Attachment II Product Description_DVTAIRCOOLED-1-26.pdf

Air-Cooled Condensers Technical Guide

Models DVT

BN-RACCTB | Sept. 2016 Replaces BN-RACCTB April 2015

Features & Options �����������������������������������������������������������������������������������������������������������������������������������������2 Condenser Selection ���������������������������������������������������������������������������������������������������������������������������������� 3-4 Performance Data ������������������������������������������������������������������������������������������������������������������������������������������5 Dimensional Diagrams �����������������������������������������������������������������������������������������������������������������������������������6 Dimensional Data �������������������������������������������������������������������������������������������������������������������������������������������7 Specifications �������������������������������������������������������������������������������������������������������������������������������������������������7

© 2016 Heatcraft Refrigeration Products, LLC

DVT air-cooled condensers are available from 1 through 26 ton models.They are designed for efficient performance and low maintenance.

Table of Contents

Design Features n Horizontal or vertical air discharge n Attractive aluminum housing n Multi-circuiting at no additional charge n Energy efficient fan motors with internal overload protection and permanently lubricated ball bearings n Motors wired to a common junction box n Coated steel fan guards n Fully baffled fan sections to prevent windmilling

Available Optionsn Factory mounted head pressure control valves (consult factory) n Temperature or pressure activated fan cycling kits n Control power transformer for fan cycling kits (230V standard) n Alternate control voltages (115V or 24V) for fan cycling kits n BohnGuard coated or copper fins on condenser coil n Industrial coil coatings available (consult factory) n Single phase fan motors available on all models n Three phase motors available on models 005-026 n 575/3/60 motors available on models 005-026 n Sealtite wiring on models 005-026 n Variable speed fan motor options available on models 005-026 (consult factory)

Available Options

3 3

CONDENSER SELECTION

Capacity for air-cooled condensers are based on total heat of rejection (THR) at the condenser. THR is equal to net refrigeration at the evaporator (compressor capacity) plus the energy input into the refrigerant by the compressor (heat of compression).The heat of compression will vary depending on the compressor manufacturer, type of compressor and the operating conditions of the compressor. Whenever possible, it is recommended that you obtain the heat of compression value from the compressor manufacturer.

If this is not available, the THR can be estimated using the following formula:

THR = (Compressor Capacity) * (Heat of Compression Factor, Tables 1 & 2)

Table 1 contains heat of compression factors for suction-cooled compressors and Table 2 contains factors for open drive compressors. For refrigeration systems beyond the range of

Tables 1 and 2, use the following equations to estimate THR:

Open Compressors:

THR = Compressor Capacity (BTUH) + (2545) * (Brake

Horsepower, BHP)

Suction-Cooled Compressors:

THR = Compressor Capacity (BTUH) + (3413 * KW)

The condenser capacity is affected by its altitude.If the condenser location is above sea level, an additional correction is required to the THR, as follows:

THR (altitude) = THR* altitude Correction Factor, Table 3

Table 1. Heat of Compression Factor for Suction-Cooled Compressors

Table 2. Heat of Compression Factor for Open Drive Compressors

Evaporator Condensing Temperature °F

Temp.°F 90° 100° 110° 120° 130° 140°

-30° 1.37 1.42 1.47 — — —

-20° 1.33 1.37 1.42 1.47 — —

-10° 1.28 1.32 1.37 1.42 1.47 —

0° 1.24 1.28 1.32 1.37 1.41 1.47

5° 1.23 1.26 1.3 1.35 1.39 1.45

10° 1.21 1.24 1.28 1.32 1.36 1.42

15° 1.19 1.22 1.26 1.30 1.34 1.40

20° 1.17 1.20 1.24 1.28 1.32 1.37

25° 1.16 1.19 1.22 1.26 1.30 1.35

30° 1.14 1.17 1.20 1.24 1.27 1.32

40° 1.12 1.15 1.17 1.20 1.23 1.28

50° 1.09 1.12 1.14 1.17 1.20 1.24

Suction Temp.°F

Condensing Temperature °F

90° 100° 110° 120° 130°

-40° 1.56 1.63 1.72 1.81 1.94

-30° 1.49 1.55 1.62 1.70 1.80

-20° 1.43 1.49 1.55 1.62 1.70

-10° 1.38 1.43 1.49 1.55 1.63

0° 1.34 1.38 1.43 1.49 1.56

5° 1.31 1.36 1.41 1.48 1.55

10° 1.29 1.34 1.39 1.44 1.52

15° 1.26 1.31 1.36 1.41 1.48

20° 1.24 1.28 1.33 1.38 1.44

25° 1.22 1.26 1.31 1.36 1.42

30° 1.20 1.24 1.28 1.33 1.39

40° 1.17 1.20 1.24 1.28 1.33

50° 1.13 1.16 1.20 1.24 1.28

Step 1: Estimate Condenser THR

Obtain compressor heat of rejection from compressor manufacturer or calculate condenser THR estimate by multiplying compressor capacity by heat of compression factor from Tables 1 or 2 at given operating conditions.

THR = Compressor Capacity * Heat of Compression Factor

Step 2: Correct for Altitude

If condenser location is above sea level, correct for altitude by multiplying condenser THR by altitude correction factor from

Table 3.

THR = THR (from Step 1) *Altitude Correction Factor

Step 3: Calculate Design Condenser T.D.

Design Condenser T.D.= Condensing Temp.– Ambient Temp.

Altitude Correction Factor

0 1.00

1,000 1.02

2,000 1.05

3,000 1.07

4,000 1.10

5,000 1.12

6,000 1.15

7,000 1.17

Table 3. Altitude Correction Factors

Step 4: Condenser Selection

Condenser capacities for 60 Hz operation are located in Table

4. These capacities are given in MBH/°TD. Convert the THR calculated in step 2 to MBH/°TD by dividing by 1,000 to get THR in MBH. Then divide the THR by the design TD to get MBH/°TD.

Locate the capacity column and read down until you locate a value in the table equal to or just larger than the MBH/°TD calculated above. Read horizontally to the left and obtain the condenser model number.

THR (MBH) = THR (from Step 2) ÷ 1,000

THR (MBH/°T.D.) = THR (MBH) ÷ Calculated Design Condenser T.D.

Step 5: Calculate Actual Condenser T.D.and Condensing Temperature

Actual condenser T.D.can be calculated by dividing the design

THR by the 1°F T.D.Condenser T.D.Rating.

Actual T.D.= THR (MBH) ÷ (Rating at 1°F)

Actual condensing temperature can be calculated by adding the actual condenser T.D.to the design ambient temperature.

Actual Condensing Temp.= Ambient Temperature + Actual T.D.

CONDENSER SELECTION

5 5

Table 4. Performance Data for 60 Hz.

Table 5. Performance Data for 50 Hz.

DVT Model Capacity (MBH / 1˚F)

R-404A / R-507 R-407C * R-407A / R5407F R-448A * R-449A *

001 0.74 0.70 0.73 0.71 0.73

002 1.00 0.82 0.98 0.96 0.99

003 1.54 0.94 1.51 1.48 1.52

005 2.38 1.45 2.33 2.28 2.36

008 3.92 2.24 3.84 3.76 3.88

010 4.77 3.68 4.67 4.58 4.72

012 5.96 4.48 5.84 5.72 5.90

014 6.85 5.60 6.71 6.58 6.78

016 7.83 6.44 7.67 7.52 7.75

021 10.29 7.36 10.08 9.88 10.19

023 11.07 9.67 10.85 10.63 10.96

026 13.03 10.41 12.77 12.51 12.90

* Based on midpoint condensing temperature

DVT Model Capacity (kcal / hr / 1˚C)

R-404A / R-507 R-407C * R-407A / R-407F R-448A * R-449A *

001 310 291 304 298 307

002 420 395 412 403 416

003 640 602 627 614 634

005 990 931 970 950 980

008 1640 1542 1607 1574 1624

010 1990 1871 1950 1910 1970

012 2490 2341 2440 2390 2465

014 2860 2688 2803 2746 2831

016 3270 3074 3205 3139 3237

021 4280 4023 4194 4109 4237

023 4630 4352 4537 4445 4584

026 5430 5104 5321 5213 5376

* Based on midpoint condensing temperature

CONDENSER PERFORMANCE

18” 460mm

22” 560mm

13/32” x 1/2” Slots 6mm x 13mmUnit legs are removable from units installed for horiziontal air

2” 51mm

2” 51mm

31 1/4” 790mm

37 1/2” 950mm

27 5/8” 700mm2 7/16”

62mm

9/16” 14mm

15 1/4” 390mm

7/16” Diameter Hole 11mm

8” 200mm

22” 590mm

43” 1,090mm

24 1/2” 620mm

16” 410mm

21 1/2” 550mm

9” 230mm 1”

25mm

8” 200mm

Optional External Electrical

Box

A

E 34”

860mm

7/8” Diameter Holes 22mm

17” 430mm

9” 230mm

1” 25mm

43” 1,090mm

42 1/2” 1,080mm

7/8” Diameter Holes 22mm

37 1/2” 950mm2 1/2”

64mm

A

E

Diagram 1.Dimensions for DVT Models 001 through 003

Diagram 2.Dimensions for DVT Models 005 through 026 with Vertical Air Flow

Diagram 3.Dimensions for DVT Models 005 through 026 with Horizontal Flow

Note: These models could have 1,2 or 3 fans - see table 6

Note: These models could have 1,2 or 3 fans - see table 6

DIMENSIONAL DATA

7 7

Table 6. Physical Specifications

1 Motor voltage 208-230/1/60; 1075 RPM 2 Motor voltage 208-230-460/3/60; 1140 RPM 3 Motor Voltage 575/3/60; 1140 RPM

Note: DVT 001-002 available in 115/1/60 voltage;

Condenser Fan Cycling DVT models 010 to 026 condensers are available with either ambient or pressure activated fan cycling packages. Head pressure can be controlled by varying the air flow across the coil in response to changes in ambient temperatures or refrigerant pressures. See Table 7 below for minimum ambients for fan cycling.

Table 7. Minimum Ambient for Fan Cycling (90º F./32ºC.Condensing Temperature)

DVT Models Fans

Design T.D.

30°F./ 17°C. 25°F./ 15°C. 20°F./ 12°C. 15°F./ 8°C. 10°F./ 6°C.

010, 012, 014, 016 2 35 2 45 7 55 13 60 16 70 21

021, 023, 026 3 15 -9 30 -1 40 4 55 13 65 18

DVT

Models

CFM/m³h

Fan Motor Data

No.

Dia.

In./mm

HP1 FLA1 HP2 FLA2 HP3 FLA3

001 2400 4100 1 18 460 1/4 2.0 --- --- --- ---

002 2400 4100 1 18 460 1/4 2.0 --- --- --- ---

003 2100 3600 1 18 460 1/4 2.0 --- --- --- ---

005 5050 8600 1 24 610 1/3 3.4 1/3 2.6/1.3 1/3 1.0

008 6450 11000 1 26 660 1/2 3.9 1/3 2.6/1.3 1/3 1.0

010 10100 17200 2 24 610 1/3 6.8 1/3 5.2/2.6 1/3 1.9

012 12400 21100 2 26 660 1/2 7.8 1/3 5.2/2.6 1/3 1.9

014 13700 23300 2 26 660 1/2 7.8 1/3 5.2/2.6 1/3 1.9

016 12900 21900 2 26 660 1/2 7.8 1/3 5.2/2.6 1/3 1.9

021 20500 34800 3 26 660 1/2 11.7 1/3 7.8/3.9 1/3 2.9

023 19900 33800 3 26 660 1/2 11.7 1/3 7.8/3.9 1/3 2.9

026 19400 33000 3 26 660 1/2 11.7 1/3 7.8/3.9 1/3 2.9

DVT

Models

Dimensions Inches/mm

Connections ODS (In.) Max.

Feeds Avail.

Approx.Net Wt.

Lbs./kg

A E Inlet Oulet

001 --- --- 3/8 3/8 1 96 44

002 --- --- 7/8 5/8 2 96 44

003 --- --- 7/8 5/8 4 114 52

005 40 1010 30 760 1-1/8 7/8 8 180 82

008 50 1260 40 1020 1-1/8 7/8 16 260 118

010 70 1770 60 1520 (2) 1-1/8 (2) 7/8 16 450 204

012 70 1770 60 1520 (2) 1-1/8 (2) 7/8 16 470 213

014 90 2280 80 2030 (2) 1-1/8 (2) 7/8 16 510 231

016 90 2280 80 2030 (2) 1-3/8 (2) 1-1/8 32 530 240

021 130 3300 120 3050 (2) 1-5/8 (2) 1-1/8 24 550 249

023 130 3300 120 3050 (2) 1-5/8 (2) 1-1/8 24 580 263

026 130 3300 120 3050 (2) 1-5/8 (2) 1-1/8 32 625 284

CONDENSER SPECIFICATION / CONDENSER FAN CYCLING

2175 West Park Place Blvd.· Stone Mountain, GA 30087 Phone: 800.537.7775 · Fax: 770.465.5900 heatcraftrpd.com

Since product improvement is a continuing effort, we reserve the right to make changes in specifications without notice.

BN-RACCTB | September 2016