN requirements shall be made available to the procuring contract office, as required, prior to acceptance or shipment of any portion of the product IAW Contract Data Requirements List (CDRL DI-PACK-81059B) (Reference AFMC Form 158). Safety Data Sheets (SDS) are required for known hazardous items and applicable items shown in FED-STD-313, Tables I and II. The SDS shall have any applicable identification number, such as National Stock Number or Special Item Number. A copy of the SDS shall be mailed or e-mailed no later than five (5) days prior to contractual delivery of items:

FAR clause 52.223-3, Hazardous Material Identification and Material Safety Data

SPECIAL PACKAGING INSTRUCTIONS RETRIEVAL & EXCHANGE SYSTEM

(SPIRES)

Contractors may request the use of SPIRES website to view item packaging requirements or search for Special Packaging Instruction drawings via the following website: https://spires.wpafb.af.mil/

REUSABLE CONTAINERS

The contractor shall safeguard all received reusable shipping containers that meet the requirements of the AFMC Form 158 and are suitable for return shipment of serviceable assets. The contractor shall dispose of and replace unserviceable containers with new containers that meet requirements of the AFMC Form 158.

Contact the Product Support Manager and Administering Contracting Office (ACO) for disposition instructions and replacement when Long Life Reusable Container(s) are received in an unserviceable condition.

https://spires.wpafb.af.mil/

REPORTING DISCREPANCIES

The contractor shall use Web Supply Discrepancy Report (WebSDR) to submit/reply to a Supply Discrepancy Report (SDR), when improperly packed assets are received/shipped in other than the contracted packaging requirements (coded data or Special Packaging Instructions (SPI) drawings) from Department of Defense (DoD) components or contractor activities. The contractor shall request a WebSDR account via the following website: https://www.transactionservices.dla.mil/daashome/homepage.asp

(See Defense Logistics Management (DLM) 4000.25-M, Volume 2, Supply Standard and Procedures, Chapter 17, Supply Discrepancy Reporting) http://www.dla.mil/HQ/InformationOperations/DLMS/

Exceptions when no damage has occurred are as follows:

- Items packaged before the current SPIdate.

- An alternate pack may be used, provided the prime Air Force Sustainment Complex, Packaging Office at the Air Logistics Complex (ALC) approves and issues a waiver, deviation number, which would be annotated on the exterior container on the lower right hand portion of the identification side of thecontainer.

- In accordance with Technical Order (TO) 00-85B-3, How to Package Air Force Spares, the contractor may substitute the next larger size fast pack, of the type I or type II to ship transportation priorities 1 and 2 shipments as long as there is no decrease in any of the container dimensions without the requirement of a waiver deviation. TO 00- 85B-3, para 4.2 can be accessed via the website:

- https://www.tinker.af.mil/Portals/106/Documents/Technical%20Orders/AFD-082416-00-85B-3.pdf

ASSIST Documents for Specifications Listed in the GSA Index of Federal Specifications, Standards and Commercial Item Descriptions The contractor shall use the ASSIST website to access specification, standards, data item descriptions documents listed in this contract solicitation:

FAR 52-211-2 Availability of Specifications, Standards, and Data Item Descriptions listed in the Acquisition Streamlining and Standardization Information System https://quicksearch.dla.mil/

AFSC

406 SCMS/GULAA

Attn: Dustin Hale

DSN: 777-8841

COMM: 801-777-8841

Email: dustin.hale@us.af.mil https://www.transactionservices.dla.mil/daashome/homepage.asp http://www.dla.mil/HQ/InformationOperations/DLMS/ https://www.tinker.af.mil/Portals/106/Documents/Technical%20Orders/AFD-082416-00-85B-3.pdf https://quicksearch.dla.mil/%23/

APPLICABLE GOVERNMENT PACKAGING DOCUMENTS

NOTE: UTILIZE THE MOST RECENT REVISION

AFI 24-602V2_AFGM2018-01, Preparation and Movement of Air Force Cargo

AFMAN 24-604, Preparing Hazardous Materials for Military Air Shipments

DLMS 4000.25, Defense Logistics Management Systems, Volume 2, Change 10, Supply Standards and Procedures, Chapter 17, Supply Discrepancy Reporting

DOT Title 29, Occupational Safety and Health Administration, Labor

DOT Title 49, Code of Federal Regulations (49 CFR), Transportation

International Civil Aviation Organization (ICAO) Technical Instructions

International Air Transport Association (IATA) Dangerous Goods Regulation

International Maritime Dangerous Goods (IMDG) Code

ISPM 15, International Standard Phytosanitary Measure Note: Marking Requirements may be found in the American Lumber Standards Committee, Incorporated Wood Packaging Material Enforcement Regulations dated November 07, 2014 and ISPM 15.

MIL-STD-2073-1E, Change 4, Standard Practice, for Military Packaging

MIL-STD-129R, Change 1, Department of Defense Standard Practice Military Marking for Shipment and Storage

MIL-STD-648E, Department of Defense Design Criteria Standard, Specialized Shipping Containers

MIL-STD-147E, Change 1, Palletized Unit Loads

MIL-HDBK-773B, Electrostatic Discharge Protective Packaging

TO 00-85B-3, How to Package Air Force Spares

FED-STD-313E, Federal Standard: Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities

Statement of Work (Cont)

HAZARDOUS MATERIALS (When Applicable)

SPECIAL PACKAGING INSTRUCTIONS RETRIEVAL & EXCHANGE SYSTEM (SPIRES)

REUSABLE CONTAINERS

Statement of Work (Cont)

REPORTING DISCREPANCIES

Exceptions when no damage has occurred are as follows:

ASSIST Documents for Specifications Listed in the GSA Index of Federal Specifications, Standards and Commercial Item Descriptions

AFSC

Statement of Work (Cont)

ATTACHMENT 2

USAF & USN CAD/PAD STATEMENT OF WORK - AMMUNITION DATA CARDS

January, 2018

1. Ammunition Data Cards (ADC) shall be prepared in accordance with MIL-STD-1168 (current revision) and shall follow the format required by the application identified as Worldwide

Ammunition-data Repository Program (WARP). All of the requirements of MIL-STD-1168 apply but some are tailored in accordance with MIL-STD-962 to meet CAD/PAD program requirements as listed below.

2. The criteria and procedures for the assignment of lot numbers for energetic materials

(pyrotechnics, propellants, explosives) including their constituents shall be in accordance with

MIL-STD-1168.

3. All energetic materials (pyrotechnics, propellants, explosives) used in assemblies and sub-assemblies/components (i.e., igniter cartridges, delay elements, primer assemblies, explosive cord, etc.) shall be entered in the ADC using the common name, actual/original manufacturer’s part number & revision, lot number, and date of manufacture. Traceability shall be ensured by the original manufacturer’s documentation such as Certificate of Conformance (COC), Certificate of Analysis (COA), Quality Assurance Record (QAR) Quality Inspection Record (QIR), Quality

Assurance Documents (QAD), Batch Record, or other equivalent documentation that would provide positive traceability in the event of a future product recall.

4. The contractor may list their own internal part number for energetic material that they re-designate or re-characterize but must also list the actual manufacturer’s part number, lot number, and date of manufacture in parentheses in a format that is searchable in WARP. Any

GFM/GFP provided under contract to the vendor should retain government provided part/lot numbers and nomenclature to retain traceability. Ingredients which are used to synthesize or that are blended in a process to make the end item energetic material are not required to be listed. Examples of blended or synthesized energetic materials that shall be listed are HNS, Lead

Azide, BKNO3, ZPP, HES 8028, etc. If the ages of energetic materials are older than the ages specified on the Airmunitions Specification or as specified elsewhere in the contract at the time the CAD/PAD devices become hermetically sealed, the date of energetic material recertification or any associated approved Request for Variance (RFV) shall be notated in the waivers and deviation description section.

5. Hardware components shall be fully traceable and identified by the original manufacturer’s lot identification information/documentation or qualified distributor’s documentation such as

Certificate of Conformance (COC), Certificate of Analysis (COA), Quality Assurance Record

(QAR), Batch Record, or other equivalent documentation that would provide positive traceability in the event of a future product recall. The actual date of manufacture is not required for any non-age degradable materials such as metal housings, tubes, sleeves, firing pins, nuts, bolts, washers, etc. The COC, COA, QAR, or Batch Record date(s) may be used for the DOM. Epoxies, sealants, curative, O-rings, and other organic materials shall be fully traceable to OEM with

DOM and traceable via the original manufacturer’s lot identification documentation such as

Certificate of Conformance (COC), Certificate of Analysis (COA), Quality Assurance Record

(QAR) Batch Record, or other equivalent documentation that would provide positive traceability in the event of a future product recall. Materials or components that do not affect the reliability or safety of the end item (i.e., solvents, paints, lacquers, labels, dust caps, etc.) do not need to be listed on the ADC.

6. The ADC data and information entered in WARP for all materials and components ideally shall stand alone for traceability to the actual manufacture’s information (i.e. Mfg P/N, Mfg date (as applicable), Mfg lot number etc.). If contractor uses their own P/N, reference date for acceptance or other “trace”/traceability identification used internally for the non-critical piece parts/materials, it shall be noted in the remarks section, i.e. “trace ID, or PO used for the

ATTACHMENT 2 (continued) following piece parts: (parts shall identified/listed)”, provided the field/entry method is searchable in WARP. If traceability documentation is “questionable” or in conflict and needs clarification, the applicable engineer or equipment specialist shall be contacted to resolve any issues.

7. A “sample” ADC is generated in WARP the first time an ADC is submitted by the contractor for applicable government reviews and approvals. Upon approval of the sample ADC, a final version for each production lot shall be completed in WARP and uploaded for Invoicing, Receipt, Acceptance, and Property Transfer (iRAPT - formerly WAWF) for review and acceptance prior to shipment of product by the applicable government authority. The WARP ADC program will not allow the submission of additional ADCs until such time as the sample ADC has been approved in the system. The sample ADC does not require the use of a “Z” interfix number used to identify it as a sample.

8. If any unique situations exist that may conflict with compliance, a resolution should be proposed by the contractor prior to contract award to determine possible work-around.

9. A hard copy of the applicable ADC(s) shall also be included with each shipment per applicable

ADC CDRL.

WARP will reside within the Munitions History Program (MHP). Additional details on these WARP applications are provided below.

MHP-WARP Access Procedures

Government or Contractor employee with CAC and AKO account:

(a) Click on the MHP hyperlink which is https://mhp.redstone.army.mil/

(b) Enter CAC PIN when prompted

(c) Click on WARP (ADC)

(d) Click on Help

(e) Click on WARP Request Access and follow instructions

Contractor or Government employee without CAC and AKO account: MHP-WARP uses PKI authentication requiring a DoD approved digital certificate as a security measure to protect the integrity of stored data. There are three vendors that have been approved to issue DoD approved certificates per an External Certification Authority (ECA) program. You are required to use one of the approved vendors listed on the following DISA website:

http://iase.disa.mil/pki/eca/index.html

A nominal fee is charged for each certificate. The Contractor, including any subcontractors, shall assume the responsibility for all costs of obtaining each digital certificate needed.

After the required certificate is obtained:

(a) Click on the MHP-WARP hyperlink: https://mhpwarp.redstone.army.mil/

(b) Enter ECA password

(c) Click on Help and follow the instructions for obtaining the necessary access

HELP Numbers are as follows:

MHP Access – (256)313-2143; DSN 897-2143

JMC Quality Administrators for WARP issues – (309)782-2697 or (309)782-7107 https://mhp.redstone.army.mil/ http://iase.disa.mil/pki/eca/index.html https://mhpwarp.redstone.army.mil/

ATTACHMENT 2 (continued)

Worldwide Ammunition-data Repository Program (WARP)

An online user’s manual will provide additional help and criteria in the development of an ammunition data card. It is recommended that you download and read the user’s manual prior to creating and filling out your initial ammo data card. The user's manual also contains screen shots, which depict what the data entry person will see during the ADC input process.

Ammunition Data Card Input

ADC input allows current contractors and government facilities the capability to create, and submit for approval, both sample ADCs and production lot ADCs which meet the format requirements of MIL-STD-1168 and as specified in this SOW for ADCs. ADCs are automatically forwarded to the respective Government Agency Responsible for Acceptance (GARA). The GARA in most cases is the Defense Contract Management Agency (DCMA) Quality Assurance Representative

(QAR), who reviews contractor input for accuracy and completeness, and after updating the disposition code for the specific lot, submits the ADC to the database. The contractor’s data entry person is granted access only to ADCs identified with its specific manufacturing code, as identified in

MIL-HDBK-1461, Manufacturer's Symbols. The use of previously inputted ADCs through the

TEMPLATE option significantly reduces input effort, while increasing accuracy and consistency of data.

Email Notification

WARP provides immediate, automated notification to process participants when actions are required. When the producer has completed an ADC submission, an email message is routed to the

GARA advising that an ADC awaits review and approval. If the GARA approves the ADC as submitted, the ADC is released to the WARP database and an email, with approved data card, is routed back to the originator. If the ADC requires modification or correction to conform with MIL-

STD-1168 and/or the approved format and technical content as approved by the government, an email is provided to the ADC originator advising that corrective action is required prior to approval.

Information Updates

It is important that the System Administrators are apprised when a producer receives a new contract. The producer shall notify usarmy.RIA.jmc.mbx.warp@mail.mil within 30 days after receipt of a new contract. Information to be included shall be the contract number, item, GARA, Manufacturer's identification symbol and the names of the individuals who will be inputting ADCs into the system. If you are a new producer and do not have a Manufacturer's identification symbol, you can obtain one by sending an email to usarmy.RIA.jmc.mbx.warp@mail.mil. The email must contain manufacturer's name, address where performance of the contract will take place, and a point of contact.

(End of statement of work)

AIRMUNITION SPECIFICATION

DATE: 4 May 2022

NSN: 6135011862891ES / 6135015254446ES

1. The contractor shall provide an advanced Report of Shipment (REPSHIP) to the consignee no later than 24 hours prior to the shipment arrival, and for ammunition shipments no later than two hours after shipment departure. A (REPSHIP) shall include all the following data in accordance with ATTACHMENT 1.

2. Ammunition Data Cards (ADC) shall be filled out; input in accordance with Attachment 2, Statement of Work – Ammunition Data Cards; and state quantity/serial number of lot acceptance test units in the remarks block. One hard copy of the ADC shall accompany shipments to each shipping location. CDRL (DI-MISC-80043B)

3. Items shall be marked in accordance with CAD/PAD Item Marking Instruction Version 1.5, 1 May 2019, reference attachment.

4. Shelf Life Code marking NOT required per MIL-STD-129.

5. Hazard Classification Information: See attached JHCS Records Hazard Class/Division: NR Storage Compatibility Group: S DOT Marking/EX Number: NSN 6135011862891 = EX1986040183 / NSN 6135015254446 =

EX2016090735

DOT Shipping Labels UN Number:

Proper Shipping Name: Not regulated as a Hazardous Material Net Explosive Weight per item (NEW): 0.000400 NEW Unit of Measurement: LBS

NEW for all packaging/shipping documents shall reflect the NEW identified above per JHCS or IHC.

If NEW is altered to adjust item performance and is greater than the weight listed, an ECP shall be submitted to the government prior to manufacturing or at least 60 days prior to shipping and shall include the SDS (formerly MSDS) and applicable supporting documentation.

6. All Engineering Change Proposals (ECPs), Notice of Revisions (NORs), and Request For Variances (RFVs formerly RFD/RFWs) affecting the approved product baseline configuration, acceptance test procedures, or manufacturing process of any item(s) on this contract shall be in accordance with EIA-649-B. Major ECPs with NORs and Critical/Major RFVs shall be submitted to the responsible Government Engineering Authority for review/disposition by CCB.

Minor/Administrative ECPs with NORs and Minor RFVs shall be processed by the:

COGNIZANT GOVERNMENT ENGINEER

ECPs -- CDRL (DI-SESS-80639E) NORs – CDRL (DI-SESS-80642E) RFVs – CDRL (DI-SESS-80640E)

Distribution Statement: B, Reason: Administrative or Operational (ref. DoDI 5230.24)

7. Item(s) must pass both gross and fine leak checks. MIL-STD-883K(2), Method 1014.16 may be used as guidance. The existing leak rate limit established for this item(s) will remain the same.

Contractor shall generate a Lot Acceptance Test Plan (LATP/ATP) with an analysis or test results showing compliance for Hill AFB engineering approval at least 90 days prior to commencement of Lot Acceptance Testing allowing for 30 days approval time after submission.

CDRL (DI-QCIC-80553A)

8. Electronic Systems to encompass system, subsystem, pieces parts and assemblies shall not contain any substitutes for Tin-Lead solder and finishes. The use of any Tin-Lead solder substitutes requires approval through PCO and cognizant engineer, REFERENCE:

“Airworthiness Advisory (AA-08-02) Lead-Free Electronics” and GEIA-STD-0005-1 & 2.

9. Lot Acceptance Test Requirements are: IAW LATEST GOVERNMENT APPROVED ATP:

Contractor

10. The contractor shall furnish a Lot Acceptance Test/Inspection Report in the following system(s): WAWF

CDRL: (DI-NDTI-80809B)

11. LOT ACCEPTANCE TEST: In the event of an end item failure, the contractor shall notify the PCO/ACO and Air Force Engineering Organization within 1 business day.

Air Force Engineering Organization: AFLCMC/EBHJ Organization E-mail: david.monk.1@us.af.mil

12. In the event of test failure(s), a Failure Summary and Analysis Report with proposed corrective actions/recommendations is required. CDRL: (DI-SESS-80255B)

13. The age of the energetic materials and components (i.e. ALL explosives, propellants, pyrotechnics, cartridges, and/or initiators) used in the manufacture of these items or sub-components shall not exceed 24 months based on the original manufacturing date. All energetic materials and components must be traceable to the original DoD qualified manufacturer and compliant with the ITAR part 120 and 121 (http://www.pmddtc.state.gov/regulations_laws/itar.html).

14. Raw (non-blended) ingredients & materials used in blended/mixed energetic materials such as, but not limited to: fuels, oxidizers, binders, curatives, sensitizers, plasticizers, stabilizers etc., shall not exceed 24 months since date of manufacture and comply with original manufacture’s Specification or MIL-STD. The government may waive the energetic and constituent material http://www.pmddtc.state.gov/regulations_laws/itar.html requirements listed above or portions thereof, on a case-by-case basis (when acceptable to the government) provided the contractor furnishes all details of the reason for the variance and the age, lot numbers, traceability, and other pertinent information/ test data and Certificate of Analysis/ Conformance (COA/COC) of the subject materials or components. The variance shall be submitted as a RFV and may be subject to, but not limited to, conditions such as sensitivity testing, stabilizer and analysis and/or dehumidification at vendor’s cost; therefore, vendor must plan accordingly. RFV not required provided vendor has approved energetic material and constituent management and recertification plan approved by HAFB technical authority for this specific contract and contract is executed with materials in compliance with said plan.

Recertification test data for materials shall be provided by vendor upon request at no additional charge to the government. All raw ingredients, materials and components must be traceable to the original DoD qualified manufacturer and compliant with the ITAR part 120 and 121.

15. This item is designated as a Critical Safety Item (CSI). Documentation for critical characteristics may be found in the contract, TDP, assembly/inspection procedures or QALI.

MRB approval authority shall be retained by government engineer. Other characteristics requiring inspection or special oversight from DCMA:

16. First Article Test/Inspection Report IAW AFMC Form 260. CDRL (DI-NDTI-80603A)

17. First Article Test Plan and Procedures. CDRL (DI-NDTI-81307A)

18. Contracts involving ammunition and explosives (AE) will contain:

- DFARS Title 48 Part 252.223-7002, Safety Precautions for Ammunition and Explosives

- DFARS Title 48 Part 252.223-7003, Change in Place of Performance - Ammunition and Explosives Additionally, if the scope of work includes air shipment of explosives, the safety specification should require contractor compliance with:

- AFMAN 24-204(I), Preparing Hazardous Materials for Military Air Shipments

CAD/PAD Item Marking Instruction, V 1.5

CAD/PAD Item Marking Instruction

Prepared By CAD/PAD Joint Program Office

NSWC IHEODTD and AFLCMC/EBHJ

Version 1.5 Dated 01 May 2019

1.

Purpose

Table of Contents

2. Scope Page 5

3. Marking Requirements Page 6

4. Placement of UID Markings Page 8

5. Items delivered in kit format Page 9

6. Waivers Page 9

References

NOTE: Use latest revision of all reference documents.

1. MIL-STD-130 Department of Defense Standard Practice Identification Marking of U.S.

Military Property

2. MIL- STD-1168 (current revision) Ammunition Lot Numbering and Ammunition Data Card

(Note section 3.1 for new lot assignment for “remanufactured CAD/PAD Components”)

3. ISO/IEC 16022 Information technology - Automatic identification and data capture techniques - Data Matrix bar code symbology specification

4. ISO/IEC 15434 Information technology - Automatic identification and data capture techniques - Syntax for high capacity ADC media

5. ISO/IEC 15418 Information technology - Automatic identification and data capture techniques - GS1 Application Identifiers and ASC MH10 Data Identifiers and maintenance

6. UNDER SECRETARY OF DEFENSE FOR ACQUISITION POLICY AND

TECHNOLOGY Department of Defense Guide to Uniquely Identifying Items version 1.6 (this document is available on line at http://www.acq.osd.mil/dpap/pdi/uid/index.html or from Defense Procurement & Acquisition Policy, 3060 Defense Pentagon, Room 3E1044, Washington, DC 20301-3060)

7. DEFENSE FEDERAL ACQUISITION REGULATION SUPPLEMENT 252.211-7003

Item Identification and Valuation (Copies of this document are available on line at http://farsite.hill.af.mil/ or from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954)

8. AFSCM 21-556 Vol. 2 Julian Date format

9. ANS MH10.8.2 - 2006 Data Application Identifier Standard

10. –ISO 28219 Labeling and Direct Product Marking with Linear Bar Code and Two- Dimensional Symbols http://www.acq.osd.mil/dpap/pdi/uid/index.html http://farsite.hill.af.mil/ http://farsite.hill.af.mil/

Figures

1. Determining IUID requirement

2. Sample UID Data Stream

3. Sample CAD/PAD Data Plate/Label

4. Sample of Etched Data

5. Sample CAD/PAD Small Item Data Plate/Label

1. Purpose.

The Under Secretary of Defense has implemented policy requiring DoD components meeting the requirements identified in Figure 1 to be marked with Item Unique Identifiers (IUID). Cartridge Actuated Devices and Propellant Actuated Devices (CAD/PAD) items, regardless of dollar value, are typically serially managed in aircraft maintenance data systems and therefore are applicable to the IUID requirement.

Additionally, the Air Force Aircrew Escape System Executive Working Group (AESEWG) and the egress system maintenance community has requested that CAD/PAD items be marked with Data Matrix ECC 200 on item data plates or items to enhance accuracy of aircraft maintenance data.

In accordance with MIL-STD-130, this marking instruction identifies marking requirements that meet the above objectives by tailoring Unique Identification (UID) requirements to include aircraft maintenance data requirements for both free text Human Readable Information (HRI) and Machine Readable Information (MRI), which are both mandated requirements for CAD/PAD items.

Figure 1. Determining UID Requirement

2. SCOPE.

This instruction identifies marking requirements applicable to suppliers/manufacturers of CAD/PAD components. It is applicable to both production of new CAD/PAD components and remanufacture of service returned, over-aged components. It identifies marking methods applicable to the various sizes and shapes of CAD/PAD components.

As of this writing, guidance regarding mandated transfer of data to the IUID registry can be found at “http://www.acq.osd.mil/dpap/pdi/uid/index.html”. Go to Training and Communication link, select IUID Toolkit (www.IUIDtoolkit.com), and select “Defense Suppliers”, then under “Submit”, select subsection “Registration of IUID Data11”, under Support Tools select “Data Submission”.

http://www.iuidtoolkit.com/

3. Marking Requirements.

Both Human Readable Information (HRI) and Machine Readable Information (MRI) are required (see section 4). In accordance with the Defense Federal Acquisition Regulation Supplement (DFARS), DoD has mandated the use of Data Matrix ECC 200 as the standard format for UID MRI markings. Guidance for the construct and application of Data Matrix markings is contained in MIL-STD-130 and the DoD UID Guide located at http://www.acq.osd.mil/dpap/pdi/uid/index.html, select Guides link.

3. 1. HRI Marking Requirements. The following HRI data is required (as a minimum):

- Item Nomenclature; Per applicable manufacturer drawing

- Manufacturer’s Commercial and Government Entity (CAGE); Five (5) alpha/numeric characters.

- Item Lot Number; Lot numbers shall be assigned IAW MIL-STD-1168 (current revision), unless otherwise directed. A new lot number and serial number shall also be assigned for “remanufactured” CAD/PAD components as opposed to adding a suffix to the original lot number for a “rework, overhaul or renovation” effort.

NOTE: The requirement for unique lot number has been deleted.

DOM is NOT required if the lot number contains the DOM as identified in MIL-STD-1168

- Item Serial Number; Serial number shall be up to eight (8) numeric characters.

The serial numbers shall be sequentially assigned and shall not be repeated until serial number 99,999,999 has been reached.

- Item manufacturer’s Part Number

NOTE: The weapon system Specification Number does not meet this requirement

- Optional markings: Additional markings (such as manufacturer’s name, logo, contract number) are acceptable, provided that space is available on the item/data label. Date of Manufacture (DOM); DOM shall be MM/YYYY and be the same date that is coded into the lot number.

NOTE: Markings and/or attachments shall make no reference to item installation requirements/procedures or shelf/service lives

S S S S S o

3.2. MRI Data Construct.

Data Matrix ECC200 markings shall be developed based on UID Data Construct #2 using Data Identifiers (DIs) in accordance with MIL-STD-130 and the DoD UID Guide (see Figure 2). To facilitate durability throughout the scanning life cycle, the largest symbol size, including quiet zone, shall be fitted within the available marking real estate. The symbol’s internal module (cell) sizes shall be no smaller than 0.0075 inch (0.19 mm) and no larger than 0.025 inch (0.64 mm). Marks shall contain only the data elements identified below:

NOTE: The actual UII will be comprised of CAGE, Part Number, and Serial Number data. The parenthesis surrounding the Data Identifiers are NOT encoded in the 2D symbol

(17V) Manufacturer’s Commercial and Government Entity (CAGE) code, 5 alpha/numeric characters

- (1P) Manufacturer’s Item Part Number, 18 alpha/numeric characters maximum

NOTE: The weapon system specification numbers do not meet this requirement

- (S) Item Serial Number, IAW HRI requirement, up to eight (8) numeric characters

- (30T) Item production Lot Number, IAW HRI requirement, 15 alpha/numeric characters maximum

NOTE: The data identifier for Lot Number has been changed from 1T to 30T

- (4D) Date of Manufacture (DOM), in Julian Date format, five (5) numeric characters:

Example: 08151 = 31 May 2008

The first two positions are the last two digits of the year, the last three positions are the Julian Date (001 through 366)

[)> R 06 G 17V 12345 G 1P 123456789-ABCDEFGH G S 12345678 G 30T ABC06D123-001 G 4D 08151 R E

Figure 2. Sample UID Data Stream

S S T

4. Placement of UID Marking. CAD/PAD items vary considerably in size and shape. A large percentage of these items are currently marked with HRI printed on data plates or labels permanently affixed to the item. The preferred method for incorporating the UID required MRI is to include it on the current data plate/label and, wherever possible, the supplier is to incorporate this concept. The following identifies known variations in marking and preferred MRI incorporation methods.

Note: Unless specifically identified as a requirement in the procurement contract, subcomponents of the End Item Assembly shall not be UID marked.

4.1. CAD/PAD Items Currently Marked with Data Plates, Labels, or Flag-Tags. The data plates/labels for these items shall be modified/arranged to allow space for the MRI per paragraph 3.2. Marking shall comply with MIL-STD-130 and the DoD UID Guide (see figure 3).

Figure 3. Sample Data Plate/Label

4.2. CAD/PAD Items Currently Marked With Ink or Laser Etching Directly on the Item.

Item marking shall be modified/arranged to allow space for the incorporation of ink or laser etched MRI per paragraph 3.2. Marking shall comply with MIL-STD-130 and the DoD UID Guide (see figure 4).

CAD/PAD Builder Inc.

Acft Explosive Component Noun

CAGE: 12345

P/N: 123456789-1234

Ser No: 0001 Lot No: ABC08D001-001

DOM: 04/2008

Figure 4. Sample of Etched Data

CAD/PAD Builder Inc.

Acft Explosive Component Noun

CAGE: 12345

P/N: 123456789-1234 Ser No: 0001

4.3. CAD/PAD Items Considered to be Too Small for HRI and MRI. These items shall be physically marked using currently approved methods for HRI. A self-adhesive label shall be supplied in the item inner packaging that includes the minimum HRI (per paragraph 3.1) and the MRI Data Matrix marking (per paragraph 3.2). The label shall be as small as possible (meeting MIL-STD-130 requirements for HRI) and will include only the minimum required data (see figure 5).

Figure 5. Sample Small Item Data Plate/Label

Note: This will allow the maintainer to scan the MRI from the label and the ability to affix it to the next higher assembly.

5. Kit Marking Requirements. Individual components procured and delivered in a “kit” or “ship-set” format shall each be marked with HRI and MRI as identified in sections 3 and 4.

The kit containers shall also be marked with HRI and MRI per sections 3 and 4.

Note: Individual components supplied in kits or ship-sets require unique item identifiers. Their markings shall not reflect those identifying the kit or ship-set.

5.1 Only the “kit “or “ship-set” will…